1 /* 2 * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com 3 * 4 * Author: Felipe Balbi <balbi@ti.com> 5 * 6 * Based on board/ti/dra7xx/evm.c 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <palmas.h> 13 #include <sata.h> 14 #include <usb.h> 15 #include <asm/omap_common.h> 16 #include <asm/omap_sec_common.h> 17 #include <asm/emif.h> 18 #include <asm/gpio.h> 19 #include <asm/arch/gpio.h> 20 #include <asm/arch/clock.h> 21 #include <asm/arch/dra7xx_iodelay.h> 22 #include <asm/arch/sys_proto.h> 23 #include <asm/arch/mmc_host_def.h> 24 #include <asm/arch/sata.h> 25 #include <asm/arch/gpio.h> 26 #include <asm/arch/omap.h> 27 #include <environment.h> 28 #include <usb.h> 29 #include <linux/usb/gadget.h> 30 #include <dwc3-uboot.h> 31 #include <dwc3-omap-uboot.h> 32 #include <ti-usb-phy-uboot.h> 33 34 #include "../common/board_detect.h" 35 #include "mux_data.h" 36 37 #define board_is_x15() board_ti_is("BBRDX15_") 38 #define board_is_x15_revb1() (board_ti_is("BBRDX15_") && \ 39 !strncmp("B.10", board_ti_get_rev(), 3)) 40 #define board_is_x15_revc() (board_ti_is("BBRDX15_") && \ 41 !strncmp("C.00", board_ti_get_rev(), 3)) 42 #define board_is_am572x_evm() board_ti_is("AM572PM_") 43 #define board_is_am572x_evm_reva3() \ 44 (board_ti_is("AM572PM_") && \ 45 !strncmp("A.30", board_ti_get_rev(), 3)) 46 #define board_is_am572x_idk() board_ti_is("AM572IDK") 47 #define board_is_am571x_idk() board_ti_is("AM571IDK") 48 49 #ifdef CONFIG_DRIVER_TI_CPSW 50 #include <cpsw.h> 51 #endif 52 53 DECLARE_GLOBAL_DATA_PTR; 54 55 #define GPIO_ETH_LCD GPIO_TO_PIN(2, 22) 56 /* GPIO 7_11 */ 57 #define GPIO_DDR_VTT_EN 203 58 59 /* Touch screen controller to identify the LCD */ 60 #define OSD_TS_FT_BUS_ADDRESS 0 61 #define OSD_TS_FT_CHIP_ADDRESS 0x38 62 #define OSD_TS_FT_REG_ID 0xA3 63 /* 64 * Touchscreen IDs for various OSD panels 65 * Ref: http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf 66 */ 67 /* Used on newer osd101t2587 Panels */ 68 #define OSD_TS_FT_ID_5x46 0x54 69 /* Used on older osd101t2045 Panels */ 70 #define OSD_TS_FT_ID_5606 0x08 71 72 #define SYSINFO_BOARD_NAME_MAX_LEN 45 73 74 #define TPS65903X_PRIMARY_SECONDARY_PAD2 0xFB 75 #define TPS65903X_PAD2_POWERHOLD_MASK 0x20 76 77 const struct omap_sysinfo sysinfo = { 78 "Board: UNKNOWN(BeagleBoard X15?) REV UNKNOWN\n" 79 }; 80 81 static const struct dmm_lisa_map_regs beagle_x15_lisa_regs = { 82 .dmm_lisa_map_3 = 0x80740300, 83 .is_ma_present = 0x1 84 }; 85 86 static const struct dmm_lisa_map_regs am571x_idk_lisa_regs = { 87 .dmm_lisa_map_3 = 0x80640100, 88 .is_ma_present = 0x1 89 }; 90 91 void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs) 92 { 93 if (board_is_am571x_idk()) 94 *dmm_lisa_regs = &am571x_idk_lisa_regs; 95 else 96 *dmm_lisa_regs = &beagle_x15_lisa_regs; 97 } 98 99 static const struct emif_regs beagle_x15_emif1_ddr3_532mhz_emif_regs = { 100 .sdram_config_init = 0x61851b32, 101 .sdram_config = 0x61851b32, 102 .sdram_config2 = 0x08000000, 103 .ref_ctrl = 0x000040F1, 104 .ref_ctrl_final = 0x00001035, 105 .sdram_tim1 = 0xcccf36ab, 106 .sdram_tim2 = 0x308f7fda, 107 .sdram_tim3 = 0x409f88a8, 108 .read_idle_ctrl = 0x00050000, 109 .zq_config = 0x5007190b, 110 .temp_alert_config = 0x00000000, 111 .emif_ddr_phy_ctlr_1_init = 0x0024400b, 112 .emif_ddr_phy_ctlr_1 = 0x0e24400b, 113 .emif_ddr_ext_phy_ctrl_1 = 0x10040100, 114 .emif_ddr_ext_phy_ctrl_2 = 0x00910091, 115 .emif_ddr_ext_phy_ctrl_3 = 0x00950095, 116 .emif_ddr_ext_phy_ctrl_4 = 0x009b009b, 117 .emif_ddr_ext_phy_ctrl_5 = 0x009e009e, 118 .emif_rd_wr_lvl_rmp_win = 0x00000000, 119 .emif_rd_wr_lvl_rmp_ctl = 0x80000000, 120 .emif_rd_wr_lvl_ctl = 0x00000000, 121 .emif_rd_wr_exec_thresh = 0x00000305 122 }; 123 124 /* Ext phy ctrl regs 1-35 */ 125 static const u32 beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs[] = { 126 0x10040100, 127 0x00910091, 128 0x00950095, 129 0x009B009B, 130 