1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2010-2013 Freescale Semiconductor, Inc. 4 * Copyright (C) 2013, Boundary Devices <info@boundarydevices.com> 5 * Copyright (C) 2014-2016, Toradex AG 6 * copied from nitrogen6x 7 */ 8 9 #include <common.h> 10 #include <dm.h> 11 #include <environment.h> 12 #include <asm/arch/clock.h> 13 #include <asm/arch/crm_regs.h> 14 #include <asm/arch/mxc_hdmi.h> 15 #include <asm/arch/imx-regs.h> 16 #include <asm/arch/iomux.h> 17 #include <asm/arch/sys_proto.h> 18 #include <asm/arch/mx6-pins.h> 19 #include <asm/arch/mx6-ddr.h> 20 #include <asm/bootm.h> 21 #include <asm/gpio.h> 22 #include <asm/io.h> 23 #include <asm/mach-imx/iomux-v3.h> 24 #include <asm/mach-imx/mxc_i2c.h> 25 #include <asm/mach-imx/sata.h> 26 #include <asm/mach-imx/boot_mode.h> 27 #include <asm/mach-imx/video.h> 28 #include <dm/platform_data/serial_mxc.h> 29 #include <dm/platdata.h> 30 #include <fsl_esdhc.h> 31 #include <i2c.h> 32 #include <input.h> 33 #include <imx_thermal.h> 34 #include <linux/errno.h> 35 #include <malloc.h> 36 #include <mmc.h> 37 #include <micrel.h> 38 #include <miiphy.h> 39 #include <netdev.h> 40 41 #include "../common/tdx-cfg-block.h" 42 #ifdef CONFIG_TDX_CMD_IMX_MFGR 43 #include "pf0100.h" 44 #endif 45 46 DECLARE_GLOBAL_DATA_PTR; 47 48 #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 49 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 50 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 51 52 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ 53 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ 54 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 55 56 #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 57 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 58 59 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ 60 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 61 62 #define BUTTON_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 63 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 64 65 #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 66 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 67 PAD_CTL_ODE | PAD_CTL_SRE_FAST) 68 69 #define WEAK_PULLUP (PAD_CTL_PUS_100K_UP | \ 70 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 71 PAD_CTL_SRE_SLOW) 72 73 #define NO_PULLUP ( \ 74 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 75 PAD_CTL_SRE_SLOW) 76 77 #define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \ 78 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 79 PAD_CTL_HYS | PAD_CTL_SRE_SLOW) 80 81 #define TRISTATE (PAD_CTL_HYS | PAD_CTL_SPEED_MED) 82 83 #define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm) 84 85 #define OUTPUT_RGB (PAD_CTL_SPEED_MED|PAD_CTL_DSE_60ohm|PAD_CTL_SRE_FAST) 86 87 int dram_init(void) 88 { 89 /* use the DDR controllers configured size */ 90 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 91 (ulong)imx_ddr_size()); 92 93 return 0; 94 } 95 96 /* Apalis UART1 */ 97 iomux_v3_cfg_t const uart1_pads_dce[] = { 98 MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 99 MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 100 }; 101 iomux_v3_cfg_t const uart1_pads_dte[] = { 102 MX6_PAD_CSI0_DAT10__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 103 MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 104 }; 105 106 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) 107 /* Apalis I2C1 */ 108 struct i2c_pads_info i2c_pad_info1 = { 109 .scl = { 110 .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC, 111 .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC, 112 .gp = IMX_GPIO_NR(5, 27) 113 }, 114 .sda = { 115 .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC, 116 .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC, 117 .gp = IMX_GPIO_NR(5, 26) 118 } 119 }; 120 121 /* Apalis local, PMIC, SGTL5000, STMPE811 */ 122 struct i2c_pads_info i2c_pad_info_loc = { 123 .scl = { 124 .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC, 125 .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC, 126 .gp = IMX_GPIO_NR(4, 12) 127 }, 128 .sda = { 129 .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC, 130 .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC, 131 .gp = IMX_GPIO_NR(4, 13) 132 } 133 }; 134 135 /* Apalis I2C3 / CAM */ 136 struct i2c_pads_info i2c_pad_info3 = { 137 .scl = { 138 .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC, 139 .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC, 140 .gp = IMX_GPIO_NR(3, 17) 141 }, 142 .sda = { 143 .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC, 144 .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC, 145 .gp = IMX_GPIO_NR(3, 18) 146 } 147 }; 148 149 /* Apalis I2C2 / DDC */ 150 struct i2c_pads_info i2c_pad_info_ddc = { 151 .scl = { 152 .i2c_mode = MX6_PAD_EIM_EB2__HDMI_TX_DDC_SCL | PC, 153 .