1Exynos Display Controller
2=========================
3Required properties:
4SOC specific:
5	compatible: should be "samsung,exynos-fimd"
6	reg: Base address of FIMD IP.
7
8Board(panel specific):
9	samsung,vl-col: X resolution of the panel
10	samsung,vl-row: Y resolution of the panel
11	samsung,vl-freq: Refresh rate
12	samsung,vl-bpix: Bits per pixel
13	samsung,vl-hspw: Hsync value
14	samsung,vl-hfpd: Right margin
15	samsung,vl-hbpd: Left margin
16	samsung,vl-vspw: Vsync value
17	samsung,vl-vfpd: Lower margin
18	samsung,vl-vbpd: Upper margin
19
20Optional properties:
21Board(panel specific):
22	samsung,vl-width: width of display area in mm
23	samsung,vl-height: Height of display area in mm
24
25	samsung,vl-clkp: Clock polarity
26		CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
27	samsung,vl-oep: Output Enable polarity
28		CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
29	samsung,vl-hsp: Horizontal Sync polarity
30		CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
31	samsung,vl-vsp: Vertical Sync polarity
32		CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
33	samsung,vl-dp: Data polarity
34		CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
35
36	samsung,vl-cmd-allow-len: Wait end of frame
37	samsung,winid: Window number on which data is to be displayed
38	samsung,init-delay: Delay before LCD initialization starts
39	samsung,power-on-delay: Delay after LCD is powered on
40	samsung,reset-delay: Delay after LCD is reset
41	samsung,interface-mode: 1(FIMD_RGB_INTERFACE), 2(FIMD_CPU_INTERFACE)
42	samsung,mipi-enabled: 1 if you want to use MIPI, else 0
43	samsung,dp-enabled: 1is you want to use DP, else 0
44	samsung,cs-setup: cs_setup value in FIMD_CPU_INTERFACE mode.
45	samsung,wr-setup: wr_setup value in FIMD_CPU_INTERFACE mode.
46	samsung,wr-act: wr_act value in FIMD_CPU_INTERFACE mode.
47	samsung,wr-hold: wr_hold value in FIMD_CPU_INTERFACE mode.
48	samsung,logo-on: 1 if you want to use custom logo.
49			 0 if you want LCD console.
50	samsung,logo-width: pixel width of logo image. Valid if logo_on = 1
51	samsung,logo-height: pixel height of logo image. Valid if logo_on = 1
52	samsung,logo-addr: Address of logo image. Valid if logo_on = 1
53	samsung,rgb-mode: 0(MODE_RGB_P), 1(MODE_BGR_P),
54			  2(MODE_RGB_S), 3(MODE_BGR_S)
55	samsung,pclk-name: parent clock identifier: 1(MPLL), 2(EPLL), 3(VPLL)
56	samsung,sclk-div: parent_clock/source_clock ratio
57	samsung,dual-lcd-enabled: 1 if you support two LCD, else 0
58	samsung,disable-sysmmu: Define this if you want to disable FIMD sysmmu.
59				(needed for Exynos5420 and newer versions)
60				Add the required FIMD sysmmu nodes to be
61				disabled with compatible string
62				"samsung,sysmmu-v3.3", with a "reg" property
63				holding the register address of FIMD sysmmu.
64
65Example:
66SOC specific part:
67	fimd@14400000 {
68		compatible = "samsung,exynos-fimd";
69		reg = <0x14400000 0x10000>;
70		#address-cells = <1>;
71		#size-cells = <1>;
72	};
73
74Board specific part:
75	fimd@14400000 {
76		samsung,vl-freq = <60>;
77		samsung,vl-col = <2560>;
78		samsung,vl-row = <1600>;
79		samsung,vl-width = <2560>;
80		samsung,vl-height = <1600>;
81
82		samsung,vl-clkp;
83		samsung,vl-dp;
84		samsung,vl-bpix = <4>;
85
86		samsung,vl-hspw = <32>;
87		samsung,vl-hbpd = <80>;
88		samsung,vl-hfpd = <48>;
89		samsung,vl-vspw = <6>;
90		samsung,vl-vbpd = <37>;
91		samsung,vl-vfpd = <3>;
92		samsung,vl-cmd-allow-len = <0xf>;
93
94		samsung,winid = <3>;
95		samsung,interface-mode = <1>;
96		samsung,dp-enabled = <1>;
97		samsung,dual-lcd-enabled = <0>;
98	};
99