xref: /openbmc/u-boot/cmd/Kconfig (revision a674313c)
1menu "Command line interface"
2
3config CMDLINE
4	bool "Support U-Boot commands"
5	default y
6	help
7	  Enable U-Boot's command-line functions. This provides a means
8	  to enter commands into U-Boot for a wide variety of purposes. It
9	  also allows scripts (containing commands) to be executed.
10	  Various commands and command categorys can be indivdually enabled.
11	  Depending on the number of commands enabled, this can add
12	  substantially to the size of U-Boot.
13
14config HUSH_PARSER
15	bool "Use hush shell"
16	depends on CMDLINE
17	help
18	  This option enables the "hush" shell (from Busybox) as command line
19	  interpreter, thus enabling powerful command line syntax like
20	  if...then...else...fi conditionals or `&&' and '||'
21	  constructs ("shell scripts").
22
23	  If disabled, you get the old, much simpler behaviour with a somewhat
24	  smaller memory footprint.
25
26config CMDLINE_EDITING
27	bool "Enable command line editing"
28	depends on CMDLINE
29	default y
30	help
31	  Enable editing and History functions for interactive command line
32	  input operations
33
34config AUTO_COMPLETE
35	bool "Enable auto complete using TAB"
36	depends on CMDLINE
37	default y
38	help
39	  Enable auto completion of commands using TAB.
40
41config SYS_LONGHELP
42	bool "Enable long help messages"
43	depends on CMDLINE
44	default y if CMDLINE
45	help
46	  Defined when you want long help messages included
47	  Do not set this option when short of memory.
48
49config SYS_PROMPT
50	string "Shell prompt"
51	default "=> "
52	help
53	  This string is displayed in the command line to the left of the
54	  cursor.
55
56menu "Autoboot options"
57
58config AUTOBOOT
59	bool "Autoboot"
60	default y
61	help
62	  This enables the autoboot.  See doc/README.autoboot for detail.
63
64config AUTOBOOT_KEYED
65	bool "Stop autobooting via specific input key / string"
66	default n
67	help
68	  This option enables stopping (aborting) of the automatic
69	  boot feature only by issuing a specific input key or
70	  string. If not enabled, any input key will abort the
71	  U-Boot automatic booting process and bring the device
72	  to the U-Boot prompt for user input.
73
74config AUTOBOOT_PROMPT
75	string "Autoboot stop prompt"
76	depends on AUTOBOOT_KEYED
77	default "Autoboot in %d seconds\\n"
78	help
79	  This string is displayed before the boot delay selected by
80	  CONFIG_BOOTDELAY starts. If it is not defined	there is no
81	  output indicating that autoboot is in progress.
82
83	  Note that this define is used as the (only) argument to a
84	  printf() call, so it may contain '%' format specifications,
85	  provided that it also includes, sepearated by commas exactly
86	  like in a printf statement, the required arguments. It is
87	  the responsibility of the user to select only such arguments
88	  that are valid in the given context.
89
90config AUTOBOOT_ENCRYPTION
91	bool "Enable encryption in autoboot stopping"
92	depends on AUTOBOOT_KEYED
93	default n
94
95config AUTOBOOT_DELAY_STR
96	string "Delay autobooting via specific input key / string"
97	depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION
98	help
99	  This option delays the automatic boot feature by issuing
100	  a specific input key or string. If CONFIG_AUTOBOOT_DELAY_STR
101	  or the environment variable "bootdelaykey" is specified
102	  and this string is received from console input before
103	  autoboot starts booting, U-Boot gives a command prompt. The
104	  U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is
105	  used, otherwise it never times out.
106
107config AUTOBOOT_STOP_STR
108	string "Stop autobooting via specific input key / string"
109	depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION
110	help
111	  This option enables stopping (aborting) of the automatic
112	  boot feature only by issuing a specific input key or
113	  string. If CONFIG_AUTOBOOT_STOP_STR or the environment
114	  variable "bootstopkey" is specified and this string is
115	  received from console input before autoboot starts booting,
116	  U-Boot gives a command prompt. The U-Boot prompt never
117	  times out, even if CONFIG_BOOT_RETRY_TIME is used.
118
119config AUTOBOOT_KEYED_CTRLC
120	bool "Enable Ctrl-C autoboot interruption"
121	depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION
122	default n
123	help
124	  This option allows for the boot sequence to be interrupted
125	  by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey".
126	  Setting this variable	provides an escape sequence from the
127	  limited "password" strings.
128
129config AUTOBOOT_STOP_STR_SHA256
130	string "Stop autobooting via SHA256 encrypted password"
131	depends on AUTOBOOT_KEYED && AUTOBOOT_ENCRYPTION
132	help
133	  This option adds the feature to only stop the autobooting,
134	  and therefore boot into the U-Boot prompt, when the input
135	  string / password matches a values that is encypted via
136	  a SHA256 hash and saved in the environment.
137
138endmenu
139
140config BUILD_BIN2C
141	bool
142
143comment "Commands"
144
145menu "Info commands"
146
147config CMD_BDI
148	bool "bdinfo"
149	default y
150	help
151	  Print board info
152
153config CMD_CONFIG
154	bool "config"
155	select BUILD_BIN2C
156	default SANDBOX
157	help
158	  Print ".config" contents.
159
160	  If this option is enabled, the ".config" file contents are embedded
161	  in the U-Boot image and can be printed on the console by the "config"
162	  command.  This provides information of which options are enabled on
163	  the running U-Boot.
164
165config CMD_CONSOLE
166	bool "coninfo"
167	default y
168	help
169	  Print console devices and information.
170
171config CMD_CPU
172	bool "cpu"
173	help
174	  Print information about available CPUs. This normally shows the
175	  number of CPUs, type (e.g. manufacturer, architecture, product or
176	  internal name) and clock frequency. Other information may be
177	  available depending on the CPU driver.
178
179config CMD_LICENSE
180	bool "license"
181	select BUILD_BIN2C
182	help
183	  Print GPL license text
184
185config CMD_REGINFO
186	bool "reginfo"
187	depends on PPC
188	help
189	  Register dump
190
191endmenu
192
193menu "Boot commands"
194
195config CMD_BOOTD
196	bool "bootd"
197	default y
198	help
199	  Run the command stored in the environment "bootcmd", i.e.
200	  "bootd" does the same thing as "run bootcmd".
201
202config CMD_BOOTM
203	bool "bootm"
204	default y
205	help
206	  Boot an application image from the memory.
207
208config CMD_BOOTZ
209	bool "bootz"
210	help
211	  Boot the Linux zImage
212
213config CMD_BOOTI
214	bool "booti"
215	depends on ARM64
216	default y
217	help
218	  Boot an AArch64 Linux Kernel image from memory.
219
220config CMD_BOOTEFI
221	bool "bootefi"
222	depends on EFI_LOADER
223	default y
224	help
225	  Boot an EFI image from memory.
226
227config CMD_BOOTEFI_HELLO_COMPILE
228	bool "Compile a standard EFI hello world binary for testing"
229	depends on CMD_BOOTEFI && (ARM || X86 || RISCV)
230	default y
231	help
232	  This compiles a standard EFI hello world application with U-Boot so
233	  that it can be used with the test/py testing framework. This is useful
234	  for testing that EFI is working at a basic level, and for bringing
235	  up EFI support on a new architecture.
236
237	  No additional space will be required in the resulting U-Boot binary
238	  when this option is enabled.
