1menu "Command line interface" 2 3config CMDLINE 4 bool "Support U-Boot commands" 5 default y 6 help 7 Enable U-Boot's command-line functions. This provides a means 8 to enter commands into U-Boot for a wide variety of purposes. It 9 also allows scripts (containing commands) to be executed. 10 Various commands and command categorys can be indivdually enabled. 11 Depending on the number of commands enabled, this can add 12 substantially to the size of U-Boot. 13 14config HUSH_PARSER 15 bool "Use hush shell" 16 depends on CMDLINE 17 help 18 This option enables the "hush" shell (from Busybox) as command line 19 interpreter, thus enabling powerful command line syntax like 20 if...then...else...fi conditionals or `&&' and '||' 21 constructs ("shell scripts"). 22 23 If disabled, you get the old, much simpler behaviour with a somewhat 24 smaller memory footprint. 25 26config CMDLINE_EDITING 27 bool "Enable command line editing" 28 depends on CMDLINE 29 default y 30 help 31 Enable editing and History functions for interactive command line 32 input operations 33 34config AUTO_COMPLETE 35 bool "Enable auto complete using TAB" 36 depends on CMDLINE 37 default y 38 help 39 Enable auto completion of commands using TAB. 40 41config SYS_LONGHELP 42 bool "Enable long help messages" 43 depends on CMDLINE 44 default y if CMDLINE 45 help 46 Defined when you want long help messages included 47 Do not set this option when short of memory. 48 49config SYS_PROMPT 50 string "Shell prompt" 51 default "=> " 52 help 53 This string is displayed in the command line to the left of the 54 cursor. 55 56menu "Autoboot options" 57 58config AUTOBOOT 59 bool "Autoboot" 60 default y 61 help 62 This enables the autoboot. See doc/README.autoboot for detail. 63 64config AUTOBOOT_KEYED 65 bool "Stop autobooting via specific input key / string" 66 default n 67 help 68 This option enables stopping (aborting) of the automatic 69 boot feature only by issuing a specific input key or 70 string. If not enabled, any input key will abort the 71 U-Boot automatic booting process and bring the device 72 to the U-Boot prompt for user input. 73 74config AUTOBOOT_PROMPT 75 string "Autoboot stop prompt" 76 depends on AUTOBOOT_KEYED 77 default "Autoboot in %d seconds\\n" 78 help 79 This string is displayed before the boot delay selected by 80 CONFIG_BOOTDELAY starts. If it is not defined there is no 81 output indicating that autoboot is in progress. 82 83 Note that this define is used as the (only) argument to a 84 printf() call, so it may contain '%' format specifications, 85 provided that it also includes, sepearated by commas exactly 86 like in a printf statement, the required arguments. It is 87 the responsibility of the user to select only such arguments 88 that are valid in the given context. 89 90config AUTOBOOT_ENCRYPTION 91 bool "Enable encryption in autoboot stopping" 92 depends on AUTOBOOT_KEYED 93 default n 94 95config AUTOBOOT_DELAY_STR 96 string "Delay autobooting via specific input key / string" 97 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 98 help 99 This option delays the automatic boot feature by issuing 100 a specific input key or string. If CONFIG_AUTOBOOT_DELAY_STR 101 or the environment variable "bootdelaykey" is specified 102 and this string is received from console input before 103 autoboot starts booting, U-Boot gives a command prompt. The 104 U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is 105 used, otherwise it never times out. 106 107config AUTOBOOT_STOP_STR 108 string "Stop autobooting via specific input key / string" 109 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 110 help 111 This option enables stopping (aborting) of the automatic 112 boot feature only by issuing a specific input key or 113 string. If CONFIG_AUTOBOOT_STOP_STR or the environment 114 variable "bootstopkey" is specified and this string is 115 received from console input before autoboot starts booting, 116 U-Boot gives a command prompt. The U-Boot prompt never 117 times out, even if CONFIG_BOOT_RETRY_TIME is used. 118 119config AUTOBOOT_KEYED_CTRLC 120 bool "Enable Ctrl-C autoboot interruption" 121 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 122 default n 123 help 124 This option allows for the boot sequence to be interrupted 125 by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey". 126 Setting this variable provides an escape sequence from the 127 limited "password" strings. 128 129config AUTOBOOT_STOP_STR_SHA256 130 string "Stop autobooting via SHA256 encrypted password" 131 depends on AUTOBOOT_KEYED && AUTOBOOT_ENCRYPTION 132 help 133 This option adds the feature to only stop the autobooting, 134 and therefore boot into the U-Boot prompt, when the input 135 string / password matches a values that is encypted via 136 a SHA256 hash and saved in the environment. 137 138endmenu 139 140config BUILD_BIN2C 141 bool 142 143comment "Commands" 144 145menu "Info commands" 146 147config CMD_BDI 148 bool "bdinfo" 149 default y 150 help 151 Print board info 152 153config CMD_CONFIG 154 bool "config" 155 select BUILD_BIN2C 156 default SANDBOX 157 help 158 Print ".config" contents. 159 160 If this option is enabled, the ".config" file contents are embedded 161 in the U-Boot image and can be printed on the console by the "config" 162 command. This provides information of which options are enabled on 163 the running U-Boot. 164 165config CMD_CONSOLE 166 bool "coninfo" 167 default y 168 help 169 Print console devices and information. 170 171config CMD_CPU 172 bool "cpu" 173 help 174 Print information about available CPUs. This normally shows the 175 number of CPUs, type (e.g. manufacturer, architecture, product or 176 internal name) and clock frequency. Other information may be 177 available depending on the CPU driver. 178 179config CMD_LICENSE 180 bool "license" 181 select BUILD_BIN2C 182 help 183 Print GPL license text 184 185config CMD_REGINFO 186 bool "reginfo" 187 depends on PPC 188 help 189 Register dump 190 191endmenu 192 193menu "Boot commands" 194 195config CMD_BOOTD 196 bool "bootd" 197 default y 198 help 199 Run the command stored in the environment "bootcmd", i.e. 200 "bootd" does the same thing as "run bootcmd". 201 202config CMD_BOOTM 203 bool "bootm" 204 default y 205 help 206 Boot an application image from the memory. 207 208config CMD_BOOTZ 209 bool "bootz" 210 help 211 Boot the Linux zImage 212 213config CMD_BOOTI 214 bool "booti" 215 depends on ARM64 216 default y 217 help 218 Boot an AArch64 Linux Kernel image from memory. 219 220config CMD_BOOTEFI 221 bool "bootefi" 222 depends on EFI_LOADER 223 default y 224 help 225 Boot an EFI image from memory. 