xref: /openbmc/u-boot/doc/README.fsl-ddr (revision 643ad899)
1Table of interleaving 2-4 controllers
2=====================================
3  +--------------+-----------------------------------------------------------+
4  |Configuration |                    Memory Controller                      |
5  |              |       1              2              3             4       |
6  |--------------+--------------+--------------+-----------------------------+
7  | Two memory   | Not Intlv'ed | Not Intlv'ed |                             |
8  | complexes    +--------------+--------------+                             |
9  |              |      2-way Intlv'ed         |                             |
10  |--------------+--------------+--------------+--------------+              |
11  |              | Not Intlv'ed | Not Intlv'ed | Not Intlv'ed |              |
12  | Three memory +--------------+--------------+--------------+              |
13  | complexes    |         2-way Intlv'ed      | Not Intlv'ed |              |
14  |              +-----------------------------+--------------+              |
15  |              |                  3-way Intlv'ed            |              |
16  +--------------+--------------+--------------+--------------+--------------+
17  |              | Not Intlv'ed | Not Intlv'ed | Not Intlv'ed | Not Intlv'ed |
18  | Four memory  +--------------+--------------+--------------+--------------+
19  | complexes    |       2-way Intlv'ed        |       2-way Intlv'ed        |
20  |              +-----------------------------+-----------------------------+
21  |              |                      4-way Intlv'ed                       |
22  +--------------+-----------------------------------------------------------+
23
24
25Table of 2-way interleaving modes supported in cpu/8xxx/ddr/
26======================================================
27  +-------------+---------------------------------------------------------+
28  |		|		    Rank Interleaving			  |
29  |		+--------+-----------+-----------+------------+-----------+
30  |Memory	|	 |	     |		 |    2x2     |    4x1	  |
31  |Controller	|  None  | 2x1 lower | 2x1 upper | {CS0+CS1}, | {CS0+CS1+ |
32  |Interleaving |	 | {CS0+CS1} | {CS2+CS3} | {CS2+CS3}  |  CS2+CS3} |
33  +-------------+--------+-----------+-----------+------------+-----------+
34  |None		|  Yes	 | Yes	     | Yes	 | Yes	      | Yes	  |
35  +-------------+--------+-----------+-----------+------------+-----------+
36  |Cacheline	|  Yes	 | Yes	     | No	 | No, Only(*)| Yes	  |
37  |		|CS0 Only|	     |		 | {CS0+CS1}  |		  |
38  +-------------+--------+-----------+-----------+------------+-----------+
39  |Page		|  Yes	 | Yes	     | No	 | No, Only(*)| Yes	  |
40  |		|CS0 Only|	     |		 | {CS0+CS1}  |		  |
41  +-------------+--------+-----------+-----------+------------+-----------+
42  |Bank		|  Yes	 | Yes	     | No	 | No, Only(*)| Yes	  |
43  |		|CS0 Only|	     |		 | {CS0+CS1}  |		  |
44  +-------------+--------+-----------+-----------+------------+-----------+
45  |Superbank	|  No	 | Yes	     | No	 | No, Only(*)| Yes	  |
46  |		|	 |	     |		 | {CS0+CS1}  |		  |
47  +-------------+--------+-----------+-----------+------------+-----------+
48 (*) Although the hardware can be configured with memory controller
49 interleaving using "2x2" rank interleaving, it only interleaves {CS0+CS1}
50 from each controller. {CS2+CS3} on each controller are only rank
51 interleaved on that controller.
52
53 For memory controller interleaving, identical DIMMs are suggested. Software
54 doesn't check the size or organization of interleaved DIMMs.
55
56The ways to configure the ddr interleaving mode
57==============================================
581. In board header file(e.g.MPC8572DS.h), add default interleaving setting
59   under "CONFIG_EXTRA_ENV_SETTINGS", like:
60	#define CONFIG_EXTRA_ENV_SETTINGS				\
61	 "hwconfig=fsl_ddr:ctlr_intlv=bank"			\
62	 ......