239
240config CMD_BOOTEFI_HELLO
241	bool "Allow booting a standard EFI hello world for testing"
242	depends on CMD_BOOTEFI_HELLO_COMPILE
243	help
244	  This adds a standard EFI hello world application to U-Boot so that
245	  it can be used with the 'bootefi hello' command. This is useful
246	  for testing that EFI is working at a basic level, and for bringing
247	  up EFI support on a new architecture.
248
249source lib/efi_selftest/Kconfig
250
251config CMD_BOOTMENU
252	bool "bootmenu"
253	select MENU
254	help
255	  Add an ANSI terminal boot menu command.
256
257config CMD_ELF
258	bool "bootelf, bootvx"
259	default y
260	help
261	  Boot an ELF/vxWorks image from the memory.
262
263config CMD_FDT
264	bool "Flattened Device Tree utility commands"
265	default y
266	depends on OF_LIBFDT
267	help
268	  Do FDT related setup before booting into the Operating System.
269
270config CMD_GO
271	bool "go"
272	default y
273	help
274	  Start an application at a given address.
275
276config CMD_RUN
277	bool "run"
278	default y
279	help
280	  Run the command in the given environment variable.
281
282config CMD_IMI
283	bool "iminfo"
284	default y
285	help
286	  Print header information for application image.
287
288config CMD_IMLS
289	bool "imls"
290	help
291	  List all images found in flash
292
293config CMD_XIMG
294	bool "imxtract"
295	default y
296	help
297	  Extract a part of a multi-image.
298
299config CMD_POWEROFF
300	bool "poweroff"
301	help
302	  Poweroff/Shutdown the system
303
304config CMD_SPL
305	bool "spl export - Export boot information for Falcon boot"
306	depends on SPL
307	help
308	  Falcon mode allows booting directly from SPL into an Operating
309	  System such as Linux, thus skipping U-Boot proper. See
310	  doc/README.falcon for full information about how to use this
311	  command.
312
313config CMD_SPL_NAND_OFS
314	hex "Offset of OS command line args for Falcon-mode NAND boot"
315	depends on CMD_SPL
316	default 0
317	help
318	  This provides the offset of the command line arguments for Linux
319	  when booting from NAND in Falcon mode.  See doc/README.falcon
320	  for full information about how to use this option (and also see
321	  board/gateworks/gw_ventana/README for an example).
322
323config CMD_SPL_WRITE_SIZE
324	hex "Size of argument area"
325	depends on CMD_SPL
326	default 0x2000
327	help
328	  This provides the size of the command-line argument area in NAND
329	  flash used by Falcon-mode boot. See the documentation until CMD_SPL
330	  for detail.
331
332config CMD_FITUPD
333	bool "fitImage update command"
334	help
335	  Implements the 'fitupd' command, which allows to automatically
336	  store software updates present on a TFTP server in NOR Flash
337
338config CMD_THOR_DOWNLOAD
339	bool "thor - TIZEN 'thor' download"
340	help
341	  Implements the 'thor' download protocol. This is a way of
342	  downloading a software update over USB from an attached host.
343	  There is no documentation about this within the U-Boot source code
344	  but you should be able to find something on the interwebs.
345
346config CMD_ZBOOT
347	bool "zboot - x86 boot command"
348	help
349	  With x86 machines it is common to boot a bzImage file which
350	  contains both a kernel and a setup.bin file. The latter includes
351	  configuration information from the dark ages which x86 boards still
352	  need to pick things out of.
353
354	  Consider using FIT in preference to this since it supports directly
355	  booting both 32- and 64-bit kernels, as well as secure boot.
356	  Documentation is available in doc/uImage.FIT/x86-fit-boot.txt
357
358endmenu
359
360menu "Environment commands"
361
362config CMD_ASKENV
363	bool "ask for env variable"
364	help
365	  Ask for environment variable
366
367config CMD_EXPORTENV
368	bool "env export"
369	default y
370	help
371	  Export environments.
372
373config CMD_IMPORTENV
374	bool "env import"
375	default y
376	help
377	  Import environments.
378
379config CMD_EDITENV
380	bool "editenv"
381	default y
382	help
383	  Edit environment variable.
384
385config CMD_GREPENV
386	bool "search env"
387	help
388	  Allow for searching environment variables
389
390config CMD_SAVEENV
391	bool "saveenv"
392	default y
393	help
394	  Save all environment variables into the compiled-in persistent
395	  storage.
396
397config CMD_ENV_EXISTS
398	bool "env exists"
399	default y
400	help
401	  Check if a variable is defined in the environment for use in
402	  shell scripting.
403
404config CMD_ENV_CALLBACK
405	bool "env callbacks - print callbacks and their associated variables"
406	help
407	  Some environment variable have callbacks defined by
408	  U_BOOT_ENV_CALLBACK. These are called when the variable changes.
409	  For example changing "baudrate" adjust the serial baud rate. This
410	  command lists the currently defined callbacks.
411
412config CMD_ENV_FLAGS
413	bool "env flags -print variables that have non-default flags"
414	help
415	  Some environment variables have special flags that control their
416	  behaviour. For example, serial# can only be written once and cannot
417	  be deleted. This command shows the variables that have special
418	  flags.
419
420endmenu
421
422menu "Memory commands"
423
424config CMD_BINOP
425	bool "binop"
426	help
427	  Compute binary operations (xor, or, and) of byte arrays of arbitrary
428	  size from memory and store the result in memory or the environment.
429
430config CMD_CRC32
431	bool "crc32"
432	select HASH
433	default y
434	help
435	  Compute CRC32.
436
437config CRC32_VERIFY
438	bool "crc32 -v"
439	depends on CMD_CRC32
440	help
441	  Add -v option to verify data against a crc32 checksum.
442
443config CMD_EEPROM
444	bool "eeprom - EEPROM subsystem"
445	help
446	  (deprecated, needs conversion to driver model)
447	  Provides commands to read and write EEPROM (Electrically Erasable
448	  Programmable Read Only Memory) chips that are connected over an
449	  I2C bus.
450
451config CMD_EEPROM_LAYOUT
452	bool "Enable layout-aware eeprom commands"
453	depends on CMD_EEPROM
454	help
455	  (deprecated, needs conversion to driver model)
456	  When enabled, additional eeprom sub-commands become available.
457
458	  eeprom print - prints the contents of the eeprom in a human-readable
459	  way (eeprom layout fields, and data formatted to be fit for human
460	  consumption).
461
462	  eeprom update - allows user to update eeprom fields by specifying
463	  the field name, and providing the new data in a human readable format
464	  (same format as displayed by the eeprom print command).
465
466	  Both commands can either auto detect the layout, or be told which
467	  layout to use.
468
469	  Feature API:
470	  __weak int parse_layout_version(char *str)
471		- override to provide your own layout name parsing
472	  __weak void __eeprom_layout_assign(struct eeprom_layout *layout,
473			int layout_version);
474		- override to setup the layout metadata based on the version
475	  __weak int eeprom_layout_detect(unsigned char *data)
476		- override to provide your own algorithm for detecting layout
477			version
478	  eeprom_field.c
479		- contains various printing and updating functions for common
480			types of eeprom fields. Can be used for defining
481			custom layouts.
482
483config EEPROM_LAYOUT_HELP_STRING
484	  string "Tells user what layout names are supported"
485	  depends on CMD_EEPROM_LAYOUT
486	  default "<not defined>"
487	  help
488	    Help printed with the LAYOUT VERSIONS part of the 'eeprom'
489	    command's help.