226 227config CMD_BOOTEFI_HELLO_COMPILE 228 bool "Compile a standard EFI hello world binary for testing" 229 depends on CMD_BOOTEFI && (ARM || X86 || RISCV) 230 default y 231 help 232 This compiles a standard EFI hello world application with U-Boot so 233 that it can be used with the test/py testing framework. This is useful 234 for testing that EFI is working at a basic level, and for bringing 235 up EFI support on a new architecture. 236 237 No additional space will be required in the resulting U-Boot binary 238 when this option is enabled. 239 240config CMD_BOOTEFI_HELLO 241 bool "Allow booting a standard EFI hello world for testing" 242 depends on CMD_BOOTEFI_HELLO_COMPILE 243 help 244 This adds a standard EFI hello world application to U-Boot so that 245 it can be used with the 'bootefi hello' command. This is useful 246 for testing that EFI is working at a basic level, and for bringing 247 up EFI support on a new architecture. 248 249source lib/efi_selftest/Kconfig 250 251config CMD_BOOTMENU 252 bool "bootmenu" 253 select MENU 254 help 255 Add an ANSI terminal boot menu command. 256 257config CMD_ELF 258 bool "bootelf, bootvx" 259 default y 260 help 261 Boot an ELF/vxWorks image from the memory. 262 263config CMD_FDT 264 bool "Flattened Device Tree utility commands" 265 default y 266 depends on OF_LIBFDT 267 help 268 Do FDT related setup before booting into the Operating System. 269 270config CMD_GO 271 bool "go" 272 default y 273 help 274 Start an application at a given address. 275 276config CMD_RUN 277 bool "run" 278 default y 279 help 280 Run the command in the given environment variable. 281 282config CMD_IMI 283 bool "iminfo" 284 default y 285 help 286 Print header information for application image. 287 288config CMD_IMLS 289 bool "imls" 290 help 291 List all images found in flash 292 293config CMD_XIMG 294 bool "imxtract" 295 default y 296 help 297 Extract a part of a multi-image. 298 299config CMD_POWEROFF 300 bool "poweroff" 301 help 302 Poweroff/Shutdown the system 303 304config CMD_SPL 305 bool "spl export - Export boot information for Falcon boot" 306 depends on SPL 307 help 308 Falcon mode allows booting directly from SPL into an Operating 309 System such as Linux, thus skipping U-Boot proper. See 310 doc/README.falcon for full information about how to use this 311 command. 312 313config CMD_SPL_NAND_OFS 314 hex "Offset of OS command line args for Falcon-mode NAND boot" 315 depends on CMD_SPL 316 default 0 317 help 318 This provides the offset of the command line arguments for Linux 319 when booting from NAND in Falcon mode. See doc/README.falcon 320 for full information about how to use this option (and also see 321 board/gateworks/gw_ventana/README for an example). 322 323config CMD_SPL_WRITE_SIZE 324 hex "Size of argument area" 325 depends on CMD_SPL 326 default 0x2000 327 help 328 This provides the size of the command-line argument area in NAND 329 flash used by Falcon-mode boot. See the documentation until CMD_SPL 330 for detail. 331 332config CMD_FITUPD 333 bool "fitImage update command" 334 help 335 Implements the 'fitupd' command, which allows to automatically 336 store software updates present on a TFTP server in NOR Flash 337 338config CMD_THOR_DOWNLOAD 339 bool "thor - TIZEN 'thor' download" 340 help 341 Implements the 'thor' download protocol. This is a way of 342 downloading a software update over USB from an attached host. 343 There is no documentation about this within the U-Boot source code 344 but you should be able to find something on the interwebs. 345 346config CMD_ZBOOT 347 bool "zboot - x86 boot command" 348 help 349 With x86 machines it is common to boot a bzImage file which 350 contains both a kernel and a setup.bin file. The latter includes 351 configuration information from the dark ages which x86 boards still 352 need to pick things out of. 353 354 Consider using FIT in preference to this since it supports directly 355 booting both 32- and 64-bit kernels, as well as secure boot. 356 Documentation is available in doc/uImage.FIT/x86-fit-boot.txt 357 358endmenu 359 360menu "Environment commands" 361 362config CMD_ASKENV 363 bool "ask for env variable" 364 help 365 Ask for environment variable 366 367config CMD_EXPORTENV 368 bool "env export" 369 default y 370 help 371 Export environments. 372 373config CMD_IMPORTENV 374 bool "env import" 375 default y 376 help 377 Import environments. 378 379config CMD_EDITENV 380 bool "editenv" 381 default y 382 help 383 Edit environment variable. 384 385config CMD_GREPENV 386 bool "search env" 387 help 388 Allow for searching environment variables 389 390config CMD_SAVEENV 391 bool "saveenv" 392 default y 393 help 394 Save all environment variables into the compiled-in persistent 395 storage. 396 397config CMD_ENV_EXISTS 398 bool "env exists" 399 default y 400 help 401 Check if a variable is defined in the environment for use in 402 shell scripting. 403 404config CMD_ENV_CALLBACK 405 bool "env callbacks - print callbacks and their associated variables" 406 help 407 Some environment variable have callbacks defined by 408 U_BOOT_ENV_CALLBACK. These are called when the variable changes. 409 For example changing "baudrate" adjust the serial baud rate. This 410 command lists the currently defined callbacks. 411 412config CMD_ENV_FLAGS 413 bool "env flags -print variables that have non-default flags" 414 help 415 Some environment variables have special flags that control their 416 behaviour. For example, serial# can only be written once and cannot 417 be deleted. This command shows the variables that have special 418 flags. 419 420endmenu 421 422menu "Memory commands" 423 424config CMD_BINOP 425 bool "binop" 426 help 427 Compute binary operations (xor, or, and) of byte arrays of arbitrary 428 size from memory and store the result in memory or the environment. 429 430config CMD_CRC32 431 bool "crc32" 432 select HASH 433 default y 434 help 435 Compute CRC32. 436 437config CRC32_VERIFY 438 bool "crc32 -v" 439 depends on CMD_CRC32 440 help 441 Add -v option to verify data against a crc32 checksum. 442 443config CMD_EEPROM 444 bool "eeprom - EEPROM subsystem" 445 help 446 (deprecated, needs conversion to driver model) 447 Provides commands to read and write EEPROM (Electrically Erasable 448 Programmable Read Only Memory) chips that are connected over an 449 I2C bus. 450 451config CMD_EEPROM_LAYOUT 452 bool "Enable layout-aware eeprom commands" 453 depends on CMD_EEPROM 454 help 455 (deprecated, needs conversion to driver model) 456 When enabled, additional eeprom sub-commands become available. 457 458 eeprom print - prints the contents of the eeprom in a human-readable 459 way (eeprom layout fields, and data formatted to be fit for human 460 consumption). 461 462 eeprom update - allows user to update eeprom fields by specifying 463 the field name, and providing the new data in a human readable format 464 (same format as displayed by the eeprom print command). 