1menu "Boot timing" 2 3config BOOTSTAGE 4 bool "Boot timing and reporting" 5 help 6 Enable recording of boot time while booting. To use it, insert 7 calls to bootstage_mark() with a suitable BOOTSTAGE_ID from 8 bootstage.h. Only a single entry is recorded for each ID. You can 9 give the entry a name with bootstage_mark_name(). You can also 10 record elapsed time in a particular stage using bootstage_start() 11 before starting and bootstage_accum() when finished. Bootstage will 12 add up all the accumulated time and report it. 13 14 Normally, IDs are defined in bootstage.h but a small number of 15 additional 'user' IDs can be used by passing BOOTSTAGE_ID_ALLOC 16 as the ID. 17 18 Calls to show_boot_progress() will also result in log entries but 19 these will not have names. 20 21config SPL_BOOTSTAGE 22 bool "Boot timing and reported in SPL" 23 depends on BOOTSTAGE 24 help 25 Enable recording of boot time in SPL. To make this visible to U-Boot 26 proper, enable BOOTSTAGE_STASH as well. This will stash the timing 27 information when SPL finishes and load it when U-Boot proper starts 28 up. 29 30config BOOTSTAGE_REPORT 31 bool "Display a detailed boot timing report before booting the OS" 32 depends on BOOTSTAGE 33 help 34 Enable output of a boot time report just before the OS is booted. 35 This shows how long it took U-Boot to go through each stage of the 36 boot process. The report looks something like this: 37 38 Timer summary in microseconds: 39 Mark Elapsed Stage 40 0 0 reset 41 3,575,678 3,575,678 board_init_f start 42 3,575,695 17 arch_cpu_init A9 43 3,575,777 82 arch_cpu_init done 44 3,659,598 83,821 board_init_r start 45 3,910,375 250,777 main_loop 46 29,916,167 26,005,792 bootm_start 47 30,361,327 445,160 start_kernel 48 49config BOOTSTAGE_RECORD_COUNT 50 int "Number of boot stage records to store" 51 default 30 52 help 53 This is the size of the bootstage record list and is the maximum 54 number of bootstage records that can be recorded. 55 56config SPL_BOOTSTAGE_RECORD_COUNT 57 int "Number of boot stage records to store for SPL" 58 default 5 59 help 60 This is the size of the bootstage record list and is the maximum 61 number of bootstage records that can be recorded. 62 63config BOOTSTAGE_FDT 64 bool "Store boot timing information in the OS device tree" 65 depends on BOOTSTAGE 66 help 67 Stash the bootstage information in the FDT. A root 'bootstage' 68 node is created with each bootstage id as a child. Each child 69 has a 'name' property and either 'mark' containing the 70 mark time in microseconds, or 'accum' containing the 71 accumulated time for that bootstage id in microseconds. 72 For example: 73 74 bootstage { 75 154 { 76 name = "board_init_f"; 77 mark = <3575678>; 78 }; 79 170 { 80 name = "lcd"; 81 accum = <33482>; 82 }; 83 }; 84 85 Code in the Linux kernel can find this in /proc/devicetree. 86 87config BOOTSTAGE_STASH 88 bool "Stash the boot timing information in memory before booting OS" 89 depends on BOOTSTAGE 90 help 91 Some OSes do not support device tree. Bootstage can instead write 92 the boot timing information in a binary format at a given address. 93 This happens through a call to bootstage_stash(), typically in 94 the CPU's cleanup_before_linux() function. You can use the 95 'bootstage stash' and 'bootstage unstash' commands to do this on 96 the command line. 97 98config BOOTSTAGE_STASH_ADDR 99 hex "Address to stash boot timing information" 100 default 0 101 help 102 Provide an address which will not be overwritten by the OS when it 103 starts, so that it can read this information when ready. 104 105config BOOTSTAGE_STASH_SIZE 106 hex "Size of boot timing stash region" 107 default 0x1000 108 help 109 This should be large enough to hold the bootstage stash. A value of 110 4096 (4KiB) is normally plenty. 111 112endmenu 113 114menu "Boot media" 115 116config NOR_BOOT 117 bool "Support for booting from NOR flash" 118 depends on NOR 119 help 120 Enabling this will make a U-Boot binary that is capable of being 121 booted via NOR. In this case we will enable certain pinmux early 122 as the ROM only partially sets up pinmux. We also default to using 123 NOR for environment. 