490
491config LOOPW
492	bool "loopw"
493	help
494	  Infinite write loop on address range
495
496config CMD_MD5SUM
497	bool "md5sum"
498	default n
499	select MD5
500	help
501	  Compute MD5 checksum.
502
503config MD5SUM_VERIFY
504	bool "md5sum -v"
505	default n
506	depends on CMD_MD5SUM
507	help
508	  Add -v option to verify data against an MD5 checksum.
509
510config CMD_MEMINFO
511	bool "meminfo"
512	help
513	  Display memory information.
514
515config CMD_MEMORY
516	bool "md, mm, nm, mw, cp, cmp, base, loop"
517	default y
518	help
519	  Memory commands.
520	    md - memory display
521	    mm - memory modify (auto-incrementing address)
522	    nm - memory modify (constant address)
523	    mw - memory write (fill)
524	    cp - memory copy
525	    cmp - memory compare
526	    base - print or set address offset
527	    loop - initialize loop on address range
528
529config CMD_MEMTEST
530	bool "memtest"
531	help
532	  Simple RAM read/write test.
533
534if CMD_MEMTEST
535
536config SYS_ALT_MEMTEST
537	bool "Alternative test"
538	help
539	  Use a more complete alternative memory test.
540
541endif
542
543config CMD_MX_CYCLIC
544	bool "mdc, mwc"
545	help
546	  mdc - memory display cyclic
547	  mwc - memory write cyclic
548
549config CMD_SHA1SUM
550	bool "sha1sum"
551	select SHA1
552	help
553	  Compute SHA1 checksum.
554
555config SHA1SUM_VERIFY
556	bool "sha1sum -v"
557	depends on CMD_SHA1SUM
558	help
559	  Add -v option to verify data against a SHA1 checksum.
560
561config CMD_STRINGS
562	bool "strings - display strings in memory"
563	help
564	  This works similarly to the Unix 'strings' command except that it
565	  works with a memory range. String of printable characters found
566	  within the range are displayed. The minimum number of characters
567	  for a sequence to be considered a string can be provided.
568
569endmenu
570
571menu "Compression commands"
572
573config CMD_LZMADEC
574	bool "lzmadec"
575	default y if CMD_BOOTI
576	select LZMA
577	help
578	  Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm)
579	  image from memory.
580
581config CMD_UNZIP
582	bool "unzip"
583	default y if CMD_BOOTI
584	help
585	  Uncompress a zip-compressed memory region.
586
587config CMD_ZIP
588	bool "zip"
589	help
590	  Compress a memory region with zlib deflate method.
591
592endmenu
593
594menu "Device access commands"
595
596config CMD_ARMFLASH
597	#depends on FLASH_CFI_DRIVER
598	bool "armflash"
599	help
600	  ARM Ltd reference designs flash partition access
601
602config CMD_ADC
603	bool "adc - Access Analog to Digital Converters info and data"
604	select ADC
605	select DM_REGULATOR
606	help
607	  Shows ADC device info and permit printing one-shot analog converted
608	  data from a named Analog to Digital Converter.
609
610config CMD_CLK
611	bool "clk - Show clock frequencies"
612	help
613	  (deprecated)
614	  Shows clock frequences by calling a sock_clk_dump() hook function.
615	  This is depreated in favour of using the CLK uclass and accessing
616	  clock values from associated drivers. However currently no command
617	  exists for this.
618
619config CMD_DEMO
620	bool "demo - Demonstration commands for driver model"
621	depends on DM
622	help
623	  Provides a 'demo' command which can be used to play around with
624	  driver model. To use this properly you will need to enable one or
625	  both of the demo devices (DM_DEMO_SHAPE and DM_DEMO_SIMPLE).
626	  Otherwise you will always get an empty list of devices. The demo
627	  devices are defined in the sandbox device tree, so the easiest
628	  option is to use sandbox and pass the -d point to sandbox's
629	  u-boot.dtb file.
630
631config CMD_DFU
632	bool "dfu"
633	select DFU
634	help
635	  Enables the command "dfu" which is used to have U-Boot create a DFU
636	  class device via USB. This command requires that the "dfu_alt_info"
637	  environment variable be set and define the alt settings to expose to
638	  the host.
639
640config CMD_DM
641	bool "dm - Access to driver model information"
642	depends on DM
643	default y
644	help
645	  Provides access to driver model data structures and information,
646	  such as a list of devices, list of uclasses and the state of each
647	  device (e.g. activated). This is not required for operation, but
648	  can be useful to see the state of driver model for debugging or
649	  interest.
650
651config CMD_FASTBOOT
652	bool "fastboot - Android fastboot support"
653	depends on FASTBOOT
654	help
655	  This enables the command "fastboot" which enables the Android
656	  fastboot mode for the platform. Fastboot is a protocol for
657	  downloading images, flashing and device control used on
658	  Android devices. Fastboot requires either the network stack
659	  enabled or support for acting as a USB device.
660
661	  See doc/README.android-fastboot for more information.
662
663config CMD_FDC
664	bool "fdcboot - Boot from floppy device"
665	help
666	  The 'fdtboot' command allows booting an image from a floppy disk.
667
668config CMD_FLASH
669	bool "flinfo, erase, protect"
670	default y
671	help
672	  NOR flash support.
673	    flinfo - print FLASH memory information
674	    erase - FLASH memory
675	    protect - enable or disable FLASH write protection
676
677config CMD_FPGA
678	bool "fpga"
679	depends on FPGA
680	default y
681	help
682	  FPGA support.
683
684config CMD_FPGA_LOADBP
685	bool "fpga loadbp - load partial bitstream (Xilinx only)"
686	depends on CMD_FPGA
687	help
688	  Supports loading an FPGA device from a bitstream buffer containing
689	  a partial bitstream.
690
691config CMD_FPGA_LOADFS
692	bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)"
693	depends on CMD_FPGA
694	help
695	  Supports loading an FPGA device from a FAT filesystem.
696
697config CMD_FPGA_LOADMK
698	bool "fpga loadmk - load bitstream from image"
699	depends on CMD_FPGA
700	help
701	  Supports loading an FPGA device from a image generated by mkimage.
702
703config CMD_FPGA_LOADP
704	bool "fpga loadp - load partial bitstream"
705	depends on CMD_FPGA
706	help
707	  Supports loading an FPGA device from a bitstream buffer containing
708	  a partial bitstream.
709
710config CMD_FPGA_LOAD_SECURE
711	bool "fpga loads - loads secure bitstreams (Xilinx only)"
712	depends on CMD_FPGA
713	help
714	  Enables the fpga loads command which is used to load secure
715	  (authenticated or encrypted or both) bitstreams on to FPGA.
716
717config CMD_FPGAD
718	bool "fpgad - dump FPGA registers"
719	help
720	  (legacy, needs conversion to driver model)
721	  Provides a way to dump FPGA registers by calling the board-specific
722	  fpga_get_reg() function. This functions similarly to the 'md'
723	  command.
724
725config CMD_FUSE
726	bool "fuse - support for the fuse subssystem"
727	help
728	  (deprecated - needs conversion to driver model)
729	  This allows reading, sensing, programming or overriding fuses
730	  which control the behaviour of the device. The command uses the
731	  fuse_...() API.