0x009E009E, 131 0x00980098, 132 0x00340034, 133 0x00350035, 134 0x00340034, 135 0x00310031, 136 0x00340034, 137 0x007F007F, 138 0x007F007F, 139 0x007F007F, 140 0x007F007F, 141 0x007F007F, 142 0x00480048, 143 0x004A004A, 144 0x00520052, 145 0x00550055, 146 0x00500050, 147 0x00000000, 148 0x00600020, 149 0x40011080, 150 0x08102040, 151 0x0, 152 0x0, 153 0x0, 154 0x0, 155 0x0, 156 0x0, 157 0x0, 158 0x0, 159 0x0, 160 0x0 161 }; 162 163 static const struct emif_regs beagle_x15_emif2_ddr3_532mhz_emif_regs = { 164 .sdram_config_init = 0x61851b32, 165 .sdram_config = 0x61851b32, 166 .sdram_config2 = 0x08000000, 167 .ref_ctrl = 0x000040F1, 168 .ref_ctrl_final = 0x00001035, 169 .sdram_tim1 = 0xcccf36b3, 170 .sdram_tim2 = 0x308f7fda, 171 .sdram_tim3 = 0x407f88a8, 172 .read_idle_ctrl = 0x00050000, 173 .zq_config = 0x5007190b, 174 .temp_alert_config = 0x00000000, 175 .emif_ddr_phy_ctlr_1_init = 0x0024400b, 176 .emif_ddr_phy_ctlr_1 = 0x0e24400b, 177 .emif_ddr_ext_phy_ctrl_1 = 0x10040100, 178 .emif_ddr_ext_phy_ctrl_2 = 0x00910091, 179 .emif_ddr_ext_phy_ctrl_3 = 0x00950095, 180 .emif_ddr_ext_phy_ctrl_4 = 0x009b009b, 181 .emif_ddr_ext_phy_ctrl_5 = 0x009e009e, 182 .emif_rd_wr_lvl_rmp_win = 0x00000000, 183 .emif_rd_wr_lvl_rmp_ctl = 0x80000000, 184 .emif_rd_wr_lvl_ctl = 0x00000000, 185 .emif_rd_wr_exec_thresh = 0x00000305 186 }; 187 188 static const u32 beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs[] = { 189 0x10040100, 190 0x00910091, 191 0x00950095, 192 0x009B009B, 193 0x009E009E, 194 0x00980098, 195 0x00340034, 196 0x00350035, 197 0x00340034, 198 0x00310031, 199 0x00340034, 200 0x007F007F, 201 0x007F007F, 202 0x007F007F, 203 0x007F007F, 204 0x007F007F, 205 0x00480048, 206 0x004A004A, 207 0x00520052, 208 0x00550055, 209 0x00500050, 210 0x00000000, 211 0x00600020, 212 0x40011080, 213 0x08102040, 214 0x0, 215 0x0, 216 0x0, 217 0x0, 218 0x0, 219 0x0, 220 0x0, 221 0x0, 222 0x0, 223 0x0 224 }; 225 226 void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs) 227 { 228 switch (emif_nr) { 229 case 1: 230 *regs = &beagle_x15_emif1_ddr3_532mhz_emif_regs; 231 break; 232 case 2: 233 *regs = &beagle_x15_emif2_ddr3_532mhz_emif_regs; 234 break; 235 } 236 } 237 238 void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size) 239 { 240 switch (emif_nr) { 241 case 1: 242 *regs = beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs; 243 *size = ARRAY_SIZE(beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs); 244 break; 245 case 2: 246 *regs = beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs; 247 *size = ARRAY_SIZE(beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs); 248 break; 249 } 250 } 251 252 struct vcores_data beagle_x15_volts = { 253 .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, 254 .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, 255 .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 256 .mpu.addr = TPS659038_REG_ADDR_SMPS12, 257 .mpu.pmic = &tps659038, 258 .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, 259 260 .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, 261 .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, 262 .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, 263 .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, 264 .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, 265 .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, 266 .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, 267 .eve.addr = TPS659038_REG_ADDR_SMPS45, 268 .eve.pmic = &tps659038, 269 .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, 270 271 .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, 272 .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, 273 .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, 274 .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, 275 .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, 276 .