1 /* 2 * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com 3 * 4 * Author: Felipe Balbi <balbi@ti.com> 5 * 6 * Based on board/ti/dra7xx/evm.c 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <palmas.h> 13 #include <sata.h> 14 #include <usb.h> 15 #include <asm/omap_common.h> 16 #include <asm/omap_sec_common.h> 17 #include <asm/emif.h> 18 #include <asm/gpio.h> 19 #include <asm/arch/gpio.h> 20 #include <asm/arch/clock.h> 21 #include <asm/arch/dra7xx_iodelay.h> 22 #include <asm/arch/sys_proto.h> 23 #include <asm/arch/mmc_host_def.h> 24 #include <asm/arch/sata.h> 25 #include <asm/arch/gpio.h> 26 #include <asm/arch/omap.h> 27 #include <environment.h> 28 #include <usb.h> 29 #include <linux/usb/gadget.h> 30 #include <dwc3-uboot.h> 31 #include <dwc3-omap-uboot.h> 32 #include <ti-usb-phy-uboot.h> 33 34 #include "../common/board_detect.h" 35 #include "mux_data.h" 36 37 #define board_is_x15() board_ti_is("BBRDX15_") 38 #define board_is_x15_revb1() (board_ti_is("BBRDX15_") && \ 39 !strncmp("B.10", board_ti_get_rev(), 3)) 40 #define board_is_x15_revc() (board_ti_is("BBRDX15_") && \ 41 !strncmp("C.00", board_ti_get_rev(), 3)) 42 #define board_is_am572x_evm() board_ti_is("AM572PM_") 43 #define board_is_am572x_evm_reva3() \ 44 (board_ti_is("AM572PM_") && \ 45 !strncmp("A.30", board_ti_get_rev(), 3)) 46 #define board_is_am574x_idk() board_ti_is("AM574IDK") 47 #define board_is_am572x_idk() board_ti_is("AM572IDK") 48 #define board_is_am571x_idk() board_ti_is("AM571IDK") 49 50 #ifdef CONFIG_DRIVER_TI_CPSW 51 #include <cpsw.h> 52 #endif 53 54 DECLARE_GLOBAL_DATA_PTR; 55 56 #define GPIO_ETH_LCD GPIO_TO_PIN(2, 22) 57 /* GPIO 7_11 */ 58 #define GPIO_DDR_VTT_EN 203 59 60 /* Touch screen controller to identify the LCD */ 61 #define OSD_TS_FT_BUS_ADDRESS 0 62 #define OSD_TS_FT_CHIP_ADDRESS 0x38 63 #define OSD_TS_FT_REG_ID 0xA3 64 /* 65 * Touchscreen IDs for various OSD panels 66 * Ref: http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf 67 */ 68 /* Used on newer osd101t2587 Panels */ 69 #define OSD_TS_FT_ID_5x46 0x54 70 /* Used on older osd101t2045 Panels */ 71 #define OSD_TS_FT_ID_5606 0x08 72 73 #define SYSINFO_BOARD_NAME_MAX_LEN 45 74 75 #define TPS65903X_PRIMARY_SECONDARY_PAD2 0xFB 76 #define TPS65903X_PAD2_POWERHOLD_MASK 0x20 77 78 const struct omap_sysinfo sysinfo = { 79 "Board: UNKNOWN(BeagleBoard X15?) REV UNKNOWN\n" 80 }; 81 82 static const struct dmm_lisa_map_regs beagle_x15_lisa_regs = { 83 .dmm_lisa_map_3 = 0x80740300, 84 .is_ma_present = 0x1 85 }; 86 87 static const struct dmm_lisa_map_regs am571x_idk_lisa_regs = { 88 .dmm_lisa_map_3 = 0x80640100, 89 .is_ma_present = 0x1 90 }; 91 92 static const struct dmm_lisa_map_regs am574x_idk_lisa_regs = { 93 .dmm_lisa_map_2 = 0xc0600200, 94 .dmm_lisa_map_3 = 0x80600100, 95 .is_ma_present = 0x1 96 }; 97 98 void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs) 99 { 100 if (board_is_am571x_idk()) 101 *dmm_lisa_regs = &am571x_idk_lisa_regs; 102 else if (board_is_am574x_idk()) 103 *dmm_lisa_regs = &am574x_idk_lisa_regs; 104 else 105 *dmm_lisa_regs = &beagle_x15_lisa_regs; 106 } 107 108 static const struct emif_regs beagle_x15_emif1_ddr3_532mhz_emif_regs = { 109 .sdram_config_init = 0x61851b32, 110 .sdram_config = 0x61851b32, 111 .sdram_config2 = 0x08000000, 112 .ref_ctrl = 0x000040F1, 113 .ref_ctrl_final = 0x00001035, 114 .sdram_tim1 = 0xcccf36ab, 115 .sdram_tim2 = 0x308f7fda, 116 .sdram_tim3 = 0x409f88a8, 117 .read_idle_ctrl = 0x00050000, 118 .zq_config = 0x5007190b, 119 .temp_alert_config = 0x00000000, 120 .emif_ddr_phy_ctlr_1_init = 0x0024400b, 121 .emif_ddr_phy_ctlr_1 = 0x0e24400b, 122 .emif_ddr_ext_phy_ctrl_1 = 0x10040100, 123 .emif_ddr_ext_phy_ctrl_2 = 0x00910091, 124 .emif_ddr_ext_phy_ctrl_3 = 0x00950095, 125 .emif_ddr_ext_phy_ctrl_4 = 0x009b009b, 126 .emif_ddr_ext_phy_ctrl_5 = 0x009e009e, 127 .emif_rd_wr_lvl_rmp_win = 0x00000000, 128 .emif_rd_wr_lvl_rmp_ctl = 0x80000000, 129 .emif_rd_wr_lvl_ctl = 0x00000000, 130 .emif_rd_wr_exec_thresh = 0x00000305 131 }; 132 133 /* Ext phy ctrl regs 1-35 */ 134 static const u32 beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs[] = { 135 0x10040100, 136 0x00910091, 137 0x00950095, 138 0x009B009B, 139 0x009E009E, 140 0x00980098, 141 0x00340034, 142 0x00350035, 143 0x00340034, 144 0x00310031, 145 0x00340034, 146 