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC, 154 .gp = IMX_GPIO_NR(2, 30) 155 }, 156 .sda = { 157 .i2c_mode = MX6_PAD_EIM_D16__HDMI_TX_DDC_SDA | PC, 158 .gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC, 159 .gp = IMX_GPIO_NR(3, 16) 160 } 161 }; 162 163 /* Apalis MMC1 */ 164 iomux_v3_cfg_t const usdhc1_pads[] = { 165 MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 166 MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 167 MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 168 MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 169 MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 170 MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 171 MX6_PAD_NANDF_D0__SD1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 172 MX6_PAD_NANDF_D1__SD1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 173 MX6_PAD_NANDF_D2__SD1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 174 MX6_PAD_NANDF_D3__SD1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 175 MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ 176 # define GPIO_MMC_CD IMX_GPIO_NR(4, 20) 177 }; 178 179 /* Apalis SD1 */ 180 iomux_v3_cfg_t const usdhc2_pads[] = { 181 MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 182 MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 183 MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 184 MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 185 MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 186 MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 187 MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ 188 # define GPIO_SD_CD IMX_GPIO_NR(6, 14) 189 }; 190 191 /* eMMC */ 192 iomux_v3_cfg_t const usdhc3_pads[] = { 193 MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 194 MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 195 MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 196 MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 197 MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 198 MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 199 MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 200 MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 201 MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 202 MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 203 MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), 204 }; 205 206 int mx6_rgmii_rework(struct phy_device *phydev) 207 { 208 /* control data pad skew - devaddr = 0x02, register = 0x04 */ 209 ksz9031_phy_extended_write(phydev, 0x02, 210 MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, 211 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 212 /* rx data pad skew - devaddr = 0x02, register = 0x05 */ 213 ksz9031_phy_extended_write(phydev, 0x02, 214 MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 215 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 216 /* tx data pad skew - devaddr = 0x02, register = 0x05 */ 217 ksz9031_phy_extended_write(phydev, 0x02, 218 MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 219 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 220 /* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */ 221 ksz9031_phy_extended_write(phydev, 0x02, 222 MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, 223 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF); 224 return 0; 225 } 226 227 iomux_v3_cfg_t const enet_pads[] = { 228 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 229 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 230 MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 231 MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 232 MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 233 MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 234 MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 235 MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 236 MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), 237 MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 238 MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 239 MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 240 MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 241 MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 242 MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 243 /* KSZ9031 PHY Reset */ 244 MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), 245 # define GPIO_ENET_PHY_RESET IMX_GPIO_NR(1, 25) 246 }; 247 248 static void setup_iomux_enet(void) 249 { 250 imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); 251 } 252 253 static int reset_enet_phy(struct mii_dev *bus) 254 { 255 /* Reset KSZ9031 PHY */ 256 gpio_direction_output(GPIO_ENET_PHY_RESET, 0); 257 mdelay(10); 258 gpio_set_value(GPIO_ENET_PHY_RESET, 1); 259 260 return 0; 261 } 262 263 /* mux the Apalis GPIO pins, so they can be used from the U-Boot cmdline */ 264 iomux_v3_cfg_t const gpio_pads[] = { 265 /* Apalis GPIO1 - GPIO8 */ 266 MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), 267 MX6_PAD_NANDF_D5__GPIO2_IO05 | MUX_PAD_CTRL(WEAK_PULLUP), 