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, 277 .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 278 .gpu.addr = TPS659038_REG_ADDR_SMPS45, 279 .gpu.pmic = &tps659038, 280 .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, 281 282 .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, 283 .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, 284 .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, 285 .core.addr = TPS659038_REG_ADDR_SMPS6, 286 .core.pmic = &tps659038, 287 288 .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, 289 .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, 290 .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, 291 .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, 292 .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, 293 .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, 294 .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, 295 .iva.addr = TPS659038_REG_ADDR_SMPS45, 296 .iva.pmic = &tps659038, 297 .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, 298 }; 299 300 struct vcores_data am572x_idk_volts = { 301 .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, 302 .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, 303 .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 304 .mpu.addr = TPS659038_REG_ADDR_SMPS12, 305 .mpu.pmic = &tps659038, 306 .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, 307 308 .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, 309 .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, 310 .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, 311 .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, 312 .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, 313 .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, 314 .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, 315 .eve.addr = TPS659038_REG_ADDR_SMPS45, 316 .eve.pmic = &tps659038, 317 .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, 318 319 .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, 320 .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, 321 .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, 322 .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, 323 .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, 324 .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, 325 .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 326 .gpu.addr = TPS659038_REG_ADDR_SMPS6, 327 .gpu.pmic = &tps659038, 328 .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, 329 330 .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, 331 .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, 332 .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, 333 .core.addr = TPS659038_REG_ADDR_SMPS7, 334 .core.pmic = &tps659038, 335 336 .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, 337 .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, 338 .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, 339 .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, 340 .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, 341 .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, 342 .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, 343 .iva.addr = TPS659038_REG_ADDR_SMPS8, 344 .iva.pmic = &tps659038, 345 .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, 346 }; 347 348 struct vcores_data am571x_idk_volts = { 349 .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, 350 .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, 351 .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 352 .mpu.addr = TPS659038_REG_ADDR_SMPS12, 353 .mpu.pmic = &tps659038, 354 .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, 355 356 .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, 357 .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, 358 .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, 359 .