0x007F007F, 147 0x007F007F, 148 0x007F007F, 149 0x007F007F, 150 0x007F007F, 151 0x00480048, 152 0x004A004A, 153 0x00520052, 154 0x00550055, 155 0x00500050, 156 0x00000000, 157 0x00600020, 158 0x40011080, 159 0x08102040, 160 0x0, 161 0x0, 162 0x0, 163 0x0, 164 0x0, 165 0x0, 166 0x0, 167 0x0, 168 0x0, 169 0x0 170 }; 171 172 static const struct emif_regs beagle_x15_emif2_ddr3_532mhz_emif_regs = { 173 .sdram_config_init = 0x61851b32, 174 .sdram_config = 0x61851b32, 175 .sdram_config2 = 0x08000000, 176 .ref_ctrl = 0x000040F1, 177 .ref_ctrl_final = 0x00001035, 178 .sdram_tim1 = 0xcccf36b3, 179 .sdram_tim2 = 0x308f7fda, 180 .sdram_tim3 = 0x407f88a8, 181 .read_idle_ctrl = 0x00050000, 182 .zq_config = 0x5007190b, 183 .temp_alert_config = 0x00000000, 184 .emif_ddr_phy_ctlr_1_init = 0x0024400b, 185 .emif_ddr_phy_ctlr_1 = 0x0e24400b, 186 .emif_ddr_ext_phy_ctrl_1 = 0x10040100, 187 .emif_ddr_ext_phy_ctrl_2 = 0x00910091, 188 .emif_ddr_ext_phy_ctrl_3 = 0x00950095, 189 .emif_ddr_ext_phy_ctrl_4 = 0x009b009b, 190 .emif_ddr_ext_phy_ctrl_5 = 0x009e009e, 191 .emif_rd_wr_lvl_rmp_win = 0x00000000, 192 .emif_rd_wr_lvl_rmp_ctl = 0x80000000, 193 .emif_rd_wr_lvl_ctl = 0x00000000, 194 .emif_rd_wr_exec_thresh = 0x00000305 195 }; 196 197 static const u32 beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs[] = { 198 0x10040100, 199 0x00910091, 200 0x00950095, 201 0x009B009B, 202 0x009E009E, 203 0x00980098, 204 0x00340034, 205 0x00350035, 206 0x00340034, 207 0x00310031, 208 0x00340034, 209 0x007F007F, 210 0x007F007F, 211 0x007F007F, 212 0x007F007F, 213 0x007F007F, 214 0x00480048, 215 0x004A004A, 216 0x00520052, 217 0x00550055, 218 0x00500050, 219 0x00000000, 220 0x00600020, 221 0x40011080, 222 0x08102040, 223 0x0, 224 0x0, 225 0x0, 226 0x0, 227 0x0, 228 0x0, 229 0x0, 230 0x0, 231 0x0, 232 0x0 233 }; 234 235 static const struct emif_regs am571x_emif1_ddr3_666mhz_emif_regs = { 236 .sdram_config_init = 0x61863332, 237 .sdram_config = 0x61863332, 238 .sdram_config2 = 0x08000000, 239 .ref_ctrl = 0x0000514d, 240 .ref_ctrl_final = 0x0000144a, 241 .sdram_tim1 = 0xd333887c, 242 .sdram_tim2 = 0x30b37fe3, 243 .sdram_tim3 = 0x409f8ad8, 244 .read_idle_ctrl = 0x00050000, 245 .zq_config = 0x5007190b, 246 .temp_alert_config = 0x00000000, 247 .emif_ddr_phy_ctlr_1_init = 0x0024400f, 248 .emif_ddr_phy_ctlr_1 = 0x0e24400f, 249 .emif_ddr_ext_phy_ctrl_1 = 0x10040100, 250 .emif_ddr_ext_phy_ctrl_2 = 0x00910091, 251 .emif_ddr_ext_phy_ctrl_3 = 0x00950095, 252 .emif_ddr_ext_phy_ctrl_4 = 0x009b009b, 253 .emif_ddr_ext_phy_ctrl_5 = 0x009e009e, 254 .emif_rd_wr_lvl_rmp_win = 0x00000000, 255 .emif_rd_wr_lvl_rmp_ctl = 0x80000000, 256 .emif_rd_wr_lvl_ctl = 0x00000000, 257 .emif_rd_wr_exec_thresh = 0x00000305 258 }; 259 260 static const struct emif_regs am574x_emif1_ddr3_666mhz_emif_ecc_regs = { 261 .sdram_config_init = 0x61863332, 262 .sdram_config = 0x61863332, 263 .sdram_config2 = 0x08000000, 264 .ref_ctrl = 0x0000514d, 265 .ref_ctrl_final = 0x0000144a, 266 .sdram_tim1 = 0xd333887c, 267 .sdram_tim2 = 0x30b37fe3, 268 .sdram_tim3 = 0x409f8ad8, 269 .read_idle_ctrl = 0x00050000, 270 .zq_config = 0x5007190b, 271 .temp_alert_config = 0x00000000, 272 .emif_ddr_phy_ctlr_1_init = 0x0024400f, 273 .emif_ddr_phy_ctlr_1 = 0x0e24400f, 274 .emif_ddr_ext_phy_ctrl_1 = 0x10040100, 275 .emif_ddr_ext_phy_ctrl_2 = 0x00910091, 276 .emif_ddr_ext_phy_ctrl_3 = 0x00950095, 277 .emif_ddr_ext_phy_ctrl_4 = 0x009b009b, 278 .emif_ddr_ext_phy_ctrl_5 = 0x009e009e, 279 .emif_rd_wr_lvl_rmp_win = 0x00000000, 280 .emif_rd_wr_lvl_rmp_ctl = 0x80000000, 281 .emif_rd_wr_lvl_ctl = 0x00000000, 282 .emif_rd_wr_exec_thresh = 0x00000305, 283 .emif_ecc_ctrl_reg = 0xD0000001, 284 .emif_ecc_address_range_1 = 0x3FFF0000, 285 .emif_ecc_address_range_2 = 0x00000000 286 }; 287 288 void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs) 289 { 290 switch (emif_nr) { 291 case 1: 292 if (board_is_am571x_idk()) 293 *regs = &am571x_emif1_ddr3_666mhz_emif_regs; 294 else if (board_is_am574x_idk()) 295 *regs = &am574x_emif1_ddr3_666mhz_emif_ecc_regs; 296 else 297 *regs = &beagle_x15_emif1_ddr3_532mhz_emif_regs; 298 break; 299 case 2: 300 if (board_is_am574x_idk()) 301 *regs = &am571x_emif1_ddr3_666mhz_emif_regs; 302 else 303 *regs = &beagle_x15_emif2_ddr3_532mhz_emif_regs; 304 break; 305 } 306 } 307 308 void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size) 309 { 310 switch (emif_nr) { 311 case 1: 312 *regs = beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs; 313 *size = ARRAY_SIZE(beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs); 314 break; 315 case 2: 316 *regs = beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs; 317 *size = ARRAY_SIZE(beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs); 318 break; 319 } 320 } 321 322 struct vcores_data beagle_x15_volts = { 323 .