xref: /openbmc/u-boot/doc/README.t1040-l2switch (revision 1221ce45)
1This file contains information for VSC9953, a Vitesse L2 Switch IP
2which is integrated in the T1040/T1020 Freescale SoCs.
3
4About Device:
5=============
6VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
7	-	8192 MAC addresses
8	-	Static Address provisioning
9	-	Dynamic learning of MAC addresses and aging
10	-	4096 VLANs
11	-	Independent and shared VLAN learning (IVL, SVL)
12	-	Policing with storm control and MC/BC protection
13	-	IPv4 and IPv6 multicast
14	-	Jumbo frames (9.6 KB)
15	-	Access Control List
16	-	VLAN editing, translation and remarking
17	-	RMON counters per port
18
19Switch interfaces:
20	-	8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs
21	-	2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links)
22		to FMan ports (FM1@DTSEC1 and FM1@DTSEC2)
23
24Commands Overview:
25=============
26Commands supported
27	- enable/disable a port or show its configuration (speed, duplexity, status, etc.)
28	- port statistics
29	- MAC learning
30	- add/remove FDB entries
31	- Port-based VLAN
32	- Private/Shared VLAN learning
33	- VLAN ingress filtering
34	- Port LAG
35
36Commands syntax
37ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration
38ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics
39ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port
40ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries;
41											  if [vlan <vid>] is missing, VID 1 will be used
42ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port
43ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members)
44ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port
45ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag.
46									  Tag's VID could be the frame's classified VID or the PVID of the port
47ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private
48ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port
49ethsw [port <port_no>] aggr { [help] | show | <lag_group_no> } - get/set LAG group for a port
50
51=> ethsw show
52    Port   Status     Link    Speed   Duplex
53       0  enabled     down       10     half
54       1  enabled     down       10     half
55       2  enabled     down       10     half
56       3  enabled       up     1000     full
57       4 disabled     down        -     half
58       5 disabled     down        -     half
59       6 disabled     down        -     half
60       7 disabled     down        -     half
61       8  enabled       up     2500     full
62       9  enabled       up     2500     full
63=>
64