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, 360 .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, 361 .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, 362 .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, 363 .eve.addr = TPS659038_REG_ADDR_SMPS45, 364 .eve.pmic = &tps659038, 365 .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, 366 367 .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, 368 .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, 369 .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, 370 .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, 371 .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, 372 .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, 373 .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, 374 .gpu.addr = TPS659038_REG_ADDR_SMPS6, 375 .gpu.pmic = &tps659038, 376 .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, 377 378 .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, 379 .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, 380 .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, 381 .core.addr = TPS659038_REG_ADDR_SMPS7, 382 .core.pmic = &tps659038, 383 384 .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, 385 .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, 386 .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, 387 .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, 388 .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, 389 .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, 390 .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, 391 .iva.addr = TPS659038_REG_ADDR_SMPS45, 392 .iva.pmic = &tps659038, 393 .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, 394 }; 395 396 int get_voltrail_opp(int rail_offset) 397 { 398 int opp; 399 400 switch (rail_offset) { 401 case VOLT_MPU: 402 opp = DRA7_MPU_OPP; 403 break; 404 case VOLT_CORE: 405 opp = DRA7_CORE_OPP; 406 break; 407 case VOLT_GPU: 408 opp = DRA7_GPU_OPP; 409 break; 410 case VOLT_EVE: 411 opp = DRA7_DSPEVE_OPP; 412 break; 413 case VOLT_IVA: 414 opp = DRA7_IVA_OPP; 415 break; 416 default: 417 opp = OPP_NOM; 418 } 419 420 return opp; 421 } 422 423 424 #ifdef CONFIG_SPL_BUILD 425 /* No env to setup for SPL */ 426 static inline void setup_board_eeprom_env(void) { } 427 428 /* Override function to read eeprom information */ 429 void do_board_detect(void) 430 { 431 int rc; 432 433 rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, 434 CONFIG_EEPROM_CHIP_ADDRESS); 435 if (rc) 436 printf("ti_i2c_eeprom_init failed %d\n", rc); 437 } 438 439 #else /* CONFIG_SPL_BUILD */ 440 441 /* Override function to read eeprom information: actual i2c read done by SPL*/ 442 void do_board_detect(void) 443 { 444 char *bname = NULL; 445 int rc; 446 447 rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, 448 CONFIG_EEPROM_CHIP_ADDRESS); 449 if (rc) 450 printf("ti_i2c_eeprom_init failed %d\n", rc); 451 452 if (board_is_x15()) 453 bname = "BeagleBoard X15"; 454 else if (board_is_am572x_evm()) 455 bname = "AM572x EVM"; 456 else if (board_is_am572x_idk()) 457 bname = "AM572x IDK"; 458 else if (board_is_am571x_idk()) 459 bname = "AM571x IDK"; 460 461 if (bname) 462 snprintf(sysinfo.board_string, SYSINFO_BOARD_NAME_MAX_LEN, 463 "Board: %s REV %s\n", bname, board_ti_get_rev()); 464 } 465 466 static void setup_board_eeprom_env(void) 467 { 468 char *name = "beagle_x15"; 469 int rc; 470 471 rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, 472 CONFIG_EEPROM_CHIP_ADDRESS); 473 if (rc) 474 goto invalid_eeprom; 475 476 if (board_is_x15()) { 477 if (board_is_x15_revb1()) 478 name = "beagle_x15_revb1"; 479 else if (board_is_x15_revc()) 480 name = "beagle_x15_revc"; 481 else 482 name = "beagle_x15"; 483 } else if (board_is_am572x_evm()) { 484 if (board_is_am572x_evm_reva3()) 485 name = "am57xx_evm_reva3"; 486 else 487 name = "am57xx_evm"; 488 } else if (board_is_am572x_idk()) { 489 name = "am572x_idk"; 490 } else if (board_is_am571x_idk()) { 491 name = "am571x_idk"; 492 } else { 493 printf("Unidentified board claims %s in eeprom header\n", 494 board_ti_get_name()); 495 } 496 497 invalid_eeprom: 498 set_board_info_env(name); 499 } 500 501 #endif /* CONFIG_SPL_BUILD */ 502 503 void vcores_init(void) 504 { 505 if (board_is_am572x_idk()) 506 *omap_vcores = &am572x_idk_volts; 507 else if (board_is_am571x_idk()) 508 *omap_vcores = &am571x_idk_volts; 509 else 510 *omap_vcores = &beagle_x15_volts; 511 } 512 513 void hw_data_init(void) 514 { 515 *prcm = &dra7xx_prcm; 516 *dplls_data = &dra7xx_dplls; 517 *ctrl = &dra7xx_ctrl; 518 } 519 520 bool am571x_idk_needs_lcd(void) 521 { 522 bool needs_lcd; 523 524 gpio_request(GPIO_ETH_LCD, "nLCD_Detect"); 525 if (gpio_get_value(GPIO_ETH_LCD)) 526 needs_lcd = false; 527 else 528 needs_lcd = true; 529 530 gpio_free(GPIO_ETH_LCD); 531 532 return needs_lcd; 533 } 534 535 int board_init(void) 536 { 537 gpmc_init(); 538 gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100); 539 540 return 0; 541 } 542 543 void am57x_idk_lcd_detect(void) 544 { 545 int r = -ENODEV; 546 char *idk_lcd = "no"; 547 uint8_t buf = 0; 548 549 /* Only valid for IDKs */ 550 if (board_is_x15() || board_is_am572x_evm()) 551 return; 552 553 /* Only AM571x IDK has gpio control detect.. so check that */ 554 if (board_is_am571x_idk() && !am571x_idk_needs_lcd()) 555 goto out; 556 557 r = i2c_set_bus_num(OSD_TS_FT_BUS_ADDRESS); 558 if (r) { 559 printf("%s: Failed to set bus address to %d: %d\n", 560 __func__, OSD_TS_FT_BUS_ADDRESS, r); 561 goto out; 562 } 563 r = i2c_probe(OSD_TS_FT_CHIP_ADDRESS); 564 if (r) { 565 /* AM572x IDK has no explicit settings for optional LCD kit */ 566 if (board_is_am571x_idk()) { 567 printf("%s: Touch screen detect failed: %d!\n", 568 __func__, r); 569 } 570 goto out; 571 } 572 573 /* Read FT ID */ 574 r = i2c_read(OSD_TS_FT_CHIP_ADDRESS, OSD_TS_FT_REG_ID, 1, &buf, 1); 575 if (r) { 576 printf("%s: Touch screen ID read %d:0x%02x[0x%02x] failed:%d\n", 577 __func__, OSD_TS_FT_BUS_ADDRESS, OSD_TS_FT_CHIP_ADDRESS, 578 OSD_TS_FT_REG_ID, r); 579 goto out; 580 } 581 582 switch (buf) { 583 case OSD_TS_FT_ID_5606: 584 idk_lcd = "osd101t2045"; 585 break; 586 case OSD_TS_FT_ID_5x46: 587 idk_lcd = "osd101t2587"; 588 break; 589 default: 590 printf("%s: Unidentifed Touch screen ID 0x%02x\n", 591 __func__, buf); 592 /* we will let default be "no lcd" */ 593 } 594 out: 595 env_set("idk_lcd", idk_lcd); 596 return; 597 } 598 599 int board_late_init(void) 600 { 601 setup_board_eeprom_env(); 602 u8 val; 603 604 /* 605 * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds 606 * This is the POWERHOLD-in-Low behavior. 607 */ 608 palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1); 609 610 /* 611 * Default FIT boot on HS devices. Non FIT images are not allowed 612 * on HS devices. 613 */ 614 if (get_device_type() == HS_DEVICE) 615 env_set("boot_fit", "1"); 616 617 /* 618 * Set the GPIO7 Pad to POWERHOLD. This has higher priority 619 * over DEV_CTRL.DEV_ON bit. This can be reset in case of 620 * PMIC Power off. So to be on the safer side set it back 621 * to POWERHOLD mode irrespective of the current state. 