465 466 Both commands can either auto detect the layout, or be told which 467 layout to use. 468 469 Feature API: 470 __weak int parse_layout_version(char *str) 471 - override to provide your own layout name parsing 472 __weak void __eeprom_layout_assign(struct eeprom_layout *layout, 473 int layout_version); 474 - override to setup the layout metadata based on the version 475 __weak int eeprom_layout_detect(unsigned char *data) 476 - override to provide your own algorithm for detecting layout 477 version 478 eeprom_field.c 479 - contains various printing and updating functions for common 480 types of eeprom fields. Can be used for defining 481 custom layouts. 482 483config EEPROM_LAYOUT_HELP_STRING 484 string "Tells user what layout names are supported" 485 depends on CMD_EEPROM_LAYOUT 486 default "<not defined>" 487 help 488 Help printed with the LAYOUT VERSIONS part of the 'eeprom' 489 command's help. 490 491config LOOPW 492 bool "loopw" 493 help 494 Infinite write loop on address range 495 496config CMD_MD5SUM 497 bool "md5sum" 498 default n 499 select MD5 500 help 501 Compute MD5 checksum. 502 503config MD5SUM_VERIFY 504 bool "md5sum -v" 505 default n 506 depends on CMD_MD5SUM 507 help 508 Add -v option to verify data against an MD5 checksum. 509 510config CMD_MEMINFO 511 bool "meminfo" 512 help 513 Display memory information. 514 515config CMD_MEMORY 516 bool "md, mm, nm, mw, cp, cmp, base, loop" 517 default y 518 help 519 Memory commands. 520 md - memory display 521 mm - memory modify (auto-incrementing address) 522 nm - memory modify (constant address) 523 mw - memory write (fill) 524 cp - memory copy 525 cmp - memory compare 526 base - print or set address offset 527 loop - initialize loop on address range 528 529config CMD_MEMTEST 530 bool "memtest" 531 help 532 Simple RAM read/write test. 533 534if CMD_MEMTEST 535 536config SYS_ALT_MEMTEST 537 bool "Alternative test" 538 help 539 Use a more complete alternative memory test. 540 541endif 542 543config CMD_MX_CYCLIC 544 bool "mdc, mwc" 545 help 546 mdc - memory display cyclic 547 mwc - memory write cyclic 548 549config CMD_SHA1SUM 550 bool "sha1sum" 551 select SHA1 552 help 553 Compute SHA1 checksum. 554 555config SHA1SUM_VERIFY 556 bool "sha1sum -v" 557 depends on CMD_SHA1SUM 558 help 559 Add -v option to verify data against a SHA1 checksum. 560 561config CMD_STRINGS 562 bool "strings - display strings in memory" 563 help 564 This works similarly to the Unix 'strings' command except that it 565 works with a memory range. String of printable characters found 566 within the range are displayed. The minimum number of characters 567 for a sequence to be considered a string can be provided. 568 569endmenu 570 571menu "Compression commands" 572 573config CMD_LZMADEC 574 bool "lzmadec" 575 default y if CMD_BOOTI 576 select LZMA 577 help 578 Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm) 579 image from memory. 580 581config CMD_UNZIP 582 bool "unzip" 583 default y if CMD_BOOTI 584 help 585 Uncompress a zip-compressed memory region. 586 587config CMD_ZIP 588 bool "zip" 589 help 590 Compress a memory region with zlib deflate method. 591 592endmenu 593 594menu "Device access commands" 595 596config CMD_ARMFLASH 597 #depends on FLASH_CFI_DRIVER 598 bool "armflash" 599 help 600 ARM Ltd reference designs flash partition access 601 602config CMD_ADC 603 bool "adc - Access Analog to Digital Converters info and data" 604 select ADC 605 select DM_REGULATOR 606 help 607 Shows ADC device info and permit printing one-shot analog converted 608 data from a named Analog to Digital Converter. 609 610config CMD_CLK 611 bool "clk - Show clock frequencies" 612 help 613 (deprecated) 614 Shows clock frequences by calling a sock_clk_dump() hook function. 615 This is depreated in favour of using the CLK uclass and accessing 616 clock values from associated drivers. However currently no command 617 exists for this. 618 619config CMD_DEMO 620 bool "demo - Demonstration commands for driver model" 621 depends on DM 622 help 623 Provides a 'demo' command which can be used to play around with 624 driver model. To use this properly you will need to enable one or 625 both of the demo devices (DM_DEMO_SHAPE and DM_DEMO_SIMPLE). 626 Otherwise you will always get an empty list of devices. The demo 627 devices are defined in the sandbox device tree, so the easiest 628 option is to use sandbox and pass the -d point to sandbox's 629 u-boot.dtb file. 630 631config CMD_DFU 632 bool "dfu" 633 select DFU 634 help 635 Enables the command "dfu" which is used to have U-Boot create a DFU 636 class device via USB. This command requires that the "dfu_alt_info" 637 environment variable be set and define the alt settings to expose to 638 the host. 639 640config CMD_DM 641 bool "dm - Access to driver model information" 642 depends on DM 643 default y 644 help 645 Provides access to driver model data structures and information, 646 such as a list of devices, list of uclasses and the state of each 647 device (e.g. activated). This is not required for operation, but 648 can be useful to see the state of driver model for debugging or 649 interest. 650 651config CMD_FASTBOOT 652 bool "fastboot - Android fastboot support" 653 depends on FASTBOOT 654 help 655 This enables the command "fastboot" which enables the Android 656 fastboot mode for the platform. Fastboot is a protocol for 657 downloading images, flashing and device control used on 658 Android devices. Fastboot requires either the network stack 659 enabled or support for acting as a USB device. 660 661 See doc/README.android-fastboot for more information. 662 663config CMD_FDC 664 bool "fdcboot - Boot from floppy device" 665 help 666 The 'fdtboot' command allows booting an image from a floppy disk. 667 668config CMD_FLASH 669 bool "flinfo, erase, protect" 670 default y 671 help 672 NOR flash support. 673 flinfo - print FLASH memory information 674 erase - FLASH memory 675 protect - enable or disable FLASH write protection 676 677config CMD_FPGA 678 bool "fpga" 679 depends on FPGA 680 default y 681 help 682 FPGA support. 683 684config CMD_FPGA_LOADBP 685 bool "fpga loadbp - load partial bitstream (Xilinx only)" 686 depends on CMD_FPGA 687 help 688 Supports loading an FPGA device from a bitstream buffer containing 689 a partial bitstream. 690 691config CMD_FPGA_LOADFS 692 bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)" 693 depends on CMD_FPGA 694 help 695 Supports loading an FPGA device from a FAT filesystem. 696 697config CMD_FPGA_LOADMK 698 bool "fpga loadmk - load bitstream from image" 699 depends on CMD_FPGA 700 help 701 Supports loading an FPGA device from a image generated by mkimage. 