732
733config CMD_GPIO
734	bool "gpio"
735	help
736	  GPIO support.
737
738config CMD_GPT
739	bool "GPT (GUID Partition Table) command"
740	select PARTITION_UUIDS
741	select EFI_PARTITION
742	select HAVE_BLOCK_DEVICE
743	imply RANDOM_UUID
744	help
745	  Enable the 'gpt' command to ready and write GPT style partition
746	  tables.
747
748config RANDOM_UUID
749	bool "GPT Random UUID generation"
750	select LIB_UUID
751	help
752	  Enable the generation of partitions with random UUIDs if none
753	  are provided.
754
755config CMD_GPT_RENAME
756	bool "GPT partition renaming commands"
757	depends on CMD_GPT
758	help
759	  Enables the 'gpt' command to interchange names on two GPT
760	  partitions via the 'gpt swap' command or to rename single
761	  partitions via the 'rename' command.
762
763config CMD_IDE
764	bool "ide - Support for IDE drivers"
765	select IDE
766	help
767	  Provides an 'ide' command which allows accessing the IDE drive,
768	  reseting the IDE interface, printing the partition table and
769	  geting device info. It also enables the 'diskboot' command which
770	  permits booting from an IDE drive.
771
772config CMD_IO
773	bool "io - Support for performing I/O accesses"
774	help
775	  Provides an 'iod' command to display I/O space and an 'iow' command
776	  to write values to the I/O space. This can be useful for manually
777	  checking the state of devices during boot when debugging device
778	  drivers, etc.
779
780config CMD_IOTRACE
781	bool "iotrace - Support for tracing I/O activity"
782	help
783	  Provides an 'iotrace' command which supports recording I/O reads and
784	  writes in a trace buffer in memory . It also maintains a checksum
785	  of the trace records (even if space is exhausted) so that the
786	  sequence of I/O accesses can be verified.
787
788	  When debugging drivers it is useful to see what I/O accesses were
789	  done and in what order.
790
791	  Even if the individual accesses are of little interest it can be
792	  useful to verify that the access pattern is consistent each time
793	  an operation is performed. In this case a checksum can be used to
794	  characterise the operation of a driver. The checksum can be compared
795	  across different runs of the operation to verify that the driver is
796	  working properly.
797
798	  In particular, when performing major refactoring of the driver, where
799	  the access pattern should not change, the checksum provides assurance
800	  that the refactoring work has not broken the driver.
801
802	  This works by sneaking into the io.h heder for an architecture and
803	  redirecting I/O accesses through iotrace's tracing mechanism.
804
805	  For now no commands are provided to examine the trace buffer. The
806	  format is fairly simple, so 'md' is a reasonable substitute.
807
808	  Note: The checksum feature is only useful for I/O regions where the
809	  contents do not change outside of software control. Where this is not
810	  suitable you can fall back to manually comparing the addresses. It
811	  might be useful to enhance tracing to only checksum the accesses and
812	  not the data read/written.
813
814config CMD_I2C
815	bool "i2c"
816	help
817	  I2C support.
818
819config CMD_LOADB
820	bool "loadb"
821	default y
822	help
823	  Load a binary file over serial line.
824
825config CMD_LOADS
826	bool "loads"
827	default y
828	help
829	  Load an S-Record file over serial line
830
831config CMD_MMC
832	bool "mmc"
833	help
834	  MMC memory mapped support.
835
836config CMD_MMC_RPMB
837	bool "Enable support for RPMB in the mmc command"
838	depends on CMD_MMC
839	help
840	  Enable the commands for reading, writing and programming the
841	  key for the Replay Protection Memory Block partition in eMMC.
842
843config CMD_MMC_SWRITE
844	bool "mmc swrite"
845	depends on CMD_MMC && MMC_WRITE
846	select IMAGE_SPARSE
847	help
848	  Enable support for the "mmc swrite" command to write Android sparse
849	  images to eMMC.
850
851config CMD_NAND
852	bool "nand"
853	default y if NAND_SUNXI
854	help
855	  NAND support.
856
857if CMD_NAND
858config CMD_NAND_TRIMFFS
859	bool "nand write.trimffs"
860	default y if ARCH_SUNXI
861	help
862	  Allows one to skip empty pages when flashing something on a NAND.
863
864config CMD_NAND_LOCK_UNLOCK
865	bool "nand lock/unlock"
866	help
867	  NAND locking support.
868
869config CMD_NAND_TORTURE
870	bool "nand torture"
871	help
872	  NAND torture support.
873
874endif # CMD_NAND
875
876config CMD_NVME
877	bool "nvme"
878	depends on NVME
879	default y if NVME
880	help
881	  NVM Express device support
882
883config CMD_MMC_SPI
884	bool "mmc_spi - Set up MMC SPI device"
885	help
886	  Provides a way to set up an MMC (Multimedia Card) SPI (Serial
887	  Peripheral Interface) device. The device provides a means of
888	  accessing an MMC device via SPI using a single data line, limited
889	  to 20MHz. It is useful since it reduces the amount of protocol code
890	  required.
891
892config CMD_ONENAND
893	bool "onenand - access to onenand device"
894	help
895	  OneNAND is a brand of NAND ('Not AND' gate) flash which provides
896	  various useful features. This command allows reading, writing,
897	  and erasing blocks. It allso provides a way to show and change
898	  bad blocks, and test the device.
899
900config CMD_PART
901	bool "part"
902	select PARTITION_UUIDS
903	select HAVE_BLOCK_DEVICE
904	help
905	  Read and display information about the partition table on
906	  various media.
907
908config CMD_PCI
909	bool "pci - Access PCI devices"
910	help
911	  Provide access to PCI (Peripheral Interconnect Bus), a type of bus
912	  used on some devices to allow the CPU to communicate with its
913	  peripherals. Sub-commands allow bus enumeration, displaying and
914	  changing configuration space and a few other features.
915
916config CMD_PCMCIA
917	bool "pinit - Set up PCMCIA device"
918	help
919	  Provides a means to initialise a PCMCIA (Personal Computer Memory
920	  Card International Association) device. This is an old standard from
921	  about 1990. These devices are typically removable memory or network
922	  cards using a standard 68-pin connector.
923
924config CMD_READ
925	bool "read - Read binary data from a partition"
926	help
927	  Provides low-level access to the data in a partition.
928
929config CMD_REMOTEPROC
930	bool "remoteproc"
931	depends on REMOTEPROC
932	help
933	  Support for Remote Processor control
934
935config CMD_SATA
936	bool "sata - Access SATA subsystem"
937	select SATA
938	help
939	  SATA (Serial Advanced Technology Attachment) is a serial bus
940	  standard for connecting to hard drives and other storage devices.
941	  This command provides information about attached devices and allows
942	  reading, writing and other operations.
943
944	  SATA replaces PATA (originally just ATA), which stands for Parallel AT
945	  Attachment, where AT refers to an IBM AT (Advanced Technology)
946	  computer released in 1984.
947
948config CMD_SAVES
949	bool "saves - Save a file over serial in S-Record format"
950	help
951	  Provides a way to save a binary file using the Motorola S-Record
952	  format over the serial line.
953
954config CMD_SCSI
955	bool "scsi - Access to SCSI devices"
956	default y if SCSI
957	help
958	  This provides a 'scsi' command which provides access to SCSI (Small
959	  Computer System Interface) devices. The command provides a way to
960	  scan the bus, reset the bus, read and write data and get information
961	  about devices.
