1 /* 2 * Copyright (C) 2012 Freescale Semiconductor, Inc. 3 * Author: Fabio Estevam <fabio.estevam@freescale.com> 4 * 5 * Copyright (C) 2013, 2014 TQ Systems (ported SabreSD to TQMa6x) 6 * Author: Markus Niebel <markus.niebel@tq-group.com> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <asm/io.h> 12 #include <asm/arch/clock.h> 13 #include <asm/arch/mx6-pins.h> 14 #include <asm/arch/imx-regs.h> 15 #include <asm/arch/iomux.h> 16 #include <asm/arch/sys_proto.h> 17 #include <linux/errno.h> 18 #include <asm/gpio.h> 19 #include <asm/mach-imx/mxc_i2c.h> 20 21 #include <common.h> 22 #include <fsl_esdhc.h> 23 #include <libfdt.h> 24 #include <malloc.h> 25 #include <i2c.h> 26 #include <micrel.h> 27 #include <miiphy.h> 28 #include <mmc.h> 29 #include <netdev.h> 30 31 #include "tqma6_bb.h" 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 36 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 37 38 #define USDHC_CLK_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ 39 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 40 41 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ 42 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 43 44 #define GPIO_OUT_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \ 45 PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 46 47 #define GPIO_IN_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \ 48 PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 49 50 #define SPI_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 51 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 52 53 #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 54 PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \ 55 PAD_CTL_ODE | PAD_CTL_SRE_FAST) 56 57 #if defined(CONFIG_TQMA6Q) 58 59 #define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII 0x02e0790 60 #define IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM 0x02e07ac 61 62 #elif defined(CONFIG_TQMA6S) || defined(CONFIG_TQMA6DL) 63 64 #define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII 0x02e0768 65 #define IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM 0x02e0788 66 67 #else 68 69 #error "need to select module" 70 71 #endif 72 73 #define ENET_RX_PAD_CTRL (PAD_CTL_DSE_34ohm) 74 #define ENET_TX_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_34ohm) 75 #define ENET_CLK_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_HIGH | \ 76 PAD_CTL_DSE_34ohm) 77 #define ENET_MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 78 PAD_CTL_DSE_60ohm) 79 80 /* disable on die termination for RGMII */ 81 #define IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM_DISABLE 0x00000000 82 /* optimised drive strength for 1.0 .. 1.3 V signal on RGMII */ 83 #define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII_1P2V 0x00080000 84 /* optimised drive strength for 1.3 .. 2.5 V signal on RGMII */ 85 #define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII_1P5V 0x000C0000 86 87 #define ENET_PHY_RESET_GPIO IMX_GPIO_NR(1, 25) 88 89 static iomux_v3_cfg_t const mba6_enet_pads[] = { 90 NEW_PAD_CTRL(MX6_PAD_ENET_MDIO__ENET_MDIO, ENET_MDIO_PAD_CTRL), 91 NEW_PAD_CTRL(MX6_PAD_ENET_MDC__ENET_MDC, ENET_MDIO_PAD_CTRL), 92 93 NEW_PAD_CTRL(MX6_PAD_RGMII_TXC__RGMII_TXC, ENET_TX_PAD_CTRL), 94 NEW_PAD_CTRL(MX6_PAD_RGMII_TD0__RGMII_TD0, ENET_TX_PAD_CTRL), 95 NEW_PAD_CTRL(MX6_PAD_RGMII_TD1__RGMII_TD1, ENET_TX_PAD_CTRL), 96 NEW_PAD_CTRL(MX6_PAD_RGMII_TD2__RGMII_TD2, ENET_TX_PAD_CTRL), 97 NEW_PAD_CTRL(MX6_PAD_RGMII_TD3__RGMII_TD3, ENET_TX_PAD_CTRL), 98 NEW_PAD_CTRL(MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL, 99 ENET_TX_PAD_CTRL), 100 NEW_PAD_CTRL(MX6_PAD_ENET_REF_CLK__ENET_TX_CLK, ENET_CLK_PAD_CTRL), 101 /* 102 * these pins are also used