702 703config CMD_FPGA_LOADP 704 bool "fpga loadp - load partial bitstream" 705 depends on CMD_FPGA 706 help 707 Supports loading an FPGA device from a bitstream buffer containing 708 a partial bitstream. 709 710config CMD_FPGA_LOAD_SECURE 711 bool "fpga loads - loads secure bitstreams (Xilinx only)" 712 depends on CMD_FPGA 713 help 714 Enables the fpga loads command which is used to load secure 715 (authenticated or encrypted or both) bitstreams on to FPGA. 716 717config CMD_FPGAD 718 bool "fpgad - dump FPGA registers" 719 help 720 (legacy, needs conversion to driver model) 721 Provides a way to dump FPGA registers by calling the board-specific 722 fpga_get_reg() function. This functions similarly to the 'md' 723 command. 724 725config CMD_FUSE 726 bool "fuse - support for the fuse subssystem" 727 help 728 (deprecated - needs conversion to driver model) 729 This allows reading, sensing, programming or overriding fuses 730 which control the behaviour of the device. The command uses the 731 fuse_...() API. 732 733config CMD_GPIO 734 bool "gpio" 735 help 736 GPIO support. 737 738config CMD_GPT 739 bool "GPT (GUID Partition Table) command" 740 select PARTITION_UUIDS 741 select EFI_PARTITION 742 select HAVE_BLOCK_DEVICE 743 imply RANDOM_UUID 744 help 745 Enable the 'gpt' command to ready and write GPT style partition 746 tables. 747 748config RANDOM_UUID 749 bool "GPT Random UUID generation" 750 select LIB_UUID 751 help 752 Enable the generation of partitions with random UUIDs if none 753 are provided. 754 755config CMD_GPT_RENAME 756 bool "GPT partition renaming commands" 757 depends on CMD_GPT 758 help 759 Enables the 'gpt' command to interchange names on two GPT 760 partitions via the 'gpt swap' command or to rename single 761 partitions via the 'rename' command. 762 763config CMD_IDE 764 bool "ide - Support for IDE drivers" 765 select IDE 766 help 767 Provides an 'ide' command which allows accessing the IDE drive, 768 reseting the IDE interface, printing the partition table and 769 geting device info. It also enables the 'diskboot' command which 770 permits booting from an IDE drive. 771 772config CMD_IO 773 bool "io - Support for performing I/O accesses" 774 help 775 Provides an 'iod' command to display I/O space and an 'iow' command 776 to write values to the I/O space. This can be useful for manually 777 checking the state of devices during boot when debugging device 778 drivers, etc. 779 780config CMD_IOTRACE 781 bool "iotrace - Support for tracing I/O activity" 782 help 783 Provides an 'iotrace' command which supports recording I/O reads and 784 writes in a trace buffer in memory . It also maintains a checksum 785 of the trace records (even if space is exhausted) so that the 786 sequence of I/O accesses can be verified. 787 788 When debugging drivers it is useful to see what I/O accesses were 789 done and in what order. 790 791 Even if the individual accesses are of little interest it can be 792 useful to verify that the access pattern is consistent each time 793 an operation is performed. In this case a checksum can be used to 794 characterise the operation of a driver. The checksum can be compared 795 across different runs of the operation to verify that the driver is 796 working properly. 797 798 In particular, when performing major refactoring of the driver, where 799 the access pattern should not change, the checksum provides assurance 800 that the refactoring work has not broken the driver. 801 802 This works by sneaking into the io.h heder for an architecture and 803 redirecting I/O accesses through iotrace's tracing mechanism. 804 805 For now no commands are provided to examine the trace buffer. The 806 format is fairly simple, so 'md' is a reasonable substitute. 807 808 Note: The checksum feature is only useful for I/O regions where the 809 contents do not change outside of software control. Where this is not 810 suitable you can fall back to manually comparing the addresses. It 811 might be useful to enhance tracing to only checksum the accesses and 812 not the data read/written. 813 814config CMD_I2C 815 bool "i2c" 816 help 817 I2C support. 818 819config CMD_LOADB 820 bool "loadb" 821 default y 822 help 823 Load a binary file over serial line. 824 825config CMD_LOADS 826 bool "loads" 827 default y 828 help 829 Load an S-Record file over serial line 830 831config CMD_MMC 832 bool "mmc" 833 help 834 MMC memory mapped support. 835 836config CMD_MMC_RPMB 837 bool "Enable support for RPMB in the mmc command" 838 depends on CMD_MMC 839 help 840 Enable the commands for reading, writing and programming the 841 key for the Replay Protection Memory Block partition in eMMC. 842 843config CMD_MMC_SWRITE 844 bool "mmc swrite" 845 depends on CMD_MMC && MMC_WRITE 846 select IMAGE_SPARSE 847 help 848 Enable support for the "mmc swrite" command to write Android sparse 849 images to eMMC. 850 851config CMD_NAND 852 bool "nand" 853 default y if NAND_SUNXI 854 help 855 NAND support. 856 857if CMD_NAND 858config CMD_NAND_TRIMFFS 859 bool "nand write.trimffs" 860 default y if ARCH_SUNXI 861 help 862 Allows one to skip empty pages when flashing something on a NAND. 863 864config CMD_NAND_LOCK_UNLOCK 865 bool "nand lock/unlock" 866 help 867 NAND locking support. 868 869config CMD_NAND_TORTURE 870 bool "nand torture" 871 help 872 NAND torture support. 873 874endif # CMD_NAND 875 876config CMD_NVME 877 bool "nvme" 878 depends on NVME 879 default y if NVME 880 help 881 NVM Express device support 882 883config CMD_MMC_SPI 884 bool "mmc_spi - Set up MMC SPI device" 885 help 886 Provides a way to set up an MMC (Multimedia Card) SPI (Serial 887 Peripheral Interface) device. The device provides a means of 888 accessing an MMC device via SPI using a single data line, limited 889 to 20MHz. It is useful since it reduces the amount of protocol code 890 required. 891 892config CMD_ONENAND 893 bool "onenand - access to onenand device" 894 help 895 OneNAND is a brand of NAND ('Not AND' gate) flash which provides 896 various useful features. This command allows reading, writing, 897 and erasing blocks. It allso provides a way to show and change 898 bad blocks, and test the device. 899 900config CMD_PART 901 bool "part" 902 select PARTITION_UUIDS 903 select HAVE_BLOCK_DEVICE 904 help 905 Read and display information about the partition table on 906 various media. 907 908config CMD_PCI 909 bool "pci - Access PCI devices" 910 help 911 Provide access to PCI (Peripheral Interconnect Bus), a type of bus 912 used on some devices to allow the CPU to communicate with its 913 peripherals. Sub-commands allow bus enumeration, displaying and 914 changing configuration space and a few other features. 915 916config CMD_PCMCIA 917 bool "pinit - Set up PCMCIA device" 918 help 919 Provides a means to initialise a PCMCIA (Personal Computer Memory 920 Card International Association) device. This is an old standard from 921 about 1990. These devices are typically removable memory or network 922 cards using a standard 68-pin connector. 