962
963config CMD_SDRAM
964	bool "sdram - Print SDRAM configuration information"
965	help
966	  Provides information about attached SDRAM. This assumed that the
967	  SDRAM has an EEPROM with information that can be read using the
968	  I2C bus. This is only available on some boards.
969
970config CMD_SF
971	bool "sf"
972	help
973	  SPI Flash support
974
975config CMD_SF_TEST
976	bool "sf test - Allow testing of SPI flash"
977	help
978	  Provides a way to test that SPI flash is working correctly. The
979	  test is destructive, in that an area of SPI flash must be provided
980	  for the test to use. Performance information is also provided,
981	  measuring the performance of reading, writing and erasing in
982	  Mbps (Million Bits Per Second). This value should approximately
983	  equal the SPI bus speed for a single-bit-wide SPI bus, assuming
984	  everything is working properly.
985
986config CMD_SPI
987	bool "sspi"
988	help
989	  SPI utility command.
990
991config CMD_TSI148
992	bool "tsi148 - Command to access tsi148 device"
993	help
994	  This provides various sub-commands to initialise and configure the
995	  Turndra tsi148 device. See the command help for full details.
996
997config CMD_UNIVERSE
998	bool "universe - Command to set up the Turndra Universe controller"
999	help
1000	  This allows setting up the VMEbus provided by this controller.
1001	  See the command help for full details.
1002
1003config CMD_USB
1004	bool "usb"
1005	select HAVE_BLOCK_DEVICE
1006	help
1007	  USB support.
1008
1009config CMD_USB_SDP
1010	bool "sdp"
1011	select USB_FUNCTION_SDP
1012	help
1013	  Enables the command "sdp" which is used to have U-Boot emulating the
1014	  Serial Download Protocol (SDP) via USB.
1015config CMD_ROCKUSB
1016	bool "rockusb"
1017	depends on USB_FUNCTION_ROCKUSB
1018	help
1019          Rockusb protocol is widely used by Rockchip SoC based devices. It can
1020	  read/write info, image to/from devices. This enable rockusb command
1021	  support to communication with rockusb device. for more detail about
1022	  this command, please read doc/README.rockusb.
1023
1024config CMD_USB_MASS_STORAGE
1025	bool "UMS usb mass storage"
1026	select USB_FUNCTION_MASS_STORAGE
1027	help
1028	  USB mass storage support
1029
1030endmenu
1031
1032
1033menu "Shell scripting commands"
1034
1035config CMD_ECHO
1036	bool "echo"
1037	default y
1038	help
1039	  Echo args to console
1040
1041config CMD_ITEST
1042	bool "itest"
1043	default y
1044	help
1045	  Return true/false on integer compare.
1046
1047config CMD_SOURCE
1048	bool "source"
1049	default y
1050	help
1051	  Run script from memory
1052
1053config CMD_SETEXPR
1054	bool "setexpr"
1055	default y
1056	help
1057	  Evaluate boolean and math expressions and store the result in an env
1058	    variable.
1059	  Also supports loading the value at a memory location into a variable.
1060	  If CONFIG_REGEX is enabled, setexpr also supports a gsub function.
1061
1062endmenu
1063
1064if NET
1065
1066menuconfig CMD_NET
1067	bool "Network commands"
1068	default y
1069
1070if CMD_NET
1071
1072config CMD_BOOTP
1073	bool "bootp"
1074	default y
1075	help
1076	  bootp - boot image via network using BOOTP/TFTP protocol
1077
1078config CMD_DHCP
1079	bool "dhcp"
1080	depends on CMD_BOOTP
1081	help
1082	  Boot image via network using DHCP/TFTP protocol
1083
1084config BOOTP_BOOTPATH
1085	bool "Request & store 'rootpath' from BOOTP/DHCP server"
1086	default y
1087	depends on CMD_BOOTP
1088	help
1089	  Even though the config is called BOOTP_BOOTPATH, it stores the
1090	  path in the variable 'rootpath'.
1091
1092config BOOTP_DNS
1093	bool "Request & store 'dnsip' from BOOTP/DHCP server"
1094	default y
1095	depends on CMD_BOOTP
1096	help
1097	  The primary DNS server is stored as 'dnsip'. If two servers are
1098	  returned, you must set BOOTP_DNS2 to store that second server IP
1099	  also.
1100
1101config BOOTP_DNS2
1102	bool "Store 'dnsip2' from BOOTP/DHCP server"
1103	depends on BOOTP_DNS
1104	help
1105	  If a DHCP client requests the DNS server IP from a DHCP server,
1106	  it is possible that more than one DNS serverip is offered to the
1107	  client. If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1108	  server IP will be stored in the additional environment
1109	  variable "dnsip2". The first DNS serverip is always
1110	  stored in the variable "dnsip", when BOOTP_DNS is defined.
1111
1112config BOOTP_GATEWAY
1113	bool "Request & store 'gatewayip' from BOOTP/DHCP server"
1114	default y
1115	depends on CMD_BOOTP
1116
1117config BOOTP_HOSTNAME
1118	bool "Request & store 'hostname' from BOOTP/DHCP server"
1119	default y
1120	depends on CMD_BOOTP
1121	help
1122	  The name may or may not be qualified with the local domain name.
1123
1124config BOOTP_PREFER_SERVERIP
1125	bool "serverip variable takes precedent over DHCP server IP."
1126	depends on CMD_BOOTP
1127	help
1128	  By default a BOOTP/DHCP reply will overwrite the 'serverip' variable.
1129
1130	  With this option enabled, the 'serverip' variable in the environment
1131	  takes precedence over DHCP server IP and will only be set by the DHCP
1132	  server if not already set in the environment.
1133
1134config BOOTP_SUBNETMASK
1135	bool "Request & store 'netmask' from BOOTP/DHCP server"
1136	default y
1137	depends on CMD_BOOTP
1138
1139config BOOTP_NTPSERVER
1140	bool "Request & store 'ntpserverip' from BOOTP/DHCP server"
1141	depends on CMD_BOOTP
1142
1143config BOOTP_PXE
1144	bool "Send PXE client arch to BOOTP/DHCP server"
1145	default y
1146	depends on CMD_BOOTP && CMD_PXE
1147	help
1148	  Supported for ARM, ARM64, and x86 for now.
1149
1150config BOOTP_PXE_CLIENTARCH
1151	hex
1152	depends on BOOTP_PXE
1153	default 0x16 if ARM64
1154	default 0x15 if ARM
1155	default 0 if X86
1156
1157config BOOTP_VCI_STRING
1158	string
1159	depends on CMD_BOOTP
1160	default "U-Boot.armv7" if CPU_V7A || CPU_V7M || CPU_V7R
1161	default "U-Boot.armv8" if ARM64
1162	default "U-Boot.arm" if ARM
1163	default "U-Boot"
1164
1165config CMD_TFTPBOOT
1166	bool "tftpboot"
1167	default y
1168	help
1169	  tftpboot - boot image via network using TFTP protocol
1170
1171config CMD_TFTPPUT
1172	bool "tftp put"
1173	depends on CMD_TFTPBOOT
1174	help
1175	  TFTP put command, for uploading files to a server
1176
1177config CMD_TFTPSRV
1178	bool "tftpsrv"
1179	depends on CMD_TFTPBOOT
1180	help
1181	  Act as a TFTP server and boot the first received file
1182
1183config NET_TFTP_VARS
1184	bool "Control TFTP timeout and count through environment"
1185	depends on CMD_TFTPBOOT
1186	default y
1187	help
1188	  If set, allows controlling the TFTP timeout through the
1189	  environment variable tftptimeout, and the TFTP maximum
1190	  timeout count through the variable tftptimeoutcountmax.
