1 /* 2 * board.c 3 * 4 * Board functions for TI AM335X based boards 5 * 6 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <errno.h> 13 #include <spl.h> 14 #include <asm/arch/cpu.h> 15 #include <asm/arch/hardware.h> 16 #include <asm/arch/omap.h> 17 #include <asm/arch/ddr_defs.h> 18 #include <asm/arch/clock.h> 19 #include <asm/arch/gpio.h> 20 #include <asm/arch/mmc_host_def.h> 21 #include <asm/arch/sys_proto.h> 22 #include <asm/arch/mem.h> 23 #include <asm/arch/mux.h> 24 #include <asm/io.h> 25 #include <asm/emif.h> 26 #include <asm/gpio.h> 27 #include <i2c.h> 28 #include <miiphy.h> 29 #include <cpsw.h> 30 #include <power/tps65217.h> 31 #include <power/tps65910.h> 32 #include <environment.h> 33 #include <watchdog.h> 34 #include "board.h" 35 36 DECLARE_GLOBAL_DATA_PTR; 37 38 /* GPIO that controls power to DDR on EVM-SK */ 39 #define GPIO_DDR_VTT_EN 7 40 #define DIP_S1 44 41 42 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 43 44 static int baltos_set_console(void) 45 { 46 int val, i, dips = 0; 47 char buf[7]; 48 49 for (i = 0; i < 4; i++) { 50 sprintf(buf, "dip_s%d", i + 1); 51 52 if (gpio_request(DIP_S1 + i, buf)) { 53 printf("failed to export GPIO %d\n", DIP_S1 + i); 54 return 0; 55 } 56 57 if (gpio_direction_input(DIP_S1 + i)) { 58 printf("failed to set GPIO %d direction\n", DIP_S1 + i); 59 return 0; 60 } 61 62 val = gpio_get_value(DIP_S1 + i); 63 dips |= val << i; 64 } 65 66 printf("DIPs: 0x%1x\n", (~dips) & 0xf); 67 68 if ((dips & 0xf) == 0xe) 69 setenv("console", "ttyUSB0,115200n8"); 70 71 return 0; 72 } 73 74 static int read_eeprom(BSP_VS_HWPARAM *header) 75 { 76 i2c_set_bus_num(1); 77 78 /* Check if baseboard eeprom is available */ 79 if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) { 80 puts("Could not probe the EEPROM; something fundamentally " 81 "wrong on the I2C bus.\n"); 82 return -ENODEV; 83 } 84 85 /* read the eeprom using i2c */ 86 if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header, 87 sizeof(BSP_VS_HWPARAM))) { 88 puts("Could not read the EEPROM; something fundamentally" 89 " wrong on the I2C bus.\n"); 90 return -EIO; 91 } 92 93 if (header->Magic != 0xDEADBEEF) { 94 95 printf("Incorrect magic number (0x%x) in EEPROM\n", 96 header->Magic); 97 98 /* fill default values */ 99 header->SystemId = 211; 100 header->MAC1[0] = 0x00; 101 header->MAC1[1] = 0x00; 102 header->MAC1[2] = 0x00; 103 header->MAC1[3] = 0x00; 104 header->MAC1[4] = 0x00; 105 header->MAC1[5] = 0x01; 106 107 header->MAC2[0] = 0x00; 108 header->MAC2[1] = 0x00; 109 header->MAC2[2] = 0x00; 110 header->MAC2[3] = 0x00; 111 header->MAC2[4] = 0x00; 112 header->MAC2[5] = 0x02; 113 114 header->MAC3[0] = 0x00; 115 header->MAC3[1] = 0x00; 116 header->MAC3[2] = 0x00; 117 header->MAC3[3] = 0x00; 118 header->MAC3[4] = 0x00; 119 header->MAC3[5] = 0x03; 120 } 121 122 return 0; 123 } 124 125 #if defined(CONFIG_SPL_BUILD) || defined(CONFIG_NOR_BOOT) 126 127 static const struct ddr_data ddr3_baltos_data = { 128 .datardsratio0 = MT41K256M16HA125E_RD_DQS, 129 .datawdsratio0 = MT41K256M16HA125E_WR_DQS, 130 .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE, 131 .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA, 132 }; 133 134 static const struct cmd_control ddr3_baltos_cmd_ctrl_data = { 135 .cmd0csratio = MT41K256M16HA125E_RATIO, 136 .