1 /* 2 * (C) Copyright 2013 3 * Texas Instruments Incorporated, <www.ti.com> 4 * 5 * Lokesh Vutla <lokeshvutla@ti.com> 6 * 7 * Based on previous work by: 8 * Aneesh V <aneesh@ti.com> 9 * Steve Sakoman <steve@sakoman.com> 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 #include <common.h> 14 #include <palmas.h> 15 #include <sata.h> 16 #include <asm/gpio.h> 17 #include <asm/arch/gpio.h> 18 #include <asm/arch/sys_proto.h> 19 #include <asm/arch/mmc_host_def.h> 20 #include <asm/arch/sata.h> 21 #include <environment.h> 22 23 #include "mux_data.h" 24 25 #ifdef CONFIG_DRIVER_TI_CPSW 26 #include <cpsw.h> 27 #endif 28 29 DECLARE_GLOBAL_DATA_PTR; 30 31 /* GPIO 7_11 */ 32 #define GPIO_DDR_VTT_EN 203 33 34 const struct omap_sysinfo sysinfo = { 35 "Board: DRA7xx\n" 36 }; 37 38 /* 39 * Adjust I/O delays on the Tx control and data lines of each MAC port. This 40 * is a workaround in order to work properly with the DP83865 PHYs on the EVM. 41 * In 3COM RGMII mode this PHY applies it's own internal clock delay, so we 42 * essentially need to counteract the DRA7xx internal delay, and we do this 43 * by delaying the control and data lines. If not using this PHY, you probably 44 * don't need to do this stuff! 45 */ 46 static void dra7xx_adj_io_delay(const struct io_delay *io_dly) 47 { 48 int i = 0; 49 u32 reg_val; 50 u32 delta; 51 u32 coarse; 52 u32 fine; 53 54 writel(CFG_IO_DELAY_UNLOCK_KEY, CFG_IO_DELAY_LOCK); 55 56 while(io_dly[i].addr) { 57 writel(CFG_IO_DELAY_ACCESS_PATTERN & ~CFG_IO_DELAY_LOCK_MASK, 58 io_dly[i].addr); 59 delta = io_dly[i].dly; 60 reg_val = readl(io_dly[i].addr) & 0x3ff; 61 coarse = ((reg_val >> 5) & 0x1F) + ((delta >> 5) & 0x1F); 62 coarse = (coarse > 0x1F) ? (0x1F) : (coarse); 63 fine = (reg_val & 0x1F) + (delta & 0x1F); 64 fine = (fine > 0x1F) ? (0x1F) : (fine); 65 reg_val = CFG_IO_DELAY_ACCESS_PATTERN | 66 CFG_IO_DELAY_LOCK_MASK | 67 ((coarse << 5) | (fine)); 68 writel(reg_val, io_dly[i].addr); 69 i++; 70 } 71 72 writel(CFG_IO_DELAY_LOCK_KEY, CFG_IO_DELAY_LOCK); 73 } 74 75 /** 76 * @brief board_init 77 * 78 * @return 0 79 */ 80 int board_init(void) 81 { 82 gpmc_init(); 83 gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */ 84 85 return 0; 86 } 87 88 int board_late_init(void) 89 { 90 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 91 if (omap_revision() == DRA722_ES1_0) 92 setenv("board_name", "dra72x"); 93 else 94 setenv("board_name", "dra7xx"); 95 #endif 96 init_sata(0); 97 return 0; 98 } 99 100 /** 101 * @brief misc_init_r - Configure EVM board specific configurations 102 * such as power configurations, ethernet initialization as phase2 of 103 * boot sequence 104 * 105 * @return 0 106 */ 107 int misc_init_r(void) 108 { 109 return 0; 110 } 111 112 static void do_set_mux32(u32 base, 113 struct pad_conf_entry const *array, int size) 114 { 115 int i; 116 struct pad_conf_entry *pad = (struct pad_conf_entry *)array; 117 118 for (i = 0; i < size; i++, pad++) 119 writel(pad->val, base + pad->offset); 120 } 121 122 void set_muxconf_regs_essential(void) 123 { 124 do_set_mux32((*ctrl)->control_padconf_core_base, 125 core_padconf_array_essential, 126 sizeof(core_padconf_array_essential) / 127 sizeof(struct pad_conf_entry)); 128 } 129 130 #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) 131 int board_mmc_init(bd_t *bis) 132 { 133 omap_mmc_init(0, 0, 0, -1, -1); 134 omap_mmc_init(1, 0, 0, -1, -1); 135 return 0; 136 } 137 #endif 138 139 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT) 140 int spl_start_uboot(void) 141 { 142 /* break into full u-boot on 'c' */ 143 if (serial_tstc() && serial_getc() == 'c') 144 return 1; 145 146 #ifdef CONFIG_SPL_ENV_SUPPORT 147 env_init(); 148 env_relocate_spec(); 149 if (getenv_yesno("boot_os") != 1) 150 return 1; 151 #endif 152 153 return 0; 154 } 155 #endif 156 157 #ifdef CONFIG_DRIVER_TI_CPSW 158 159 /* Delay value to add to calibrated value */ 160 #define RGMII0_TXCTL_DLY_VAL ((0x3 << 5) + 0x8) 161 #define RGMII0_TXD0_DLY_VAL ((0x3 << 5) + 0x8) 162 #define RGMII0_TXD1_DLY_VAL ((0x3 << 5) + 0x2) 163 #define RGMII0_TXD2_DLY_VAL ((0x4 << 5) + 0x0) 164 #define RGMII0_TXD3_DLY_VAL ((0x4 << 5) + 0x0) 165 #define VIN2A_D13_DLY_VAL ((0x3 << 5) + 0x8) 166 #define VIN2A_D17_DLY_VAL ((0x3 << 5) + 0x8) 167 #define VIN2A_D16_DLY_VAL ((0x3 << 5) + 0x2) 168 #define VIN2A_D15_DLY_VAL ((0x4 << 5) + 0x0) 169 #define VIN2A_D14_DLY_VAL ((0x4 << 5) + 0x0) 170 171 extern u32 *const omap_si_rev; 172 173 static void cpsw_control(int enabled) 174 { 175 /* VTP can be added here */ 176 177 return; 178 } 179 180 static struct cpsw_slave_data cpsw_slaves[] = { 181 { 182 .slave_reg_ofs = 0x208, 183 .sliver_reg_ofs = 0xd80, 184 .phy_addr = 2, 185 }, 186 { 187 .slave_reg_ofs = 0x308, 188 .sliver_reg_ofs = 0xdc0, 189 .phy_addr = 3, 190 }, 191 }; 192 193 static struct cpsw_platform_data cpsw_data = { 194 .mdio_base = CPSW_MDIO_BASE, 195 .cpsw_base = CPSW_BASE, 196 .mdio_div = 0xff, 197 .channels = 8, 198 .cpdma_reg_ofs = 0x800, 199 .slaves = 2, 200 .slave_data = cpsw_slaves, 201 .ale_reg_ofs = 0xd00, 202 .ale_entries = 1024, 203 .host_port_reg_ofs = 0x108, 204 .hw_stats_reg_ofs = 0x900, 205 .bd_ram_ofs = 0x2000, 206 .mac_control = (1 << 5), 207 .control = cpsw_control, 208 .host_port_num = 0, 209 .version = CPSW_CTRL_VERSION_2, 210 }; 211 212 int board_eth_init(bd_t *bis) 213 { 214 int ret; 215 uint8_t mac_addr[6]; 216 uint32_t mac_hi, mac_lo; 217 uint32_t ctrl_val; 218 const struct io_delay io_dly[] = { 219 {CFG_RGMII0_TXCTL, RGMII0_TXCTL_DLY_VAL}, 220 {CFG_RGMII0_TXD0, RGMII0_TXD0_DLY_VAL}, 221 {CFG_RGMII0_TXD1, RGMII0_TXD1_DLY_VAL}, 222 {CFG_RGMII0_TXD2, RGMII0_TXD2_DLY_VAL}, 223 {CFG_RGMII0_TXD3, RGMII0_TXD3_DLY_VAL}, 224 {CFG_VIN2A_D13, VIN2A_D13_DLY_VAL}, 225 {CFG_VIN2A_D17, VIN2A_D17_DLY_VAL}, 226 {CFG_VIN2A_D16, VIN2A_D16_DLY_VAL}, 227 {CFG_VIN2A_D15, VIN2A_D15_DLY_VAL}, 228 {CFG_VIN2A_D14, VIN2A_D14_DLY_VAL}, 229 {0} 230 }; 231 232 /* Adjust IO delay for RGMII tx path */ 233 dra7xx_adj_io_delay(io_dly); 234 235 /* try reading mac address from efuse */ 236 mac_lo = readl((*ctrl)->control_core_mac_id_0_lo); 237 mac_hi = readl((*ctrl)->control_core_mac_id_0_hi); 238 mac_addr[0] = (mac_hi & 0xFF0000) >> 16; 239 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 240 mac_addr[2] = mac_hi & 0xFF; 241 mac_addr[3] = (mac_lo & 0xFF0000) >> 16; 242 mac_addr[4] = (mac_lo & 0xFF00) >> 8; 243 mac_addr[5] = mac_lo & 0xFF; 244 245 if (!getenv("ethaddr")) { 246 printf("<ethaddr> not set. Validating first E-fuse MAC\n"); 247 248 if (is_valid_ether_addr(mac_addr)) 249 eth_setenv_enetaddr("ethaddr", mac_addr); 250 } 251 252 mac_lo = readl((*ctrl)->control_core_mac_id_1_lo); 253 mac_hi = readl((*ctrl)->control_core_mac_id_1_hi); 254 mac_addr[0] = (mac_hi & 0xFF0000) >> 16; 255 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 256 mac_addr[2] = mac_hi & 0xFF; 257 mac_addr[3] = (mac_lo & 0xFF0000) >> 16; 258 mac_addr[4] = (mac_lo & 0xFF00) >> 8; 259 mac_addr[5] = mac_lo & 0xFF; 260 261 if (!getenv("eth1addr")) { 262 if (is_valid_ether_addr(mac_addr)) 263 eth_setenv_enetaddr("eth1addr", mac_addr); 264 } 265 266 ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33); 267 ctrl_val |= 0x22; 268 writel(ctrl_val, (*ctrl)->control_core_control_io1); 269 270 if (*omap_si_rev == DRA722_ES1_0) 271 cpsw_data.active_slave = 1; 272 273 ret = cpsw_register(&cpsw_data); 274 if (ret < 0) 275 printf("Error %d registering CPSW switch\n", ret); 276 277 return ret; 278 } 279 #endif 280 281 #ifdef CONFIG_BOARD_EARLY_INIT_F 282 /* VTT regulator enable */ 283 static inline void vtt_regulator_enable(void) 284 { 285 if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL) 286 return; 287 288 /* Do not enable VTT for DRA722 */ 289 if (omap_revision() == DRA722_ES1_0) 290 return; 291 292 /* 293 * EVM Rev G and later use gpio7_11 for DDR3 termination. 294 * This is safe enough to do on older revs. 295 */ 296 gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); 297 gpio_direction_output(GPIO_DDR_VTT_EN, 1); 298 } 299 300 int board_early_init_f(void) 301 { 302 vtt_regulator_enable(); 303 return 0; 304 } 305 #endif 306