1191	  If unset, timeout and maximum are hard-defined as 1 second
1192	  and 10 timouts per TFTP transfer.
1193
1194config CMD_RARP
1195	bool "rarpboot"
1196	help
1197	  Boot image via network using RARP/TFTP protocol
1198
1199config CMD_NFS
1200	bool "nfs"
1201	default y
1202	help
1203	  Boot image via network using NFS protocol.
1204
1205config CMD_MII
1206	bool "mii"
1207	help
1208	  Enable MII utility commands.
1209
1210config CMD_PING
1211	bool "ping"
1212	help
1213	  Send ICMP ECHO_REQUEST to network host
1214
1215config CMD_CDP
1216	bool "cdp"
1217	help
1218	  Perform CDP network configuration
1219
1220config CMD_SNTP
1221	bool "sntp"
1222	help
1223	  Synchronize RTC via network
1224
1225config CMD_DNS
1226	bool "dns"
1227	help
1228	  Lookup the IP of a hostname
1229
1230config CMD_LINK_LOCAL
1231	bool "linklocal"
1232	select LIB_RAND
1233	help
1234	  Acquire a network IP address using the link-local protocol
1235
1236endif
1237
1238config CMD_ETHSW
1239	bool "ethsw"
1240	help
1241	  Allow control of L2 Ethernet switch commands. These are supported
1242	  by the vsc9953 Ethernet driver at present. Sub-commands allow
1243	  operations such as enabling / disabling a port and
1244	  viewing/maintaining the filtering database (FDB)
1245
1246config CMD_PXE
1247	bool "pxe"
1248	select MENU
1249	help
1250	  Boot image via network using PXE protocol
1251
1252config CMD_WOL
1253	bool "wol"
1254	help
1255	  Wait for wake-on-lan Magic Packet
1256
1257endif
1258
1259menu "Misc commands"
1260
1261config CMD_BMP
1262	bool "Enable 'bmp' command"
1263	depends on LCD || DM_VIDEO || VIDEO
1264	help
1265	  This provides a way to obtain information about a BMP-format iamge
1266	  and to display it. BMP (which presumably stands for BitMaP) is a
1267	  file format defined by Microsoft which supports images of various
1268	  depths, formats and compression methods. Headers on the file
1269	  determine the formats used. This command can be used by first loading
1270	  the image into RAM, then using this command to look at it or display
1271	  it.
1272
1273config CMD_BOOTCOUNT
1274	bool "bootcount"
1275	depends on BOOTCOUNT_LIMIT
1276	help
1277	  Enable the bootcount command, which allows interrogation and
1278	  reset of the bootcounter.
1279
1280config CMD_BSP
1281	bool "Enable board-specific commands"
1282	help
1283	  (deprecated: instead, please define a Kconfig option for each command)
1284
1285	  Some boards have board-specific commands which are only enabled
1286	  during developemnt and need to be turned off for production. This
1287	  option provides a way to control this. The commands that are enabled
1288	  vary depending on the board.
1289
1290config CMD_BKOPS_ENABLE
1291	bool "mmc bkops enable"
1292	depends on CMD_MMC
1293	default n
1294	help
1295	  Enable command for setting manual background operations handshake
1296	  on a eMMC device. The feature is optionally available on eMMC devices
1297	  conforming to standard >= 4.41.
1298
1299config CMD_BLOCK_CACHE
1300	bool "blkcache - control and stats for block cache"
1301	depends on BLOCK_CACHE
1302	default y if BLOCK_CACHE
1303	help
1304	  Enable the blkcache command, which can be used to control the
1305	  operation of the cache functions.
1306	  This is most useful when fine-tuning the operation of the cache
1307	  during development, but also allows the cache to be disabled when
1308	  it might hurt performance (e.g. when using the ums command).
1309
1310config CMD_CACHE
1311	bool "icache or dcache"
1312	help
1313	  Enable the "icache" and "dcache" commands
1314
1315config CMD_DISPLAY
1316	bool "Enable the 'display' command, for character displays"
1317	help
1318	  (this needs porting to driver model)
1319	  This enables the 'display' command which allows a string to be
1320	  displayed on a simple board-specific display. Implement
1321	  display_putc() to use it.
1322
1323config CMD_LED
1324	bool "led"
1325	default y if LED
1326	help
1327	  Enable the 'led' command which allows for control of LEDs supported
1328	  by the board. The LEDs can be listed with 'led list' and controlled
1329	  with led on/off/togle/blink. Any LED drivers can be controlled with
1330	  this command, e.g. led_gpio.
1331
1332config CMD_DATE
1333	bool "date"
1334	default y if DM_RTC
1335	help
1336	  Enable the 'date' command for getting/setting the time/date in RTC
1337	  devices.
1338
1339config CMD_TIME
1340	bool "time"
1341	help
1342	  Run commands and summarize execution time.
1343
1344config CMD_GETTIME
1345	bool "gettime - read elapsed time"
1346	help
1347	  Enable the 'gettime' command which reads the elapsed time since
1348	  U-Boot started running. This shows the time in seconds and
1349	  milliseconds. See also the 'bootstage' command which provides more
1350	  flexibility for boot timing.
1351
1352# TODO: rename to CMD_SLEEP
1353config CMD_MISC
1354	bool "sleep"
1355	default y
1356	help
1357	  Delay execution for some time
1358
1359config MP
1360	bool "support for multiprocessor"
1361	help
1362	  This provides an option to brinup
1363	  different processors in multiprocessor
1364	  cases.
1365
1366config CMD_TIMER
1367	bool "timer"
1368	help
1369	  Access the system timer.
1370
1371config CMD_SOUND
1372	bool "sound"
1373	depends on SOUND
1374	help
1375	  This provides basic access to the U-Boot's sound support. The main
1376	  feature is to play a beep.
1377
1378	     sound init   - set up sound system
1379	     sound play   - play a sound
1380
1381config CMD_QFW
1382	bool "qfw"
1383	select QFW
1384	help
1385	  This provides access to the QEMU firmware interface.  The main
1386	  feature is to allow easy loading of files passed to qemu-system
1387	  via -kernel / -initrd
1388
1389source "cmd/mvebu/Kconfig"
1390
1391config CMD_TERMINAL
1392	bool "terminal - provides a way to attach a serial terminal"
1393	help
1394	  Provides a 'cu'-like serial terminal command. This can be used to
1395	  access other serial ports from the system console. The terminal
1396	  is very simple with no special processing of characters. As with
1397	  cu, you can press ~. (tilde followed by period) to exit.
1398
1399config CMD_UUID
1400	bool "uuid, guid - generation of unique IDs"
1401	select LIB_UUID
1402	help
1403	  This enables two commands:
1404
1405	     uuid - generate random Universally Unique Identifier
1406	     guid - generate Globally Unique Identifier based on random UUID
1407
1408	  The two commands are very similar except for the endianness of the
1409	  output.
1410
1411endmenu
1412
1413source "cmd/ti/Kconfig"
1414
1415config CMD_BOOTSTAGE
1416	bool "Enable the 'bootstage' command"
1417	depends on BOOTSTAGE
1418	help
1419	  Add a 'bootstage' command which supports printing a report
1420	  and un/stashing of bootstage data.