268 MX6_PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), 269 MX6_PAD_NANDF_D7__GPIO2_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), 270 MX6_PAD_NANDF_RB0__GPIO6_IO10 | MUX_PAD_CTRL(WEAK_PULLUP), 271 MX6_PAD_NANDF_WP_B__GPIO6_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), 272 MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(WEAK_PULLDOWN), 273 MX6_PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), 274 MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), 275 }; 276 277 static void setup_iomux_gpio(void) 278 { 279 imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads)); 280 } 281 282 iomux_v3_cfg_t const usb_pads[] = { 283 /* USBH_EN */ 284 MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), 285 # define GPIO_USBH_EN IMX_GPIO_NR(1, 0) 286 /* USB_VBUS_DET */ 287 MX6_PAD_EIM_D28__GPIO3_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), 288 # define GPIO_USB_VBUS_DET IMX_GPIO_NR(3, 28) 289 /* USBO1_ID */ 290 MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(WEAK_PULLUP), 291 /* USBO1_EN */ 292 MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL), 293 # define GPIO_USBO_EN IMX_GPIO_NR(3, 22) 294 }; 295 296 /* 297 * UARTs are used in DTE mode, switch the mode on all UARTs before 298 * any pinmuxing connects a (DCE) output to a transceiver output. 299 */ 300 #define UFCR 0x90 /* FIFO Control Register */ 301 #define UFCR_DCEDTE (1<<6) /* DCE=0 */ 302 303 static void setup_dtemode_uart(void) 304 { 305 setbits_le32((u32 *)(UART1_BASE + UFCR), UFCR_DCEDTE); 306 setbits_le32((u32 *)(UART2_BASE + UFCR), UFCR_DCEDTE); 307 setbits_le32((u32 *)(UART4_BASE + UFCR), UFCR_DCEDTE); 308 setbits_le32((u32 *)(UART5_BASE + UFCR), UFCR_DCEDTE); 309 } 310 static void setup_dcemode_uart(void) 311 { 312 clrbits_le32((u32 *)(UART1_BASE + UFCR), UFCR_DCEDTE); 313 clrbits_le32((u32 *)(UART2_BASE + UFCR), UFCR_DCEDTE); 314 clrbits_le32((u32 *)(UART4_BASE + UFCR), UFCR_DCEDTE); 315 clrbits_le32((u32 *)(UART5_BASE + UFCR), UFCR_DCEDTE); 316 } 317 318 static void setup_iomux_dte_uart(void) 319 { 320 setup_dtemode_uart(); 321 imx_iomux_v3_setup_multiple_pads(uart1_pads_dte, 322 ARRAY_SIZE(uart1_pads_dte)); 323 } 324 325 static void setup_iomux_dce_uart(void) 326 { 327 setup_dcemode_uart(); 328 imx_iomux_v3_setup_multiple_pads(uart1_pads_dce, 329 ARRAY_SIZE(uart1_pads_dce)); 330 } 331 332 #ifdef CONFIG_USB_EHCI_MX6 333 int board_ehci_hcd_init(int port) 334 { 335 imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); 336 return 0; 337 } 338 339 int board_ehci_power(int port, int on) 340 { 341 switch (port) { 342 case 0: 343 /* control OTG power */ 344 gpio_direction_output(GPIO_USBO_EN, on); 345 mdelay(100); 346 break; 347 case 1: 348 /* Control MXM USBH */ 349 gpio_direction_output(GPIO_USBH_EN, on); 350 mdelay(2); 351 /* Control onboard USB Hub VBUS */ 352 gpio_direction_output(GPIO_USB_VBUS_DET, on); 353 mdelay(100); 354 break; 355 default: 356 break; 357 } 358 return 0; 359 } 360 #endif 361 362 #ifdef CONFIG_FSL_ESDHC 363 /* use the following sequence: eMMC, MMC, SD */ 364 struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { 365 {USDHC3_BASE_ADDR}, 366 {USDHC1_BASE_ADDR}, 367 {USDHC2_BASE_ADDR}, 368 }; 369 370 int board_mmc_getcd(struct mmc *mmc) 371 { 372 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 373 int ret = true; /* default: assume inserted */ 374 375 switch (cfg->esdhc_base) { 376 case USDHC1_BASE_ADDR: 377 gpio_direction_input(GPIO_MMC_CD); 378 ret = !gpio_get_value(GPIO_MMC_CD); 379 break; 380 case USDHC2_BASE_ADDR: 381 gpio_direction_input(GPIO_SD_CD); 382 ret = !gpio_get_value(GPIO_SD_CD); 383 break; 384 } 385 386 return ret; 387 } 388 389 int board_mmc_init(bd_t *bis) 390 { 391 #ifndef CONFIG_SPL_BUILD 392 s32 status = 0; 393 u32 index = 0; 394 395 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 396 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 397 usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 398 399 usdhc_cfg[0].max_bus_width = 8; 400 usdhc_cfg[1].max_bus_width = 8; 401 usdhc_cfg[2].max_bus_width = 4; 402 403 for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { 404 switch (index) { 405 case 0: 406 imx_iomux_v3_setup_multiple_pads( 407 usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); 408 break; 409 case 1: 410 imx_iomux_v3_setup_multiple_pads( 411 usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); 412 break; 413 case 2: 414 imx_iomux_v3_setup_multiple_pads( 415 usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); 416 break; 417 default: 418 printf("Warning: you configured more USDHC controllers (%d) then supported by the board (%d)\n", 419 index + 1, CONFIG_SYS_FSL_USDHC_NUM); 420 return status; 421 } 422 423 status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]); 424 } 425 426 return status; 427 #else 428 struct src *psrc = (struct src *)SRC_BASE_ADDR; 429 unsigned reg = readl(&psrc->sbmr1) >> 11; 430 /* 431 * Upon reading