for config strapping by phy 103 */ 104 NEW_PAD_CTRL(MX6_PAD_RGMII_RD0__RGMII_RD0, ENET_RX_PAD_CTRL), 105 NEW_PAD_CTRL(MX6_PAD_RGMII_RD1__RGMII_RD1, ENET_RX_PAD_CTRL), 106 NEW_PAD_CTRL(MX6_PAD_RGMII_RD2__RGMII_RD2, ENET_RX_PAD_CTRL), 107 NEW_PAD_CTRL(MX6_PAD_RGMII_RD3__RGMII_RD3, ENET_RX_PAD_CTRL), 108 NEW_PAD_CTRL(MX6_PAD_RGMII_RXC__RGMII_RXC, ENET_RX_PAD_CTRL), 109 NEW_PAD_CTRL(MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL, 110 ENET_RX_PAD_CTRL), 111 /* KSZ9031 PHY Reset */ 112 NEW_PAD_CTRL(MX6_PAD_ENET_CRS_DV__GPIO1_IO25, GPIO_OUT_PAD_CTRL), 113 }; 114 115 static void mba6_setup_iomuxc_enet(void) 116 { 117 struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 118 119 /* clear gpr1[ENET_CLK_SEL] for externel clock */ 120 clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK); 121 122 __raw_writel(IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM_DISABLE, 123 (void *)IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM); 124 __raw_writel(IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII_1P5V, 125 (void *)IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII); 126 127 imx_iomux_v3_setup_multiple_pads(mba6_enet_pads, 128 ARRAY_SIZE(mba6_enet_pads)); 129 130 /* Reset PHY */ 131 gpio_direction_output(ENET_PHY_RESET_GPIO , 0); 132 /* Need delay 10ms after power on according to KSZ9031 spec */ 133 mdelay(10); 134 gpio_set_value(ENET_PHY_RESET_GPIO, 1); 135 /* 136 * KSZ9031 manual: 100 usec wait time after reset before communication 137 * over MDIO 138 * BUGBUG: hardware has an RC const that needs > 10 msec from 0->1 on 139 * reset before the phy sees a high level 140 */ 141 mdelay(15); 142 } 143 144 static iomux_v3_cfg_t const mba6_uart2_pads[] = { 145 NEW_PAD_CTRL(MX6_PAD_SD4_DAT4__UART2_RX_DATA, UART_PAD_CTRL), 146 NEW_PAD_CTRL(MX6_PAD_SD4_DAT7__UART2_TX_DATA, UART_PAD_CTRL), 147 }; 148 149 static void mba6_setup_iomuxc_uart(void) 150 { 151 imx_iomux_v3_setup_multiple_pads(mba6_uart2_pads, 152 ARRAY_SIZE(mba6_uart2_pads)); 153 } 154 155 #define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4) 156 #define USDHC2_WP_GPIO IMX_GPIO_NR(1, 2) 157 158 int tqma6_bb_board_mmc_getcd(struct mmc *mmc) 159 { 160 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 161 int ret = 0; 162 163 if (cfg->esdhc_base == USDHC2_BASE_ADDR) 164 ret = !gpio_get_value(USDHC2_CD_GPIO); 165 166 return ret; 167 } 168 169 int tqma6_bb_board_mmc_getwp(struct mmc *mmc) 170 { 171 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 172 int ret = 0; 173 174 if (cfg->esdhc_base == USDHC2_BASE_ADDR) 175 ret = gpio_get_value(USDHC2_WP_GPIO); 176 177 return ret; 178 } 179 180 static struct fsl_esdhc_cfg mba6_usdhc_cfg = { 181 .esdhc_base = USDHC2_BASE_ADDR, 182 .max_bus_width = 4, 183 }; 184 185 static iomux_v3_cfg_t const mba6_usdhc2_pads[] = { 186 NEW_PAD_CTRL(MX6_PAD_SD2_CLK__SD2_CLK, USDHC_CLK_PAD_CTRL), 187 NEW_PAD_CTRL(MX6_PAD_SD2_CMD__SD2_CMD, USDHC_PAD_CTRL), 188 NEW_PAD_CTRL(MX6_PAD_SD2_DAT0__SD2_DATA0, USDHC_PAD_CTRL), 189 NEW_PAD_CTRL(MX6_PAD_SD2_DAT1__SD2_DATA1, USDHC_PAD_CTRL), 190 NEW_PAD_CTRL(MX6_PAD_SD2_DAT2__SD2_DATA2, USDHC_PAD_CTRL), 191 NEW_PAD_CTRL(MX6_PAD_SD2_DAT3__SD2_DATA3, USDHC_PAD_CTRL), 192 /* CD */ 193 NEW_PAD_CTRL(MX6_PAD_GPIO_4__GPIO1_IO04, GPIO_IN_PAD_CTRL), 194 /* WP */ 195 NEW_PAD_CTRL(MX6_PAD_GPIO_2__GPIO1_IO02, GPIO_IN_PAD_CTRL), 196 }; 197 198 int tqma6_bb_board_mmc_init(bd_t *bis) 199 { 200 imx_iomux_v3_setup_multiple_pads(mba6_usdhc2_pads, 201 ARRAY_SIZE(mba6_usdhc2_pads)); 202 gpio_direction_input(USDHC2_CD_GPIO); 203 gpio_direction_input(USDHC2_WP_GPIO); 204 205 mba6_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 206 if (fsl_esdhc_initialize(bis, &mba6_usdhc_cfg)) 207 puts("Warning: failed to