63
642. Run u-boot "setenv" command to configure the memory interleaving mode.
65   Either numerical or string value is accepted.
66
67  # disable memory controller interleaving
68  setenv hwconfig "fsl_ddr:ctlr_intlv=null"
69
70  # cacheline interleaving
71  setenv hwconfig "fsl_ddr:ctlr_intlv=cacheline"
72
73  # page interleaving
74  setenv hwconfig "fsl_ddr:ctlr_intlv=page"
75
76  # bank interleaving
77  setenv hwconfig "fsl_ddr:ctlr_intlv=bank"
78
79  # superbank
80  setenv hwconfig "fsl_ddr:ctlr_intlv=superbank"
81
82  # 1KB 3-way interleaving
83  setenv hwconfig "fsl_ddr:ctlr_intlv=3way_1KB"
84
85  # 4KB 3-way interleaving
86  setenv hwconfig "fsl_ddr:ctlr_intlv=3way_4KB"
87
88  # 8KB 3-way interleaving
89  setenv hwconfig "fsl_ddr:ctlr_intlv=3way_8KB"
90
91  # disable bank (chip-select) interleaving
92  setenv hwconfig "fsl_ddr:bank_intlv=null"
93
94  # bank(chip-select) interleaving cs0+cs1
95  setenv hwconfig "fsl_ddr:bank_intlv=cs0_cs1"
96
97  # bank(chip-select) interleaving cs2+cs3
98  setenv hwconfig "fsl_ddr:bank_intlv=cs2_cs3"
99
100  # bank(chip-select) interleaving (cs0+cs1) and (cs2+cs3)  (2x2)
101  setenv hwconfig "fsl_ddr:bank_intlv=cs0_cs1_and_cs2_cs3"
102
103  # bank(chip-select) interleaving (cs0+cs1+cs2+cs3) (4x1)
104  setenv hwconfig "fsl_ddr:bank_intlv=cs0_cs1_cs2_cs3"
105
106  # bank(chip-select) interleaving (auto)
107  setenv hwconfig "fsl_ddr:bank_intlv=auto"
108  This auto mode only select from cs0_cs1_cs2_cs3, cs0_cs1, null dependings
109  on DIMMs.
110
111Memory controller address hashing
112==================================
113If the DDR controller supports address hashing, it can be enabled by hwconfig.
114
115Syntax is:
116hwconfig=fsl_ddr:addr_hash=true
117
118Memory controller ECC on/off
119============================
120If ECC is enabled in board configuratoin file, i.e. #define CONFIG_DDR_ECC,
121ECC can be turned on/off by hwconfig.
122
123Syntax is
124hwconfig=fsl_ddr:ecc=off
125
126Memory testing options for mpc85xx
127==================================
1281. Memory test can be done once U-boot prompt comes up using mtest, or
1292. Memory test can be done with Power-On-Self-Test function, activated at
130   compile time.
131
132   In order to enable the POST memory test, CONFIG_POST needs to be
133   defined in board configuraiton header file. By default, POST memory test
134   performs a fast test. A slow test can be enabled by changing the flag at
135   compiling time. To test memory bigger than 2GB, 36BIT support is needed.
136   Memory is tested within a 2GB window. TLBs are used to map the virtual 2GB
137   window to physical address so that all physical memory can be tested.
138
139Combination of hwconfig
140=======================
141Hwconfig can be combined with multiple parameters, for example, on a supported
142platform
143
144hwconfig=fsl_ddr:addr_hash=true,ctlr_intlv=cacheline,bank_intlv=cs0_cs1_cs2_cs3,ecc=on
145
146Table for dynamic ODT for DDR3
147==============================
148For single-slot system with quad-rank DIMM and dual-slot system, dynamic ODT may
149be needed, depending on the configuration. The numbers in the following tables are
150in Ohms.
