1 /* 2 * Copyright (C) 2014-2015 Freescale Semiconductor, Inc. 3 * Copyright (C) Jasbir Matharu 4 * Copyright (C) UDOO Team 5 * 6 * Author: Breno Lima <breno.lima@nxp.com> 7 * Author: Francesco Montefoschi <francesco.monte@gmail.com> 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #include <asm/arch/clock.h> 13 #include <asm/arch/crm_regs.h> 14 #include <asm/arch/imx-regs.h> 15 #include <asm/arch/iomux.h> 16 #include <asm/arch/mx6-pins.h> 17 #include <asm/gpio.h> 18 #include <asm/mach-imx/iomux-v3.h> 19 #include <mmc.h> 20 #include <fsl_esdhc.h> 21 #include <asm/arch/crm_regs.h> 22 #include <asm/io.h> 23 #include <asm/mach-imx/mxc_i2c.h> 24 #include <asm/arch/sys_proto.h> 25 #include <spl.h> 26 #include <linux/sizes.h> 27 #include <common.h> 28 #include <i2c.h> 29 #include <miiphy.h> 30 #include <netdev.h> 31 #include <power/pmic.h> 32 #include <power/pfuze3000_pmic.h> 33 #include <malloc.h> 34 35 DECLARE_GLOBAL_DATA_PTR; 36 37 enum { 38 UDOO_NEO_TYPE_BASIC, 39 UDOO_NEO_TYPE_BASIC_KS, 40 UDOO_NEO_TYPE_FULL, 41 UDOO_NEO_TYPE_EXTENDED, 42 }; 43 44 #define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 45 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 46 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 47 48 #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 49 PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ 50 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 51 52 #define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 53 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 54 PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 55 PAD_CTL_ODE) 56 57 #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ 58 PAD_CTL_SPEED_MED | \ 59 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 60 61 #define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ 62 PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) 63 64 #define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 65 PAD_CTL_SPEED_MED | PAD_CTL_SRE_FAST) 66 67 #define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED | \ 68 PAD_CTL_DSE_40ohm) 69 70 #define BOARD_DETECT_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 71 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 72 PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST) 73 #define BOARD_DETECT_PAD_CFG (MUX_PAD_CTRL(BOARD_DETECT_PAD_CTRL) | \ 74 MUX_MODE_SION) 75 76 int dram_init(void) 77 { 78 gd->ram_size = imx_ddr_size(); 79 return 0; 80 } 81 82 #ifdef CONFIG_SYS_I2C_MXC 83 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) 84 /* I2C1 for PMIC */ 85 static struct i2c_pads_info i2c_pad_info1 = { 86 .scl = { 87 .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC, 88 .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC, 89 .gp = IMX_GPIO_NR(1, 0), 90 }, 91 .sda = { 92 .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC, 93 .