923 924config CMD_READ 925 bool "read - Read binary data from a partition" 926 help 927 Provides low-level access to the data in a partition. 928 929config CMD_REMOTEPROC 930 bool "remoteproc" 931 depends on REMOTEPROC 932 help 933 Support for Remote Processor control 934 935config CMD_SATA 936 bool "sata - Access SATA subsystem" 937 select SATA 938 help 939 SATA (Serial Advanced Technology Attachment) is a serial bus 940 standard for connecting to hard drives and other storage devices. 941 This command provides information about attached devices and allows 942 reading, writing and other operations. 943 944 SATA replaces PATA (originally just ATA), which stands for Parallel AT 945 Attachment, where AT refers to an IBM AT (Advanced Technology) 946 computer released in 1984. 947 948config CMD_SAVES 949 bool "saves - Save a file over serial in S-Record format" 950 help 951 Provides a way to save a binary file using the Motorola S-Record 952 format over the serial line. 953 954config CMD_SCSI 955 bool "scsi - Access to SCSI devices" 956 default y if SCSI 957 help 958 This provides a 'scsi' command which provides access to SCSI (Small 959 Computer System Interface) devices. The command provides a way to 960 scan the bus, reset the bus, read and write data and get information 961 about devices. 962 963config CMD_SDRAM 964 bool "sdram - Print SDRAM configuration information" 965 help 966 Provides information about attached SDRAM. This assumed that the 967 SDRAM has an EEPROM with information that can be read using the 968 I2C bus. This is only available on some boards. 969 970config CMD_SF 971 bool "sf" 972 help 973 SPI Flash support 974 975config CMD_SF_TEST 976 bool "sf test - Allow testing of SPI flash" 977 help 978 Provides a way to test that SPI flash is working correctly. The 979 test is destructive, in that an area of SPI flash must be provided 980 for the test to use. Performance information is also provided, 981 measuring the performance of reading, writing and erasing in 982 Mbps (Million Bits Per Second). This value should approximately 983 equal the SPI bus speed for a single-bit-wide SPI bus, assuming 984 everything is working properly. 985 986config CMD_SPI 987 bool "sspi" 988 help 989 SPI utility command. 990 991config CMD_TSI148 992 bool "tsi148 - Command to access tsi148 device" 993 help 994 This provides various sub-commands to initialise and configure the 995 Turndra tsi148 device. See the command help for full details. 996 997config CMD_UNIVERSE 998 bool "universe - Command to set up the Turndra Universe controller" 999 help 1000 This allows setting up the VMEbus provided by this controller. 1001 See the command help for full details. 1002 1003config CMD_USB 1004 bool "usb" 1005 select HAVE_BLOCK_DEVICE 1006 help 1007 USB support. 1008 1009config CMD_USB_SDP 1010 bool "sdp" 1011 select USB_FUNCTION_SDP 1012 help 1013 Enables the command "sdp" which is used to have U-Boot emulating the 1014 Serial Download Protocol (SDP) via USB. 1015config CMD_ROCKUSB 1016 bool "rockusb" 1017 depends on USB_FUNCTION_ROCKUSB 1018 help 1019 Rockusb protocol is widely used by Rockchip SoC based devices. It can 1020 read/write info, image to/from devices. This enable rockusb command 1021 support to communication with rockusb device. for more detail about 1022 this command, please read doc/README.rockusb. 1023 1024config CMD_USB_MASS_STORAGE 1025 bool "UMS usb mass storage" 1026 select USB_FUNCTION_MASS_STORAGE 1027 help 1028 USB mass storage support 1029 1030endmenu 1031 1032 1033menu "Shell scripting commands" 1034 1035config CMD_ECHO 1036 bool "echo" 1037 default y 1038 help 1039 Echo args to console 1040 1041config CMD_ITEST 1042 bool "itest" 1043 default y 1044 help 1045 Return true/false on integer compare. 1046 1047config CMD_SOURCE 1048 bool "source" 1049 default y 1050 help 1051 Run script from memory 1052 1053config CMD_SETEXPR 1054 bool "setexpr" 1055 default y 1056 help 1057 Evaluate boolean and math expressions and store the result in an env 1058 variable. 1059 Also supports loading the value at a memory location into a variable. 1060 If CONFIG_REGEX is enabled, setexpr also supports a gsub function. 1061 1062endmenu 1063 1064if NET 1065 1066menuconfig CMD_NET 1067 bool "Network commands" 1068 default y 1069 1070if CMD_NET 1071 1072config CMD_BOOTP 1073 bool "bootp" 1074 default y 1075 help 1076 bootp - boot image via network using BOOTP/TFTP protocol 1077 1078config CMD_DHCP 1079 bool "dhcp" 1080 depends on CMD_BOOTP 1081 help 1082 Boot image via network using DHCP/TFTP protocol 1083 1084config BOOTP_BOOTPATH 1085 bool "Request & store 'rootpath' from BOOTP/DHCP server" 1086 default y 1087 depends on CMD_BOOTP 1088 help 1089 Even though the config is called BOOTP_BOOTPATH, it stores the 1090 path in the variable 'rootpath'. 1091 1092config BOOTP_DNS 1093 bool "Request & store 'dnsip' from BOOTP/DHCP server" 1094 default y 1095 depends on CMD_BOOTP 1096 help 1097 The primary DNS server is stored as 'dnsip'. If two servers are 1098 returned, you must set BOOTP_DNS2 to store that second server IP 1099 also. 1100 1101config BOOTP_DNS2 1102 bool "Store 'dnsip2' from BOOTP/DHCP server" 1103 depends on BOOTP_DNS 1104 help 1105 If a DHCP client requests the DNS server IP from a DHCP server, 1106 it is possible that more than one DNS serverip is offered to the 1107 client. If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS 1108 server IP will be stored in the additional environment 1109 variable "dnsip2". The first DNS serverip is always 1110 stored in the variable "dnsip", when BOOTP_DNS is defined. 1111 1112config BOOTP_GATEWAY 1113 bool "Request & store 'gatewayip' from BOOTP/DHCP server" 1114 default y 1115 depends on CMD_BOOTP 1116 1117config BOOTP_HOSTNAME 1118 bool "Request & store 'hostname' from BOOTP/DHCP server" 1119 default y 1120 depends on CMD_BOOTP 1121 help 1122 The name may or may not be qualified with the local domain name. 1123 1124config BOOTP_SUBNETMASK 1125 bool "Request & store 'netmask' from BOOTP/DHCP server" 1126 default y 1127 depends on CMD_BOOTP 1128 1129config BOOTP_NTPSERVER 1130 bool "Request & store 'ntpserverip' from BOOTP/DHCP server" 1131 depends on CMD_BOOTP 1132 1133config BOOTP_PXE 1134 bool "Send PXE client arch to BOOTP/DHCP server" 1135 default y 1136 depends on CMD_BOOTP && CMD_PXE 1137 help 1138 Supported for ARM, ARM64, and x86 for now. 1139 1140config BOOTP_PXE_CLIENTARCH 1141 hex 1142 depends on BOOTP_PXE 1143 default 0x16 if ARM64 1144 default 0x15 if ARM 1145 default 0 if X86 1146 1147config BOOTP_VCI_STRING 1148 string 1149 depends on CMD_BOOTP 1150 default "U-Boot.armv7" if CPU_V7A || CPU_V7M || CPU_V7R 1151 default "U-Boot.armv8" if ARM64 1152 default "U-Boot.arm" if ARM 1153 default "U-Boot" 1154 1155config CMD_TFTPBOOT 1156 bool "tftpboot" 1157 default y 1158 help 1159 tftpboot - boot image via network using TFTP protocol 1160 1161config CMD_TFTPPUT 1162 bool "tftp put" 1163 depends on CMD_TFTPBOOT 1164 help 1165 TFTP put command, for uploading files to a server 1166 1167config CMD_TFTPSRV 1168 bool "tftpsrv" 1169 depends on CMD_TFTPBOOT 1170 help 1171 Act as a TFTP server and boot the first received file 1172 1173config NET_TFTP_VARS 1174 bool "Control TFTP timeout and count through environment" 1175 depends on CMD_TFTPBOOT 1176 default y 1177 help 1178 If set, allows controlling the TFTP timeout through the 1179 environment variable tftptimeout, and the TFTP maximum 1180 timeout count through the variable tftptimeoutcountmax. 