124 125config NAND_BOOT 126 bool "Support for booting from NAND flash" 127 default n 128 help 129 Enabling this will make a U-Boot binary that is capable of being 130 booted via NAND flash. This is not a must, some SoCs need this, 131 some not. 132 133config ONENAND_BOOT 134 bool "Support for booting from ONENAND" 135 default n 136 help 137 Enabling this will make a U-Boot binary that is capable of being 138 booted via ONENAND. This is not a must, some SoCs need this, 139 some not. 140 141config QSPI_BOOT 142 bool "Support for booting from QSPI flash" 143 default n 144 help 145 Enabling this will make a U-Boot binary that is capable of being 146 booted via QSPI flash. This is not a must, some SoCs need this, 147 some not. 148 149config SATA_BOOT 150 bool "Support for booting from SATA" 151 default n 152 help 153 Enabling this will make a U-Boot binary that is capable of being 154 booted via SATA. This is not a must, some SoCs need this, 155 some not. 156 157config SD_BOOT 158 bool "Support for booting from SD/EMMC" 159 default n 160 help 161 Enabling this will make a U-Boot binary that is capable of being 162 booted via SD/EMMC. This is not a must, some SoCs need this, 163 some not. 164 165config SPI_BOOT 166 bool "Support for booting from SPI flash" 167 default n 168 help 169 Enabling this will make a U-Boot binary that is capable of being 170 booted via SPI flash. This is not a must, some SoCs need this, 171 some not. 172 173endmenu 174 175config BOOTDELAY 176 int "delay in seconds before automatically booting" 177 default 2 178 depends on AUTOBOOT 179 help 180 Delay before automatically running bootcmd; 181 set to 0 to autoboot with no delay, but you can stop it by key input. 182 set to -1 to disable autoboot. 183 set to -2 to autoboot with no delay and not check for abort 184 185 See doc/README.autoboot for details. 186 187config USE_BOOTARGS 188 bool "Enable boot arguments" 189 help 190 Provide boot arguments to bootm command. Boot arguments are specified 191 in CONFIG_BOOTARGS option. Enable this option to be able to specify 192 CONFIG_BOOTARGS string. If this option is disabled, CONFIG_BOOTARGS 193 will be undefined and won't take any space in U-Boot image. 194 195config BOOTARGS 196 string "Boot arguments" 197 depends on USE_BOOTARGS 198 help 199 This can be used to pass arguments to the bootm command. The value of 200 CONFIG_BOOTARGS goes into the environment value "bootargs". Note that 201 this value will also override the "chosen" node in FDT blob. 202 203config USE_BOOTCOMMAND 204 bool "Enable a default value for bootcmd" 205 help 206 Provide a default value for the bootcmd entry in the environment. If 207 autoboot is enabled this is what will be run automatically. Enable 208 this option to be able to specify CONFIG_BOOTCOMMAND as a string. If 209 this option is disabled, CONFIG_BOOTCOMMAND will be undefined and 210 won't take any space in U-Boot image. 211 212config BOOTCOMMAND 213 string "bootcmd value" 214 depends on USE_BOOTCOMMAND 215 default "run distro_bootcmd" if DISTRO_DEFAULTS 216 help 217 This is the string of commands that will be used as bootcmd and if 218 AUTOBOOT is set, automatically run. 219 220menu "Console" 221 222config MENU 223 bool 224 help 225 This is the library functionality to provide a text-based menu of 226 choices for the user to make choices with. 227 228config CONSOLE_RECORD 229 bool "Console recording" 230 help 231 This provides a way to record console output (and provide console 232 input) through circular buffers. This is mostly useful for testing. 233 Console output is recorded even when the console is silent. 234 To enable console recording, call console_record_reset_enable() 235 from your code. 236 237config CONSOLE_RECORD_OUT_SIZE 238 hex "Output buffer size" 239 depends on CONSOLE_RECORD 240 default 0x400 if CONSOLE_RECORD 241 help 242 Set the size of the console output buffer. When this fills up, no 243 more data will be recorded until some is removed. The buffer is 244 allocated immediately after the malloc() region is ready. 245 246config CONSOLE_RECORD_IN_SIZE 247 hex "Input buffer size" 248 depends on CONSOLE_RECORD 249 default 0x100 if CONSOLE_RECORD 250 help 251 Set the size of the console input buffer. When this contains data, 252 tstc() and getc() will use this in preference to real device input. 