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC, 94 .gp = IMX_GPIO_NR(1, 1), 95 }, 96 }; 97 #endif 98 99 #ifdef CONFIG_POWER 100 int power_init_board(void) 101 { 102 struct pmic *p; 103 int ret; 104 unsigned int reg, rev_id; 105 106 ret = power_pfuze3000_init(PFUZE3000_I2C_BUS); 107 if (ret) 108 return ret; 109 110 p = pmic_get("PFUZE3000"); 111 ret = pmic_probe(p); 112 if (ret) 113 return ret; 114 115 pmic_reg_read(p, PFUZE3000_DEVICEID, ®); 116 pmic_reg_read(p, PFUZE3000_REVID, &rev_id); 117 printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id); 118 119 /* disable Low Power Mode during standby mode */ 120 pmic_reg_read(p, PFUZE3000_LDOGCTL, ®); 121 reg |= 0x1; 122 ret = pmic_reg_write(p, PFUZE3000_LDOGCTL, reg); 123 if (ret) 124 return ret; 125 126 ret = pmic_reg_write(p, PFUZE3000_SW1AMODE, 0xc); 127 if (ret) 128 return ret; 129 130 ret = pmic_reg_write(p, PFUZE3000_SW1BMODE, 0xc); 131 if (ret) 132 return ret; 133 134 ret = pmic_reg_write(p, PFUZE3000_SW2MODE, 0xc); 135 if (ret) 136 return ret; 137 138 ret = pmic_reg_write(p, PFUZE3000_SW3MODE, 0xc); 139 if (ret) 140 return ret; 141 142 /* set SW1A standby voltage 0.975V */ 143 pmic_reg_read(p, PFUZE3000_SW1ASTBY, ®); 144 reg &= ~0x3f; 145 reg |= PFUZE3000_SW1AB_SETP(9750); 146 ret = pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg); 147 if (ret) 148 return ret; 149 150 /* set SW1B standby voltage 0.975V */ 151 pmic_reg_read(p, PFUZE3000_SW1BSTBY, ®); 152 reg &= ~0x3f; 153 reg |= PFUZE3000_SW1AB_SETP(9750); 154 ret = pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg); 155 if (ret) 156 return ret; 157 158 /* set SW1A/VDD_ARM_IN step ramp up time from 16us to 4us/25mV */ 159 pmic_reg_read(p, PFUZE3000_SW1ACONF, ®); 160 reg &= ~0xc0; 161 reg |= 0x40; 162 ret = pmic_reg_write(p, PFUZE3000_SW1ACONF, reg); 163 if (ret) 164 return ret; 165 166 /* set SW1B/VDD_SOC_IN step ramp up time from 16us to 4us/25mV */ 167 pmic_reg_read(p, PFUZE3000_SW1BCONF, ®); 168 reg &= ~0xc0; 169 reg |= 0x40; 170 ret = pmic_reg_write(p, PFUZE3000_SW1BCONF, reg); 171 if (ret) 172 return ret; 173 174 /* set VDD_ARM_IN to 1.350V */ 175 pmic_reg_read(p, PFUZE3000_SW1AVOLT, ®); 176 reg &= ~0x3f; 177 reg |= PFUZE3000_SW1AB_SETP(13500); 178 ret = pmic_reg_write(p, PFUZE3000_SW1AVOLT, reg); 179 if (ret) 180 return ret; 181 182 /* set VDD_SOC_IN to 1.350V */ 183 pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®); 184 reg &= ~0x3f; 185 reg |= PFUZE3000_SW1AB_SETP(13500); 186 ret = pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg); 187 if (ret) 188 return ret; 189 190 /* set DDR_1_5V to 1.350V */ 191 pmic_reg_read(p, PFUZE3000_SW3VOLT, ®); 192 reg &= ~0x0f; 193 reg |= PFUZE3000_SW3_SETP(13500); 194 ret = pmic_reg_write(p, PFUZE3000_SW3VOLT, reg); 195 if (ret) 196 return ret; 197 198 /* set VGEN2_1V5 to 1.5V */ 199 pmic_reg_read(p, PFUZE3000_VLDO2CTL, ®); 200 reg &= ~0x0f; 201 reg |= PFUZE3000_VLDO_SETP(15000); 202 /* enable */ 203 reg |= 0x10; 204 ret = pmic_reg_write(p, PFUZE3000_VLDO2CTL, reg); 205 if (ret) 206 return ret; 207 208 return 0; 209 } 210 #endif 211 212 static iomux_v3_cfg_t const uart1_pads[] = { 213 MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), 214 MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), 215 }; 216 217 static iomux_v3_cfg_t const usdhc2_pads[] = { 218 MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 219 MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 220 MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 221 MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 222 MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 223 MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 224 /* CD pin */ 225 MX6_PAD_SD1_DATA0__GPIO6_IO_2 | MUX_PAD_CTRL(NO_PAD_CTRL), 226 /* Power */ 227 MX6_PAD_SD1_CMD__GPIO6_IO_1 | MUX_PAD_CTRL(NO_PAD_CTRL), 