1181 If unset, timeout and maximum are hard-defined as 1 second 1182 and 10 timouts per TFTP transfer. 1183 1184config CMD_RARP 1185 bool "rarpboot" 1186 help 1187 Boot image via network using RARP/TFTP protocol 1188 1189config CMD_NFS 1190 bool "nfs" 1191 default y 1192 help 1193 Boot image via network using NFS protocol. 1194 1195config CMD_MII 1196 bool "mii" 1197 help 1198 Enable MII utility commands. 1199 1200config CMD_PING 1201 bool "ping" 1202 help 1203 Send ICMP ECHO_REQUEST to network host 1204 1205config CMD_CDP 1206 bool "cdp" 1207 help 1208 Perform CDP network configuration 1209 1210config CMD_SNTP 1211 bool "sntp" 1212 help 1213 Synchronize RTC via network 1214 1215config CMD_DNS 1216 bool "dns" 1217 help 1218 Lookup the IP of a hostname 1219 1220config CMD_LINK_LOCAL 1221 bool "linklocal" 1222 help 1223 Acquire a network IP address using the link-local protocol 1224 1225endif 1226 1227config CMD_ETHSW 1228 bool "ethsw" 1229 help 1230 Allow control of L2 Ethernet switch commands. These are supported 1231 by the vsc9953 Ethernet driver at present. Sub-commands allow 1232 operations such as enabling / disabling a port and 1233 viewing/maintaining the filtering database (FDB) 1234 1235config CMD_PXE 1236 bool "pxe" 1237 select MENU 1238 help 1239 Boot image via network using PXE protocol 1240 1241endif 1242 1243menu "Misc commands" 1244 1245config CMD_BMP 1246 bool "Enable 'bmp' command" 1247 depends on LCD || DM_VIDEO || VIDEO 1248 help 1249 This provides a way to obtain information about a BMP-format iamge 1250 and to display it. BMP (which presumably stands for BitMaP) is a 1251 file format defined by Microsoft which supports images of various 1252 depths, formats and compression methods. Headers on the file 1253 determine the formats used. This command can be used by first loading 1254 the image into RAM, then using this command to look at it or display 1255 it. 1256 1257config CMD_BOOTCOUNT 1258 bool "bootcount" 1259 depends on BOOTCOUNT_LIMIT 1260 help 1261 Enable the bootcount command, which allows interrogation and 1262 reset of the bootcounter. 1263 1264config CMD_BSP 1265 bool "Enable board-specific commands" 1266 help 1267 (deprecated: instead, please define a Kconfig option for each command) 1268 1269 Some boards have board-specific commands which are only enabled 1270 during developemnt and need to be turned off for production. This 1271 option provides a way to control this. The commands that are enabled 1272 vary depending on the board. 1273 1274config CMD_BKOPS_ENABLE 1275 bool "mmc bkops enable" 1276 depends on CMD_MMC 1277 default n 1278 help 1279 Enable command for setting manual background operations handshake 1280 on a eMMC device. The feature is optionally available on eMMC devices 1281 conforming to standard >= 4.41. 1282 1283config CMD_BLOCK_CACHE 1284 bool "blkcache - control and stats for block cache" 1285 depends on BLOCK_CACHE 1286 default y if BLOCK_CACHE 1287 help 1288 Enable the blkcache command, which can be used to control the 1289 operation of the cache functions. 1290 This is most useful when fine-tuning the operation of the cache 1291 during development, but also allows the cache to be disabled when 1292 it might hurt performance (e.g. when using the ums command). 1293 1294config CMD_CACHE 1295 bool "icache or dcache" 1296 help 1297 Enable the "icache" and "dcache" commands 1298 1299config CMD_DISPLAY 1300 bool "Enable the 'display' command, for character displays" 1301 help 1302 (this needs porting to driver model) 1303 This enables the 'display' command which allows a string to be 1304 displayed on a simple board-specific display. Implement 1305 display_putc() to use it. 1306 1307config CMD_LED 1308 bool "led" 1309 default y if LED 1310 help 1311 Enable the 'led' command which allows for control of LEDs supported 1312 by the board. The LEDs can be listed with 'led list' and controlled 1313 with led on/off/togle/blink. Any LED drivers can be controlled with 1314 this command, e.g. led_gpio. 1315 1316config CMD_DATE 1317 bool "date" 1318 default y if DM_RTC 1319 help 1320 Enable the 'date' command for getting/setting the time/date in RTC 1321 devices. 1322 1323config CMD_TIME 1324 bool "time" 1325 help 1326 Run commands and summarize execution time. 1327 1328config CMD_GETTIME 1329 bool "gettime - read elapsed time" 1330 help 1331 Enable the 'gettime' command which reads the elapsed time since 1332 U-Boot started running. This shows the time in seconds and 1333 milliseconds. See also the 'bootstage' command which provides more 1334 flexibility for boot timing. 1335 1336# TODO: rename to CMD_SLEEP 1337config CMD_MISC 1338 bool "sleep" 1339 default y 1340 help 1341 Delay execution for some time 1342 1343config CMD_TIMER 1344 bool "timer" 1345 help 1346 Access the system timer. 1347 1348config CMD_SOUND 1349 bool "sound" 1350 depends on SOUND 1351 help 1352 This provides basic access to the U-Boot's sound support. The main 1353 feature is to play a beep. 1354 1355 sound init - set up sound system 1356 sound play - play a sound 1357 1358config CMD_QFW 1359 bool "qfw" 1360 select QFW 1361 help 1362 This provides access to the QEMU firmware interface. The main 1363 feature is to allow easy loading of files passed to qemu-system 1364 via -kernel / -initrd 1365 1366source "cmd/mvebu/Kconfig" 1367 1368config CMD_TERMINAL 1369 bool "terminal - provides a way to attach a serial terminal" 1370 help 1371 Provides a 'cu'-like serial terminal command. This can be used to 1372 access other serial ports from the system console. The terminal 1373 is very simple with no special processing of characters. As with 1374 cu, you can press ~. (tilde followed by period) to exit. 1375 1376config CMD_UUID 1377 bool "uuid, guid - generation of unique IDs" 1378 select LIB_UUID 1379 help 1380 This enables two commands: 1381 1382 uuid - generate random Universally Unique Identifier 1383 guid - generate Globally Unique Identifier based on random UUID 1384 1385 The two commands are very similar except for the endianness of the 1386 output. 