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, 324 .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, 325 .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 326 .mpu.addr = TPS659038_REG_ADDR_SMPS12, 327 .mpu.pmic = &tps659038, 328 .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, 329 330 .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, 331 .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, 332 .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, 333 .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, 334 .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, 335 .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, 336 .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, 337 .eve.addr = TPS659038_REG_ADDR_SMPS45, 338 .eve.pmic = &tps659038, 339 .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, 340 341 .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, 342 .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, 343 .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, 344 .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, 345 .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, 346 .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, 347 .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 348 .gpu.addr = TPS659038_REG_ADDR_SMPS45, 349 .gpu.pmic = &tps659038, 350 .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, 351 352 .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, 353 .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, 354 .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, 355 .core.addr = TPS659038_REG_ADDR_SMPS6, 356 .core.pmic = &tps659038, 357 358 .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, 359 .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, 360 .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, 361 .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, 362 .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, 363 .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, 364 .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, 365 .iva.addr = TPS659038_REG_ADDR_SMPS45, 366 .iva.pmic = &tps659038, 367 .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, 368 }; 369 370 struct vcores_data am572x_idk_volts = { 371 .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, 372 .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, 373 .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 374 .mpu.addr = TPS659038_REG_ADDR_SMPS12, 375 .mpu.pmic = &tps659038, 376 .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, 377 378 .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, 379 .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, 380 .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, 381 .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, 382 .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, 383 .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, 384 .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, 385 .eve.addr = TPS659038_REG_ADDR_SMPS45, 386 .eve.pmic = &tps659038, 387 .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, 388 389 .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, 390 .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, 391 .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, 392 .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, 393 .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, 394 .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, 395 .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 396 .gpu.addr = TPS659038_REG_ADDR_SMPS6, 397 .gpu.pmic = &tps659038, 398 .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, 399 400 .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, 401 .