228 }; 229 230 static iomux_v3_cfg_t const fec1_pads[] = { 231 MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 232 MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 233 MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 234 MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 235 MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 236 MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), 237 MX6_PAD_RGMII1_RXC__ENET1_RX_ER | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 238 MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 239 MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 240 MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 241 MX6_PAD_ENET2_TX_CLK__GPIO2_IO_9 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 242 MX6_PAD_ENET1_CRS__GPIO2_IO_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 243 }; 244 245 static iomux_v3_cfg_t const phy_control_pads[] = { 246 /* 25MHz Ethernet PHY Clock */ 247 MX6_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M | 248 MUX_PAD_CTRL(ENET_CLK_PAD_CTRL), 249 }; 250 251 static iomux_v3_cfg_t const board_recognition_pads[] = { 252 /*Connected to R184*/ 253 MX6_PAD_NAND_READY_B__GPIO4_IO_13 | BOARD_DETECT_PAD_CFG, 254 /*Connected to R185*/ 255 MX6_PAD_NAND_ALE__GPIO4_IO_0 | BOARD_DETECT_PAD_CFG, 256 }; 257 258 static iomux_v3_cfg_t const wdog_b_pad = { 259 MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL), 260 }; 261 262 static iomux_v3_cfg_t const peri_3v3_pads[] = { 263 MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL), 264 }; 265 266 static void setup_iomux_uart(void) 267 { 268 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); 269 } 270 271 static int setup_fec(int fec_id) 272 { 273 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; 274 int reg; 275 276 imx_iomux_v3_setup_multiple_pads(phy_control_pads, 277 ARRAY_SIZE(phy_control_pads)); 278 279 /* Reset PHY */ 280 gpio_direction_output(IMX_GPIO_NR(2, 1) , 0); 281 udelay(10000); 282 gpio_set_value(IMX_GPIO_NR(2, 1), 1); 283 udelay(100); 284 285 reg = readl(&anatop->pll_enet); 286 reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE; 287 writel(reg, &anatop->pll_enet); 288 289 return enable_fec_anatop_clock(fec_id, ENET_25MHZ); 290 } 291 292 int board_eth_init(bd_t *bis) 293 { 294 uint32_t base = IMX_FEC_BASE; 295 struct mii_dev *bus = NULL; 296 struct phy_device *phydev = NULL; 297 int ret; 298 299 imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads)); 300 301 setup_fec(CONFIG_FEC_ENET_DEV); 302 303 bus = fec_get_miibus(base, CONFIG_FEC_ENET_DEV); 304 if (!bus) 305 return -EINVAL; 306 307 phydev = phy_find_by_mask(bus, (0x1 << CONFIG_FEC_MXC_PHYADDR), 308 PHY_INTERFACE_MODE_RMII); 309 if (!phydev) { 310 free(bus); 311 return -EINVAL; 312 } 313 314 ret = fec_probe(bis, CONFIG_FEC_ENET_DEV, base, bus, phydev); 315 if (ret) { 316 free(bus); 317 free(phydev); 318 return ret; 319 } 320 return 0; 321 } 322 323 int board_phy_config(struct phy_device *phydev) 324 { 325 if (phydev->drv->config) 326 phydev->drv->config(phydev); 327 328 return 0; 329 } 330 331 int board_init(void) 332 { 333 /* Address of boot parameters */ 334 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 335 336 /* 337 * Because kernel set WDOG_B mux before pad with the commone pinctrl 338 * framwork now and wdog reset