1387 1388endmenu 1389 1390source "cmd/ti/Kconfig" 1391 1392config CMD_BOOTSTAGE 1393 bool "Enable the 'bootstage' command" 1394 depends on BOOTSTAGE 1395 help 1396 Add a 'bootstage' command which supports printing a report 1397 and un/stashing of bootstage data. 1398 1399menu "Power commands" 1400config CMD_PMIC 1401 bool "Enable Driver Model PMIC command" 1402 depends on DM_PMIC 1403 help 1404 This is the pmic command, based on a driver model pmic's API. 1405 Command features are unchanged: 1406 - list - list pmic devices 1407 - pmic dev <id> - show or [set] operating pmic device (NEW) 1408 - pmic dump - dump registers 1409 - pmic read address - read byte of register at address 1410 - pmic write address - write byte to register at address 1411 The only one change for this command is 'dev' subcommand. 1412 1413config CMD_REGULATOR 1414 bool "Enable Driver Model REGULATOR command" 1415 depends on DM_REGULATOR 1416 help 1417 This command is based on driver model regulator's API. 1418 User interface features: 1419 - list - list regulator devices 1420 - regulator dev <id> - show or [set] operating regulator device 1421 - regulator info - print constraints info 1422 - regulator status - print operating status 1423 - regulator value <val] <-f> - print/[set] voltage value [uV] 1424 - regulator current <val> - print/[set] current value [uA] 1425 - regulator mode <id> - print/[set] operating mode id 1426 - regulator enable - enable the regulator output 1427 - regulator disable - disable the regulator output 1428 1429 The '-f' (force) option can be used for set the value which exceeds 1430 the limits, which are found in device-tree and are kept in regulator's 1431 uclass platdata structure. 1432 1433endmenu 1434 1435menu "Security commands" 1436config CMD_AES 1437 bool "Enable the 'aes' command" 1438 select AES 1439 help 1440 This provides a means to encrypt and decrypt data using the AES 1441 (Advanced Encryption Standard). This algorithm uses a symetric key 1442 and is widely used as a streaming cipher. Different key lengths are 1443 supported by the algorithm but this command only supports 128 bits 1444 at present. 1445 1446config CMD_BLOB 1447 bool "Enable the 'blob' command" 1448 help 1449 This is used with the Freescale secure boot mechanism. 1450 1451 Freescale's SEC block has built-in Blob Protocol which provides 1452 a method for protecting user-defined data across system power 1453 cycles. SEC block protects data in a data structure called a Blob, 1454 which provides both confidentiality and integrity protection. 1455 1456 Encapsulating data as a blob 1457 Each time that the Blob Protocol is used to protect data, a 1458 different randomly generated key is used to encrypt the data. 1459 This random key is itself encrypted using a key which is derived 1460 from SoC's non-volatile secret key and a 16 bit Key identifier. 1461 The resulting encrypted key along with encrypted data is called a 1462 blob. The non-volatile secure key is available for use only during 1463 secure boot. 1464 1465 During decapsulation, the reverse process is performed to get back 1466 the original data. 1467 1468 Sub-commands: 1469 blob enc - encapsulating data as a cryptgraphic blob 1470 blob dec - decapsulating cryptgraphic blob to get the data 1471 1472 Syntax: 1473 1474 blob enc src dst len km 1475 1476 Encapsulate and create blob of data $len bytes long 1477 at address $src and store the result at address $dst. 1478 $km is the 16 byte key modifier is also required for 1479 generation/use as key for cryptographic operation. Key 1480 modifier should be 16 byte long. 1481 1482 blob dec src dst len km 1483 1484 Decapsulate the blob of data at address $src and 1485 store result of $len byte at addr $dst. 1486 $km is the 16 byte key modifier is also required for 1487 generation/use as key for cryptographic operation. Key 1488 modifier should be 16 byte long. 1489 1490config CMD_HASH 1491 bool "Support 'hash' command" 1492 select HASH 1493 help 1494 This provides a way to hash data in memory using various supported 1495 algorithms (such as SHA1, MD5, CRC32). The computed digest can be 1496 saved to memory or to an environment variable. It is also possible 1497 to verify a hash against data in memory. 1498 1499config CMD_HVC 1500 bool "Support the 'hvc' command" 1501 depends on ARM_SMCCC 1502 help 1503 Allows issuing Hypervisor Calls (HVCs). Mostly useful for 1504 development and testing. 1505 1506config CMD_SMC 1507 bool "Support the 'smc' command" 1508 depends on ARM_SMCCC 1509 help 1510 Allows issuing Secure Monitor Calls (SMCs). Mostly useful for 1511 development and testing. 1512 1513config HASH_VERIFY 1514 bool "hash -v" 1515 depends on CMD_HASH 1516 help 1517 Add -v option to verify data against a hash. 1518 1519config CMD_TPM_V1 1520 bool 1521 1522config CMD_TPM_V2 1523 bool 1524 1525config CMD_TPM 1526 bool "Enable the 'tpm' command" 1527 depends on TPM_V1 || TPM_V2 1528 select CMD_TPM_V1 if TPM_V1 1529 select CMD_TPM_V2 if TPM_V2 1530 help 1531 This provides a means to talk to a TPM from the command line. A wide 1532 range of commands if provided - see 'tpm help' for details. The 1533 command requires a suitable TPM on your board and the correct driver 1534 must be enabled. 1535 1536if CMD_TPM 1537 1538config CMD_TPM_TEST 1539 bool "Enable the 'tpm test' command" 1540 depends on TPM_V1 1541 help 1542 This provides a a series of tests to confirm that the TPMv1.x is 1543 working correctly. The tests cover initialisation, non-volatile RAM, 1544 extend, global lock and checking that timing is within expectations. 1545 The tests pass correctly on Infineon TPMs but may need to be adjusted 1546 for other devices. 1547 1548endif 1549 1550endmenu 1551 1552menu "Firmware commands" 1553config CMD_CROS_EC 1554 bool "Enable crosec command" 1555 depends on CROS_EC 1556 default y 1557 help 1558 Enable command-line access to the Chrome OS EC (Embedded 1559 Controller). This provides the 'crosec' command which has 1560 a number of sub-commands for performing EC tasks such as 1561 updating its flash, accessing a small saved context area 1562 and talking to the I2C bus behind the EC (if there is one). 1563endmenu 1564 1565menu "Filesystem commands" 1566config CMD_BTRFS 1567 bool "Enable the 'btrsubvol' command" 1568 select FS_BTRFS 1569 help 1570 This enables the 'btrsubvol' command to list subvolumes 1571 of a BTRFS filesystem. There are no special commands for 1572 listing BTRFS directories or loading BTRFS files - this 1573 can be done by the generic 'fs' commands (see CMD_FS_GENERIC) 1574 when BTRFS is enabled (see FS_BTRFS). 