BOOT_CFG register the following map is done: 432 * Bit 11 and 12 of BOOT_CFG register can determine the current 433 * mmc port 434 * 0x1 SD1 435 * 0x2 SD2 436 * 0x3 SD4 437 */ 438 439 switch (reg & 0x3) { 440 case 0x0: 441 imx_iomux_v3_setup_multiple_pads( 442 usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); 443 usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR; 444 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 445 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; 446 break; 447 case 0x1: 448 imx_iomux_v3_setup_multiple_pads( 449 usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); 450 usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR; 451 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 452 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; 453 break; 454 case 0x2: 455 imx_iomux_v3_setup_multiple_pads( 456 usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); 457 usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR; 458 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 459 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; 460 break; 461 default: 462 puts("MMC boot device not available"); 463 } 464 465 return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); 466 #endif 467 } 468 #endif 469 470 int board_phy_config(struct phy_device *phydev) 471 { 472 mx6_rgmii_rework(phydev); 473 if (phydev->drv->config) 474 phydev->drv->config(phydev); 475 476 return 0; 477 } 478 479 int board_eth_init(bd_t *bis) 480 { 481 uint32_t base = IMX_FEC_BASE; 482 struct mii_dev *bus = NULL; 483 struct phy_device *phydev = NULL; 484 int ret; 485 486 setup_iomux_enet(); 487 488 #ifdef CONFIG_FEC_MXC 489 bus = fec_get_miibus(base, -1); 490 if (!bus) 491 return 0; 492 bus->reset = reset_enet_phy; 493 /* scan PHY 4,5,6,7 */ 494 phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII); 495 if (!phydev) { 496 free(bus); 497 puts("no PHY found\n"); 498 return 0; 499 } 500 printf("using PHY at %d\n", phydev->addr); 501 ret = fec_probe(bis, -1, base, bus, phydev); 502 if (ret) { 503 printf("FEC MXC: %s:failed\n", __func__); 504 free(phydev); 505 free(bus); 506 } 507 #endif 508 return 0; 509 } 510 511 static iomux_v3_cfg_t const pwr_intb_pads[] = { 512 /* 513 * the bootrom sets the iomux to vselect, potentially connecting 514 * two outputs. Set this back to GPIO 515 */ 516 MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL) 517 }; 518 519 #if defined(CONFIG_VIDEO_IPUV3) 520 521 static iomux_v3_cfg_t const backlight_pads[] = { 522 /* Backlight on RGB connector: J15 */ 523 MX6_PAD_EIM_DA13__GPIO3_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL), 524 #define RGB_BACKLIGHT_GP IMX_GPIO_NR(3, 13) 525 /* additional CPU pin on BKL_PWM, keep in tristate */ 526 MX6_PAD_EIM_DA14__GPIO3_IO14 | MUX_PAD_CTRL(TRISTATE), 527 /* Backlight PWM, used as GPIO in U-Boot */ 528 MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), 529 #define RGB_BACKLIGHTPWM_GP IMX_GPIO_NR(2, 10) 530 /* buffer output enable 0: buffer enabled */ 531 MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), 532 #define RGB_BACKLIGHTPWM_OE IMX_GPIO_NR(5, 2) 533 /* PSAVE# integrated VDAC */ 534 MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), 535 #define VGA_PSAVE_NOT_GP IMX_GPIO_NR(6, 31) 536 }; 537 538 static iomux_v3_cfg_t const rgb_pads[] = { 539 MX6_PAD_EIM_A16__IPU1_DI1_DISP_CLK | MUX_PAD_CTRL(OUTPUT_RGB), 540 MX6_PAD_EIM_DA10__IPU1_DI1_PIN15 | MUX_PAD_CTRL(OUTPUT_RGB), 541 MX6_PAD_EIM_DA11__IPU1_DI1_PIN02 | MUX_PAD_CTRL(OUTPUT_RGB), 542 MX6_PAD_EIM_DA12__IPU1_DI1_PIN03 | MUX_PAD_CTRL(OUTPUT_RGB), 543 MX6_PAD_EIM_DA9__IPU1_DISP1_DATA00 | MUX_PAD_CTRL(OUTPUT_RGB), 544 MX6_PAD_EIM_DA8__IPU1_DISP1_DATA01 | MUX_PAD_CTRL(OUTPUT_RGB), 545 MX6_PAD_EIM_DA7__IPU1_DISP1_DATA02 | MUX_PAD_CTRL(OUTPUT_RGB), 546 MX6_PAD_EIM_DA6__IPU1_DISP1_DATA03 | MUX_PAD_CTRL(OUTPUT_RGB), 547 MX6_PAD_EIM_DA5__IPU1_DISP1_DATA04 | MUX_PAD_CTRL(OUTPUT_RGB), 548 MX6_PAD_EIM_DA4__IPU1_DISP1_DATA05 | MUX_PAD_CTRL(OUTPUT_RGB), 549 MX6_PAD_EIM_DA3__IPU1_DISP1_DATA06 | MUX_PAD_CTRL(OUTPUT_RGB), 550 MX6_PAD_EIM_DA2__IPU1_DISP1_DATA07 | MUX_PAD_CTRL(OUTPUT_RGB), 551 MX6_PAD_EIM_DA1__IPU1_DISP1_DATA08 | MUX_PAD_CTRL(OUTPUT_RGB), 552 MX6_PAD_EIM_DA0__IPU1_DISP1_DATA09 | MUX_PAD_CTRL(OUTPUT_RGB), 553 MX6_PAD_EIM_EB1__IPU1_DISP1_DATA10 | MUX_PAD_CTRL(OUTPUT_RGB), 554 MX6_PAD_EIM_EB0__IPU1_DISP1_DATA11 | MUX_PAD_CTRL(OUTPUT_RGB), 555 MX6_PAD_EIM_A17__IPU1_DISP1_DATA12 | MUX_PAD_CTRL(OUTPUT_RGB), 556 MX6_PAD_EIM_A18__IPU1_DISP1_DATA13 | MUX_PAD_CTRL(OUTPUT_RGB), 557 MX6_PAD_EIM_A19__IPU1_DISP1_DATA14 | MUX_PAD_CTRL(OUTPUT_RGB), 558 MX6_PAD_EIM_A20__IPU1_DISP1_DATA15 | MUX_PAD_CTRL(OUTPUT_RGB), 559 MX6_PAD_EIM_A21__IPU1_DISP1_DATA16 | MUX_PAD_CTRL(OUTPUT_RGB), 560 MX6_PAD_EIM_A22__IPU1_DISP1_DATA17 | MUX_PAD_CTRL(OUTPUT_RGB), 561 MX6_PAD_EIM_A23__IPU1_DISP1_DATA18 | MUX_PAD_CTRL(OUTPUT_RGB), 562 MX6_PAD_EIM_A24__IPU1_DISP1_DATA19 | MUX_PAD_CTRL(OUTPUT_RGB), 