1 /* 2 * (C) Copyright 2010 3 * Texas Instruments Incorporated, <www.ti.com> 4 * Aneesh V <aneesh@ti.com> 5 * Steve Sakoman <steve@sakoman.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 #include <common.h> 10 #include <palmas.h> 11 #include <asm/arch/sys_proto.h> 12 #include <asm/arch/mmc_host_def.h> 13 #include <tca642x.h> 14 15 #include "mux_data.h" 16 17 #if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP) 18 #include <sata.h> 19 #include <usb.h> 20 #include <asm/gpio.h> 21 #include <asm/arch/clock.h> 22 #include <asm/arch/ehci.h> 23 #include <asm/ehci-omap.h> 24 #include <asm/arch/sata.h> 25 26 #define DIE_ID_REG_BASE (OMAP54XX_L4_CORE_BASE + 0x2000) 27 #define DIE_ID_REG_OFFSET 0x200 28 29 #endif 30 31 DECLARE_GLOBAL_DATA_PTR; 32 33 const struct omap_sysinfo sysinfo = { 34 "Board: OMAP5432 uEVM\n" 35 }; 36 37 /** 38 * @brief tca642x_init - uEVM default values for the GPIO expander 39 * input reg, output reg, polarity reg, configuration reg 40 */ 41 struct tca642x_bank_info tca642x_init[] = { 42 { .input_reg = 0x00, 43 .output_reg = 0x04, 44 .polarity_reg = 0x00, 45 .configuration_reg = 0x80 }, 46 { .input_reg = 0x00, 47 .output_reg = 0x00, 48 .polarity_reg = 0x00, 49 .configuration_reg = 0xff }, 50 { .input_reg = 0x00, 51 .output_reg = 0x00, 52 .polarity_reg = 0x00, 53 .configuration_reg = 0x40 }, 54 }; 55 56 /** 57 * @brief board_init 58 * 59 * @return 0 60 */ 61 int board_init(void) 62 { 63 gpmc_init(); 64 gd->bd->bi_arch_number = MACH_TYPE_OMAP5_SEVM; 65 gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */ 66 67 tca642x_set_inital_state(CONFIG_SYS_I2C_TCA642X_ADDR, tca642x_init); 68 69 return 0; 70 } 71 72 int board_late_init(void) 73 { 74 init_sata(0); 75 return 0; 76 } 77 78 int board_eth_init(bd_t *bis) 79 { 80 return 0; 81 } 82 83 #if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP) 84 static void enable_host_clocks(void) 85 { 86 int auxclk; 87 int hs_clk_ctrl_val = (OPTFCLKEN_HSIC60M_P3_CLK | 88 OPTFCLKEN_HSIC480M_P3_CLK | 89 OPTFCLKEN_HSIC60M_P2_CLK | 90 OPTFCLKEN_HSIC480M_P2_CLK | 91 OPTFCLKEN_UTMI_P3_CLK | OPTFCLKEN_UTMI_P2_CLK); 92 93 /* Enable port 2 and 3 clocks*/ 94 setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, hs_clk_ctrl_val); 95 96 /* Enable port 2 and 3 usb host ports tll clocks*/ 97 setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl, 98 (OPTFCLKEN_USB_CH1_CLK_ENABLE | OPTFCLKEN_USB_CH2_CLK_ENABLE)); 99 #ifdef CONFIG_USB_XHCI_OMAP 100 /* Enable the USB OTG Super speed clocks */ 101 setbits_le32((*prcm)->cm_l3init_usb_otg_ss_clkctrl, 102 (OPTFCLKEN_REFCLK960M | OTG_SS_CLKCTRL_MODULEMODE_HW)); 103 #endif 104 105 auxclk = readl((*prcm)->scrm_auxclk1); 106 /* Request auxilary clock */ 107 auxclk |= AUXCLK_ENABLE_MASK; 108 writel(auxclk, (*prcm)->scrm_auxclk1); 109 } 110 #endif 111 112 /** 113 * @brief misc_init_r - Configure EVM board specific configurations 114 * such as power configurations, ethernet initialization as phase2 of 115 * boot sequence 116 * 117 * @return 0 118 */ 119 int misc_init_r(void) 120 { 121 int reg; 122 u32 id[4]; 123 124 #ifdef CONFIG_PALMAS_POWER 125 palmas_init_settings(); 126 #endif 127 128 reg = DIE_ID_REG_BASE + DIE_ID_REG_OFFSET; 129 130 id[0] = readl(reg); 131 id[1] = readl(reg + 0x8); 132 id[2] = readl(reg + 0xC); 133 id[3] = readl(reg + 0x10); 134 usb_fake_mac_from_die_id(id); 135 136 return 0; 137 } 138 139 void set_muxconf_regs_essential(void) 140 { 141 do_set_mux((*ctrl)->control_padconf_core_base, 142 core_padconf_array_essential, 143 sizeof(core_padconf_array_essential) / 144 sizeof(struct pad_conf_entry)); 145 146 do_set_mux((*ctrl)->control_padconf_wkup_base, 147 wkup_padconf_array_essential, 148 sizeof(wkup_padconf_array_essential) / 149 sizeof(struct pad_conf_entry)); 150 } 151 152 #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) 153 int board_mmc_init(bd_t *bis) 154 { 155 omap_mmc_init(0, 0, 0, -1, -1); 156 omap_mmc_init(1, 0, 0, -1, -1); 157 return 0; 158 } 159 #endif 160 161 #ifdef CONFIG_USB_EHCI 162 static struct omap_usbhs_board_data usbhs_bdata = { 163 .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, 164 .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC, 165 .port_mode[2] = OMAP_EHCI_PORT_MODE_HSIC, 166 }; 167 168 int ehci_hcd_init(int index, enum usb_init_type init, 169 struct ehci_hccr **hccr, struct ehci_hcor **hcor) 170 { 171 int ret; 172 173 enable_host_clocks(); 174 175 ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); 176 if (ret < 0) { 177 puts("Failed to initialize ehci\n"); 178 return ret; 179 } 180 181 return 0; 182 } 183 184 int ehci_hcd_stop(void) 185 { 186 int ret; 187 188 ret = omap_ehci_hcd_stop(); 189 return ret; 190 } 191 192 void usb_hub_reset_devices(int port) 193 { 194 /* The LAN9730 needs to be reset after the port power has been set. */ 195 if (port == 3) { 196 gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 0); 197 udelay(10); 198 gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 1); 199 } 200 } 201 #endif 202 203 #ifdef CONFIG_USB_XHCI_OMAP 204 /** 205 * @brief board_usb_init - Configure EVM board specific configurations 206 * for the LDO's and clocks for the USB blocks. 207 * 208 * @return 0 209 */ 210 int board_usb_init(int index, enum usb_init_type init) 211 { 212 int ret; 213 #ifdef CONFIG_PALMAS_USB_SS_PWR 214 ret = palmas_enable_ss_ldo(); 215 #endif 216 217 enable_host_clocks(); 218 219 return 0; 220 } 221 #endif 222