1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #include <common.h> 9 #include <i2c.h> 10 11 #include <fsl_ddr_sdram.h> 12 #include <fsl_ddr_dimm_params.h> 13 14 void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address) 15 { 16 i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, 17 sizeof(ddr2_spd_eeprom_t)); 18 } 19 20 /* 21 * There are four board-specific SDRAM timing parameters which must be 22 * calculated based on the particular PCB artwork. These are: 23 * 1.) CPO (Read Capture Delay) 24 * - TIMING_CFG_2 register 25 * Source: Calculation based on board trace lengths and 26 * chip-specific internal delays. 27 * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) 28 * - TIMING_CFG_2 register 29 * Source: Calculation based on board trace lengths. 30 * Unless clock and DQ lanes are very different 31 * lengths (>2"), this should be set to the nominal value 32 * of 1/2 clock delay. 33 * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) 34 * - DDR_SDRAM_CLK_CNTL register 35 * Source: Signal Integrity Simulations 36 * 4.) 2T Timing on Addr/Ctl 37 * - TIMING_CFG_2 register 38 * Source: Signal Integrity Simulations 39 * Usually only needed with heavy load/very high speed (>DDR2-800) 40 * 41 * ====== XPedite5370 DDR2-600 read delay calculations ====== 42 * 43 * See Freescale's App Note AN2583 as refrence. This document also 44 * contains the chip-specific delays for 8548E, 8572, etc. 45 * 46 * For MPC8572E 47 * Minimum chip delay (Ch 0): 1.372ns 48 * Maximum chip delay (Ch 0): 2.914ns 49 * Minimum chip delay (Ch 1): 1.220ns 50 * Maximum chip delay (Ch 1): 2.595ns 51 * 52 * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps 53 * 54 * Minimum delay calc (Ch 0): 55 * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly 56 * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps 57 * = 3808ps 58 * = 3.808ns 59 * 60 * Maximum delay calc (Ch 0): 61 * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly 62 * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps 63 * = 6240ps 64 * = 6.240ns 65 * 66 * Minimum delay calc (Ch 1): 67 * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly 68 * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps 69 * = 3288ps 70 * = 3.288ns 71 * 72 * Maximum delay calc (Ch 1): 73 * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly 74 * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps 75 * = 5536ps 76 * = 5.536ns 77 * 78 * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target) 79 * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) 80 * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target) 81 * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7) 82 * 83 * 84 * ====== XPedite5370 DDR2-800 read delay calculations ====== 85 * 86 * See Freescale's App Note AN2583 as refrence. This document also 87 * contains the chip-specific delays for 8548E, 8572, etc. 88 * 89 * For MPC8572E 90 * Minimum chip delay (Ch 0): 1.372ns 91 * Maximum chip delay (Ch 0): 2.914ns 92 * Minimum chip delay (Ch 1): 1.220ns 93 * Maximum chip delay (Ch 1): 2.595ns 94 * 95 * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps 96 * 97 * Minimum delay calc (Ch 0): 98 * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly 99 * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps 100 * = 3341ps 101 * = 3.341ns 102 * 103 * Maximum delay calc (Ch 0): 104 * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly 105 * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps 106 * = 5673ps 107 * = 5.673ns 108 * 109 * Minimum delay calc (Ch 1): 110 * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly 111 * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps 112 * = 2822ps 113 * = 2.822ns 114 * 115 * Maximum delay calc (Ch 1): 116 * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly 117 * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps 118 * = 4968ps 119 * = 4.968ns 120 * 121 * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target) 122 * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9) 123 * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target) 124 * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) 125 * 126 * Write latency (WR_DATA_DELAY) is calculated by doing the following: 127 * 128 * The DDR SDRAM specification requires DQS be received no sooner than 129 * 75% of an SDRAM clock period—and no later than 125% of a clock 130 * period—from the capturing clock edge of the command/address at the 131 * SDRAM. 132 * 133 * Based on the above tracelengths, the following are calculated: 134 * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns 135 * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns 136 * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns 137 * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns 138 * 139 * Difference in arrival time CLK vs. DQS: 140 * Ch. 0 0.072ns 141 * Ch. 1 0.138ns 142 * 143 * Both of these values are much less than 25% of the clock 144 * period at DDR2-600 or DDR2-800, so no additional delay is needed over 145 * the 1/2 cycle which normally aligns the first DQS transition 146 * exactly WL (CAS latency minus one cycle) after the CAS strobe. 147 * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's 148 * terminology corresponds to exactly one clock period delay after 149 * the CAS strobe. (due to the fact that the "delay" is referenced 150 * from the *falling* edge of the CLK, just after the rising edge 151 * which the CAS strobe is latched on. 152 */ 153 154 typedef struct board_memctl_options { 155 uint16_t datarate_mhz_low; 156 uint16_t datarate_mhz_high; 157 uint8_t clk_adjust; 158 uint8_t cpo_override; 159 uint8_t write_data_delay; 160 } board_memctl_options_t; 161 162 static struct board_memctl_options bopts_ctrl[][2] = { 163 { 164 /* Controller 0 */ 165 { 166 /* DDR2 600/667 */ 167 .datarate_mhz_low = 500, 168 .datarate_mhz_high = 750, 169 .clk_adjust = 5, 170 .cpo_override = 8, 171 .write_data_delay = 2, 172 }, 173 { 174 /* DDR2 800 */ 175 .datarate_mhz_low = 750, 176 .datarate_mhz_high = 850, 177 .clk_adjust = 5, 178 .cpo_override = 9, 179 .write_data_delay = 2, 180 }, 181 }, 182 { 183 /* Controller 1 */ 184 { 185 /* DDR2 600/667 */ 186 .datarate_mhz_low = 500, 187 .datarate_mhz_high = 750, 188 .clk_adjust = 5, 189 .cpo_override = 7, 190 .write_data_delay = 2, 191 }, 192 { 193 /* DDR2 800 */ 194 .datarate_mhz_low = 750, 195 .datarate_mhz_high = 850, 196 .clk_adjust = 5, 197 .cpo_override = 8, 198 .write_data_delay = 2, 199 }, 200 }, 201 }; 202 203 void fsl_ddr_board_options(memctl_options_t *popts, 204 dimm_params_t *pdimm, 205 unsigned int ctrl_num) 206 { 207 struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; 208 sys_info_t sysinfo; 209 int i; 210 unsigned int datarate; 211 212 get_sys_info(&sysinfo); 213 datarate = sysinfo.freq_ddrbus / 1000 / 1000; 214 215 for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { 216 if ((bopts[i].datarate_mhz_low <= datarate) && 217 (bopts[i].datarate_mhz_high >= datarate)) { 218 debug("controller %d:\n", ctrl_num); 219 debug(" clk_adjust = %d\n", bopts[i].clk_adjust); 220 debug(" cpo = %d\n", bopts[i].cpo_override); 221 debug(" write_data_delay = %d\n", 222 bopts[i].write_data_delay); 223 popts->clk_adjust = bopts[i].clk_adjust; 224 popts->cpo_override = bopts[i].cpo_override; 225 popts->write_data_delay = bopts[i].write_data_delay; 226 } 227 } 228 229 /* 230 * Factors to consider for half-strength driver enable: 231 * - number of DIMMs installed 232 */ 233 popts->half_strength_driver_enable = 0; 234 } 235