563 MX6_PAD_EIM_D26__IPU1_DISP1_DATA22 | MUX_PAD_CTRL(OUTPUT_RGB), 564 MX6_PAD_EIM_D27__IPU1_DISP1_DATA23 | MUX_PAD_CTRL(OUTPUT_RGB), 565 MX6_PAD_EIM_D30__IPU1_DISP1_DATA21 | MUX_PAD_CTRL(OUTPUT_RGB), 566 MX6_PAD_EIM_D31__IPU1_DISP1_DATA20 | MUX_PAD_CTRL(OUTPUT_RGB), 567 }; 568 569 static void do_enable_hdmi(struct display_info_t const *dev) 570 { 571 imx_enable_hdmi_phy(); 572 } 573 574 static int detect_i2c(struct display_info_t const *dev) 575 { 576 return (0 == i2c_set_bus_num(dev->bus)) && 577 (0 == i2c_probe(dev->addr)); 578 } 579 580 static void enable_lvds(struct display_info_t const *dev) 581 { 582 struct iomuxc *iomux = (struct iomuxc *) 583 IOMUXC_BASE_ADDR; 584 u32 reg = readl(&iomux->gpr[2]); 585 reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT; 586 writel(reg, &iomux->gpr[2]); 587 gpio_direction_output(RGB_BACKLIGHT_GP, 1); 588 gpio_direction_output(RGB_BACKLIGHTPWM_GP, 0); 589 gpio_direction_output(RGB_BACKLIGHTPWM_OE, 0); 590 } 591 592 static void enable_rgb(struct display_info_t const *dev) 593 { 594 imx_iomux_v3_setup_multiple_pads( 595 rgb_pads, 596 ARRAY_SIZE(rgb_pads)); 597 gpio_direction_output(RGB_BACKLIGHT_GP, 1); 598 gpio_direction_output(RGB_BACKLIGHTPWM_GP, 0); 599 gpio_direction_output(RGB_BACKLIGHTPWM_OE, 0); 600 } 601 602 static int detect_default(struct display_info_t const *dev) 603 { 604 (void) dev; 605 return 1; 606 } 607 608 struct display_info_t const displays[] = {{ 609 .bus = -1, 610 .addr = 0, 611 .pixfmt = IPU_PIX_FMT_RGB24, 612 .detect = detect_hdmi, 613 .enable = do_enable_hdmi, 614 .mode = { 615 .name = "HDMI", 616 .refresh = 60, 617 .xres = 1024, 618 .yres = 768, 619 .pixclock = 15385, 620 .left_margin = 220, 621 .right_margin = 40, 622 .upper_margin = 21, 623 .lower_margin = 7, 624 .hsync_len = 60, 625 .vsync_len = 10, 626 .sync = FB_SYNC_EXT, 627 .vmode = FB_VMODE_NONINTERLACED 628 } }, { 629 .bus = -1, 630 .addr = 0, 631 .di = 1, 632 .pixfmt = IPU_PIX_FMT_RGB24, 633 .detect = detect_default, 634 .enable = enable_rgb, 635 .mode = { 636 .name = "vga-rgb", 637 .refresh = 60, 638 .xres = 640, 639 .yres = 480, 640 .pixclock = 33000, 641 .left_margin = 48, 642 .right_margin = 16, 643 .upper_margin = 31, 644 .lower_margin = 11, 645 .hsync_len = 96, 646 .vsync_len = 2, 647 .sync = 0, 648 .vmode = FB_VMODE_NONINTERLACED 649 } }, { 650 .bus = -1, 651 .addr = 0, 652 .di = 1, 653 .pixfmt = IPU_PIX_FMT_RGB24, 654 .enable = enable_rgb, 655 .mode = { 656 .name = "wvga-rgb", 657 .refresh = 60, 658 .xres = 800, 659 .yres = 480, 660 .pixclock = 25000, 661 .left_margin = 40, 662 .right_margin = 88, 663 .upper_margin = 33, 664 .lower_margin = 10, 665 .hsync_len = 128, 666 .vsync_len = 2, 667 .sync = 0, 668 .vmode = FB_VMODE_NONINTERLACED 669 } }, { 670 .bus = -1, 671 .addr = 0, 672 .pixfmt = IPU_PIX_FMT_LVDS666, 673 .detect = detect_i2c, 674 .enable = enable_lvds, 675 .mode = { 676 .name = "wsvga-lvds", 677 .refresh = 60, 678 .xres = 1024, 679 .yres = 600, 680 .pixclock = 15385, 681 .left_margin = 220, 682 .right_margin = 40, 683 .upper_margin = 21, 684 .lower_margin = 7, 685 .hsync_len = 60, 686 .vsync_len = 10, 687 .sync = FB_SYNC_EXT, 688 .vmode = FB_VMODE_NONINTERLACED 689 } } }; 690 size_t display_count = ARRAY_SIZE(displays); 691 692 static void setup_display(void) 693 { 694 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 695 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 696 int reg; 697 698 enable_ipu_clock(); 699 imx_setup_hdmi(); 700 /* Turn on LDB0,IPU,IPU DI0 clocks */ 701 reg = __raw_readl(&mxc_ccm->CCGR3); 702 reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; 703 writel(reg, &mxc_ccm->CCGR3); 704 705 /* set LDB0, LDB1 clk select to 011/011 */ 706 reg = readl(&mxc_ccm->cs2cdr); 707 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 708 |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 709 reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) 710 |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); 711 writel(reg, &mxc_ccm->cs2cdr); 712 713 reg = readl(&mxc_ccm->cscmr2); 714 reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; 715 writel(reg, &mxc_ccm->cscmr2); 716 717 reg = readl(&mxc_ccm->chsccdr); 718 reg |= (CHSCCDR_CLK_SEL_LDB_DI0 719 <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); 720 writel(reg, &mxc_ccm->chsccdr); 721 722 reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES 723 |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH 724 |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW 725 |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG 726 |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT 727 |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG 728 |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT 729 |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED 730 |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; 731 writel(reg, &iomux->gpr[2]); 732 733 reg = readl(&iomux->gpr[3]); 734 reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK 735 |IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) 736 | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 737 <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); 738 writel(reg, &iomux->gpr[3]); 739 740 /* backlight unconditionally on for now */ 741 imx_iomux_v3_setup_multiple_pads(backlight_pads, 742 ARRAY_SIZE(backlight_pads)); 743 /* use 0 for EDT 7", use 1 for LG fullHD panel */ 744 gpio_direction_output(RGB_BACKLIGHTPWM_GP, 0); 745 gpio_direction_output(RGB_BACKLIGHTPWM_OE, 0); 746 gpio_direction_output(RGB_BACKLIGHT_GP, 1); 747 } 748 749 /* 750 * Backlight off before OS handover 751 */ 752 void board_preboot_os(void) 753 { 754 gpio_direction_output(RGB_BACKLIGHTPWM_GP, 1); 755 gpio_direction_output(RGB_BACKLIGHT_GP, 0); 756 } 757 #endif /* defined(CONFIG_VIDEO_IPUV3) */ 758 759 int board_early_init_f(void) 760 { 761 imx_iomux_v3_setup_multiple_pads(pwr_intb_pads, 762 ARRAY_SIZE(pwr_intb_pads)); 763 #ifndef CONFIG_TDX_APALIS_IMX6_V1_0 764 setup_iomux_dte_uart(); 765 #else 766 setup_iomux_dce_uart(); 767 #endif 768 return 0; 769 } 770 771 /* 772 * Do not overwrite the console 773 * Use always serial for U-Boot console 774 */ 775 int overwrite_console(void) 776 { 777 return 1; 778 } 779 780 int board_init(void) 781 { 782 /* address of boot parameters */ 783 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 784 785 setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); 786 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info_loc); 787 setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); 788 789 #if defined(CONFIG_VIDEO_IPUV3) 790 setup_display(); 791 #endif 792 793 #ifdef CONFIG_TDX_CMD_IMX_MFGR 794 (void) pmic_init(); 795 #endif 796 797 #ifdef CONFIG_SATA 798 setup_sata(); 799 #endif 800 801 setup_iomux_gpio(); 802 803 return 0; 804 } 805 806 #ifdef CONFIG_BOARD_LATE_INIT 807 int board_late_init(void) 808 { 809 #if defined(CONFIG_REVISION_TAG) && \ 810 defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG) 811 char env_str[256]; 812 u32 rev; 813 814 rev = get_board_rev(); 815 snprintf(env_str, ARRAY_SIZE(env_str), "%.4x", rev); 816 env_set("board_rev", env_str); 817 818 #ifndef CONFIG_TDX_APALIS_IMX6_V1_0 819 if ((rev & 0xfff0) == 0x0100) { 820 char *fdt_env; 821 822 /* reconfigure the UART to DCE mode dynamically if on V1.0 HW */ 823 setup_iomux_dce_uart(); 824 825 /* if using the default device tree, use version for V1.0 HW */ 826 fdt_env = env_get("fdt_file"); 827 if ((fdt_env != NULL) && (strcmp(FDT_FILE, fdt_env) == 0)) { 828 env_set("fdt_file", FDT_FILE_V1_0); 829 printf("patching fdt_file to " FDT_FILE_V1_0 "\n"); 830 #ifndef CONFIG_ENV_IS_NOWHERE 831 env_save(); 832 #endif 833 } 834 } 835 #endif /* CONFIG_TDX_APALIS_IMX6_V1_0 */ 836 #endif /* CONFIG_REVISION_TAG */ 837 838 return 0; 839 } 840 #endif /* CONFIG_BOARD_LATE_INIT */ 841 842 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_SYSTEM_SETUP) 843 int ft_system_setup(void *blob, bd_t *bd) 844 { 845 return 0; 846 } 847 #endif 848 849 int checkboard(void) 850 { 851 char it[] = " IT"; 852 int minc, maxc; 853 854 switch (get_cpu_temp_grade(&minc, &maxc)) { 855 case TEMP_AUTOMOTIVE: 856 case TEMP_INDUSTRIAL: 857 break; 858 case TEMP_EXTCOMMERCIAL: 859 default: 860 it[0] = 0; 861 }; 862 printf("Model: Toradex Apalis iMX6 %s %s%s\n", 863 is_cpu_type(MXC_CPU_MX6D) ? "Dual" : "Quad", 864 (gd->ram_size == 0x80000000) ? "2GB" : 865 (gd->ram_size == 0x40000000) ? "1GB" : "512MB", it); 866 return 0; 867 } 868 869 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) 870 int ft_board_setup(void *blob, bd_t *bd) 871 { 872 return ft_common_board_setup(blob, bd); 873 } 874 #endif 875 876 #ifdef CONFIG_CMD_BMODE 877 static const struct boot_mode board_boot_modes[] = { 878 /* 4-bit bus width */ 879 {"mmc", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)}, 880 {"sd", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, 881 {NULL, 0}, 882 }; 883 #endif 884 885 int misc_init_r(void) 886 { 887 #ifdef CONFIG_CMD_BMODE 888 add_board_boot_modes(board_boot_modes); 889 #endif 890 return 0; 891 } 892 893 #ifdef CONFIG_LDO_BYPASS_CHECK 894 /* TODO, use external pmic, for now always ldo_enable */ 895 void ldo_mode_set(int ldo_bypass) 896 { 897 return; 898 } 899 #endif 900 901 #ifdef CONFIG_SPL_BUILD 902 #include <spl.h> 903 #include <linux/libfdt.h> 904 #include "asm/arch/mx6q-ddr.h" 905 #include "asm/arch/iomux.h" 906 #include "asm/arch/crm_regs.h" 907 908 static int mx6_com_dcd_table[] = { 909 /* ddr-setup.cfg */ 910 MX6_IOM_DRAM_SDQS0, 0x00000030, 911 MX6_IOM_DRAM_SDQS1, 0x00000030, 912 MX6_IOM_DRAM_SDQS2, 0x00000030, 913 MX6_IOM_DRAM_SDQS3, 0x00000030, 914 MX6_IOM_DRAM_SDQS4, 0x00000030, 915 MX6_IOM_DRAM_SDQS5, 0x00000030, 916 MX6_IOM_DRAM_SDQS6, 0x00000030, 917 MX6_IOM_DRAM_SDQS7, 0x00000030, 918 919 MX6_IOM_GRP_B0DS, 0x00000030, 920 MX6_IOM_GRP_B1DS, 0x00000030, 921 MX6_IOM_GRP_B2DS, 0x00000030, 922 