253 The buffer is allocated immediately after the malloc() region is 254 ready. 255 256config IDENT_STRING 257 string "Board specific string to be added to uboot version string" 258 help 259 This options adds the board specific name to u-boot version. 260 261config LOGLEVEL 262 int "loglevel" 263 default 4 264 range 0 8 265 help 266 All Messages with a loglevel smaller than the console loglevel will 267 be compiled in. The loglevels are defined as follows: 268 269 0 (KERN_EMERG) system is unusable 270 1 (KERN_ALERT) action must be taken immediately 271 2 (KERN_CRIT) critical conditions 272 3 (KERN_ERR) error conditions 273 4 (KERN_WARNING) warning conditions 274 5 (KERN_NOTICE) normal but significant condition 275 6 (KERN_INFO) informational 276 7 (KERN_DEBUG) debug-level messages 277 278config SPL_LOGLEVEL 279 int 280 default LOGLEVEL 281 282config SILENT_CONSOLE 283 bool "Support a silent console" 284 help 285 This option allows the console to be silenced, meaning that no 286 output will appear on the console devices. This is controlled by 287 setting the environment vaariable 'silent' to a non-empty value. 288 Note this also silences the console when booting Linux. 289 290 When the console is set up, the variable is checked, and the 291 GD_FLG_SILENT flag is set. Changing the environment variable later 292 will update the flag. 293 294config SILENT_U_BOOT_ONLY 295 bool "Only silence the U-Boot console" 296 depends on SILENT_CONSOLE 297 help 298 Normally when the U-Boot console is silenced, Linux's console is 299 also silenced (assuming the board boots into Linux). This option 300 allows the linux console to operate normally, even if U-Boot's 301 is silenced. 302 303config SILENT_CONSOLE_UPDATE_ON_SET 304 bool "Changes to the 'silent' environment variable update immediately" 305 depends on SILENT_CONSOLE 306 default y if SILENT_CONSOLE 307 help 308 When the 'silent' environment variable is changed, update the 309 console silence flag immediately. This allows 'setenv' to be used 310 to silence or un-silence the console. 311 312 The effect is that any change to the variable will affect the 313 GD_FLG_SILENT flag. 314 315config SILENT_CONSOLE_UPDATE_ON_RELOC 316 bool "Allow flags to take effect on relocation" 317 depends on SILENT_CONSOLE 318 help 319 In some cases the environment is not available until relocation 320 (e.g. NAND). This option makes the value of the 'silent' 321 environment variable take effect at relocation. 322 323config PRE_CONSOLE_BUFFER 324 bool "Buffer characters before the console is available" 325 help 326 Prior to the console being initialised (i.e. serial UART 327 initialised etc) all console output is silently discarded. 328 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to 329 buffer any console messages prior to the console being 330 initialised to a buffer. The buffer is a circular buffer, so 331 if it overflows, earlier output is discarded. 332 333 Note that this is not currently supported in SPL. It would be 334 useful to be able to share the pre-console buffer with SPL. 335 336config PRE_CON_BUF_SZ 337 int "Sets the size of the pre-console buffer" 338 depends on PRE_CONSOLE_BUFFER 339 default 4096 340 help 341 The size of the pre-console buffer affects how much console output 342 can be held before it overflows and starts discarding earlier 343 output. Normally there is very little output at this early stage, 344 unless debugging is enabled, so allow enough for ~10 lines of 345 text. 346 347 This is a useful feature if you are using a video console and 348 want to see the full boot output on the console. Without this 349 option only the post-relocation output will be displayed. 350 351config PRE_CON_BUF_ADDR 352 hex "Address of the pre-console buffer" 353 depends on PRE_CONSOLE_BUFFER 354 default 0x2f000000 if ARCH_SUNXI && MACH_SUN9I 355 default 0x4f000000 if ARCH_SUNXI && !MACH_SUN9I 356 help 357 This sets the start address of the pre-console buffer. This must 358 be in available memory and is accessed before relocation and 359 possibly before DRAM is set up. Therefore choose an address 360 carefully. 