151
152* denotes dynamic ODT
153
154Two slots system
155+-----------------------+----------+---------------+-----------------------------+-----------------------------+
156|     Configuration	|	   |DRAM controller|	       Slot 1		 |	      Slot 2	       |
157+-----------+-----------+----------+-------+-------+--------------+--------------+--------------+--------------+
158|	    |		|	   |	   |	   |	 Rank 1   |	Rank 2	 |   Rank 1	|    Rank 2    |
159+  Slot 1   |	Slot 2	|Write/Read| Write | Read  |-------+------+-------+------+-------+------+-------+------+
160|	    |		|	   |	   |	   | Write | Read | Write | Read | Write | Read | Write | Read |
161+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
162|	    |		|  Slot 1  |  off  | 75    | 120   | off  | off   | off  | off	 | off	| 30	| 30   |
163| Dual Rank | Dual Rank |----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
164|	    |		|  Slot 2  |  off  | 75    | off   | off  | 30	  | 30	 | 120	 | off	| off	| off  |
165+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
166|	    |		|  Slot 1  |  off  | 75    | 120   | off  | off   | off  | 20	 | 20	|	|      |
167| Dual Rank |Single Rank|----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
168|	    |		|  Slot 2  |  off  | 75    | off   | off  | 20	  | 20	 | 120	*| off	|	|      |
169+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
170|	    |		|  Slot 1  |  off  | 75    | 120  *| off  |	  |	 | off	 | off	| 20	| 20   |
171|Single Rank| Dual Rank |----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
172|	    |		|  Slot 2  |  off  | 75    | 20    | 20   |	  |	 | 120	 | off	| off	| off  |
173+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
174|	    |		|  Slot 1  |  off  | 75    | 120  *| off  |	  |	 | 30	 | 30	|	|      |
175|Single Rank|Single Rank|----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
176|	    |		|  Slot 2  |  off  | 75    | 30    | 30   |	  |	 | 120	*| off	|	|      |
177+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
178| Dual Rank |	Empty	|  Slot 1  |  off  | 75    | 40    | off  | off   | off  |	 |	|	|      |
179+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
180|   Empty   | Dual Rank |  Slot 2  |  off  | 75    |	   |	  |	  |	 | 40	 | off	| off	| off  |
181+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
182|Single Rank|	Empty	|  Slot 1  |  off  | 75    | 40    | off  |	  |	 |	 |	|	|      |
183+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
184|   Empty   |Single Rank|  Slot 2  |  off  | 75    |	   |	  |	  |	 | 40	 | off	|	|      |
185+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
186
187Single slot system
188+-------------+------------+---------------+-----------------------------+-----------------------------+
189|	      |		   |DRAM controller|	 Rank 1   |    Rank 2	 |    Rank 3	|    Rank 4    |
190|Configuration| Write/Read |-------+-------+-------+------+-------+------+-------+------+-------+------+
191|	      |		   | Write | Read  | Write | Read | Write | Read | Write | Read | Write | Read |
192+-------------+------------+-------+-------+-------+------+-------+------+-------+------+-------+------+
193|	      |   R1	   | off   | 75    | 120  *| off  | off   | off  | 20	 | 20	| off	| off  |
194|	      |------------+-------+-------+-------+------+-------+------+-------+------+-------+------+
195|	      |   R2	   | off   | 75    | off   | 20   | 120   | off  | 20	 | 20	| off	| off  |
196|  Quad Rank  |------------+-------+-------+-------+------+-------+------+-------+------+-------+------+
197|	      |   R3	   | off   | 75    | 20    | 20   | off   | off  | 120	*| off	| off	| off  |
198|	      |------------+-------+-------+-------+------+-------+------+-------+------+-------+------+
199|	      |   R4	   | off   | 75    | 20    | 20   | off   | off  | off	 | 20	| 120	| off  |
200+-------------+------------+-------+-------+-------+------+-------+------+-------+------+-------+------+
201|	      |   R1	   | off   | 75    | 40    | off  | off   | off  |
202|  Dual Rank  |------------+-------+-------+-------+------+-------+------+
203|	      |   R2	   | off   | 75    | 40    | off  | off   | off  |
204+-------------+------------+-------+-------+-------+------+-------+------+
205| Single Rank |   R1	   | off   | 75    | 40    | off  |
206+-------------+------------+-------+-------+-------+------+
207
208Reference http://www.xrosstalkmag.com/mag_issues/xrosstalk_oct08_final.pdf
209	  http://download.micron.com/pdf/technotes/ddr3/tn4108_ddr3_design_guide.pdf
210
211
212Table for ODT for DDR2
213======================
214Two slots system
215+-----------------------+----------+---------------+-----------------------------+-----------------------------+
216|     Configuration     |          |DRAM controller|           Slot 1            |            Slot 2           |
217+-----------+-----------+----------+-------+-------+--------------+--------------+--------------+--------------+
218|           |           |          |       |       |     Rank 1   |     Rank 2   |   Rank 1     |    Rank 2    |
219+  Slot 1   |   Slot 2  |Write/Read| Write | Read  |-------+------+-------+------+-------+------+-------+------+
220|           |           |          |       |       | Write | Read | Write | Read | Write | Read | Write | Read |
221+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