622 */ 623 palmas_i2c_read_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2, 624 &val); 625 val = val | TPS65903X_PAD2_POWERHOLD_MASK; 626 palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2, 627 val); 628 629 omap_die_id_serial(); 630 omap_set_fastboot_vars(); 631 632 am57x_idk_lcd_detect(); 633 634 #if !defined(CONFIG_SPL_BUILD) 635 board_ti_set_ethaddr(2); 636 #endif 637 638 return 0; 639 } 640 641 void set_muxconf_regs(void) 642 { 643 do_set_mux32((*ctrl)->control_padconf_core_base, 644 early_padconf, ARRAY_SIZE(early_padconf)); 645 } 646 647 #ifdef CONFIG_IODELAY_RECALIBRATION 648 void recalibrate_iodelay(void) 649 { 650 const struct pad_conf_entry *pconf; 651 const struct iodelay_cfg_entry *iod, *delta_iod; 652 int pconf_sz, iod_sz, delta_iod_sz = 0; 653 int ret; 654 655 if (board_is_am572x_idk()) { 656 pconf = core_padconf_array_essential_am572x_idk; 657 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am572x_idk); 658 iod = iodelay_cfg_array_am572x_idk; 659 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am572x_idk); 660 } else if (board_is_am571x_idk()) { 661 pconf = core_padconf_array_essential_am571x_idk; 662 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am571x_idk); 663 iod = iodelay_cfg_array_am571x_idk; 664 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk); 665 } else { 666 /* Common for X15/GPEVM */ 667 pconf = core_padconf_array_essential_x15; 668 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_x15); 669 /* There never was an SR1.0 X15.. So.. */ 670 if (omap_revision() == DRA752_ES1_1) { 671 iod = iodelay_cfg_array_x15_sr1_1; 672 iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr1_1); 673 } else { 674 /* Since full production should switch to SR2.0 */ 675 iod = iodelay_cfg_array_x15_sr2_0; 676 iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr2_0); 677 } 678 } 679 680 /* Setup I/O isolation */ 681 ret = __recalibrate_iodelay_start(); 682 if (ret) 683 goto err; 684 685 /* Do the muxing here */ 686 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz); 687 688 /* Now do the weird minor deltas that should be safe */ 689 if (board_is_x15() || board_is_am572x_evm()) { 690 if (board_is_x15_revb1() || board_is_am572x_evm_reva3() || 691 board_is_x15_revc()) { 692 pconf = core_padconf_array_delta_x15_sr2_0; 693 pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr2_0); 694 } else { 695 pconf = core_padconf_array_delta_x15_sr1_1; 696 pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr1_1); 697 } 698 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz); 699 } 700 701 if (board_is_am571x_idk()) { 702 if (am571x_idk_needs_lcd()) { 703 pconf = core_padconf_array_vout_am571x_idk; 704 pconf_sz = ARRAY_SIZE(core_padconf_array_vout_am571x_idk); 705 delta_iod = iodelay_cfg_array_am571x_idk_4port; 706 delta_iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk_4port); 707 708 } else { 709 pconf = core_padconf_array_icss1eth_am571x_idk; 710 pconf_sz = ARRAY_SIZE(core_padconf_array_icss1eth_am571x_idk); 711 } 712 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz); 713 } 714 715 /* Setup IOdelay configuration */ 716 ret = do_set_iodelay((*ctrl)->iodelay_config_base, iod, iod_sz); 717 if (delta_iod_sz) 718 ret = do_set_iodelay((*ctrl)->iodelay_config_base, delta_iod, 719 delta_iod_sz); 720 721 err: 722 /* Closeup.. remove isolation */ 723 __recalibrate_iodelay_end(ret); 724 } 725 #endif 726 727 #if defined(CONFIG_MMC) 728 int board_mmc_init(bd_t *bis) 729 { 730 omap_mmc_init(0, 0, 0, -1, -1); 731 omap_mmc_init(1, 0, 0, -1, -1); 732 return 0; 733 } 734 #endif 735 736 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT) 737 int spl_start_uboot(void) 738 { 739 /* break into full u-boot on 'c' */ 740 if (serial_tstc() && serial_getc() == 'c') 741 return 1; 742 743 #ifdef CONFIG_SPL_ENV_SUPPORT 744 env_init(); 745 env_load(); 746 if (env_get_yesno("boot_os") != 1) 747 return 1; 748 #endif 749 750 return 0; 751 } 752 #endif 753 754 #ifdef CONFIG_USB_DWC3 755 static struct dwc3_device usb_otg_ss2 = { 756 .maximum_speed = USB_SPEED_HIGH, 757 .base = DRA7_USB_OTG_SS2_BASE, 758 .tx_fifo_resize = false, 759 .index = 1, 760 }; 761 762 static struct dwc3_omap_device usb_otg_ss2_glue = { 763 .base = (void *)DRA7_USB_OTG_SS2_GLUE_BASE, 764 .utmi_mode = DWC3_OMAP_UTMI_MODE_SW, 765 .index = 1, 766 }; 767 768 static struct ti_usb_phy_device usb_phy2_device = { 769 .usb2_phy_power = (void *)DRA7_USB2_PHY2_POWER, 