MX6_IOM_GRP_B3DS, 0x00000030, 923 MX6_IOM_GRP_B4DS, 0x00000030, 924 MX6_IOM_GRP_B5DS, 0x00000030, 925 MX6_IOM_GRP_B6DS, 0x00000030, 926 MX6_IOM_GRP_B7DS, 0x00000030, 927 MX6_IOM_GRP_ADDDS, 0x00000030, 928 /* 40 Ohm drive strength for cs0/1,sdba2,cke0/1,sdwe */ 929 MX6_IOM_GRP_CTLDS, 0x00000030, 930 931 MX6_IOM_DRAM_DQM0, 0x00020030, 932 MX6_IOM_DRAM_DQM1, 0x00020030, 933 MX6_IOM_DRAM_DQM2, 0x00020030, 934 MX6_IOM_DRAM_DQM3, 0x00020030, 935 MX6_IOM_DRAM_DQM4, 0x00020030, 936 MX6_IOM_DRAM_DQM5, 0x00020030, 937 MX6_IOM_DRAM_DQM6, 0x00020030, 938 MX6_IOM_DRAM_DQM7, 0x00020030, 939 940 MX6_IOM_DRAM_CAS, 0x00020030, 941 MX6_IOM_DRAM_RAS, 0x00020030, 942 MX6_IOM_DRAM_SDCLK_0, 0x00020030, 943 MX6_IOM_DRAM_SDCLK_1, 0x00020030, 944 945 MX6_IOM_DRAM_RESET, 0x00020030, 946 MX6_IOM_DRAM_SDCKE0, 0x00003000, 947 MX6_IOM_DRAM_SDCKE1, 0x00003000, 948 949 MX6_IOM_DRAM_SDODT0, 0x00003030, 950 MX6_IOM_DRAM_SDODT1, 0x00003030, 951 952 /* (differential input) */ 953 MX6_IOM_DDRMODE_CTL, 0x00020000, 954 /* (differential input) */ 955 MX6_IOM_GRP_DDRMODE, 0x00020000, 956 /* disable ddr pullups */ 957 MX6_IOM_GRP_DDRPKE, 0x00000000, 958 MX6_IOM_DRAM_SDBA2, 0x00000000, 959 /* 40 Ohm drive strength for cs0/1,sdba2,cke0/1,sdwe */ 960 MX6_IOM_GRP_DDR_TYPE, 0x000C0000, 961 962 /* Read data DQ Byte0-3 delay */ 963 MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333, 964 MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333, 965 MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333, 966 MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333, 967 MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333, 968 MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333, 969 MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333, 970 MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333, 971 972 /* 973 * MDMISC mirroring interleaved (row/bank/col) 974 */ 975 MX6_MMDC_P0_MDMISC, 0x00081740, 976 977 /* 978 * MDSCR con_req 979 */ 980 MX6_MMDC_P0_MDSCR, 0x00008000, 981 982 /* 1066mhz_4x128mx16.cfg */ 983 984 MX6_MMDC_P0_MDPDC, 0x00020036, 985 MX6_MMDC_P0_MDCFG0, 0x555A7954, 986 MX6_MMDC_P0_MDCFG1, 0xDB328F64, 987 MX6_MMDC_P0_MDCFG2, 0x01FF00DB, 988 MX6_MMDC_P0_MDRWD, 0x000026D2, 989 MX6_MMDC_P0_MDOR, 0x005A1023, 990 MX6_MMDC_P0_MDOTC, 0x09555050, 991 MX6_MMDC_P0_MDPDC, 0x00025576, 992 MX6_MMDC_P0_MDASP, 0x00000027, 993 MX6_MMDC_P0_MDCTL, 0x831A0000, 994 MX6_MMDC_P0_MDSCR, 0x04088032, 995 MX6_MMDC_P0_MDSCR, 0x00008033, 996 MX6_MMDC_P0_MDSCR, 0x00428031, 997 MX6_MMDC_P0_MDSCR, 0x19308030, 998 MX6_MMDC_P0_MDSCR, 0x04008040, 999 MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003, 1000 MX6_MMDC_P1_MPZQHWCTRL, 0xA1390003, 1001 MX6_MMDC_P0_MDREF, 0x00005800, 1002 MX6_MMDC_P0_MPODTCTRL, 0x00000000, 1003 MX6_MMDC_P1_MPODTCTRL, 0x00000000, 1004 1005 MX6_MMDC_P0_MPDGCTRL0, 0x432A0338, 1006 MX6_MMDC_P0_MPDGCTRL1, 0x03260324, 1007 MX6_MMDC_P1_MPDGCTRL0, 0x43340344, 1008 MX6_MMDC_P1_MPDGCTRL1, 0x031E027C, 1009 1010 MX6_MMDC_P0_MPRDDLCTL, 0x33272D2E, 1011 MX6_MMDC_P1_MPRDDLCTL, 0x2F312B37, 1012 1013 MX6_MMDC_P0_MPWRDLCTL, 0x3A35433C, 1014 MX6_MMDC_P1_MPWRDLCTL, 0x4336453F, 1015 1016 MX6_MMDC_P0_MPWLDECTRL0, 0x0009000E, 1017 MX6_MMDC_P0_MPWLDECTRL1, 0x0018000B, 1018 MX6_MMDC_P1_MPWLDECTRL0, 0x00060015, 1019 MX6_MMDC_P1_MPWLDECTRL1, 0x0006000E, 1020 1021 MX6_MMDC_P0_MPMUR0, 0x00000800, 1022 MX6_MMDC_P1_MPMUR0, 0x00000800, 1023 MX6_MMDC_P0_MDSCR, 0x00000000, 1024 MX6_MMDC_P0_MAPSR, 0x00011006, 1025 }; 1026 1027 static int mx6_it_dcd_table[] = { 1028 /* ddr-setup.cfg */ 1029 MX6_IOM_DRAM_SDQS0, 0x00000030, 1030 MX6_IOM_DRAM_SDQS1, 0x00000030, 1031 MX6_IOM_DRAM_SDQS2, 0x00000030, 1032 MX6_IOM_DRAM_SDQS3, 0x00000030, 1033 MX6_IOM_DRAM_SDQS4, 0x00000030, 1034 MX6_IOM_DRAM_SDQS5, 0x00000030, 1035 MX6_IOM_DRAM_SDQS6, 0x00000030, 1036 MX6_IOM_DRAM_SDQS7, 0x00000030, 1037 1038 MX6_IOM_GRP_B0DS, 0x00000030, 1039 MX6_IOM_GRP_B1DS, 0x00000030, 1040 MX6_IOM_GRP_B2DS, 0x00000030, 1041 MX6_IOM_GRP_B3DS, 0x00000030, 1042 MX6_IOM_GRP_B4DS, 0x00000030, 1043 MX6_IOM_GRP_B5DS, 0x00000030, 1044 MX6_IOM_GRP_B6DS, 0x00000030, 1045 MX6_IOM_GRP_B7DS, 0x00000030, 1046 MX6_IOM_GRP_ADDDS, 0x00000030, 1047 /* 40 Ohm drive strength for cs0/1,sdba2,cke0/1,sdwe */ 1048 MX6_IOM_GRP_CTLDS, 0x00000030, 1049 1050 MX6_IOM_DRAM_DQM0, 0x00020030, 1051 MX6_IOM_DRAM_DQM1, 0x00020030, 1052 MX6_IOM_DRAM_DQM2, 0x00020030, 1053 MX6_IOM_DRAM_DQM3, 0x00020030, 1054 MX6_IOM_DRAM_DQM4, 0x00020030, 1055 MX6_IOM_DRAM_DQM5, 0x00020030, 1056 MX6_IOM_DRAM_DQM6, 0x00020030, 1057 MX6_IOM_DRAM_DQM7, 0x00020030, 1058 1059 MX6_IOM_DRAM_CAS, 0x00020030, 1060 MX6_IOM_DRAM_RAS, 0x00020030, 1061 MX6_IOM_DRAM_SDCLK_0, 0x00020030, 1062 MX6_IOM_DRAM_SDCLK_1, 0x00020030, 1063 1064 MX6_IOM_DRAM_RESET, 0x00020030, 1065 MX6_IOM_DRAM_SDCKE0, 0x00003000, 1066 MX6_IOM_DRAM_SDCKE1, 0x00003000, 1067 1068 MX6_IOM_DRAM_SDODT0, 0x00003030, 1069 MX6_IOM_DRAM_SDODT1, 0x00003030, 1070 1071 /* (differential input) */ 1072 MX6_IOM_DDRMODE_CTL, 0x00020000, 