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, 402 .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, 403 .core.addr = TPS659038_REG_ADDR_SMPS7, 404 .core.pmic = &tps659038, 405 406 .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, 407 .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, 408 .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, 409 .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, 410 .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, 411 .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, 412 .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, 413 .iva.addr = TPS659038_REG_ADDR_SMPS8, 414 .iva.pmic = &tps659038, 415 .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, 416 }; 417 418 struct vcores_data am571x_idk_volts = { 419 .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, 420 .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, 421 .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 422 .mpu.addr = TPS659038_REG_ADDR_SMPS12, 423 .mpu.pmic = &tps659038, 424 .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, 425 426 .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, 427 .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, 428 .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, 429 .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, 430 .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, 431 .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, 432 .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, 433 .eve.addr = TPS659038_REG_ADDR_SMPS45, 434 .eve.pmic = &tps659038, 435 .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, 436 437 .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, 438 .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, 439 .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, 440 .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, 441 .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, 442 .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, 443 .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 444 .gpu.addr = TPS659038_REG_ADDR_SMPS6, 445 .gpu.pmic = &tps659038, 446 .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, 447 448 .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, 449 .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, 450 .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, 451 .core.addr = TPS659038_REG_ADDR_SMPS7, 452 .core.pmic = &tps659038, 453 454 .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, 455 .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, 456 .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, 457 .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, 458 .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, 459 .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, 460 .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, 461 .iva.addr = TPS659038_REG_ADDR_SMPS45, 462 .iva.pmic = &tps659038, 463 .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, 464 }; 465 466 int get_voltrail_opp(int rail_offset) 467 { 468 int opp; 469 470 switch (rail_offset) { 471 case VOLT_MPU: 472 opp = DRA7_MPU_OPP; 473 break; 474 case VOLT_CORE: 475 opp = DRA7_CORE_OPP; 476 break; 477 case VOLT_GPU: 478 opp = DRA7_GPU_OPP; 479 break; 480 case VOLT_EVE: 481 opp = DRA7_DSPEVE_OPP; 482 break; 483 case VOLT_IVA: 484 opp = DRA7_IVA_OPP; 485 break; 486 default: 487 opp = OPP_NOM; 488 } 489 490 return opp; 491 } 492 493 494 #ifdef CONFIG_SPL_BUILD 495 /* No env to setup for SPL */ 496 static inline void setup_board_eeprom_env(void) { } 497 498 /* Override function to read eeprom information */ 499 void do_board_detect(void) 500 { 501 int rc; 502 503 rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, 504 CONFIG_EEPROM_CHIP_ADDRESS); 505 if (rc) 506 printf("ti_i2c_eeprom_init failed %d\n", rc); 507 } 508 509 #else /* CONFIG_SPL_BUILD */ 510 511 /* Override function to read eeprom information: actual i2c read done by SPL*/ 512 void do_board_detect(void) 513 { 514 char *bname = NULL; 515 int rc; 516 517 rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, 518 CONFIG_EEPROM_CHIP_ADDRESS); 519 if (rc) 520 printf("ti_i2c_eeprom_init failed %d\n", rc); 521 522 if (board_is_x15()) 523 bname = "BeagleBoard X15"; 524 else if (board_is_am572x_evm()) 525 bname = "AM572x EVM"; 526 else if (board_is_am574x_idk()) 527 bname = "AM574x IDK"; 528 else if (board_is_am572x_idk()) 529 bname = "AM572x IDK"; 530 else if (board_is_am571x_idk()) 531 bname = "AM571x IDK"; 532 533 if (bname) 534 snprintf(sysinfo.board_string, SYSINFO_BOARD_NAME_MAX_LEN, 535 "Board: %s REV %s\n", bname, board_ti_get_rev()); 536 } 537 538 static void setup_board_eeprom_env(void) 539 { 540 char *name = "beagle_x15"; 541 int rc; 542 543 rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, 544 CONFIG_EEPROM_CHIP_ADDRESS); 545 if (rc) 546 goto invalid_eeprom; 547 548 if (board_is_x15()) { 549 if (board_is_x15_revb1()) 550 name = "beagle_x15_revb1"; 551 else if (board_is_x15_revc()) 552 name = "beagle_x15_revc"; 553 else 554 name = "beagle_x15"; 555 } else if (board_is_am572x_evm()) { 556 if (board_is_am572x_evm_reva3()) 557 name = "am57xx_evm_reva3"; 558 else 559 name = "am57xx_evm"; 560 } else if (board_is_am574x_idk()) { 561 name = "am574x_idk"; 562 } else if (board_is_am572x_idk()) { 563 name = "am572x_idk"; 564 } else if (board_is_am571x_idk()) { 565 name = "am571x_idk"; 566 } else { 567 printf("Unidentified board claims %s in eeprom header\n", 568 board_ti_get_name()); 569 } 570 571 invalid_eeprom: 572 set_board_info_env(name); 573 } 574 575 #endif /* CONFIG_SPL_BUILD */ 576 577 void vcores_init(void) 578 { 579 if (board_is_am572x_idk() || board_is_am574x_idk()) 580 *omap_vcores = &am572x_idk_volts; 581 else if (board_is_am571x_idk()) 582 *omap_vcores = &am571x_idk_volts; 583 else 584 *omap_vcores = &beagle_x15_volts; 585 } 586 587 void hw_data_init(void) 588 { 589 *prcm = &dra7xx_prcm; 590 if (is_dra72x()) 591 *dplls_data = &dra72x_dplls; 592 else if (is_dra76x()) 593 *dplls_data = &dra76x_dplls; 594 else 595 *dplls_data = &dra7xx_dplls; 596 *ctrl = &dra7xx_ctrl; 597 } 598 599 bool am571x_idk_needs_lcd(void) 600 { 601 bool needs_lcd; 602 603 gpio_request(GPIO_ETH_LCD, "nLCD_Detect"); 604 if (gpio_get_value(GPIO_ETH_LCD)) 605 needs_lcd = false; 606 else 607 needs_lcd = true; 608 609 gpio_free(GPIO_ETH_LCD); 610 611 return needs_lcd; 612 } 613 614 int board_init(void) 615 { 616 gpmc_init(); 617 gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100); 618 619 return 0; 620 } 621 622 void am57x_idk_lcd_detect(void) 623 { 624 int r = -ENODEV; 625 char *idk_lcd = "no"; 626 uint8_t buf = 0; 627 628 /* Only valid for IDKs */ 629 if (board_is_x15() || board_is_am572x_evm()) 630 return; 631 632 /* Only AM571x IDK has gpio control detect.. so check that */ 633 if (board_is_am571x_idk() && !am571x_idk_needs_lcd()) 634 goto out; 635 636 r = i2c_set_bus_num(OSD_TS_FT_BUS_ADDRESS); 637 if (r) { 638 printf("%s: Failed to set bus address to %d: %d\n", 639 __func__, OSD_TS_FT_BUS_ADDRESS, r); 640 goto out; 641 } 642 r = i2c_probe(OSD_TS_FT_CHIP_ADDRESS); 643 if (r) { 644 /* AM572x IDK has no explicit settings for optional LCD kit */ 645 if (board_is_am571x_idk()) { 646 printf("%s: Touch screen detect failed: %d!\n", 647 __func__, r); 648 } 649 goto out; 650 } 651 652 /* Read FT ID */ 653 r = i2c_read(OSD_TS_FT_CHIP_ADDRESS, OSD_TS_FT_REG_ID, 1, &buf, 1); 654 if (r) { 655 printf("%s: Touch screen ID read %d:0x%02x[0x%02x] failed:%d\n", 656 __func__, OSD_TS_FT_BUS_ADDRESS, OSD_TS_FT_CHIP_ADDRESS, 657 OSD_TS_FT_REG_ID, r); 658 goto out; 659 } 660 661 switch (buf) { 662 case OSD_TS_FT_ID_5606: 663 idk_lcd = "osd101t2045"; 664 break; 665 case OSD_TS_FT_ID_5x46: 666 idk_lcd = "osd101t2587"; 667 break; 668 default: 669 printf("%s: Unidentifed Touch screen ID 0x%02x\n", 670 __func__, buf); 671 /* we will let default be "no lcd" */ 672 } 673 out: 674 env_set("idk_lcd", idk_lcd); 675 return; 676 } 677 678 int board_late_init(void) 679 { 680 setup_board_eeprom_env(); 681 u8 val; 682 683 /* 684 * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds 685 * This is the POWERHOLD-in-Low behavior. 686 */ 687 palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1); 688 689 /* 690 * Default FIT boot on HS devices. Non FIT images are not allowed 691 * on HS devices. 692 */ 693 if (get_device_type() == HS_DEVICE) 694 env_set("boot_fit", "1"); 695 696 /* 697 * Set the GPIO7 Pad to POWERHOLD. This has higher priority 698 * over DEV_CTRL.DEV_ON bit. This can be reset in case of 699 * PMIC Power off. So to be on the safer side set it back 700 * to POWERHOLD mode irrespective of the current state. 