1# 2# Copyright (C) 2015 Google. Inc 3# Written by Simon Glass <sjg@chromium.org> 4# 5# SPDX-License-Identifier: GPL-2.0+ 6# 7 8U-Boot on Rockchip 9================== 10 11There are several repositories available with versions of U-Boot that support 12many Rockchip devices [1] [2]. 13 14The current mainline support is experimental only and is not useful for 15anything. It should provide a base on which to build. 16 17So far only support for the RK3288 and RK3036 is provided. 18 19 20Prerequisites 21============= 22 23You will need: 24 25 - Firefly RK3288 board or something else with a supported RockChip SoC 26 - Power connection to 5V using the supplied micro-USB power cable 27 - Separate USB serial cable attached to your computer and the Firefly 28 (connect to the micro-USB connector below the logo) 29 - rkflashtool [3] 30 - openssl (sudo apt-get install openssl) 31 - Serial UART connection [4] 32 - Suitable ARM cross compiler, e.g.: 33 sudo apt-get install gcc-4.7-arm-linux-gnueabi 34 35 36Building 37======== 38 39At present seven RK3288 boards are supported: 40 41 - EVB RK3288 - use evb-rk3288 configuration 42 - Fennec RK3288 - use fennec-rk3288 configuration 43 - Firefly RK3288 - use firefly-rk3288 configuration 44 - Hisense Chromebook - use chromebook_jerry configuration 45 - Tinker RK3288 - use tinker-rk3288 configuration 46 - PopMetal RK3288 - use popmetal-rk3288 configuration 47 - Radxa Rock 2 - use rock2 configuration 48 49Two RK3036 board are supported: 50 51 - EVB RK3036 - use evb-rk3036 configuration 52 - Kylin - use kylin_rk3036 configuration 53 54For example: 55 56 CROSS_COMPILE=arm-linux-gnueabi- make O=firefly firefly-rk3288_defconfig all 57 58(or you can use another cross compiler if you prefer) 59 60 61Writing to the board with USB 62============================= 63 64For USB to work you must get your board into ROM boot mode, either by erasing 65your MMC or (perhaps) holding the recovery button when you boot the board. 66To erase your MMC, you can boot into Linux and type (as root) 67 68 dd if=/dev/zero of=/dev/mmcblk0 bs=1M 69 70Connect your board's OTG port to your computer. 71 72To create a suitable image and write it to the board: 73 74 ./firefly-rk3288/tools/mkimage -n rk3288 -T rkimage -d \ 75 ./firefly-rk3288/spl/u-boot-spl-dtb.bin out && \ 76 cat out | openssl rc4 -K 7c4e0304550509072d2c7b38170d1711 | rkflashtool l 77 78If all goes well you should something like: 79 80 U-Boot SPL 2015.07-rc1-00383-ge345740-dirty (Jun 03 2015 - 10:06:49) 81 Card did not respond to voltage select! 82 spl: mmc init failed with error: -17 83 ### ERROR ### Please RESET the board ### 84 85You will need to reset the board before each time you try. Yes, that's all 86it does so far. If support for the Rockchip USB protocol or DFU were added 87in SPL then we could in principle load U-Boot and boot to a prompt from USB 88as several other platforms do. However it does not seem to be possible to 89use the existing boot ROM code from SPL. 90 91 92Booting from an SD card 93======================= 94 95To write an image that boots from an SD card (assumed to be /dev/sdc): 96 97 ./firefly-rk3288/tools/mkimage -n rk3288 -T rksd -d \ 98 firefly-rk3288/spl/u-boot-spl-dtb.bin out && \ 99 sudo dd if=out of=/dev/sdc seek=64 && \ 100 sudo dd if=firefly-rk3288/u-boot-dtb.img of=/dev/sdc seek=256 101 102This puts the Rockchip header and SPL image first and then places the U-Boot 103image at block 256 (i.e. 128KB from the start of the SD card). This 104corresponds with this setting in U-Boot: 105 106 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 256 107 108Put this SD (or micro-SD) card into your board and reset it. You should see 109something like: 110 111 U-Boot 2016.01-rc2-00309-ge5bad3b-dirty (Jan 02 2016 - 23:41:59 -0700) 112 113 Model: Radxa Rock 2 Square 114 DRAM: 2 GiB 115 MMC: dwmmc@ff0f0000: 0, dwmmc@ff0c0000: 1 116 *** Warning - bad CRC, using default environment 117 118 In: serial 119 Out: vop@ff940000.vidconsole 120 Err: serial 121 Net: Net Initialization Skipped 122 No ethernet found. 