will be triggered once set WDOG_B mux 339 * with default pad setting, we set pad setting here to workaround this. 340 * Since imx_iomux_v3_setup_pad also set mux before pad setting, we set 341 * as GPIO mux firstly here to workaround it. 342 */ 343 imx_iomux_v3_setup_pad(wdog_b_pad); 344 345 /* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */ 346 imx_iomux_v3_setup_multiple_pads(peri_3v3_pads, 347 ARRAY_SIZE(peri_3v3_pads)); 348 349 /* Active high for ncp692 */ 350 gpio_direction_output(IMX_GPIO_NR(4, 16) , 1); 351 352 #ifdef CONFIG_SYS_I2C_MXC 353 setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); 354 #endif 355 356 return 0; 357 } 358 359 static int get_board_value(void) 360 { 361 int r184, r185; 362 363 imx_iomux_v3_setup_multiple_pads(board_recognition_pads, 364 ARRAY_SIZE(board_recognition_pads)); 365 366 gpio_direction_input(IMX_GPIO_NR(4, 13)); 367 gpio_direction_input(IMX_GPIO_NR(4, 0)); 368 369 r184 = gpio_get_value(IMX_GPIO_NR(4, 13)); 370 r185 = gpio_get_value(IMX_GPIO_NR(4, 0)); 371 372 /* 373 * Machine selection - 374 * Machine r184, r185 375 * --------------------------------- 376 * Basic 0 0 377 * Basic Ks 0 1 378 * Full 1 0 379 * Extended 1 1 380 */ 381 382 return (r184 << 1) + r185; 383 } 384 385 int board_early_init_f(void) 386 { 387 setup_iomux_uart(); 388 389 return 0; 390 } 391 392 static struct fsl_esdhc_cfg usdhc_cfg[1] = { 393 {USDHC2_BASE_ADDR, 0, 4}, 394 }; 395 396 #define USDHC2_PWR_GPIO IMX_GPIO_NR(6, 1) 397 #define USDHC2_CD_GPIO IMX_GPIO_NR(6, 2) 398 399 int board_mmc_getcd(struct mmc *mmc) 400 { 401 return !gpio_get_value(USDHC2_CD_GPIO); 402 } 403 404 int board_mmc_init(bd_t *bis) 405 { 406 imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); 407 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 408 usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR; 409 gpio_direction_input(USDHC2_CD_GPIO); 410 gpio_direction_output(USDHC2_PWR_GPIO, 1); 411 412 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; 413 return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); 414 } 415 416 static char *board_string(void) 417 { 418 switch (get_board_value()) { 419 case UDOO_NEO_TYPE_BASIC: 420 return "BASIC"; 421 case UDOO_NEO_TYPE_BASIC_KS: 422 return "BASICKS"; 423 case UDOO_NEO_TYPE_FULL: 424 return "FULL"; 425 case UDOO_NEO_TYPE_EXTENDED: 426 return "EXTENDED"; 427 } 428 return "UNDEFINED"; 429 } 430 431 int checkboard(void) 432 { 433 printf("Board: UDOO Neo %s\n", board_string()); 434 return 0; 435 } 436 437 int board_late_init(void) 438 { 439 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 440 env_set("board_name", board_string()); 441 #endif 442 443 return 0; 444 } 445 446 #ifdef CONFIG_SPL_BUILD 447 448 #include <linux/libfdt.h> 449 #include <asm/arch/mx6-ddr.h> 450 451 static const struct mx6sx_iomux_ddr_regs mx6_ddr_ioregs = { 452 .dram_dqm0 = 0x00000028, 453 .dram_dqm1 = 0x00000028, 454 .dram_dqm2 = 0x00000028, 455 .dram_dqm3 = 0x00000028, 456 .dram_ras = 0x00000020, 457 .dram_cas = 0x00000020, 458 .dram_odt0 = 0x00000020, 459 .dram_odt1 = 0x00000020, 460 .dram_sdba2 = 0x00000000, 461 .dram_sdcke0 = 0x00003000, 462 .dram_sdcke1 = 0x00003000, 463 .dram_sdclk_0 = 0x00000030, 464 .dram_sdqs0 = 0x00000028, 465 .dram_sdqs1 = 0x00000028, 466 .dram_sdqs2 = 0x00000028, 467 .dram_sdqs3 = 0x00000028, 468 .dram_reset = 