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 137 138 .cmd1csratio = MT41K256M16HA125E_RATIO, 139 .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 140 141 .cmd2csratio = MT41K256M16HA125E_RATIO, 142 .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 143 }; 144 145 static struct emif_regs ddr3_baltos_emif_reg_data = { 146 .sdram_config = MT41K256M16HA125E_EMIF_SDCFG, 147 .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF, 148 .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1, 149 .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2, 150 .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3, 151 .zq_config = MT41K256M16HA125E_ZQ_CFG, 152 .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY, 153 }; 154 155 #ifdef CONFIG_SPL_OS_BOOT 156 int spl_start_uboot(void) 157 { 158 /* break into full u-boot on 'c' */ 159 return (serial_tstc() && serial_getc() == 'c'); 160 } 161 #endif 162 163 #define OSC (V_OSCK/1000000) 164 const struct dpll_params dpll_ddr = { 165 266, OSC-1, 1, -1, -1, -1, -1}; 166 const struct dpll_params dpll_ddr_evm_sk = { 167 303, OSC-1, 1, -1, -1, -1, -1}; 168 const struct dpll_params dpll_ddr_baltos = { 169 400, OSC-1, 1, -1, -1, -1, -1}; 170 171 void am33xx_spl_board_init(void) 172 { 173 int mpu_vdd; 174 int sil_rev; 175 176 /* Get the frequency */ 177 dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); 178 179 /* 180 * The GP EVM, IDK and EVM SK use a TPS65910 PMIC. For all 181 * MPU frequencies we support we use a CORE voltage of 182 * 1.1375V. For MPU voltage we need to switch based on 183 * the frequency we are running at. 184 */ 185 i2c_set_bus_num(1); 186 187 printf("I2C speed: %d Hz\n", CONFIG_SYS_OMAP24_I2C_SPEED); 188 189 if (i2c_probe(TPS65910_CTRL_I2C_ADDR)) { 190 puts("i2c: cannot access TPS65910\n"); 191 return; 192 } 193 194 /* 195 * Depending on MPU clock and PG we will need a different 196 * VDD to drive at that speed. 197 */ 198 sil_rev = readl(&cdev->deviceid) >> 28; 199 mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev, 200 dpll_mpu_opp100.m); 201 202 /* Tell the TPS65910 to use i2c */ 203 tps65910_set_i2c_control(); 204 205 /* First update MPU voltage. */ 206 if (tps65910_voltage_update(MPU, mpu_vdd)) 207 return; 208 209 /* Second, update the CORE voltage. */ 210 if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_3)) 211 return; 212 213 /* Set CORE Frequencies to OPP100 */ 214 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); 215 216 /* Set MPU Frequency to what we detected now that voltages are set */ 217 do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100); 218 219 writel(0x000010ff, PRM_DEVICE_INST + 4); 220 } 221 222 const struct dpll_params *get_dpll_ddr_params(void) 223 { 224 enable_i2c1_pin_mux(); 225 i2c_set_bus_num(1); 226 227 return &dpll_ddr_baltos; 228 } 229 230 void set_uart_mux_conf(void) 231 { 232 enable_uart0_pin_mux(); 233 } 234 235 void set_mux_conf_regs(void) 236 { 237 enable_board_pin_mux(); 238 } 239 240 const struct ctrl_ioregs ioregs_baltos = { 241 .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 242 .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 243 .