222|           |           |  Slot 1  |  off  | 150   | off   | off  | off   | off  | 75    | 75   | off   | off  |
223| Dual Rank | Dual Rank |----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
224|           |           |  Slot 2  |  off  | 150   | 75    | 75   | off   | off  | off   | off  | off   | off  |
225+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
226|           |           |  Slot 1  |  off  | 150   | off   | off  | off   | off  | 75    | 75   |       |      |
227| Dual Rank |Single Rank|----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
228|           |           |  Slot 2  |  off  | 150   | 75    | 75   | off   | off  | off   | off  |       |      |
229+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
230|           |           |  Slot 1  |  off  | 150   | off   | off  |       |      | 75    | 75   | off   | off  |
231|Single Rank| Dual Rank |----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
232|           |           |  Slot 2  |  off  | 150   | 75    | 75   |       |      | off   | off  | off   | off  |
233+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
234|           |           |  Slot 1  |  off  | 150   | off   | off  |       |      | 75    | 75   |       |      |
235|Single Rank|Single Rank|----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
236|           |           |  Slot 2  |  off  | 150   | 75    | 75   |       |      | off   | off  |       |      |
237+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
238| Dual Rank |   Empty   |  Slot 1  |  off  | 75    | 150   | off  | off   | off  |       |      |       |      |
239+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
240|   Empty   | Dual Rank |  Slot 2  |  off  | 75    |       |      |       |      | 150   | off  | off   | off  |
241+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
242|Single Rank|   Empty   |  Slot 1  |  off  | 75    | 150   | off  |       |      |       |      |       |      |
243+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
244|   Empty   |Single Rank|  Slot 2  |  off  | 75    |       |      |       |      | 150   | off  |       |      |
245+-----------+-----------+----------+-------+-------+-------+------+-------+------+-------+------+-------+------+
246
247Single slot system
248+-------------+------------+---------------+-----------------------------+
249|             |            |DRAM controller|     Rank 1   |    Rank 2    |
250|Configuration| Write/Read |-------+-------+-------+------+-------+------+
251|             |            | Write | Read  | Write | Read | Write | Read |
252+-------------+------------+-------+-------+-------+------+-------+------+
253|             |   R1       | off   | 75    | 150   | off  | off   | off  |
254|  Dual Rank  |------------+-------+-------+-------+------+-------+------+
255|             |   R2       | off   | 75    | 150   | off  | off   | off  |
256+-------------+------------+-------+-------+-------+------+-------+------+
257| Single Rank |   R1       | off   | 75    | 150   | off  |
258+-------------+------------+-------+-------+-------+------+
259
260Reference http://www.samsung.com/global/business/semiconductor/products/dram/downloads/applicationnote/ddr2_odt_control_200603.pdf
261
262
263Interactive DDR debugging
264===========================
265
266For DDR parameter tuning up and debugging, the interactive DDR debugger can
267be activated by setting the environment variable "ddr_interactive" to any
268value.  (The value of ddr_interactive may have a meaning in the future, but,
269for now, the presence of the variable will cause the debugger to run.)  Once
270activated, U-boot will show the prompt "FSL DDR>" before enabling the DDR
271controller.  The available commands are printed by typing "help".
272
273Another way to enter the interactive DDR debugger without setting the
274environment variable is to send the 'd' character early during the boot
275process.  To save booting time, no additional delay is added, so the window
276to send the key press is very short -- basically, it is the time before the
277memory controller code starts to run.  For example, when rebooting from
278within u-boot, the user must press 'd' IMMEDIATELY after hitting enter to
279initiate a 'reset' command.  In case of power on/reset, the user can hold
280down the 'd' key while applying power or hitting the board's reset button.
281
282The example flow of using interactive debugging is
283type command "compute" to calculate the parameters from the default
284type command "print" with arguments to show SPD, options, registers
285type command "edit" with arguments to change any if desired
286type command "copy" with arguments to copy controller/dimm settings
287type command "go" to continue calculation and enable DDR controller
288
289Additional commands to restart the debugging are:
290type command "reset" to reset the board
291type command "recompute" to reload SPD and start over
292
293Note, check "next_step" to show the flow. For example, after edit opts, the
294next_step is STEP_ASSIGN_ADDRESSES. After editing registers, the next_step is
295STEP_PROGRAM_REGS.  Upon issuing command "go", the debugger will program the
296DDR controller with the current setting without further calculation and then
297exit to resume the booting of the machine.
