1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2016 NXP Semiconductors 4 * Author: Fabio Estevam <fabio.estevam@nxp.com> 5 */ 6 7 #include <asm/arch/clock.h> 8 #include <asm/arch/imx-regs.h> 9 #include <asm/arch/mx7-pins.h> 10 #include <asm/arch/sys_proto.h> 11 #include <asm/gpio.h> 12 #include <asm/mach-imx/hab.h> 13 #include <asm/mach-imx/iomux-v3.h> 14 #include <asm/mach-imx/mxc_i2c.h> 15 #include <asm/io.h> 16 #include <common.h> 17 #include <fsl_esdhc.h> 18 #include <i2c.h> 19 #include <mmc.h> 20 #include <asm/arch/crm_regs.h> 21 #include <usb.h> 22 #include <netdev.h> 23 #include <power/pmic.h> 24 #include <power/pfuze3000_pmic.h> 25 #include "../freescale/common/pfuze.h" 26 #include <asm/setup.h> 27 #include <asm/bootm.h> 28 29 DECLARE_GLOBAL_DATA_PTR; 30 31 #define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU100KOHM | \ 32 PAD_CTL_HYS) 33 34 int dram_init(void) 35 { 36 gd->ram_size = PHYS_SDRAM_SIZE; 37 38 /* Subtract the defined OPTEE runtime firmware length */ 39 #ifdef CONFIG_OPTEE_TZDRAM_SIZE 40 gd->ram_size -= CONFIG_OPTEE_TZDRAM_SIZE; 41 #endif 42 43 return 0; 44 } 45 46 static iomux_v3_cfg_t const wdog_pads[] = { 47 MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL), 48 }; 49 50 static iomux_v3_cfg_t const uart1_pads[] = { 51 MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), 52 MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), 53 }; 54 55 static void setup_iomux_uart(void) 56 { 57 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); 58 }; 59 60 int board_early_init_f(void) 61 { 62 setup_iomux_uart(); 63 64 return 0; 65 } 66 67 #ifdef CONFIG_DM_PMIC 68 int power_init_board(void) 69 { 70 struct udevice *dev; 71 int ret, dev_id, rev_id; 72 73 ret = pmic_get("pfuze3000", &dev); 74 if (ret == -ENODEV) 75 return 0; 76 if (ret != 0) 77 return ret; 78 79 dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID); 80 rev_id = pmic_reg_read(dev, PFUZE3000_REVID); 81 printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id); 82 83 /* disable Low Power Mode during standby mode */ 84 pmic_clrsetbits(dev, PFUZE3000_LDOGCTL, 0, 1); 85 86 return 0; 87 } 88 #endif 89 90 int board_eth_init(bd_t *bis) 91 { 92 int ret = 0; 93 94 #ifdef CONFIG_USB_ETHER 95 ret = usb_eth_initialize(bis); 96 if (ret < 0) 97 printf("Error %d registering USB ether.\n", ret); 98 #endif 99 100 return ret; 101 } 102 103 int board_init(void) 104 { 105 /* address of boot parameters */ 106 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 107 108 return 0; 109 } 110 111 int checkboard(void) 112 { 113 char *mode; 114 115 if (IS_ENABLED(CONFIG_ARMV7_BOOT_SEC_DEFAULT)) 116 mode = "secure"; 117 else 118 mode = "non-secure"; 119 120 #ifdef CONFIG_OPTEE_TZDRAM_SIZE 121 unsigned long optee_start, optee_end; 122 123 optee_end = PHYS_SDRAM + PHYS_SDRAM_SIZE; 124 optee_start = optee_end - CONFIG_OPTEE_TZDRAM_SIZE; 125 126 printf("Board: WARP7 in %s mode OPTEE DRAM 0x%08lx-0x%08lx\n", 127 mode, optee_start, optee_end); 128 #else 129 printf("Board: WARP7 in %s mode\n", mode); 130 #endif 131 132 return 0; 133 } 134 135 int board_usb_phy_mode(int port) 136 { 137 return USB_INIT_DEVICE; 138 } 139 140 int board_late_init(void) 141 { 142 struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR; 143 #ifdef CONFIG_SERIAL_TAG 144 struct tag_serialnr serialnr; 145 char serial_string[0x20]; 146 #endif 147 148 imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads)); 149 150 set_wdog_reset(wdog); 151 152 /* 153 * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4), 154 * since we use PMIC_PWRON to reset the board. 155 */ 156 clrsetbits_le16(&wdog->wcr, 0, 0x10); 157 158 #ifdef CONFIG_SECURE_BOOT 159 /* Determine HAB state */ 160 env_set_ulong(HAB_ENABLED_ENVNAME, imx_hab_is_enabled()); 161 #else 162 env_set_ulong(HAB_ENABLED_ENVNAME, 0); 163 #endif 164 165 #ifdef CONFIG_SERIAL_TAG 166 /* Set serial# standard environment variable based on OTP settings */ 167 get_board_serial(&serialnr); 168 snprintf(serial_string, sizeof(serial_string), "WaRP7-0x%08x%08x", 169 serialnr.low, serialnr.high); 170 env_set("serial#", serial_string); 171 #endif 172 173 return 0; 174 } 175