361 362 We should consider removing this option and allocating the memory 363 in board_init_f_init_reserve() instead. 364 365config CONSOLE_MUX 366 bool "Enable console multiplexing" 367 default y if DM_VIDEO || VIDEO || LCD 368 help 369 This allows multiple devices to be used for each console 'file'. 370 For example, stdout can be set to go to serial and video. 371 Similarly, stdin can be set to come from serial and keyboard. 372 Input can be provided from either source. Console multiplexing 373 adds a small amount of size to U-Boot. Changes to the environment 374 variables stdout, stdin and stderr will take effect immediately. 375 376config SYS_CONSOLE_IS_IN_ENV 377 bool "Select console devices from the environment" 378 default y if CONSOLE_MUX 379 help 380 This allows multiple input/output devices to be set at boot time. 381 For example, if stdout is set to "serial,video" then output will 382 be sent to both the serial and video devices on boot. The 383 environment variables can be updated after boot to change the 384 input/output devices. 385 386config SYS_CONSOLE_OVERWRITE_ROUTINE 387 bool "Allow board control over console overwriting" 388 help 389 If this is enabled, and the board-specific function 390 overwrite_console() returns 1, the stdin, stderr and stdout are 391 switched to the serial port, else the settings in the environment 392 are used. If this is not enabled, the console will not be switched 393 to serial. 394 395config SYS_CONSOLE_ENV_OVERWRITE 396 bool "Update environment variables during console init" 397 help 398 The console environment variables (stdout, stdin, stderr) can be 399 used to determine the correct console devices on start-up. This 400 option writes the console devices to these variables on console 401 start-up (after relocation). This causes the environment to be 402 updated to match the console devices actually chosen. 403 404config SYS_CONSOLE_INFO_QUIET 405 bool "Don't display the console devices on boot" 406 help 407 Normally U-Boot displays the current settings for stdout, stdin 408 and stderr on boot when the post-relocation console is set up. 409 Enable this option to supress this output. It can be obtained by 410 calling stdio_print_current_devices() from board code. 411 412config SYS_STDIO_DEREGISTER 413 bool "Allow deregistering stdio devices" 414 default y if USB_KEYBOARD 415 help 416 Generally there is no need to deregister stdio devices since they 417 are never deactivated. But if a stdio device is used which can be 418 removed (for example a USB keyboard) then this option can be 419 enabled to ensure this is handled correctly. 420 421endmenu 422 423menu "Logging" 424 425config LOG 426 bool "Enable logging support" 427 help 428 This enables support for logging of status and debug messages. These 429 can be displayed on the console, recorded in a memory buffer, or 430 discarded if not needed. Logging supports various categories and 431 levels of severity. 432 433config SPL_LOG 434 bool "Enable logging support in SPL" 435 help 436 This enables support for logging of status and debug messages. These 437 can be displayed on the console, recorded in a memory buffer, or 438 discarded if not needed. Logging supports various categories and 439 levels of severity. 440 441config LOG_MAX_LEVEL 442 int "Maximum log level to record" 443 depends on LOG 444 default 5 445 help 446 This selects the maximum log level that will be recorded. Any value 447 higher than this will be ignored. If possible log statements below 448 this level will be discarded at build time. Levels: 449 450 0 - panic 451 1 - critical 452 2 - error 453 3 - warning 454 4 - note 455 5 - info 456 6 - detail 457 7 - debug 458 459config SPL_LOG_MAX_LEVEL 460 int "Maximum log level to record in SPL" 461 depends on SPL_LOG 462 default 3 463 help 464 This selects the maximum log level that will be recorded. Any value 465 higher than this will be ignored. If possible log statements below 466 this level will be discarded at build time. Levels: 467 468 0 - panic 469 1 - critical 470 2 - error 471 3 - warning 472 4 - note 473 5 - info 474 6 - detail 475 7 - debug 476 477config LOG_CONSOLE 478 bool "Allow log output to the console" 479 depends on LOG 480 default y 481 help 482 Enables a log driver which writes log records to the console. 