770 .index = 1, 771 }; 772 773 int usb_gadget_handle_interrupts(int index) 774 { 775 u32 status; 776 777 status = dwc3_omap_uboot_interrupt_status(index); 778 if (status) 779 dwc3_uboot_handle_interrupt(index); 780 781 return 0; 782 } 783 #endif /* CONFIG_USB_DWC3 */ 784 785 #if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) 786 int omap_xhci_board_usb_init(int index, enum usb_init_type init) 787 { 788 enable_usb_clocks(index); 789 switch (index) { 790 case 0: 791 if (init == USB_INIT_DEVICE) { 792 printf("port %d can't be used as device\n", index); 793 disable_usb_clocks(index); 794 return -EINVAL; 795 } 796 break; 797 case 1: 798 if (init == USB_INIT_DEVICE) { 799 #ifdef CONFIG_USB_DWC3 800 usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL; 801 usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID; 802 ti_usb_phy_uboot_init(&usb_phy2_device); 803 dwc3_omap_uboot_init(&usb_otg_ss2_glue); 804 dwc3_uboot_init(&usb_otg_ss2); 805 #endif 806 } else { 807 printf("port %d can't be used as host\n", index); 808 disable_usb_clocks(index); 809 return -EINVAL; 810 } 811 812 break; 813 default: 814 printf("Invalid Controller Index\n"); 815 } 816 817 return 0; 818 } 819 820 int omap_xhci_board_usb_cleanup(int index, enum usb_init_type init) 821 { 822 #ifdef CONFIG_USB_DWC3 823 switch (index) { 824 case 0: 825 case 1: 826 if (init == USB_INIT_DEVICE) { 827 ti_usb_phy_uboot_exit(index); 828 dwc3_uboot_exit(index); 829 dwc3_omap_uboot_exit(index); 830 } 831 break; 832 default: 833 printf("Invalid Controller Index\n"); 834 } 835 #endif 836 disable_usb_clocks(index); 837 return 0; 838 } 839 #endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */ 840 841 #ifdef CONFIG_DRIVER_TI_CPSW 842 843 /* Delay value to add to calibrated value */ 844 #define RGMII0_TXCTL_DLY_VAL ((0x3 << 5) + 0x8) 845 #define RGMII0_TXD0_DLY_VAL ((0x3 << 5) + 0x8) 846 #define RGMII0_TXD1_DLY_VAL ((0x3 << 5) + 0x2) 847 #define RGMII0_TXD2_DLY_VAL ((0x4 << 5) + 0x0) 848 #define RGMII0_TXD3_DLY_VAL ((0x4 << 5) + 0x0) 849 #define VIN2A_D13_DLY_VAL ((0x3 << 5) + 0x8) 850 #define VIN2A_D17_DLY_VAL ((0x3 << 5) + 0x8) 851 #define VIN2A_D16_DLY_VAL ((0x3 << 5) + 0x2) 852 #define VIN2A_D15_DLY_VAL ((0x4 << 5) + 0x0) 853 #define VIN2A_D14_DLY_VAL ((0x4 << 5) + 0x0) 854 855 static void cpsw_control(int enabled) 856 { 857 /* VTP can be added here */ 858 } 859 860 static struct cpsw_slave_data cpsw_slaves[] = { 861 { 862 .slave_reg_ofs = 0x208, 863 .sliver_reg_ofs = 0xd80, 864 .phy_addr = 1, 865 }, 866 { 867 .slave_reg_ofs = 0x308, 868 .sliver_reg_ofs = 0xdc0, 869 .phy_addr = 2, 870 }, 871 }; 872 873 static struct cpsw_platform_data cpsw_data = { 874 .mdio_base = CPSW_MDIO_BASE, 875 .cpsw_base = CPSW_BASE, 876 .mdio_div = 0xff, 877 .channels = 8, 878 .cpdma_reg_ofs = 0x800, 879 .slaves = 1, 880 .slave_data = cpsw_slaves, 881 .ale_reg_ofs = 0xd00, 882 .ale_entries = 1024, 883 .host_port_reg_ofs = 0x108, 884 .hw_stats_reg_ofs = 0x900, 885 .bd_ram_ofs = 0x2000, 886 .mac_control = (1 << 5), 887 .control = cpsw_control, 888 .host_port_num = 0, 889 .version = CPSW_CTRL_VERSION_2, 890 }; 891 892 static u64 mac_to_u64(u8 mac[6]) 893 { 894 int i; 895 u64 addr = 0; 896 897 for (i = 0; i < 6; i++) { 898 addr <<= 8; 899 addr |= mac[i]; 900 } 901 902 return addr; 903 } 904 905 static void u64_to_mac(u64 addr, u8 mac[6]) 906 { 907 mac[5] = addr; 908 mac[4] = addr >> 8; 909 mac[3] = addr >> 16; 910 mac[2] = addr >> 24; 911 mac[1] = addr >> 32; 912 mac[0] = addr >> 40; 913 } 914 915 int board_eth_init(bd_t *bis) 916 { 917 int ret; 918 uint8_t mac_addr[6]; 919 uint32_t mac_hi, mac_lo; 920 uint32_t ctrl_val; 921 int i; 922 u64 mac1, mac2; 923 u8 mac_addr1[6], mac_addr2[6]; 924 int num_macs; 925 926 /* try reading mac address from efuse */ 927 mac_lo = readl((*ctrl)->control_core_mac_id_0_lo); 928 mac_hi = readl((*ctrl)->control_core_mac_id_0_hi); 