1 /*
2  * (C) Copyright 2004-2008
3  * Texas Instruments, <www.ti.com>
4  *
5  * Author :
6  *	Sunil Kumar <sunilsaini05@gmail.com>
7  *	Shashi Ranjan <shashiranjanmca05@gmail.com>
8  *
9  * (C) Copyright 2009
10  * Frederik Kriewitz <frederik@kriewitz.eu>
11  *
12  * Derived from Beagle Board and 3430 SDP code by
13  *	Richard Woodruff <r-woodruff2@ti.com>
14  *	Syed Mohammed Khasim <khasim@ti.com>
15  *
16  *
17  * SPDX-License-Identifier:	GPL-2.0+
18  */
19 #include <common.h>
20 #include <dm.h>
21 #include <ns16550.h>
22 #include <twl4030.h>
23 #include <asm/io.h>
24 #include <asm/arch/mmc_host_def.h>
25 #include <asm/arch/mux.h>
26 #include <asm/arch/sys_proto.h>
27 #include <asm/arch/mem.h>
28 #include <asm/mach-types.h>
29 #include "devkit8000.h"
30 #include <asm/gpio.h>
31 #ifdef CONFIG_DRIVER_DM9000
32 #include <net.h>
33 #include <netdev.h>
34 #endif
35 
36 DECLARE_GLOBAL_DATA_PTR;
37 
38 static u32 gpmc_net_config[GPMC_MAX_REG] = {
39 	NET_GPMC_CONFIG1,
40 	NET_GPMC_CONFIG2,
41 	NET_GPMC_CONFIG3,
42 	NET_GPMC_CONFIG4,
43 	NET_GPMC_CONFIG5,
44 	NET_GPMC_CONFIG6,
45 	0
46 };
47 
48 static const struct ns16550_platdata devkit8000_serial = {
49 	.base = OMAP34XX_UART3,
50 	.reg_shift = 2,
51 	.clock = V_NS16550_CLK,
52 	.fcr = UART_FCR_DEFVAL,
53 };
54 
55 U_BOOT_DEVICE(devkit8000_uart) = {
56 	"ns16550_serial",
57 	&devkit8000_serial
58 };
59 
60 /*
61  * Routine: board_init
62  * Description: Early hardware init.
63  */
64 int board_init(void)
65 {
66 	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
67 	/* board id for Linux */
68 	gd->bd->bi_arch_number = MACH_TYPE_DEVKIT8000;
69 	/* boot param addr */
70 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
71 
72 	return 0;
73 }
74 
75 /* Configure GPMC registers for DM9000 */
76 static void gpmc_dm9000_config(void)
77 {
78 	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[6],
79 		CONFIG_DM9000_BASE, GPMC_SIZE_16M);
80 }
81 
82 /*
83  * Routine: misc_init_r
84  * Description: Configure board specific parts
85  */
86 int misc_init_r(void)
87 {
88 	struct ctrl_id *id_base = (struct ctrl_id *)OMAP34XX_ID_L4_IO_BASE;
89 #ifdef CONFIG_DRIVER_DM9000
90 	uchar enetaddr[6];
91 	u32 die_id_0;
92 #endif
93 
94 	twl4030_power_init();
95 #ifdef CONFIG_TWL4030_LED
96 	twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
97 #endif
98 
99 #ifdef CONFIG_DRIVER_DM9000
100 	/* Configure GPMC registers for DM9000 */
101 	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[6],
102 			CONFIG_DM9000_BASE, GPMC_SIZE_16M);
103 
104 	/* Use OMAP DIE_ID as MAC address */
105 	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
106 		printf("ethaddr not set, using Die ID\n");
107 		die_id_0 = readl(&id_base->die_id_0);
108 		enetaddr[0] = 0x02; /* locally administered */
109 		enetaddr[1] = readl(&id_base->die_id_1) & 0xff;
110 		enetaddr[2] = (die_id_0 & 0xff000000) >> 24;
111 		enetaddr[3] = (die_id_0 & 0x00ff0000) >> 16;
112 		enetaddr[4] = (die_id_0 & 0x0000ff00) >> 8;
113 		enetaddr[5] = (die_id_0 & 0x000000ff);
114 		eth_setenv_enetaddr("ethaddr", enetaddr);
115 	}
116 #endif
117 
118 	omap_die_id_display();
119 
120 	return 0;
121 }
122 
123 /*
124  * Routine: set_muxconf_regs
125  * Description: Setting up the configuration Mux registers specific to the
126  *		hardware. Many pins need to be moved from protect to primary
127  *		mode.
128  */
129 void set_muxconf_regs(void)
130 {
131 	MUX_DEVKIT8000();
132 }
133 
134 #if defined(CONFIG_MMC)
135 int board_mmc_init(bd_t *bis)
136 {
137 	return omap_mmc_init(0, 0, 0, -1, -1);
138 }
139 #endif
140 
141 #if defined(CONFIG_MMC)
142 void board_mmc_power_init(void)
143 {
144 	twl4030_power_mmc_init(0);
145 }
146 #endif
147 
148 #if defined(CONFIG_DRIVER_DM9000) & !defined(CONFIG_SPL_BUILD)
149 /*
150  * Routine: board_eth_init
151  * Description: Setting up the Ethernet hardware.
152  */
153 int board_eth_init(bd_t *bis)
154 {
155 	return dm9000_initialize(bis);
156 }
157 #endif
158 
159 #ifdef CONFIG_SPL_OS_BOOT
160 /*
161  * Do board specific preparation before SPL
162  * Linux boot
163  */
164 void spl_board_prepare_for_linux(void)
165 {
166 	gpmc_dm9000_config();
167 }
168 
169 /*
170  * devkit8000 specific implementation of spl_start_uboot()
171  *
172  * RETURN
173  * 0 if the button is not pressed
174  * 1 if the button is pressed
175  */
176 int spl_start_uboot(void)
177 {
178 	int val = 0;
179 	if (!gpio_request(SPL_OS_BOOT_KEY, "U-Boot key")) {
180 		gpio_direction_input(SPL_OS_BOOT_KEY);
181 		val = gpio_get_value(SPL_OS_BOOT_KEY);
182 		gpio_free(SPL_OS_BOOT_KEY);
183 	}
184 	return !val;
185 }
186 #endif
187 
188 /*
189  * Routine: get_board_mem_timings
190  * Description: If we use SPL then there is no x-loader nor config header
191  * so we have to setup the DDR timings ourself on the first bank.  This
192  * provides the timing values back to the function that configures
193  * the memory.  We have either one or two banks of 128MB DDR.
194  */
195 void get_board_mem_timings(struct board_sdrc_timings *timings)
196 {
197 	/* General SDRC config */
198 	timings->mcfg = MICRON_V_MCFG_165(128 << 20);
199 	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
200 
201 	/* AC timings */
202 	timings->ctrla = MICRON_V_ACTIMA_165;
203 	timings->ctrlb = MICRON_V_ACTIMB_165;
204 
205 	timings->mr = MICRON_V_MR_165;
206 }
207