1 /* 2 * board.c 3 * 4 * Board functions for TI AM335X based boards 5 * 6 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <errno.h> 13 #include <linux/libfdt.h> 14 #include <spl.h> 15 #include <asm/arch/cpu.h> 16 #include <asm/arch/hardware.h> 17 #include <asm/arch/omap.h> 18 #include <asm/arch/ddr_defs.h> 19 #include <asm/arch/clock.h> 20 #include <asm/arch/gpio.h> 21 #include <asm/arch/mmc_host_def.h> 22 #include <asm/arch/sys_proto.h> 23 #include <asm/arch/mem.h> 24 #include <asm/arch/mux.h> 25 #include <asm/io.h> 26 #include <asm/emif.h> 27 #include <asm/gpio.h> 28 #include <i2c.h> 29 #include <miiphy.h> 30 #include <cpsw.h> 31 #include <power/tps65217.h> 32 #include <power/tps65910.h> 33 #include <environment.h> 34 #include <watchdog.h> 35 #include "board.h" 36 37 DECLARE_GLOBAL_DATA_PTR; 38 39 /* GPIO that controls power to DDR on EVM-SK */ 40 #define GPIO_DDR_VTT_EN 7 41 #define DIP_S1 44 42 #define MPCIE_SW 100 43 44 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 45 46 static int baltos_set_console(void) 47 { 48 int val, i, dips = 0; 49 char buf[7]; 50 51 for (i = 0; i < 4; i++) { 52 sprintf(buf, "dip_s%d", i + 1); 53 54 if (gpio_request(DIP_S1 + i, buf)) { 55 printf("failed to export GPIO %d\n", DIP_S1 + i); 56 return 0; 57 } 58 59 if (gpio_direction_input(DIP_S1 + i)) { 60 printf("failed to set GPIO %d direction\n", DIP_S1 + i); 61 return 0; 62 } 63 64 val = gpio_get_value(DIP_S1 + i); 65 dips |= val << i; 66 } 67 68 printf("DIPs: 0x%1x\n", (~dips) & 0xf); 69 70 if ((dips & 0xf) == 0xe) 71 env_set("console", "ttyUSB0,115200n8"); 72 73 return 0; 74 } 75 76 static int read_eeprom(BSP_VS_HWPARAM *header) 77 { 78 i2c_set_bus_num(1); 79 80 /* Check if baseboard eeprom is available */ 81 if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) { 82 puts("Could not probe the EEPROM; something fundamentally " 83 "wrong on the I2C bus.\n"); 84 return -ENODEV; 85 } 86 87 /* read the eeprom using i2c */ 88 if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header, 89 sizeof(BSP_VS_HWPARAM))) { 90 puts("Could not read the EEPROM; something fundamentally" 91 " wrong on the I2C bus.\n"); 92 return -EIO; 93 } 94 95 if (header->Magic != 0xDEADBEEF) { 96 97 printf("Incorrect magic number (0x%x) in EEPROM\n", 98 header->Magic); 99 100 /* fill default values */ 101 header->SystemId = 211; 102 header->MAC1[0] = 0x00; 103 header->MAC1[1] = 0x00; 104 header->MAC1[2] = 0x00; 105 header->MAC1[3] = 0x00; 106 header->MAC1[4] = 0x00; 107 header->MAC1[5] = 0x01; 108 109 header->MAC2[0] = 0x00; 110 header->MAC2[1] = 0x00; 111 header->MAC2[2] = 0x00; 112 header->MAC2[3] = 0x00; 113 header->MAC2[4] = 0x00; 114 header->MAC2[5] = 0x02; 115 116 header->MAC3[0] = 0x00; 117 header->MAC3[1] = 0x00; 118 header->MAC3[2] = 0x00; 119 header->MAC3[3] = 0x00; 120 header->MAC3[4] = 0x00; 121 header->MAC3[5] = 0x03; 122 } 123 124 return 0; 125 } 126 127 #if defined(CONFIG_SPL_BUILD) || defined(CONFIG_NOR_BOOT) 128 129 static const struct ddr_data ddr3_baltos_data = { 130 .datardsratio0 = MT41K256M16HA125E_RD_DQS, 131 .datawdsratio0 = MT41K256M16HA125E_WR_DQS, 132 .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE, 133 .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA, 134 }; 135 136 static const struct cmd_control ddr3_baltos_cmd_ctrl_data = { 137 .cmd0csratio = MT41K256M16HA125E_RATIO, 138 .