929 mac_addr[0] = (mac_hi & 0xFF0000) >> 16; 930 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 931 mac_addr[2] = mac_hi & 0xFF; 932 mac_addr[3] = (mac_lo & 0xFF0000) >> 16; 933 mac_addr[4] = (mac_lo & 0xFF00) >> 8; 934 mac_addr[5] = mac_lo & 0xFF; 935 936 if (!env_get("ethaddr")) { 937 printf("<ethaddr> not set. Validating first E-fuse MAC\n"); 938 939 if (is_valid_ethaddr(mac_addr)) 940 eth_env_set_enetaddr("ethaddr", mac_addr); 941 } 942 943 mac_lo = readl((*ctrl)->control_core_mac_id_1_lo); 944 mac_hi = readl((*ctrl)->control_core_mac_id_1_hi); 945 mac_addr[0] = (mac_hi & 0xFF0000) >> 16; 946 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 947 mac_addr[2] = mac_hi & 0xFF; 948 mac_addr[3] = (mac_lo & 0xFF0000) >> 16; 949 mac_addr[4] = (mac_lo & 0xFF00) >> 8; 950 mac_addr[5] = mac_lo & 0xFF; 951 952 if (!env_get("eth1addr")) { 953 if (is_valid_ethaddr(mac_addr)) 954 eth_env_set_enetaddr("eth1addr", mac_addr); 955 } 956 957 ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33); 958 ctrl_val |= 0x22; 959 writel(ctrl_val, (*ctrl)->control_core_control_io1); 960 961 /* The phy address for the AM57xx IDK are different than x15 */ 962 if (board_is_am572x_idk() || board_is_am571x_idk()) { 963 cpsw_data.slave_data[0].phy_addr = 0; 964 cpsw_data.slave_data[1].phy_addr = 1; 965 } 966 967 ret = cpsw_register(&cpsw_data); 968 if (ret < 0) 969 printf("Error %d registering CPSW switch\n", ret); 970 971 /* 972 * Export any Ethernet MAC addresses from EEPROM. 973 * On AM57xx the 2 MAC addresses define the address range 974 */ 975 board_ti_get_eth_mac_addr(0, mac_addr1); 976 board_ti_get_eth_mac_addr(1, mac_addr2); 977 978 if (is_valid_ethaddr(mac_addr1) && is_valid_ethaddr(mac_addr2)) { 979 mac1 = mac_to_u64(mac_addr1); 980 mac2 = mac_to_u64(mac_addr2); 981 982 /* must contain an address range */ 983 num_macs = mac2 - mac1 + 1; 984 /* <= 50 to protect against user programming error */ 985 if (num_macs > 0 && num_macs <= 50) { 986 for (i = 0; i < num_macs; i++) { 987 u64_to_mac(mac1 + i, mac_addr); 988 if (is_valid_ethaddr(mac_addr)) { 989 eth_env_set_enetaddr_by_index("eth", 990 i + 2, 991 mac_addr); 992 } 993 } 994 } 995 } 996 997 return ret; 998 } 999 #endif 1000 1001 #ifdef CONFIG_BOARD_EARLY_INIT_F 1002 /* VTT regulator enable */ 1003 static inline void vtt_regulator_enable(void) 1004 { 1005 if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL) 1006 return; 1007 1008 gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); 1009 gpio_direction_output(GPIO_DDR_VTT_EN, 1); 1010 } 1011 1012 int board_early_init_f(void) 1013 { 1014 vtt_regulator_enable(); 1015 return 0; 1016 } 1017 #endif 1018 1019 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) 1020 int ft_board_setup(void *blob, bd_t *bd) 1021 { 1022 ft_cpu_setup(blob, bd); 1023 1024 return 0; 1025 } 1026 #endif 1027 1028 #ifdef CONFIG_SPL_LOAD_FIT 1029 int board_fit_config_name_match(const char *name) 1030 { 1031 if (board_is_x15()) { 1032 if (board_is_x15_revb1()) { 1033 if (!strcmp(name, "am57xx-beagle-x15-revb1")) 1034 return 0; 1035 } else if (!strcmp(name, "am57xx-beagle-x15")) { 1036 return 0; 1037 } 1038 } else if (board_is_am572x_evm() && 1039 !strcmp(name, "am57xx-beagle-x15")) { 1040 return 0; 1041 } else if (board_is_am572x_idk() && !strcmp(name, "am572x-idk")) { 1042 return 0; 1043 } else if (board_is_am571x_idk() && !strcmp(name, "am571x-idk")) { 1044 return 0; 1045 } 1046 1047 return -1; 1048 } 1049 #endif 1050 1051 #ifdef CONFIG_TI_SECURE_DEVICE 1052 void board_fit_image_post_process(void **p_image, size_t *p_size) 1053 { 1054 secure_boot_verify_image(p_image, p_size); 1055 } 1056 1057 void board_tee_image_process(ulong tee_image, size_t tee_size) 1058 { 1059 secure_tee_install((u32)tee_image); 1060 } 1061 1062 U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TEE, board_tee_image_process); 1063 #endif 1064