123 Hit any key to stop autoboot: 0 124 => 125 126The rockchip bootrom can load and boot an initial spl, then continue to 127load a second-level bootloader(ie. U-BOOT) as soon as it returns to bootrom. 128Therefore RK3288 has another loading sequence like RK3036. The option of 129U-Boot is controlled with this setting in U-Boot: 130 131 #define CONFIG_ROCKCHIP_SPL_BACK_TO_BROM 132 133You can create the image via the following operations: 134 135 ./firefly-rk3288/tools/mkimage -n rk3288 -T rksd -d \ 136 firefly-rk3288/spl/u-boot-spl-dtb.bin out && \ 137 cat firefly-rk3288/u-boot-dtb.bin >> out && \ 138 sudo dd if=out of=/dev/sdc seek=64 139 140If you have an HDMI cable attached you should see a video console. 141 142For evb_rk3036 board: 143 ./evb-rk3036/tools/mkimage -n rk3036 -T rksd -d evb-rk3036/spl/u-boot-spl.bin out && \ 144 cat evb-rk3036/u-boot-dtb.bin >> out && \ 145 sudo dd if=out of=/dev/sdc seek=64 146 147Note: rk3036 SDMMC and debug uart use the same iomux, so if you boot from SD, the 148 debug uart must be disabled 149 150Using fastboot on rk3288 151======================== 152- Write GPT partition layout to mmc device which fastboot want to use it to 153store the image 154 155 => gpt write mmc 1 $partitions 156 157- Invoke fastboot command to prepare 158 159 => fastboot 1 160 161- Start fastboot request on PC 162 163 fastboot -i 0x2207 flash loader evb-rk3288/spl/u-boot-spl-dtb.bin 164 165You should see something like: 166 167 => fastboot 1 168 WARNING: unknown variable: partition-type:loader 169 Starting download of 357796 bytes 170 .. 171 downloading of 357796 bytes finished 172 Flashing Raw Image 173 ........ wrote 357888 bytes to 'loader' 174 175Booting from SPI 176================ 177 178To write an image that boots from SPI flash (e.g. for the Haier Chromebook): 179 180 ./chromebook_jerry/tools/mkimage -n rk3288 -T rkspi \ 181 -d chromebook_jerry/spl/u-boot-spl-dtb.bin spl.bin && \ 182 dd if=spl.bin of=spl-out.bin bs=128K conv=sync && \ 183 cat spl-out.bin chromebook_jerry/u-boot-dtb.img >out.bin && \ 184 dd if=out.bin of=out.bin.pad bs=4M conv=sync 185 186This converts the SPL image to the required SPI format by adding the Rockchip 187header and skipping every 2KB block. Then the U-Boot image is written at 188offset 128KB and the whole image is padded to 4MB which is the SPI flash size. 189The position of U-Boot is controlled with this setting in U-Boot: 190 191 #define CONFIG_SYS_SPI_U_BOOT_OFFS (128 << 10) 192 193If you have a Dediprog em100pro connected then you can write the image with: 194 195 sudo em100 -s -c GD25LQ32 -d out.bin.pad -r 196 197When booting you should see something like: 198 199 U-Boot SPL 2015.07-rc2-00215-g9a58220-dirty (Jun 23 2015 - 12:11:32) 200 201 202 U-Boot 2015.07-rc2-00215-g9a58220-dirty (Jun 23 2015 - 12:11:32 -0600) 203 204 Model: Google Jerry 205 DRAM: 2 GiB 206 MMC: 207 Using default environment 208 209 In: serial@ff690000 210 Out: serial@ff690000 211 Err: serial@ff690000 212 => 213 214Future work 215=========== 216 217Immediate priorities are: 218 219- USB host 220- USB device 