701 */ 702 palmas_i2c_read_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2, 703 &val); 704 val = val | TPS65903X_PAD2_POWERHOLD_MASK; 705 palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2, 706 val); 707 708 omap_die_id_serial(); 709 omap_set_fastboot_vars(); 710 711 am57x_idk_lcd_detect(); 712 713 #if !defined(CONFIG_SPL_BUILD) 714 board_ti_set_ethaddr(2); 715 #endif 716 717 return 0; 718 } 719 720 void set_muxconf_regs(void) 721 { 722 do_set_mux32((*ctrl)->control_padconf_core_base, 723 early_padconf, ARRAY_SIZE(early_padconf)); 724 } 725 726 #ifdef CONFIG_IODELAY_RECALIBRATION 727 void recalibrate_iodelay(void) 728 { 729 const struct pad_conf_entry *pconf; 730 const struct iodelay_cfg_entry *iod, *delta_iod; 731 int pconf_sz, iod_sz, delta_iod_sz = 0; 732 int ret; 733 734 if (board_is_am572x_idk()) { 735 pconf = core_padconf_array_essential_am572x_idk; 736 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am572x_idk); 737 iod = iodelay_cfg_array_am572x_idk; 738 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am572x_idk); 739 } else if (board_is_am574x_idk()) { 740 pconf = core_padconf_array_essential_am574x_idk; 741 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am574x_idk); 742 iod = iodelay_cfg_array_am574x_idk; 743 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am574x_idk); 744 } else if (board_is_am571x_idk()) { 745 pconf = core_padconf_array_essential_am571x_idk; 746 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am571x_idk); 747 iod = iodelay_cfg_array_am571x_idk; 748 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk); 749 } else { 750 /* Common for X15/GPEVM */ 751 pconf = core_padconf_array_essential_x15; 752 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_x15); 753 /* There never was an SR1.0 X15.. So.. */ 754 if (omap_revision() == DRA752_ES1_1) { 755 iod = iodelay_cfg_array_x15_sr1_1; 756 iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr1_1); 757 } else { 758 /* Since full production should switch to SR2.0 */ 759 iod = iodelay_cfg_array_x15_sr2_0; 760 iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr2_0); 761 } 762 } 763 764 /* Setup I/O isolation */ 765 ret = __recalibrate_iodelay_start(); 766 if (ret) 767 goto err; 768 769 /* Do the muxing here */ 770 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz); 771 772 /* Now do the weird minor deltas that should be safe */ 773 if (board_is_x15() || board_is_am572x_evm()) { 774 if (board_is_x15_revb1() || board_is_am572x_evm_reva3() || 775 board_is_x15_revc()) { 776 pconf = core_padconf_array_delta_x15_sr2_0; 777 pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr2_0); 778 } else { 779 pconf = core_padconf_array_delta_x15_sr1_1; 780 pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr1_1); 781 } 782 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz); 783 } 784 785 if (board_is_am571x_idk()) { 786 if (am571x_idk_needs_lcd()) { 787 pconf = core_padconf_array_vout_am571x_idk; 788 pconf_sz = ARRAY_SIZE(core_padconf_array_vout_am571x_idk); 789 delta_iod = iodelay_cfg_array_am571x_idk_4port; 790 delta_iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk_4port); 791 792 } else { 793 pconf = core_padconf_array_icss1eth_am571x_idk; 794 pconf_sz = ARRAY_SIZE(core_padconf_array_icss1eth_am571x_idk); 795 } 796 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz); 797 } 798 799 /* Setup IOdelay configuration */ 800 ret = do_set_iodelay((*ctrl)->iodelay_config_base, iod, iod_sz); 801 if (delta_iod_sz) 802 ret = do_set_iodelay((*ctrl)->iodelay_config_base, delta_iod, 803 delta_iod_sz); 804 805 err: 806 /* Closeup.. remove isolation */ 807 __recalibrate_iodelay_end(ret); 808 } 809 #endif 810 811 #if defined(CONFIG_MMC) 812 int board_mmc_init(bd_t *bis) 813 { 814 omap_mmc_init(0, 0, 0, -1, -1); 815 omap_mmc_init(1, 0, 0, -1, -1); 816 return 0; 817 } 818 #endif 819 820 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT) 821 int spl_start_uboot(void) 822 { 823 /* break into full u-boot on 'c' */ 824 if (serial_tstc() && serial_getc() == 'c') 825 return 1; 826 827 #ifdef CONFIG_SPL_ENV_SUPPORT 828 env_init(); 829 env_load(); 830 if (env_get_yesno("boot_os") != 1) 831 return 