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 244 .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 245 .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 246 }; 247 248 void sdram_init(void) 249 { 250 gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); 251 gpio_direction_output(GPIO_DDR_VTT_EN, 1); 252 253 config_ddr(400, &ioregs_baltos, 254 &ddr3_baltos_data, 255 &ddr3_baltos_cmd_ctrl_data, 256 &ddr3_baltos_emif_reg_data, 0); 257 } 258 #endif 259 260 /* 261 * Basic board specific setup. Pinmux has been handled already. 262 */ 263 int board_init(void) 264 { 265 #if defined(CONFIG_HW_WATCHDOG) 266 hw_watchdog_init(); 267 #endif 268 269 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 270 #if defined(CONFIG_NOR) || defined(CONFIG_NAND) 271 gpmc_init(); 272 #endif 273 return 0; 274 } 275 276 int ft_board_setup(void *blob, bd_t *bd) 277 { 278 int node, ret; 279 unsigned char mac_addr[6]; 280 BSP_VS_HWPARAM header; 281 282 /* get production data */ 283 if (read_eeprom(&header)) 284 return 0; 285 286 /* setup MAC1 */ 287 mac_addr[0] = header.MAC1[0]; 288 mac_addr[1] = header.MAC1[1]; 289 mac_addr[2] = header.MAC1[2]; 290 mac_addr[3] = header.MAC1[3]; 291 mac_addr[4] = header.MAC1[4]; 292 mac_addr[5] = header.MAC1[5]; 293 294 295 node = fdt_path_offset(blob, "/ocp/ethernet/slave@4a100200"); 296 if (node < 0) { 297 printf("no /soc/fman/ethernet path offset\n"); 298 return -ENODEV; 299 } 300 301 ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6); 302 if (ret) { 303 printf("error setting local-mac-address property\n"); 304 return -ENODEV; 305 } 306 307 /* setup MAC2 */ 308 mac_addr[0] = header.MAC2[0]; 309 mac_addr[1] = header.MAC2[1]; 310 mac_addr[2] = header.MAC2[2]; 311 mac_addr[3] = header.MAC2[3]; 312 mac_addr[4] = header.MAC2[4]; 313 mac_addr[5] = header.MAC2[5]; 314 315 node = fdt_path_offset(blob, "/ocp/ethernet/slave@4a100300"); 316 if (node < 0) { 317 printf("no /soc/fman/ethernet path offset\n"); 318 return -ENODEV; 319 } 320 321 ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6); 322 if (ret) { 323 printf("error setting local-mac-address property\n"); 324 return -ENODEV; 325 } 326 327 printf("\nFDT was successfully setup\n"); 328 329 return 0; 330 } 331 332 static struct module_pin_mux dip_pin_mux[] = { 333 {OFFSET(gpmc_ad12), (MODE(7) | RXACTIVE )}, /* GPIO1_12 */ 334 {OFFSET(gpmc_ad13), (MODE(7) | RXACTIVE )}, /* GPIO1_13 */ 335 {OFFSET(gpmc_ad14), (MODE(7) | RXACTIVE )}, /* GPIO1_14 */ 336 {OFFSET(gpmc_ad15), (MODE(7) | RXACTIVE )}, /* GPIO1_15 */ 337 {-1}, 338 }; 339 340 #ifdef CONFIG_BOARD_LATE_INIT 341 int board_late_init(void) 342 { 343 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 344 BSP_VS_HWPARAM header; 345 char model[4]; 346 347 /* get production data */ 348 if (read_eeprom(&header)) { 349 sprintf(model, "211"); 350 } else { 351 sprintf(model, "%d", header.SystemId); 352 if (header.SystemId == 215) { 353 configure_module_pin_mux(dip_pin_mux); 354 baltos_set_console(); 355 } 356 } 357 setenv("board_name", model); 358 #endif 359 360 return 0; 361 } 362 #endif 363 364 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 365 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 366 static void cpsw_control(int enabled) 