1421
1422menu "Power commands"
1423config CMD_PMIC
1424	bool "Enable Driver Model PMIC command"
1425	depends on DM_PMIC
1426	help
1427	  This is the pmic command, based on a driver model pmic's API.
1428	  Command features are unchanged:
1429	  - list               - list pmic devices
1430	  - pmic dev <id>      - show or [set] operating pmic device (NEW)
1431	  - pmic dump          - dump registers
1432	  - pmic read address  - read byte of register at address
1433	  - pmic write address - write byte to register at address
1434	  The only one change for this command is 'dev' subcommand.
1435
1436config CMD_REGULATOR
1437	bool "Enable Driver Model REGULATOR command"
1438	depends on DM_REGULATOR
1439	help
1440	  This command is based on driver model regulator's API.
1441	  User interface features:
1442	  - list               - list regulator devices
1443	  - regulator dev <id> - show or [set] operating regulator device
1444	  - regulator info     - print constraints info
1445	  - regulator status   - print operating status
1446	  - regulator value <val] <-f> - print/[set] voltage value [uV]
1447	  - regulator current <val>    - print/[set] current value [uA]
1448	  - regulator mode <id>        - print/[set] operating mode id
1449	  - regulator enable           - enable the regulator output
1450	  - regulator disable          - disable the regulator output
1451
1452	  The '-f' (force) option can be used for set the value which exceeds
1453	  the limits, which are found in device-tree and are kept in regulator's
1454	  uclass platdata structure.
1455
1456endmenu
1457
1458menu "Security commands"
1459config CMD_AES
1460	bool "Enable the 'aes' command"
1461	select AES
1462	help
1463	  This provides a means to encrypt and decrypt data using the AES
1464	  (Advanced Encryption Standard). This algorithm uses a symetric key
1465	  and is widely used as a streaming cipher. Different key lengths are
1466	  supported by the algorithm but this command only supports 128 bits
1467	  at present.
1468
1469config CMD_BLOB
1470	bool "Enable the 'blob' command"
1471	help
1472	  This is used with the Freescale secure boot mechanism.
1473
1474	  Freescale's SEC block has built-in Blob Protocol which provides
1475	  a method for protecting user-defined data across system power
1476	  cycles. SEC block protects data in a data structure called a Blob,
1477	  which provides both confidentiality and integrity protection.
1478
1479	  Encapsulating data as a blob
1480	  Each time that the Blob Protocol is used to protect data, a
1481	  different randomly generated key is used to encrypt the data.
1482	  This random key is itself encrypted using a key which is derived
1483	  from SoC's non-volatile secret key and a 16 bit Key identifier.
1484	  The resulting encrypted key along with encrypted data is called a
1485	  blob. The non-volatile secure key is available for use only during
1486	  secure boot.
1487
1488	  During decapsulation, the reverse process is performed to get back
1489	  the original data.
1490
1491	  Sub-commands:
1492            blob enc - encapsulating data as a cryptgraphic blob
1493	    blob dec - decapsulating cryptgraphic blob to get the data
1494
1495	  Syntax:
1496
1497	  blob enc src dst len km
1498
1499	  Encapsulate and create blob of data $len bytes long
1500	  at address $src and store the result at address $dst.
1501	  $km is the 16 byte key modifier is also required for
1502	  generation/use as key for cryptographic operation. Key
1503	  modifier should be 16 byte long.
1504
1505	  blob dec src dst len km
1506
1507	  Decapsulate the  blob of data at address $src and
1508	  store result of $len byte at addr $dst.
1509	  $km is the 16 byte key modifier is also required for
1510	  generation/use as key for cryptographic operation. Key
1511	  modifier should be 16 byte long.
1512
1513config CMD_HASH
1514	bool "Support 'hash' command"
1515	select HASH
1516	help
1517	  This provides a way to hash data in memory using various supported
1518	  algorithms (such as SHA1, MD5, CRC32). The computed digest can be
1519	  saved to memory or to an environment variable. It is also possible
1520	  to verify a hash against data in memory.
1521
1522config CMD_HVC
1523	bool "Support the 'hvc' command"
1524	depends on ARM_SMCCC
1525	help
1526	  Allows issuing Hypervisor Calls (HVCs). Mostly useful for
1527	  development and testing.
1528
1529config CMD_SMC
1530	bool "Support the 'smc' command"
1531	depends on ARM_SMCCC
1532	help
1533	  Allows issuing Secure Monitor Calls (SMCs). Mostly useful for
1534	  development and testing.
1535
1536config HASH_VERIFY
1537	bool "hash -v"
1538	depends on CMD_HASH
1539	help
1540	  Add -v option to verify data against a hash.
1541
1542config CMD_TPM_V1
1543	bool
1544
1545config CMD_TPM_V2
1546	bool
1547
1548config CMD_TPM
1549	bool "Enable the 'tpm' command"
1550	depends on TPM_V1 || TPM_V2
1551	select CMD_TPM_V1 if TPM_V1
1552	select CMD_TPM_V2 if TPM_V2
1553	help
1554	  This provides a means to talk to a TPM from the command line. A wide
1555	  range of commands if provided - see 'tpm help' for details. The
1556	  command requires a suitable TPM on your board and the correct driver
1557	  must be enabled.
1558
1559if CMD_TPM
1560
1561config CMD_TPM_TEST
1562	bool "Enable the 'tpm test' command"
1563	depends on TPM_V1
1564	help
1565	  This provides a a series of tests to confirm that the TPMv1.x is
1566	  working correctly. The tests cover initialisation, non-volatile RAM,
1567	  extend, global lock and checking that timing is within expectations.
1568	  The tests pass correctly on Infineon TPMs but may need to be adjusted
1569	  for other devices.
1570
1571endif
1572
1573endmenu
1574
1575menu "Firmware commands"
1576config CMD_CROS_EC
1577	bool "Enable crosec command"
1578	depends on CROS_EC
1579	default y
1580	help
1581	  Enable command-line access to the Chrome OS EC (Embedded
1582	  Controller). This provides the 'crosec' command which has
1583	  a number of sub-commands for performing EC tasks such as
1584	  updating its flash, accessing a small saved context area
1585	  and talking to the I2C bus behind the EC (if there is one).
1586endmenu
1587
1588menu "Filesystem commands"
1589config CMD_BTRFS
1590	bool "Enable the 'btrsubvol' command"
1591	select FS_BTRFS
1592	help
1593	  This enables the 'btrsubvol' command to list subvolumes
1594	  of a BTRFS filesystem. There are no special commands for
1595	  listing BTRFS directories or loading BTRFS files - this
1596	  can be done by the generic 'fs' commands (see CMD_FS_GENERIC)
1597	  when BTRFS is enabled (see FS_BTRFS).
1598
1599config CMD_CBFS
1600	bool "Enable the 'cbfs' command"
1601	depends on FS_CBFS
1602	help
1603	  Define this to enable support for reading from a Coreboot
1604	  filesystem. This is a ROM-based filesystem used for accessing files
1605	  on systems that use coreboot as the first boot-loader and then load
1606	  U-Boot to actually boot the Operating System. Available commands are
1607	  cbfsinit, cbfsinfo, cbfsls and cbfsload.