1; 832 #endif 833 834 return 0; 835 } 836 #endif 837 838 #ifdef CONFIG_USB_DWC3 839 static struct dwc3_device usb_otg_ss2 = { 840 .maximum_speed = USB_SPEED_HIGH, 841 .base = DRA7_USB_OTG_SS2_BASE, 842 .tx_fifo_resize = false, 843 .index = 1, 844 }; 845 846 static struct dwc3_omap_device usb_otg_ss2_glue = { 847 .base = (void *)DRA7_USB_OTG_SS2_GLUE_BASE, 848 .utmi_mode = DWC3_OMAP_UTMI_MODE_SW, 849 .index = 1, 850 }; 851 852 static struct ti_usb_phy_device usb_phy2_device = { 853 .usb2_phy_power = (void *)DRA7_USB2_PHY2_POWER, 854 .index = 1, 855 }; 856 857 int usb_gadget_handle_interrupts(int index) 858 { 859 u32 status; 860 861 status = dwc3_omap_uboot_interrupt_status(index); 862 if (status) 863 dwc3_uboot_handle_interrupt(index); 864 865 return 0; 866 } 867 #endif /* CONFIG_USB_DWC3 */ 868 869 #if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) 870 int omap_xhci_board_usb_init(int index, enum usb_init_type init) 871 { 872 enable_usb_clocks(index); 873 switch (index) { 874 case 0: 875 if (init == USB_INIT_DEVICE) { 876 printf("port %d can't be used as device\n", index); 877 disable_usb_clocks(index); 878 return -EINVAL; 879 } 880 break; 881 case 1: 882 if (init == USB_INIT_DEVICE) { 883 #ifdef CONFIG_USB_DWC3 884 usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL; 885 usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID; 886 ti_usb_phy_uboot_init(&usb_phy2_device); 887 dwc3_omap_uboot_init(&usb_otg_ss2_glue); 888 dwc3_uboot_init(&usb_otg_ss2); 889 #endif 890 } else { 891 printf("port %d can't be used as host\n", index); 892 disable_usb_clocks(index); 893 return -EINVAL; 894 } 895 896 break; 897 default: 898 printf("Invalid Controller Index\n"); 899 } 900 901 return 0; 902 } 903 904 int omap_xhci_board_usb_cleanup(int index, enum usb_init_type init) 905 { 906 #ifdef CONFIG_USB_DWC3 907 switch (index) { 908 case 0: 909 case 1: 910 if (init == USB_INIT_DEVICE) { 911 ti_usb_phy_uboot_exit(index); 912 dwc3_uboot_exit(index); 913 dwc3_omap_uboot_exit(index); 914 } 915 break; 916 default: 917 printf("Invalid Controller Index\n"); 918 } 919 #endif 920 disable_usb_clocks(index); 921 return 0; 922 } 923 #endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */ 924 925 #ifdef CONFIG_DRIVER_TI_CPSW 926 927 /* Delay value to add to calibrated value */ 928 #define RGMII0_TXCTL_DLY_VAL ((0x3 << 5) + 0x8) 929 #define RGMII0_TXD0_DLY_VAL ((0x3 << 5) + 0x8) 930 #define RGMII0_TXD1_DLY_VAL ((0x3 << 5) + 0x2) 931 #define RGMII0_TXD2_DLY_VAL ((0x4 << 5) + 0x0) 932 #define RGMII0_TXD3_DLY_VAL ((0x4 << 5) + 0x0) 933 #define VIN2A_D13_DLY_VAL ((0x3 << 5) + 0x8) 934 #define VIN2A_D17_DLY_VAL ((0x3 << 5) + 0x8) 935 #define VIN2A_D16_DLY_VAL ((0x3 << 5) + 0x2) 936 #define VIN2A_D15_DLY_VAL ((0x4 << 5) + 0x0) 937 #define VIN2A_D14_DLY_VAL ((0x4 << 5) + 0x0) 938 939 static void cpsw_control(int enabled) 940 { 941 /* VTP can be added here */ 942 } 943 944 static struct cpsw_slave_data cpsw_slaves[] = { 945 { 946 .slave_reg_ofs = 0x208, 947 .sliver_reg_ofs = 0xd80, 948 .phy_addr = 1, 949 }, 950 { 951 .slave_reg_ofs = 0x308, 952 .sliver_reg_ofs = 0xdc0, 953 .phy_addr = 2, 954 }, 955 }; 956 957 static struct cpsw_platform_data cpsw_data = { 958 .mdio_base = CPSW_MDIO_BASE, 959 .cpsw_base = CPSW_BASE, 960 .mdio_div = 0xff, 961 .channels = 8, 962 .cpdma_reg_ofs = 0x800, 963 .slaves = 1, 964 .slave_data = cpsw_slaves, 965 .ale_reg_ofs = 0xd00, 966 .ale_entries = 1024, 967 .host_port_reg_ofs = 0x108, 968 .hw_stats_reg_ofs = 0x900, 969 .bd_ram_ofs = 0x2000, 970 .mac_control = (1 << 5), 971 .control = cpsw_control, 972 .host_port_num = 0, 973 .version = CPSW_CTRL_VERSION_2, 974 }; 975 976 static u64 mac_to_u64(u8 mac[6]) 977 { 978 int i; 979 u64 addr = 0; 980 981 for (i = 0; i < 6; i++) { 982 addr <<= 8; 983 addr |= mac[i]; 984 } 985 986 return addr; 987 } 988 989 static void u64_to_mac(u64 addr, u8 mac[6]) 990 { 991 mac[5] = addr; 992 mac[4] = addr >> 8; 993 mac[3] = addr >> 16; 994 mac[2] = addr >> 24; 995 mac[1] = addr >> 32; 996 mac[0] = addr >> 40; 997 } 998 999 int board_eth_init(bd_t *bis) 1000 { 1001 int ret; 1002 uint8_t mac_addr[6]; 1003 uint32_t mac_hi, mac_lo; 1004 uint32_t ctrl_val; 1005 int i; 1006 u64 mac1, mac2; 1007 u8 mac_addr1[6], mac_addr2[6]; 1008 int num_macs; 1009 1010 /* try reading mac address