298
299The detail syntax for each commands are
300
301print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs]
302	c<n>		- the controller number, eg. c0, c1
303	d<n>		- the DIMM number, eg. d0, d1
304	spd		- print SPD data
305	dimmparms	- DIMM parameters, calculated from SPD
306	commonparms	- lowest common parameters for all DIMMs
307	opts		- options
308	addresses	- address assignment (not implemented yet)
309	regs		- controller registers
310
311edit <c#> <d#> <spd|dimmparms|commonparms|opts|addresses|regs> <element> <value>
312	c<n>		- the controller number, eg. c0, c1
313	d<n>		- the DIMM number, eg. d0, d1
314	spd		- print SPD data
315	dimmparms	- DIMM parameters, calculated from SPD
316	commonparms	- lowest common parameters for all DIMMs
317	opts		- options
318	addresses	- address assignment (not implemented yet)
319	regs		- controller registers
320	<element>	- name of the modified element
321			  byte number if the object is SPD
322	<value>		- decimal or heximal (prefixed with 0x) numbers
323
324copy <src c#> <src d#> <spd|dimmparms|commonparms|opts|addresses|regs> <dst c#> <dst d#>
325	same as for "edit" command
326	DIMM numbers ignored for commonparms, opts, and regs
327
328reset
329	no arguement	- reset the board
330
331recompute
332	no argument	- reload SPD and start over
333
334compute
335	no argument	- recompute from current next_step
336
337next_step
338	no argument	- show current next_step
339
340help
341	no argument	- print a list of all commands
342
343go
344	no argument	- program memory controller(s) and continue with U-boot
345
346Examples of debugging flow
347
348	FSL DDR>compute
349	Detected UDIMM UG51U6400N8SU-ACF
350	FSL DDR>print
351	print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs]
352	FSL DDR>print dimmparms
353	DIMM parameters:  Controller=0 DIMM=0
354	DIMM organization parameters:
355	module part name = UG51U6400N8SU-ACF
356	rank_density = 2147483648 bytes (2048 megabytes)
357	capacity = 4294967296 bytes (4096 megabytes)
358	burst_lengths_bitmask = 0C
359	base_addresss = 0 (00000000 00000000)
360	n_ranks = 2
361	data_width = 64
362	primary_sdram_width = 64
363	ec_sdram_width = 0
364	registered_dimm = 0
365	n_row_addr = 15
366	n_col_addr = 10
367	edc_config = 0
368	n_banks_per_sdram_device = 8
369	tCKmin_X_ps = 1500
370	tCKmin_X_minus_1_ps = 0
371	tCKmin_X_minus_2_ps = 0
372	tCKmax_ps = 0
373	caslat_X = 960
374	tAA_ps = 13125
375	caslat_X_minus_1 = 0
376	caslat_X_minus_2 = 0
377	caslat_lowest_derated = 0
378	tRCD_ps = 13125
379	tRP_ps = 13125
380	tRAS_ps = 36000
381	tWR_ps = 15000
382	tWTR_ps = 7500
383	tRFC_ps = 160000
384	tRRD_ps = 6000
385	tRC_ps = 49125
386	refresh_rate_ps = 7800000
387	tIS_ps = 0
388	tIH_ps = 0
389	tDS_ps = 0
390	tDH_ps = 0
391	tRTP_ps = 7500
392	tDQSQ_max_ps = 0
393	tQHS_ps = 0
394	FSL DDR>edit c0 opts ECC_mode 0
395	FSL DDR>edit c0 regs cs0_bnds 0x000000FF
396	FSL DDR>go
397	2 GiB left unmapped
398	4 GiB (DDR3, 64-bit, CL=9, ECC off)
399	       DDR Chip-Select Interleaving Mode: CS0+CS1
400	Testing 0x00000000 - 0x7fffffff
401	Testing 0x80000000 - 0xffffffff
402	Remap DDR 2 GiB left unmapped
403
404	POST memory PASSED
405	Flash: 128 MiB
406	L2:    128 KB enabled
407	Corenet Platform Cache: 1024 KB enabled
408	SERDES: timeout resetting bank 3
409	SRIO1: disabled
410	SRIO2: disabled
411	MMC:  FSL_ESDHC: 0
412	EEPROM: Invalid ID (ff ff ff ff)
413	PCIe1: disabled
414	PCIe2: Root Complex, x1, regs @ 0xfe201000
415	  01:00.0     - 8086:10d3 - Network controller
416	PCIe2: Bus 00 - 01
417	PCIe3: disabled
418	In:    serial
419	Out:   serial
420	Err:   serial
421	Net:   Initializing Fman
422	Fman1: Uploading microcode version 101.8.0
423	e1000: 00:1b:21:81:d2:e0
424	FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5, e1000#0 [PRIME]
425	Warning: e1000#0 MAC addresses don't match:
426	Address in SROM is         00:1b:21:81:d2:e0
427	Address in environment is  00:e0:0c:00:ea:05
428
429	Hit any key to stop autoboot:  0
430	=>
431