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 139 140 .cmd1csratio = MT41K256M16HA125E_RATIO, 141 .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 142 143 .cmd2csratio = MT41K256M16HA125E_RATIO, 144 .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 145 }; 146 147 static struct emif_regs ddr3_baltos_emif_reg_data = { 148 .sdram_config = MT41K256M16HA125E_EMIF_SDCFG, 149 .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF, 150 .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1, 151 .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2, 152 .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3, 153 .zq_config = MT41K256M16HA125E_ZQ_CFG, 154 .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY, 155 }; 156 157 #ifdef CONFIG_SPL_OS_BOOT 158 int spl_start_uboot(void) 159 { 160 /* break into full u-boot on 'c' */ 161 return (serial_tstc() && serial_getc() == 'c'); 162 } 163 #endif 164 165 #define OSC (V_OSCK/1000000) 166 const struct dpll_params dpll_ddr = { 167 266, OSC-1, 1, -1, -1, -1, -1}; 168 const struct dpll_params dpll_ddr_evm_sk = { 169 303, OSC-1, 1, -1, -1, -1, -1}; 170 const struct dpll_params dpll_ddr_baltos = { 171 400, OSC-1, 1, -1, -1, -1, -1}; 172 173 void am33xx_spl_board_init(void) 174 { 175 int mpu_vdd; 176 int sil_rev; 177 178 /* Get the frequency */ 179 dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); 180 181 /* 182 * The GP EVM, IDK and EVM SK use a TPS65910 PMIC. For all 183 * MPU frequencies we support we use a CORE voltage of 184 * 1.1375V. For MPU voltage we need to switch based on 185 * the frequency we are running at. 186 */ 187 i2c_set_bus_num(1); 188 189 printf("I2C speed: %d Hz\n", CONFIG_SYS_OMAP24_I2C_SPEED); 190 191 if (i2c_probe(TPS65910_CTRL_I2C_ADDR)) { 192 puts("i2c: cannot access TPS65910\n"); 193 return; 194 } 195 196 /* 197 * Depending on MPU clock and PG we will need a different 198 * VDD to drive at that speed. 199 */ 200 sil_rev = readl(&cdev->deviceid) >> 28; 201 mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev, 202 dpll_mpu_opp100.m); 203 204 /* Tell the TPS65910 to use i2c */ 205 tps65910_set_i2c_control(); 206 207 /* First update MPU voltage. */ 208 if (tps65910_voltage_update(MPU, mpu_vdd)) 209 return; 210 211 /* Second, update the CORE voltage. */ 212 if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_3)) 213 return; 214 215 /* Set CORE Frequencies to OPP100 */ 216 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); 217 218 /* Set MPU Frequency to what we detected now that voltages are set */ 219 do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100); 220 221 writel(0x000010ff, PRM_DEVICE_INST + 4); 222 } 223 224 const struct dpll_params *get_dpll_ddr_params(void) 225 { 226 enable_i2c1_pin_mux(); 227 i2c_set_bus_num(1); 228 229 return &dpll_ddr_baltos; 230 } 231 232 void set_uart_mux_conf(void) 233 { 234 enable_uart0_pin_mux(); 235 } 236 237 void set_mux_conf_regs(void) 238 { 239 enable_board_pin_mux(); 240 } 241 242 const struct ctrl_ioregs ioregs_baltos = { 243 .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 244 .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 245 .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 246 .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 247 .