221- Run CPU at full speed (code exists but we only see ~60 DMIPS maximum) 222- NAND flash 223- Support for other Rockchip parts 224- Boot U-Boot proper over USB OTG (at present only SPL works) 225 226 227Development Notes 228================= 229 230There are plenty of patches in the links below to help with this work. 231 232[1] https://github.com/rkchrome/uboot.git 233[2] https://github.com/linux-rockchip/u-boot-rockchip.git branch u-boot-rk3288 234[3] https://github.com/linux-rockchip/rkflashtool.git 235[4] http://wiki.t-firefly.com/index.php/Firefly-RK3288/Serial_debug/en 236 237rkimage 238------- 239 240rkimage.c produces an SPL image suitable for sending directly to the boot ROM 241over USB OTG. This is a very simple format - just the string RK32 (as 4 bytes) 242followed by u-boot-spl-dtb.bin. 243 244The boot ROM loads image to 0xff704000 which is in the internal SRAM. The SRAM 245starts at 0xff700000 and extends to 0xff718000 where we put the stack. 246 247rksd 248---- 249 250rksd.c produces an image consisting of 32KB of empty space, a header and 251u-boot-spl-dtb.bin. The header is defined by 'struct header0_info' although 252most of the fields are unused by U-Boot. We just need to specify the 253signature, a flag and the block offset and size of the SPL image. 254 255The header occupies a single block but we pad it out to 4 blocks. The header 256is encoding using RC4 with the key 7c4e0304550509072d2c7b38170d1711. The SPL 257image can be encoded too but we don't do that. 258 259The maximum size of u-boot-spl-dtb.bin which the boot ROM will read is 32KB, 260or 0x40 blocks. This is a severe and annoying limitation. There may be a way 261around this limitation, since there is plenty of SRAM, but at present the 262board refuses to boot if this limit is exceeded. 263 264The image produced is padded up to a block boundary (512 bytes). It should be 265written to the start of an SD card using dd. 266 267Since this image is set to load U-Boot from the SD card at block offset, 268CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR, dd should be used to write 269u-boot-dtb.img to the SD card at that offset. See above for instructions. 270 271rkspi 272----- 273 274rkspi.c produces an image consisting of a header and u-boot-spl-dtb.bin. The 275resulting image is then spread out so that only the first 2KB of each 4KB 276sector is used. The header is the same as with rksd and the maximum size is 277also 32KB (before spreading). The image should be written to the start of 278SPI flash. 279 280See above for instructions on how to write a SPI image. 281 282rkmux.py 283-------- 284 285You can use this script to create #defines for SoC register access. See the 286script for usage. 287 288 289Device tree and driver model 290---------------------------- 291 292Where possible driver model is used to provide a structure to the 293functionality. Device tree is used for configuration. However these have an 294overhead and in SPL with a 32KB size limit some shortcuts have been taken. 295In general all Rockchip drivers should use these features, with SPL-specific 296modifications where required. 297 298GPT partition layout 299---------------------------- 300 301Rockchip use a unified GPT partition layout in open source support. 302With this GPT partition layout, uboot can be compatilbe with other components, 303like miniloader, trusted-os, arm-trust-firmware. 304 305There are some documents about partitions in the links below. 306http://rockchip.wikidot.com/partitions 307 308-- 309Simon Glass <sjg@chromium.org> 31024 June 2015 311