1073 /* (differential input) */ 1074 MX6_IOM_GRP_DDRMODE, 0x00020000, 1075 /* disable ddr pullups */ 1076 MX6_IOM_GRP_DDRPKE, 0x00000000, 1077 MX6_IOM_DRAM_SDBA2, 0x00000000, 1078 /* 40 Ohm drive strength for cs0/1,sdba2,cke0/1,sdwe */ 1079 MX6_IOM_GRP_DDR_TYPE, 0x000C0000, 1080 1081 /* Read data DQ Byte0-3 delay */ 1082 MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333, 1083 MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333, 1084 MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333, 1085 MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333, 1086 MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333, 1087 MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333, 1088 MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333, 1089 MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333, 1090 1091 /* 1092 * MDMISC mirroring interleaved (row/bank/col) 1093 */ 1094 MX6_MMDC_P0_MDMISC, 0x00081740, 1095 1096 /* 1097 * MDSCR con_req 1098 */ 1099 MX6_MMDC_P0_MDSCR, 0x00008000, 1100 1101 /* 1066mhz_4x256mx16.cfg */ 1102 1103 MX6_MMDC_P0_MDPDC, 0x00020036, 1104 MX6_MMDC_P0_MDCFG0, 0x898E78f5, 1105 MX6_MMDC_P0_MDCFG1, 0xff328f64, 1106 MX6_MMDC_P0_MDCFG2, 0x01FF00DB, 1107 MX6_MMDC_P0_MDRWD, 0x000026D2, 1108 MX6_MMDC_P0_MDOR, 0x008E1023, 1109 MX6_MMDC_P0_MDOTC, 0x09444040, 1110 MX6_MMDC_P0_MDPDC, 0x00025576, 1111 MX6_MMDC_P0_MDASP, 0x00000047, 1112 MX6_MMDC_P0_MDCTL, 0x841A0000, 1113 MX6_MMDC_P0_MDSCR, 0x02888032, 1114 MX6_MMDC_P0_MDSCR, 0x00008033, 1115 MX6_MMDC_P0_MDSCR, 0x00048031, 1116 MX6_MMDC_P0_MDSCR, 0x19408030, 1117 MX6_MMDC_P0_MDSCR, 0x04008040, 1118 MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003, 1119 MX6_MMDC_P1_MPZQHWCTRL, 0xA1390003, 1120 MX6_MMDC_P0_MDREF, 0x00007800, 1121 MX6_MMDC_P0_MPODTCTRL, 0x00022227, 1122 MX6_MMDC_P1_MPODTCTRL, 0x00022227, 1123 1124 MX6_MMDC_P0_MPDGCTRL0, 0x03300338, 1125 MX6_MMDC_P0_MPDGCTRL1, 0x03240324, 1126 MX6_MMDC_P1_MPDGCTRL0, 0x03440350, 1127 MX6_MMDC_P1_MPDGCTRL1, 0x032C0308, 1128 1129 MX6_MMDC_P0_MPRDDLCTL, 0x40363C3E, 1130 MX6_MMDC_P1_MPRDDLCTL, 0x3C3E3C46, 1131 1132 MX6_MMDC_P0_MPWRDLCTL, 0x403E463E, 1133 MX6_MMDC_P1_MPWRDLCTL, 0x4A384C46, 1134 1135 MX6_MMDC_P0_MPWLDECTRL0, 0x0009000E, 1136 MX6_MMDC_P0_MPWLDECTRL1, 0x0018000B, 1137 MX6_MMDC_P1_MPWLDECTRL0, 0x00060015, 1138 MX6_MMDC_P1_MPWLDECTRL1, 0x0006000E, 1139 1140 MX6_MMDC_P0_MPMUR0, 0x00000800, 1141 MX6_MMDC_P1_MPMUR0, 0x00000800, 1142 MX6_MMDC_P0_MDSCR, 0x00000000, 1143 MX6_MMDC_P0_MAPSR, 0x00011006, 1144 }; 1145 1146 1147 static void ccgr_init(void) 1148 { 1149 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 1150 1151 writel(0x00C03F3F, &ccm->CCGR0); 1152 writel(0x0030FC03, &ccm->CCGR1); 1153 writel(0x0FFFFFF3, &ccm->CCGR2); 1154 writel(0x3FF0300F, &ccm->CCGR3); 1155 writel(0x00FFF300, &ccm->CCGR4); 1156 writel(0x0F0000F3, &ccm->CCGR5); 1157 writel(0x000003FF, &ccm->CCGR6); 1158 1159 /* 1160 * Setup CCM_CCOSR register as follows: 1161 * 1162 * cko1_en = 1 --> CKO1 enabled 1163 * cko1_div = 111 --> divide by 8 1164 * cko1_sel = 1011 --> ahb_clk_root 1165 * 1166 * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz 1167 */ 1168 writel(0x000000FB, &ccm->ccosr); 1169 } 1170 1171 static void ddr_init(int *table, int size) 1172 { 1173 int i; 1174 1175 for (i = 0; i < size / 2 ; i++) 1176 writel(table[2 * i + 1], table[2 * i]); 1177 } 1178 1179 static void spl_dram_init(void) 1180 { 1181 int minc, maxc; 1182 1183 switch (get_cpu_temp_grade(&minc, &maxc)) { 1184 case TEMP_COMMERCIAL: 1185 case TEMP_EXTCOMMERCIAL: 1186 puts("Commercial temperature grade DDR3 timings.\n"); 1187 ddr_init(mx6_com_dcd_table, ARRAY_SIZE(mx6_com_dcd_table)); 1188 break; 1189 case TEMP_INDUSTRIAL: 1190 case TEMP_AUTOMOTIVE: 1191 default: 1192 puts("Industrial temperature grade DDR3 timings.\n"); 1193 ddr_init(mx6_it_dcd_table, ARRAY_SIZE(mx6_it_dcd_table)); 1194 break; 1195 }; 1196 udelay(100); 1197 } 1198 1199 void board_init_f(ulong dummy) 1200 { 1201 /* setup AIPS and disable watchdog */ 1202 arch_cpu_init(); 1203 1204 ccgr_init(); 1205 gpr_init(); 1206 1207 /* iomux and setup of i2c */ 1208 board_early_init_f(); 1209 1210 /* setup GP timer */ 1211 timer_init(); 1212 1213 /* UART clocks enabled and gd valid - init serial console */ 1214 preloader_console_init(); 1215 1216 #ifndef CONFIG_TDX_APALIS_IMX6_V1_0 1217 /* Make sure we use dte mode */ 1218 setup_dtemode_uart(); 1219 #endif 1220 1221 /* DDR initialization */ 1222 spl_dram_init(); 1223 1224 /* Clear the BSS. */ 1225 memset(__bss_start, 0, __bss_end - __bss_start); 1226 1227 /* load/boot image from boot device */ 1228 board_init_r(NULL, 0); 1229 } 1230 1231 void reset_cpu(ulong addr) 1232 { 1233 } 1234 1235 #endif 1236 1237 static struct mxc_serial_platdata mxc_serial_plat = { 1238 .reg = (struct mxc_uart *)UART1_BASE, 1239 .use_dte = true, 1240 }; 1241 1242 U_BOOT_DEVICE(mxc_serial) = { 1243 .name = "serial_mxc", 1244 .platdata = &mxc_serial_plat, 1245 }; 1246