1 /*
2  * (C) Copyright 2004-2008
3  * Texas Instruments, <www.ti.com>
4  *
5  * Author :
6  *	Sunil Kumar <sunilsaini05@gmail.com>
7  *	Shashi Ranjan <shashiranjanmca05@gmail.com>
8  *
9  * (C) Copyright 2009
10  * Frederik Kriewitz <frederik@kriewitz.eu>
11  *
12  * Derived from Beagle Board and 3430 SDP code by
13  *	Richard Woodruff <r-woodruff2@ti.com>
14  *	Syed Mohammed Khasim <khasim@ti.com>
15  *
16  *
17  * SPDX-License-Identifier:	GPL-2.0+
18  */
19 #include <common.h>
20 #include <dm.h>
21 #include <ns16550.h>
22 #include <twl4030.h>
23 #include <asm/io.h>
24 #include <asm/arch/mmc_host_def.h>
25 #include <asm/arch/mux.h>
26 #include <asm/arch/sys_proto.h>
27 #include <asm/arch/mem.h>
28 #include <asm/mach-types.h>
29 #include "devkit8000.h"
30 #include <asm/gpio.h>
31 #ifdef CONFIG_DRIVER_DM9000
32 #include <net.h>
33 #include <netdev.h>
34 #endif
35 
36 DECLARE_GLOBAL_DATA_PTR;
37 
38 static u32 gpmc_net_config[GPMC_MAX_REG] = {
39 	NET_GPMC_CONFIG1,
40 	NET_GPMC_CONFIG2,
41 	NET_GPMC_CONFIG3,
42 	NET_GPMC_CONFIG4,
43 	NET_GPMC_CONFIG5,
44 	NET_GPMC_CONFIG6,
45 	0
46 };
47 
48 static const struct ns16550_platdata devkit8000_serial = {
49 	OMAP34XX_UART3,
50 	2,
51 	V_NS16550_CLK
52 };
53 
54 U_BOOT_DEVICE(devkit8000_uart) = {
55 	"ns16550_serial",
56 	&devkit8000_serial
57 };
58 
59 /*
60  * Routine: board_init
61  * Description: Early hardware init.
62  */
63 int board_init(void)
64 {
65 	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
66 	/* board id for Linux */
67 	gd->bd->bi_arch_number = MACH_TYPE_DEVKIT8000;
68 	/* boot param addr */
69 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
70 
71 	return 0;
72 }
73 
74 /* Configure GPMC registers for DM9000 */
75 static void gpmc_dm9000_config(void)
76 {
77 	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[6],
78 		CONFIG_DM9000_BASE, GPMC_SIZE_16M);
79 }
80 
81 /*
82  * Routine: misc_init_r
83  * Description: Configure board specific parts
84  */
85 int misc_init_r(void)
86 {
87 	struct ctrl_id *id_base = (struct ctrl_id *)OMAP34XX_ID_L4_IO_BASE;
88 #ifdef CONFIG_DRIVER_DM9000
89 	uchar enetaddr[6];
90 	u32 die_id_0;
91 #endif
92 
93 	twl4030_power_init();
94 #ifdef CONFIG_TWL4030_LED
95 	twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
96 #endif
97 
98 #ifdef CONFIG_DRIVER_DM9000
99 	/* Configure GPMC registers for DM9000 */
100 	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[6],
101 			CONFIG_DM9000_BASE, GPMC_SIZE_16M);
102 
103 	/* Use OMAP DIE_ID as MAC address */
104 	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
105 		printf("ethaddr not set, using Die ID\n");
106 		die_id_0 = readl(&id_base->die_id_0);
107 		enetaddr[0] = 0x02; /* locally administered */
108 		enetaddr[1] = readl(&id_base->die_id_1) & 0xff;
109 		enetaddr[2] = (die_id_0 & 0xff000000) >> 24;
110 		enetaddr[3] = (die_id_0 & 0x00ff0000) >> 16;
111 		enetaddr[4] = (die_id_0 & 0x0000ff00) >> 8;
112 		enetaddr[5] = (die_id_0 & 0x000000ff);
113 		eth_setenv_enetaddr("ethaddr", enetaddr);
114 	}
115 #endif
116 
117 	omap_die_id_display();
118 
119 	return 0;
120 }
121 
122 /*
123  * Routine: set_muxconf_regs
124  * Description: Setting up the configuration Mux registers specific to the
125  *		hardware. Many pins need to be moved from protect to primary
126  *		mode.
127  */
128 void set_muxconf_regs(void)
129 {
130 	MUX_DEVKIT8000();
131 }
132 
133 #if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
134 int board_mmc_init(bd_t *bis)
135 {
136 	return omap_mmc_init(0, 0, 0, -1, -1);
137 }
138 #endif
139 
140 #if defined(CONFIG_GENERIC_MMC)
141 void board_mmc_power_init(void)
142 {
143 	twl4030_power_mmc_init(0);
144 }
145 #endif
146 
147 #if defined(CONFIG_DRIVER_DM9000) & !defined(CONFIG_SPL_BUILD)
148 /*
149  * Routine: board_eth_init
150  * Description: Setting up the Ethernet hardware.
151  */
152 int board_eth_init(bd_t *bis)
153 {
154 	return dm9000_initialize(bis);
155 }
156 #endif
157 
158 #ifdef CONFIG_SPL_OS_BOOT
159 /*
160  * Do board specific preperation before SPL
161  * Linux boot
162  */
163 void spl_board_prepare_for_linux(void)
164 {
165 	gpmc_dm9000_config();
166 }
167 
168 /*
169  * devkit8000 specific implementation of spl_start_uboot()
170  *
171  * RETURN
172  * 0 if the button is not pressed
173  * 1 if the button is pressed
174  */
175 int spl_start_uboot(void)
176 {
177 	int val = 0;
178 	if (!gpio_request(SPL_OS_BOOT_KEY, "U-Boot key")) {
179 		gpio_direction_input(SPL_OS_BOOT_KEY);
180 		val = gpio_get_value(SPL_OS_BOOT_KEY);
181 		gpio_free(SPL_OS_BOOT_KEY);
182 	}
183 	return !val;
184 }
185 #endif
186 
187 /*
188  * Routine: get_board_mem_timings
189  * Description: If we use SPL then there is no x-loader nor config header
190  * so we have to setup the DDR timings ourself on the first bank.  This
191  * provides the timing values back to the function that configures
192  * the memory.  We have either one or two banks of 128MB DDR.
193  */
194 void get_board_mem_timings(struct board_sdrc_timings *timings)
195 {
196 	/* General SDRC config */
197 	timings->mcfg = MICRON_V_MCFG_165(128 << 20);
198 	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
199 
200 	/* AC timings */
201 	timings->ctrla = MICRON_V_ACTIMA_165;
202 	timings->ctrlb = MICRON_V_ACTIMB_165;
203 
204 	timings->mr = MICRON_V_MR_165;
205 }
206