367 { 368 /* VTP can be added here */ 369 370 return; 371 } 372 373 static struct cpsw_slave_data cpsw_slaves[] = { 374 { 375 .slave_reg_ofs = 0x208, 376 .sliver_reg_ofs = 0xd80, 377 .phy_addr = 0, 378 }, 379 { 380 .slave_reg_ofs = 0x308, 381 .sliver_reg_ofs = 0xdc0, 382 .phy_addr = 7, 383 }, 384 }; 385 386 static struct cpsw_platform_data cpsw_data = { 387 .mdio_base = CPSW_MDIO_BASE, 388 .cpsw_base = CPSW_BASE, 389 .mdio_div = 0xff, 390 .channels = 8, 391 .cpdma_reg_ofs = 0x800, 392 .slaves = 2, 393 .slave_data = cpsw_slaves, 394 .active_slave = 1, 395 .ale_reg_ofs = 0xd00, 396 .ale_entries = 1024, 397 .host_port_reg_ofs = 0x108, 398 .hw_stats_reg_ofs = 0x900, 399 .bd_ram_ofs = 0x2000, 400 .mac_control = (1 << 5), 401 .control = cpsw_control, 402 .host_port_num = 0, 403 .version = CPSW_CTRL_VERSION_2, 404 }; 405 #endif 406 407 #if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) \ 408 && defined(CONFIG_SPL_BUILD)) || \ 409 ((defined(CONFIG_DRIVER_TI_CPSW) || \ 410 defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \ 411 !defined(CONFIG_SPL_BUILD)) 412 int board_eth_init(bd_t *bis) 413 { 414 int rv, n = 0; 415 uint8_t mac_addr[6]; 416 uint32_t mac_hi, mac_lo; 417 __maybe_unused struct am335x_baseboard_id header; 418 419 /* 420 * Note here that we're using CPSW1 since that has a 1Gbit PHY while 421 * CSPW0 has a 100Mbit PHY. 422 * 423 * On product, CPSW1 maps to port labeled WAN. 424 */ 425 426 /* try reading mac address from efuse */ 427 mac_lo = readl(&cdev->macid1l); 428 mac_hi = readl(&cdev->macid1h); 429 mac_addr[0] = mac_hi & 0xFF; 430 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 431 mac_addr[2] = (mac_hi & 0xFF0000) >> 16; 432 mac_addr[3] = (mac_hi & 0xFF000000) >> 24; 433 mac_addr[4] = mac_lo & 0xFF; 434 mac_addr[5] = (mac_lo & 0xFF00) >> 8; 435 436 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 437 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 438 if (!getenv("ethaddr")) { 439 printf("<ethaddr> not set. Validating first E-fuse MAC\n"); 440 441 if (is_valid_ethaddr(mac_addr)) 442 eth_setenv_enetaddr("ethaddr", mac_addr); 443 } 444 445 #ifdef CONFIG_DRIVER_TI_CPSW 446 writel((GMII1_SEL_RMII | GMII2_SEL_RGMII | RGMII2_IDMODE), &cdev->miisel); 447 cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RGMII; 448 rv = cpsw_register(&cpsw_data); 449 if (rv < 0) 450 printf("Error %d registering CPSW switch\n", rv); 451 else 452 n += rv; 453 #endif 454 455 /* 456 * 457 * CPSW RGMII Internal Delay Mode is not supported in all PVT 458 * operating points. So we must set the TX clock delay feature 459 * in the AR8051 PHY. Since we only support a single ethernet 460 * device in U-Boot, we only do this for the first instance. 461 */ 462 #define AR8051_PHY_DEBUG_ADDR_REG 0x1d 463 #define AR8051_PHY_DEBUG_DATA_REG 0x1e 464 #define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5 465 #define AR8051_RGMII_TX_CLK_DLY 0x100 466 const char *devname; 467 devname = miiphy_get_current_dev(); 468 469 miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_ADDR_REG, 470 AR8051_DEBUG_RGMII_CLK_DLY_REG); 471 miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_DATA_REG, 472 AR8051_RGMII_TX_CLK_DLY); 473 #endif 474 return n; 475 } 476 #endif 477