1575 1576config CMD_CBFS 1577 bool "Enable the 'cbfs' command" 1578 depends on FS_CBFS 1579 help 1580 Define this to enable support for reading from a Coreboot 1581 filesystem. This is a ROM-based filesystem used for accessing files 1582 on systems that use coreboot as the first boot-loader and then load 1583 U-Boot to actually boot the Operating System. Available commands are 1584 cbfsinit, cbfsinfo, cbfsls and cbfsload. 1585 1586config CMD_CRAMFS 1587 bool "Enable the 'cramfs' command" 1588 depends on FS_CRAMFS 1589 help 1590 This provides commands for dealing with CRAMFS (Compressed ROM 1591 filesystem). CRAMFS is useful when space is tight since files are 1592 compressed. Two commands are provided: 1593 1594 cramfsls - lists files in a cramfs image 1595 cramfsload - loads a file from a cramfs image 1596 1597config CMD_EXT2 1598 bool "ext2 command support" 1599 select FS_EXT4 1600 help 1601 Enables EXT2 FS command 1602 1603config CMD_EXT4 1604 bool "ext4 command support" 1605 select FS_EXT4 1606 help 1607 Enables EXT4 FS command 1608 1609config CMD_EXT4_WRITE 1610 depends on CMD_EXT4 1611 bool "ext4 write command support" 1612 select EXT4_WRITE 1613 help 1614 Enables EXT4 FS write command 1615 1616config CMD_FAT 1617 bool "FAT command support" 1618 select FS_FAT 1619 help 1620 Support for the FAT fs 1621 1622config CMD_FS_GENERIC 1623 bool "filesystem commands" 1624 help 1625 Enables filesystem commands (e.g. load, ls) that work for multiple 1626 fs types. 1627 1628config CMD_FS_UUID 1629 bool "fsuuid command" 1630 help 1631 Enables fsuuid command for filesystem UUID. 1632 1633config CMD_JFFS2 1634 bool "jffs2 command" 1635 select FS_JFFS2 1636 help 1637 Enables commands to support the JFFS2 (Journalling Flash File System 1638 version 2) filesystem. This enables fsload, ls and fsinfo which 1639 provide the ability to load files, list directories and obtain 1640 filesystem information. 1641 1642config CMD_MTDPARTS 1643 bool "MTD partition support" 1644 help 1645 MTD partition support 1646 1647config MTDIDS_DEFAULT 1648 string "Default MTD IDs" 1649 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH 1650 help 1651 Defines a default MTD IDs list for use with MTD partitions in the 1652 Linux MTD command line partitions format. 1653 1654config MTDPARTS_DEFAULT 1655 string "Default MTD partition scheme" 1656 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH 1657 help 1658 Defines a default MTD partitioning scheme in the Linux MTD command 1659 line partitions format 1660 1661config CMD_MTDPARTS_SPREAD 1662 bool "Padd partition size to take account of bad blocks" 1663 depends on CMD_MTDPARTS 1664 help 1665 This enables the 'spread' sub-command of the mtdparts command. 1666 This command will modify the existing mtdparts variable by increasing 1667 the size of the partitions such that 1) each partition's net size is 1668 at least as large as the size specified in the mtdparts variable and 1669 2) each partition starts on a good block. 1670 1671config CMD_REISER 1672 bool "reiser - Access to reiserfs filesystems" 1673 help 1674 This provides two commands which operate on a resierfs filesystem, 1675 commonly used some years ago: 1676 1677 reiserls - list files 1678 reiserload - load a file 1679 1680config CMD_YAFFS2 1681 bool "yaffs2 - Access of YAFFS2 filesystem" 1682 depends on YAFFS2 1683 default y 1684 help 1685 This provides commands for accessing a YAFFS2 filesystem. Yet 1686 Another Flash Filesystem 2 is a filesystem designed specifically 1687 for NAND flash. It incorporates bad-block management and ensures 1688 that device writes are sequential regardless of filesystem 1689 activity. 1690 1691config CMD_ZFS 1692 bool "zfs - Access of ZFS filesystem" 1693 help 1694 This provides commands to accessing a ZFS filesystem, commonly used 1695 on Solaris systems. Two sub-commands are provided: 1696 1697 zfsls - list files in a directory 1698 zfsload - load a file 1699 1700 See doc/README.zfs for more details. 1701 1702endmenu 1703 1704menu "Debug commands" 1705 1706config CMD_BEDBUG 1707 bool "bedbug" 1708 help 1709 The bedbug (emBEDded deBUGger) command provides debugging features 1710 for some PowerPC processors. For details please see the 1711 docuemntation in doc/README.beddbug 1712 1713config CMD_DIAG 1714 bool "diag - Board diagnostics" 1715 help 1716 This command provides access to board diagnostic tests. These are 1717 called Power-on Self Tests (POST). The command allows listing of 1718 available tests and running either all the tests, or specific tests 1719 identified by name. 1720 1721config CMD_IRQ 1722 bool "irq - Show information about interrupts" 1723 depends on !ARM && !MIPS && !SH 1724 help 1725 This enables two commands: 1726 1727 interrupts - enable or disable interrupts 1728 irqinfo - print device-specific interrupt information 1729 1730config CMD_KGDB 1731 bool "kgdb - Allow debugging of U-Boot with gdb" 1732 help 1733 This enables a 'kgdb' command which allows gdb to connect to U-Boot 1734 over a serial link for debugging purposes. This allows 1735 single-stepping, inspecting variables, etc. This is supported only 1736 on PowerPC at present. 1737 1738config CMD_LOG 1739 bool "log - Generation, control and access to logging" 1740 select LOG 1741 help 1742 This provides access to logging features. It allows the output of 1743 log data to be controlled to a limited extent (setting up the default 1744 maximum log level for emitting of records). It also provides access 1745 to a command used for testing the log system. 1746 1747config CMD_TRACE 1748 bool "trace - Support tracing of function calls and timing" 1749 help 1750 Enables a command to control using of function tracing within 1751 U-Boot. This allows recording of call traces including timing 1752 information. The command can write data to memory for exporting 1753 for analsys (e.g. using bootchart). See doc/README.trace for full 1754 details. 1755 1756endmenu 1757 1758config CMD_UBI 1759 tristate "Enable UBI - Unsorted block images commands" 1760 select CRC32 1761 select MTD_UBI 1762 select CMD_MTDPARTS 1763 default y if NAND_SUNXI 1764 help 1765 UBI is a software layer above MTD layer which admits use of LVM-like 1766 logical volumes on top of MTD devices, hides some complexities of 1767 flash chips like wear and bad blocks and provides some other useful 1768 capabilities. Please, consult the MTD web site for more details 1769 (www.linux-mtd.infradead.org). Activate this option if you want 1770 to use U-Boot UBI commands. 1771 1772config CMD_UBIFS 1773 tristate "Enable UBIFS - Unsorted block images filesystem commands" 1774 depends on CMD_UBI 1775 select CRC32 1776 select LZO 1777 default y if CMD_UBI 1778 help 1779 UBIFS is a file system for flash devices which works on top of UBI. 1780 1781endmenu 1782