from efuse */ 1011 mac_lo = readl((*ctrl)->control_core_mac_id_0_lo); 1012 mac_hi = readl((*ctrl)->control_core_mac_id_0_hi); 1013 mac_addr[0] = (mac_hi & 0xFF0000) >> 16; 1014 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 1015 mac_addr[2] = mac_hi & 0xFF; 1016 mac_addr[3] = (mac_lo & 0xFF0000) >> 16; 1017 mac_addr[4] = (mac_lo & 0xFF00) >> 8; 1018 mac_addr[5] = mac_lo & 0xFF; 1019 1020 if (!env_get("ethaddr")) { 1021 printf("<ethaddr> not set. Validating first E-fuse MAC\n"); 1022 1023 if (is_valid_ethaddr(mac_addr)) 1024 eth_env_set_enetaddr("ethaddr", mac_addr); 1025 } 1026 1027 mac_lo = readl((*ctrl)->control_core_mac_id_1_lo); 1028 mac_hi = readl((*ctrl)->control_core_mac_id_1_hi); 1029 mac_addr[0] = (mac_hi & 0xFF0000) >> 16; 1030 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 1031 mac_addr[2] = mac_hi & 0xFF; 1032 mac_addr[3] = (mac_lo & 0xFF0000) >> 16; 1033 mac_addr[4] = (mac_lo & 0xFF00) >> 8; 1034 mac_addr[5] = mac_lo & 0xFF; 1035 1036 if (!env_get("eth1addr")) { 1037 if (is_valid_ethaddr(mac_addr)) 1038 eth_env_set_enetaddr("eth1addr", mac_addr); 1039 } 1040 1041 ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33); 1042 ctrl_val |= 0x22; 1043 writel(ctrl_val, (*ctrl)->control_core_control_io1); 1044 1045 /* The phy address for the AM57xx IDK are different than x15 */ 1046 if (board_is_am572x_idk() || board_is_am571x_idk() || 1047 board_is_am574x_idk()) { 1048 cpsw_data.slave_data[0].phy_addr = 0; 1049 cpsw_data.slave_data[1].phy_addr = 1; 1050 } 1051 1052 ret = cpsw_register(&cpsw_data); 1053 if (ret < 0) 1054 printf("Error %d registering CPSW switch\n", ret); 1055 1056 /* 1057 * Export any Ethernet MAC addresses from EEPROM. 1058 * On AM57xx the 2 MAC addresses define the address range 1059 */ 1060 board_ti_get_eth_mac_addr(0, mac_addr1); 1061 board_ti_get_eth_mac_addr(1, mac_addr2); 1062 1063 if (is_valid_ethaddr(mac_addr1) && is_valid_ethaddr(mac_addr2)) { 1064 mac1 = mac_to_u64(mac_addr1); 1065 mac2 = mac_to_u64(mac_addr2); 1066 1067 /* must contain an address range */ 1068 num_macs = mac2 - mac1 + 1; 1069 /* <= 50 to protect against user programming error */ 1070 if (num_macs > 0 && num_macs <= 50) { 1071 for (i = 0; i < num_macs; i++) { 1072 u64_to_mac(mac1 + i, mac_addr); 1073 if (is_valid_ethaddr(mac_addr)) { 1074 eth_env_set_enetaddr_by_index("eth", 1075 i + 2, 1076 mac_addr); 1077 } 1078 } 1079 } 1080 } 1081 1082 return ret; 1083 } 1084 #endif 1085 1086 #ifdef CONFIG_BOARD_EARLY_INIT_F 1087 /* VTT regulator enable */ 1088 static inline void vtt_regulator_enable(void) 1089 { 1090 if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL) 1091 return; 1092 1093 gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); 1094 gpio_direction_output(GPIO_DDR_VTT_EN, 1); 1095 } 1096 1097 int board_early_init_f(void) 1098 { 1099 vtt_regulator_enable(); 1100 return 0; 1101 } 1102 #endif 1103 1104 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) 1105 int ft_board_setup(void *blob, bd_t *bd) 1106 { 1107 ft_cpu_setup(blob, bd); 1108 1109 return 0; 1110 } 1111 #endif 1112 1113 #ifdef CONFIG_SPL_LOAD_FIT 1114 int board_fit_config_name_match(const char *name) 1115 { 1116 if (board_is_x15()) { 1117 if (board_is_x15_revb1()) { 1118 if (!strcmp(name, "am57xx-beagle-x15-revb1")) 1119 return 0; 1120 } else if (board_is_x15_revc()) { 1121 if (!strcmp(name, "am57xx-beagle-x15-revc")) 1122 return 0; 1123 } else if (!strcmp(name, "am57xx-beagle-x15")) { 1124 return 0; 1125 } 1126 } else if (board_is_am572x_evm() && 1127 !strcmp(name, "am57xx-beagle-x15")) { 1128 return 0; 1129 } else if (board_is_am572x_idk() && !strcmp(name, "am572x-idk")) { 1130 return 0; 1131 } else if (board_is_am574x_idk() && !strcmp(name, "am574x-idk")) { 1132 return 0; 1133 } else if (board_is_am571x_idk() && !strcmp(name, "am571x-idk")) { 1134 return 0; 1135 } 1136 1137 return -1; 1138 } 1139 #endif 1140 1141 #ifdef CONFIG_TI_SECURE_DEVICE 1142 void board_fit_image_post_process(void **p_image, size_t *p_size) 1143 { 1144 secure_boot_verify_image(p_image, p_size); 1145 } 1146 1147 void board_tee_image_process(ulong tee_image, size_t tee_size) 1148 { 1149 secure_tee_install((u32)tee_image); 1150 } 1151 1152 U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TEE, board_tee_image_process); 1153 #endif 1154