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 248 }; 249 250 void sdram_init(void) 251 { 252 gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); 253 gpio_direction_output(GPIO_DDR_VTT_EN, 1); 254 255 config_ddr(400, &ioregs_baltos, 256 &ddr3_baltos_data, 257 &ddr3_baltos_cmd_ctrl_data, 258 &ddr3_baltos_emif_reg_data, 0); 259 } 260 #endif 261 262 /* 263 * Basic board specific setup. Pinmux has been handled already. 264 */ 265 int board_init(void) 266 { 267 #if defined(CONFIG_HW_WATCHDOG) 268 hw_watchdog_init(); 269 #endif 270 271 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 272 #if defined(CONFIG_NOR) || defined(CONFIG_NAND) 273 gpmc_init(); 274 #endif 275 return 0; 276 } 277 278 int ft_board_setup(void *blob, bd_t *bd) 279 { 280 int node, ret; 281 unsigned char mac_addr[6]; 282 BSP_VS_HWPARAM header; 283 284 /* get production data */ 285 if (read_eeprom(&header)) 286 return 0; 287 288 /* setup MAC1 */ 289 mac_addr[0] = header.MAC1[0]; 290 mac_addr[1] = header.MAC1[1]; 291 mac_addr[2] = header.MAC1[2]; 292 mac_addr[3] = header.MAC1[3]; 293 mac_addr[4] = header.MAC1[4]; 294 mac_addr[5] = header.MAC1[5]; 295 296 297 node = fdt_path_offset(blob, "/ocp/ethernet/slave@4a100200"); 298 if (node < 0) { 299 printf("no /soc/fman/ethernet path offset\n"); 300 return -ENODEV; 301 } 302 303 ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6); 304 if (ret) { 305 printf("error setting local-mac-address property\n"); 306 return -ENODEV; 307 } 308 309 /* setup MAC2 */ 310 mac_addr[0] = header.MAC2[0]; 311 mac_addr[1] = header.MAC2[1]; 312 mac_addr[2] = header.MAC2[2]; 313 mac_addr[3] = header.MAC2[3]; 314 mac_addr[4] = header.MAC2[4]; 315 mac_addr[5] = header.MAC2[5]; 316 317 node = fdt_path_offset(blob, "/ocp/ethernet/slave@4a100300"); 318 if (node < 0) { 319 printf("no /soc/fman/ethernet path offset\n"); 320 return -ENODEV; 321 } 322 323 ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6); 324 if (ret) { 325 printf("error setting local-mac-address property\n"); 326 return -ENODEV; 327 } 328 329 printf("\nFDT was successfully setup\n"); 330 331 return 0; 332 } 333 334 static struct module_pin_mux pcie_sw_pin_mux[] = { 335 {OFFSET(mii1_rxdv), (MODE(7) | PULLUDEN )}, /* GPIO3_4 */ 336 {-1}, 337 }; 338 339 static struct module_pin_mux dip_pin_mux[] = { 340 {OFFSET(gpmc_ad12), (MODE(7) | RXACTIVE )}, /* GPIO1_12 */ 341 {OFFSET(gpmc_ad13), (MODE(7) | RXACTIVE )}, /* GPIO1_13 */ 342 {OFFSET(gpmc_ad14), (MODE(7) | RXACTIVE )}, /* GPIO1_14 */ 343 {OFFSET(gpmc_ad15), (MODE(7) | RXACTIVE )}, /* GPIO1_15 */ 344 {-1}, 345 }; 346 347 #ifdef CONFIG_BOARD_LATE_INIT 348 int board_late_init(void) 349 { 350 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 351 BSP_VS_HWPARAM header; 352 char model[4]; 353 354 /* get production data */ 355 if (read_eeprom(&header)) { 356 strcpy(model, "211"); 357 } else { 358 sprintf(model, "%d", header.SystemId); 359 if (header.SystemId == 215) { 360 configure_module_pin_mux(dip_pin_mux); 361 baltos_set_console(); 362 } 363 } 364 365 /* turn power for the mPCIe slot */ 366 configure_module_pin_mux(pcie_sw_pin_mux); 367 if (gpio_request(MPCIE_SW, "mpcie_sw")) { 368 printf("failed to export GPIO %d\n", MPCIE_SW); 369 return -ENODEV; 370 } 371 if (gpio_direction_output(MPCIE_SW, 1)) { 372 printf("failed to set GPIO %d direction\n", MPCIE_SW); 373 return -ENODEV; 374 } 375 376 env_set("board_name", model); 377 #endif 378 379 return 0; 380 } 381 #endif 382 383 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 384 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 385 static void cpsw_control(int enabled) 386 { 387 /* VTP can be added here */ 388 389 return; 390 } 391 392 static struct cpsw_slave_data cpsw_slaves[] = { 393 { 394 .slave_reg_ofs = 0x208, 395 .sliver_reg_ofs = 0xd80, 396 .phy_addr = 0, 397 }, 398 { 399 .slave_reg_ofs = 0x308, 400 .sliver_reg_ofs = 0xdc0, 401 .phy_addr = 7, 402 }, 403 }; 404 405 static struct cpsw_platform_data cpsw_data = { 406 .mdio_base = CPSW_MDIO_BASE, 407 .cpsw_base = CPSW_BASE, 408 .mdio_div = 0xff, 409 .channels = 8, 410 .cpdma_reg_ofs = 0x800, 411 .slaves = 2, 412 .slave_data = cpsw_slaves, 413 .active_slave = 1, 414 .ale_reg_ofs = 0xd00, 415 .ale_entries = 1024, 416 .host_port_reg_ofs = 0x108, 417 .hw_stats_reg_ofs = 0x900, 418 .bd_ram_ofs = 0x2000, 419 .mac_control = (1 << 5), 420 .control = cpsw_control, 421 .host_port_num = 0, 422 .version = CPSW_CTRL_VERSION_2, 423 }; 424 #endif 425 426 #if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USB_ETHER)) \ 427 && defined(CONFIG_SPL_BUILD)) || \ 428 ((defined(CONFIG_DRIVER_TI_CPSW) || \ 429 defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \ 430 !defined(CONFIG_SPL_BUILD)) 431 int board_eth_init(bd_t *bis) 432 { 433 int rv, n = 0; 434 uint8_t mac_addr[6]; 435 uint32_t mac_hi, mac_lo; 436 437 /* 438 * Note here that we're using CPSW1 since that has a 1Gbit PHY while 439 * CSPW0 has a 100Mbit PHY. 440 * 441 * On product, CPSW1 maps to port labeled WAN. 442 */ 443 444 /* try reading mac address from efuse */ 445 mac_lo = readl(&cdev->macid1l); 446 mac_hi = readl(&cdev->macid1h); 447 mac_addr[0] = mac_hi & 0xFF; 448 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 449 mac_addr[2] = (mac_hi & 0xFF0000) >> 16; 450 mac_addr[3] = (mac_hi & 0xFF000000) >> 24; 451 mac_addr[4] = mac_lo & 0xFF; 452 mac_addr[5] = (mac_lo & 0xFF00) >> 8; 453 454 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 455 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 456 if (!env_get("ethaddr")) { 457 printf("<ethaddr> not set. Validating first E-fuse MAC\n"); 458 459 if (is_valid_ethaddr(mac_addr)) 460 eth_env_set_enetaddr("ethaddr", mac_addr); 461 } 462 463 #ifdef CONFIG_DRIVER_TI_CPSW 464 writel((GMII1_SEL_RMII | GMII2_SEL_RGMII | RGMII2_IDMODE), &cdev->miisel); 465 cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RGMII; 466 rv = cpsw_register(&cpsw_data); 467 if (rv < 0) 468 printf("Error %d registering CPSW switch\n", rv); 469 else 470 n += rv; 471 #endif 472 473 /* 474 * 475 * CPSW RGMII Internal Delay Mode is not supported in all PVT 476 * operating points. So we must set the TX clock delay feature 477 * in the AR8051 PHY. Since we only support a single ethernet 478 * device in U-Boot, we only do this for the first instance. 479 */ 480 #define AR8051_PHY_DEBUG_ADDR_REG 0x1d 481 #define AR8051_PHY_DEBUG_DATA_REG 0x1e 482 #define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5 483 #define AR8051_RGMII_TX_CLK_DLY 0x100 484 const char *devname; 485 devname = miiphy_get_current_dev(); 486 487 miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_ADDR_REG, 488 AR8051_DEBUG_RGMII_CLK_DLY_REG); 489 miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_DATA_REG, 490 AR8051_RGMII_TX_CLK_DLY); 491 #endif 492 return n; 493 } 494 #endif 495