1608
1609config CMD_CRAMFS
1610	bool "Enable the 'cramfs' command"
1611	depends on FS_CRAMFS
1612	help
1613	  This provides commands for dealing with CRAMFS (Compressed ROM
1614	  filesystem). CRAMFS is useful when space is tight since files are
1615	  compressed. Two commands are provided:
1616
1617	     cramfsls   - lists files in a cramfs image
1618	     cramfsload - loads a file from a cramfs image
1619
1620config CMD_EXT2
1621	bool "ext2 command support"
1622	select FS_EXT4
1623	help
1624	  Enables EXT2 FS command
1625
1626config CMD_EXT4
1627	bool "ext4 command support"
1628	select FS_EXT4
1629	help
1630	  Enables EXT4 FS command
1631
1632config CMD_EXT4_WRITE
1633	depends on CMD_EXT4
1634	bool "ext4 write command support"
1635	select EXT4_WRITE
1636	help
1637	  Enables EXT4 FS write command
1638
1639config CMD_FAT
1640	bool "FAT command support"
1641	select FS_FAT
1642	help
1643	  Support for the FAT fs
1644
1645config CMD_FS_GENERIC
1646	bool "filesystem commands"
1647	help
1648	  Enables filesystem commands (e.g. load, ls) that work for multiple
1649	  fs types.
1650
1651config CMD_FS_UUID
1652	bool "fsuuid command"
1653	help
1654	  Enables fsuuid command for filesystem UUID.
1655
1656config CMD_JFFS2
1657	bool "jffs2 command"
1658	select FS_JFFS2
1659	help
1660	  Enables commands to support the JFFS2 (Journalling Flash File System
1661	  version 2) filesystem. This enables fsload, ls and fsinfo which
1662	  provide the ability to load files, list directories and obtain
1663	  filesystem information.
1664
1665config CMD_MTDPARTS
1666	bool "MTD partition support"
1667	help
1668	  MTD partition support
1669
1670config MTDIDS_DEFAULT
1671	string "Default MTD IDs"
1672	depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH
1673	help
1674	  Defines a default MTD IDs list for use with MTD partitions in the
1675	  Linux MTD command line partitions format.
1676
1677config MTDPARTS_DEFAULT
1678	string "Default MTD partition scheme"
1679	depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH
1680	help
1681	  Defines a default MTD partitioning scheme in the Linux MTD command
1682	  line partitions format
1683
1684config CMD_MTDPARTS_SPREAD
1685	bool "Padd partition size to take account of bad blocks"
1686	depends on CMD_MTDPARTS
1687	help
1688	  This enables the 'spread' sub-command of the mtdparts command.
1689	  This command will modify the existing mtdparts variable by increasing
1690	  the size of the partitions such that 1) each partition's net size is
1691	  at least as large as the size specified in the mtdparts variable and
1692	  2) each partition starts on a good block.
1693
1694config CMD_REISER
1695	bool "reiser - Access to reiserfs filesystems"
1696	help
1697	  This provides two commands which operate on a resierfs filesystem,
1698	  commonly used some years ago:
1699
1700	    reiserls - list files
1701	    reiserload - load a file
1702
1703config CMD_YAFFS2
1704	bool "yaffs2 - Access of YAFFS2 filesystem"
1705	depends on YAFFS2
1706	default y
1707	help
1708	  This provides commands for accessing a YAFFS2 filesystem. Yet
1709	  Another Flash Filesystem 2 is a filesystem designed specifically
1710	  for NAND flash. It incorporates bad-block management and ensures
1711	  that device writes are sequential regardless of filesystem
1712	  activity.
1713
1714config CMD_ZFS
1715	bool "zfs - Access of ZFS filesystem"
1716	help
1717	  This provides commands to accessing a ZFS filesystem, commonly used
1718	  on Solaris systems. Two sub-commands are provided:
1719
1720	    zfsls - list files in a directory
1721	    zfsload - load a file
1722
1723	  See doc/README.zfs for more details.
1724
1725endmenu
1726
1727menu "Debug commands"
1728
1729config CMD_BEDBUG
1730	bool "bedbug"
1731	help
1732	  The bedbug (emBEDded deBUGger) command provides debugging features
1733	  for some PowerPC processors. For details please see the
1734	  docuemntation in doc/README.beddbug
1735
1736config CMD_DIAG
1737	bool "diag - Board diagnostics"
1738	help
1739	  This command provides access to board diagnostic tests. These are
1740	  called Power-on Self Tests (POST). The command allows listing of
1741	  available tests and running either all the tests, or specific tests
1742	  identified by name.
1743
1744config CMD_IRQ
1745	bool "irq - Show information about interrupts"
1746	depends on !ARM && !MIPS && !SH
1747	help
1748	  This enables two commands:
1749
1750	     interrupts - enable or disable interrupts
1751	     irqinfo - print device-specific interrupt information
1752
1753config CMD_KGDB
1754	bool "kgdb - Allow debugging of U-Boot with gdb"
1755	help
1756	  This enables a 'kgdb' command which allows gdb to connect to U-Boot
1757	  over a serial link for debugging purposes. This allows
1758	  single-stepping, inspecting variables, etc. This is supported only
1759	  on PowerPC at present.
1760
1761config CMD_LOG
1762	bool "log - Generation, control and access to logging"
1763	select LOG
1764	help
1765	  This provides access to logging features. It allows the output of
1766	  log data to be controlled to a limited extent (setting up the default
1767	  maximum log level for emitting of records). It also provides access
1768	  to a command used for testing the log system.
1769
1770config CMD_TRACE
1771	bool "trace - Support tracing of function calls and timing"
1772	help
1773	  Enables a command to control using of function tracing within
1774	  U-Boot. This allows recording of call traces including timing
1775	  information. The command can write data to memory for exporting
1776	  for analsys (e.g. using bootchart). See doc/README.trace for full
1777	  details.
1778
1779config CMD_AVB
1780	bool "avb - Android Verified Boot 2.0 operations"
1781	depends on LIBAVB
1782	default n
1783	help
1784	  Enables a "avb" command to perform verification of partitions using
1785	  Android Verified Boot 2.0 functionality. It includes such subcommands:
1786	    avb init - initialize avb2 subsystem
1787	    avb read_rb - read rollback index
1788	    avb write_rb - write rollback index
1789	    avb is_unlocked - check device lock state
1790	    avb get_uuid - read and print uuid of a partition
1791	    avb read_part - read data from partition
1792	    avb read_part_hex - read data from partition and output to stdout
1793	    avb write_part - write data to partition
1794	    avb verify - run full verification chain
1795endmenu
1796
1797config CMD_UBI
1798	tristate "Enable UBI - Unsorted block images commands"
1799	select CRC32
1800	select MTD_UBI
1801	select CMD_MTDPARTS
1802	default y if NAND_SUNXI
1803	help
1804	  UBI is a software layer above MTD layer which admits use of LVM-like
1805	  logical volumes on top of MTD devices, hides some complexities of
1806	  flash chips like wear and bad blocks and provides some other useful
1807	  capabilities. Please, consult the MTD web site for more details
1808	  (www.linux-mtd.infradead.org). Activate this option if you want
1809	  to use U-Boot UBI commands.
1810
1811config CMD_UBIFS
1812	tristate "Enable UBIFS - Unsorted block images filesystem commands"
1813	depends on CMD_UBI
1814	select CRC32
1815	select LZO
1816	default y if CMD_UBI
1817	help
1818	  UBIFS is a file system for flash devices which works on top of UBI.
1819
1820endmenu
1821