initialize SD\n"); 208 209 return 0; 210 } 211 212 static struct i2c_pads_info mba6_i2c1_pads = { 213 /* I2C1: MBa6x */ 214 .scl = { 215 .i2c_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT9__I2C1_SCL, 216 I2C_PAD_CTRL), 217 .gpio_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT9__GPIO5_IO27, 218 I2C_PAD_CTRL), 219 .gp = IMX_GPIO_NR(5, 27) 220 }, 221 .sda = { 222 .i2c_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT8__I2C1_SDA, 223 I2C_PAD_CTRL), 224 .gpio_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT8__GPIO5_IO26, 225 I2C_PAD_CTRL), 226 .gp = IMX_GPIO_NR(5, 26) 227 } 228 }; 229 230 static void mba6_setup_i2c(void) 231 { 232 int ret; 233 /* 234 * use logical index for bus, e.g. I2C1 -> 0 235 * warn on error 236 */ 237 ret = setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mba6_i2c1_pads); 238 if (ret) 239 printf("setup I2C1 failed: %d\n", ret); 240 } 241 242 int board_phy_config(struct phy_device *phydev) 243 { 244 /* 245 * optimized pad skew values depends on CPU variant on the TQMa6x module: 246 * CONFIG_TQMA6Q: i.MX6Q/D 247 * CONFIG_TQMA6S: i.MX6S 248 * CONFIG_TQMA6DL: i.MX6DL 249 */ 250 #if defined(CONFIG_TQMA6Q) 251 #define MBA6X_KSZ9031_CTRL_SKEW 0x0032 252 #define MBA6X_KSZ9031_CLK_SKEW 0x03ff 253 #define MBA6X_KSZ9031_RX_SKEW 0x3333 254 #define MBA6X_KSZ9031_TX_SKEW 0x2036 255 #elif defined(CONFIG_TQMA6S) || defined(CONFIG_TQMA6DL) 256 #define MBA6X_KSZ9031_CTRL_SKEW 0x0030 257 #define MBA6X_KSZ9031_CLK_SKEW 0x03ff 258 #define MBA6X_KSZ9031_RX_SKEW 0x3333 259 #define MBA6X_KSZ9031_TX_SKEW 0x2052 260 #else 261 #error 262 #endif 263 /* min rx/tx ctrl delay */ 264 ksz9031_phy_extended_write(phydev, 2, 265 MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, 266 MII_KSZ9031_MOD_DATA_NO_POST_INC, 267 MBA6X_KSZ9031_CTRL_SKEW); 268 /* min rx delay */ 269 ksz9031_phy_extended_write(phydev, 2, 270 MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 271 MII_KSZ9031_MOD_DATA_NO_POST_INC, 272 MBA6X_KSZ9031_RX_SKEW); 273 /* max tx delay */ 274 ksz9031_phy_extended_write(phydev, 2, 275 MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 276 MII_KSZ9031_MOD_DATA_NO_POST_INC, 277 MBA6X_KSZ9031_TX_SKEW); 278 /* rx/tx clk skew */ 279 ksz9031_phy_extended_write(phydev, 2, 280 MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, 281 MII_KSZ9031_MOD_DATA_NO_POST_INC, 282 MBA6X_KSZ9031_CLK_SKEW); 283 284 phydev->drv->config(phydev); 285 286 return 0; 287 } 288 289 int board_eth_init(bd_t *bis) 290 { 291 uint32_t base = IMX_FEC_BASE; 292 struct mii_dev *bus = NULL; 293 struct phy_device *phydev = NULL; 294 int ret; 295 296 bus = fec_get_miibus(base, -1); 297 if (!bus) 298 return -EINVAL; 299 /* scan phy */ 300 phydev = phy_find_by_mask(bus, (0xf << CONFIG_FEC_MXC_PHYADDR), 301 PHY_INTERFACE_MODE_RGMII); 302 303 if (!phydev) { 304 ret = -EINVAL; 305 goto free_bus; 306 } 307 ret = fec_probe(bis, -1, base, bus, phydev); 308 if (ret) 309 goto free_phydev; 310 311 return 0; 312 313 free_phydev: 314 free(phydev); 315 free_bus: 316 free(bus); 317 return ret; 318 } 319 320 int tqma6_bb_board_early_init_f(void) 321 { 322 mba6_setup_iomuxc_uart(); 323 324 return 0; 325 } 326 327 int tqma6_bb_board_init(void) 328 { 329 mba6_setup_i2c(); 330 /* do it here - to have reset completed */ 331 mba6_setup_iomuxc_enet(); 332 333 return 0; 334 } 335 336 int tqma6_bb_board_late_init(void) 337 { 338 return 0; 339 } 340 341 const char *tqma6_bb_get_boardname(void) 342 { 343 return "MBa6x"; 344 } 345 346 /* 347 * Device Tree Support 348 */ 349 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) 350 void tqma6_bb_ft_board_setup(void *blob, bd_t *bd) 351 { 352 /* TBD */ 353 } 354 #endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */ 355