1This file contains information for VSC9953, a Vitesse L2 Switch IP 2which is integrated in the T1040/T1020 Freescale SoCs. 3 4About Device: 5============= 6VSC9953 is an 8-port Gigabit Ethernet switch supports the following features: 7 - 8192 MAC addresses 8 - Static Address provisioning 9 - Dynamic learning of MAC addresses and aging 10 - 4096 VLANs 11 - Independent and shared VLAN learning (IVL, SVL) 12 - Policing with storm control and MC/BC protection 13 - IPv4 and IPv6 multicast 14 - Jumbo frames (9.6 KB) 15 - Access Control List 16 - VLAN editing, translation and remarking 17 - RMON counters per port 18 19Switch interfaces: 20 - 8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs 21 - 2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links) 22 to FMan ports (FM1@DTSEC1 and FM1@DTSEC2) 23 24Commands Overview: 25============= 26Commands supported 27 - enable/disable a port or show its configuration (speed, duplexity, status, etc.) 28 - port statistics 29 - MAC learning 30 - add/remove FDB entries 31 - Port-based VLAN 32 - Private/Shared VLAN learning 33 - VLAN ingress filtering 34 - Port LAG 35 36Commands syntax 37ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration 38ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics 39ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port 40ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries; 41 if [vlan <vid>] is missing, VID 1 will be used 42ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port 43ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members) 44ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port 45ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag. 46 Tag's VID could be the frame's classified VID or the PVID of the port 47ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private 48ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port 49ethsw [port <port_no>] aggr { [help] | show | <lag_group_no> } - get/set LAG group for a port 50 51=> ethsw show 52 Port Status Link Speed Duplex 53 0 enabled down 10 half 54 1 enabled down 10 half 55 2 enabled down 10 half 56 3 enabled up 1000 full 57 4 disabled down - half 58 5 disabled down - half 59 6 disabled down - half 60 7 disabled down - half 61 8 enabled up 2500 full 62 9 enabled up 2500 full 63=> 64