0x00000020, 469 }; 470 471 static const struct mx6sx_iomux_grp_regs mx6_grp_ioregs = { 472 .grp_addds = 0x00000020, 473 .grp_ddrmode_ctl = 0x00020000, 474 .grp_ddrpke = 0x00000000, 475 .grp_ddrmode = 0x00020000, 476 .grp_b0ds = 0x00000028, 477 .grp_b1ds = 0x00000028, 478 .grp_ctlds = 0x00000020, 479 .grp_ddr_type = 0x000c0000, 480 .grp_b2ds = 0x00000028, 481 .grp_b3ds = 0x00000028, 482 }; 483 484 static const struct mx6_mmdc_calibration neo_mmcd_calib = { 485 .p0_mpwldectrl0 = 0x000E000B, 486 .p0_mpwldectrl1 = 0x000E0010, 487 .p0_mpdgctrl0 = 0x41600158, 488 .p0_mpdgctrl1 = 0x01500140, 489 .p0_mprddlctl = 0x3A383E3E, 490 .p0_mpwrdlctl = 0x3A383C38, 491 }; 492 493 static const struct mx6_mmdc_calibration neo_basic_mmcd_calib = { 494 .p0_mpwldectrl0 = 0x001E0022, 495 .p0_mpwldectrl1 = 0x001C0019, 496 .p0_mpdgctrl0 = 0x41540150, 497 .p0_mpdgctrl1 = 0x01440138, 498 .p0_mprddlctl = 0x403E4644, 499 .p0_mpwrdlctl = 0x3C3A4038, 500 }; 501 502 /* MT41K256M16 */ 503 static struct mx6_ddr3_cfg neo_mem_ddr = { 504 .mem_speed = 1600, 505 .density = 4, 506 .width = 16, 507 .banks = 8, 508 .rowaddr = 15, 509 .coladdr = 10, 510 .pagesz = 2, 511 .trcd = 1375, 512 .trcmin = 4875, 513 .trasmin = 3500, 514 }; 515 516 /* MT41K128M16 */ 517 static struct mx6_ddr3_cfg neo_basic_mem_ddr = { 518 .mem_speed = 1600, 519 .density = 2, 520 .width = 16, 521 .banks = 8, 522 .rowaddr = 14, 523 .coladdr = 10, 524 .pagesz = 2, 525 .trcd = 1375, 526 .trcmin = 4875, 527 .trasmin = 3500, 528 }; 529 530 static void ccgr_init(void) 531 { 532 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 533 534 writel(0xFFFFFFFF, &ccm->CCGR0); 535 writel(0xFFFFFFFF, &ccm->CCGR1); 536 writel(0xFFFFFFFF, &ccm->CCGR2); 537 writel(0xFFFFFFFF, &ccm->CCGR3); 538 writel(0xFFFFFFFF, &ccm->CCGR4); 539 writel(0xFFFFFFFF, &ccm->CCGR5); 540 writel(0xFFFFFFFF, &ccm->CCGR6); 541 writel(0xFFFFFFFF, &ccm->CCGR7); 542 } 543 544 static void spl_dram_init(void) 545 { 546 int board = get_board_value(); 547 548 struct mx6_ddr_sysinfo sysinfo = { 549 .dsize = 1, /* width of data bus: 1 = 32 bits */ 550 .cs_density = 24, 551 .ncs = 1, 552 .cs1_mirror = 0, 553 .rtt_wr = 2, 554 .rtt_nom = 2, /* RTT_Nom = RZQ/2 */ 555 .walat = 1, /* Write additional latency */ 556 .ralat = 5, /* Read additional latency */ 557 .mif3_mode = 3, /* Command prediction working mode */ 558 .bi_on = 1, /* Bank interleaving enabled */ 559 .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ 560 .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ 561 }; 562 563 mx6sx_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs); 564 if (board == UDOO_NEO_TYPE_BASIC || board == UDOO_NEO_TYPE_BASIC_KS) 565 mx6_dram_cfg(&sysinfo, &neo_basic_mmcd_calib, 566 &neo_basic_mem_ddr); 567 else 568 mx6_dram_cfg(&sysinfo, &neo_mmcd_calib, &neo_mem_ddr); 569 } 570 571 void board_init_f(ulong dummy) 572 { 573 ccgr_init(); 574 575 /* setup AIPS and disable watchdog */ 576 arch_cpu_init(); 577 578 board_early_init_f(); 579 580 /* setup GP timer */ 581 timer_init(); 582 583 /* UART clocks enabled and gd valid - init serial console */ 584 preloader_console_init(); 585 586 /* DDR initialization */ 587 spl_dram_init(); 588 589 /* Clear the BSS. */ 590 memset(__bss_start, 0, __bss_end - __bss_start); 591 592 /* load/boot image from boot device */ 593 board_init_r(NULL, 0); 594 } 595 596 #endif 597