483 Generally the console is the serial port or LCD display. Only the 484 log message is shown - other details like level, category, file and 485 line number are omitted. 486 487config LOG_SPL_CONSOLE 488 bool "Allow log output to the console in SPL" 489 depends on LOG_SPL 490 default y 491 help 492 Enables a log driver which writes log records to the console. 493 Generally the console is the serial port or LCD display. Only the 494 log message is shown - other details like level, category, file and 495 line number are omitted. 496 497config LOG_TEST 498 bool "Provide a test for logging" 499 depends on LOG 500 default y if SANDBOX 501 help 502 This enables a 'log test' command to test logging. It is normally 503 executed from a pytest and simply outputs logging information 504 in various different ways to test that the logging system works 505 correctly with varoius settings. 506 507endmenu 508 509config DEFAULT_FDT_FILE 510 string "Default fdt file" 511 help 512 This option is used to set the default fdt file to boot OS. 513 514config VERSION_VARIABLE 515 bool "add U-Boot environment variable vers" 516 default n 517 help 518 If this variable is defined, an environment variable 519 named "ver" is created by U-Boot showing the U-Boot 520 version as printed by the "version" command. 521 Any change to this variable will be reverted at the 522 next reset. 523 524config BOARD_LATE_INIT 525 bool 526 help 527 Sometimes board require some initialization code that might 528 require once the actual init done, example saving board specific env, 529 boot-modes etc. which eventually done at late. 530 531 So this config enable the late init code with the help of board_late_init 532 function which should defined on respective boards. 533 534config DISPLAY_CPUINFO 535 bool "Display information about the CPU during start up" 536 default y if ARM || NIOS2 || X86 || XTENSA || M68K 537 help 538 Display information about the CPU that U-Boot is running on 539 when U-Boot starts up. The function print_cpuinfo() is called 540 to do this. 541 542config DISPLAY_BOARDINFO 543 bool "Display information about the board during start up" 544 default y if ARM || M68K || MIPS || PPC || SANDBOX || XTENSA 545 help 546 Display information about the board that U-Boot is running on 547 when U-Boot starts up. The board function checkboard() is called 548 to do this. 549 550menu "Start-up hooks" 551 552config ARCH_EARLY_INIT_R 553 bool "Call arch-specific init soon after relocation" 554 help 555 With this option U-Boot will call arch_early_init_r() soon after 556 relocation. Driver model is running by this point, and the cache 557 is on. Note that board_early_init_r() is called first, if 558 enabled. This can be used to set up architecture-specific devices. 559 560config ARCH_MISC_INIT 561 bool "Call arch-specific init after relocation, when console is ready" 562 help 563 With this option U-Boot will call arch_misc_init() after 564 relocation to allow miscellaneous arch-dependent initialisation 565 to be performed. This function should be defined by the board 566 and will be called after the console is set up, after relocaiton. 567 568config BOARD_EARLY_INIT_F 569 bool "Call board-specific init before relocation" 570 help 571 Some boards need to perform initialisation as soon as possible 572 after boot. With this option, U-Boot calls board_early_init_f() 573 after driver model is ready in the pre-relocation init sequence. 574 Note that the normal serial console is not yet set up, but the 575 debug UART will be available if enabled. 576 577endmenu 578 579menu "Security support" 580 581config HASH 582 bool # "Support hashing API (SHA1, SHA256, etc.)" 583 help 584 This provides a way to hash data in memory using various supported 585 algorithms (such as SHA1, MD5, CRC32). The API is defined in hash.h 586 and the algorithms it supports are defined in common/hash.c. See 587 also CMD_HASH for command-line access. 588 589endmenu 590 591source "common/spl/Kconfig" 592