1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * board.c 4 * 5 * Board functions for TI AM43XX based boards 6 * 7 * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/ 8 */ 9 10 #include <common.h> 11 #include <environment.h> 12 #include <i2c.h> 13 #include <linux/errno.h> 14 #include <spl.h> 15 #include <usb.h> 16 #include <asm/omap_sec_common.h> 17 #include <asm/arch/clock.h> 18 #include <asm/arch/sys_proto.h> 19 #include <asm/arch/mux.h> 20 #include <asm/arch/ddr_defs.h> 21 #include <asm/arch/gpio.h> 22 #include <asm/emif.h> 23 #include <asm/omap_common.h> 24 #include "../common/board_detect.h" 25 #include "board.h" 26 #include <power/pmic.h> 27 #include <power/tps65218.h> 28 #include <power/tps62362.h> 29 #include <miiphy.h> 30 #include <cpsw.h> 31 #include <linux/usb/gadget.h> 32 #include <dwc3-uboot.h> 33 #include <dwc3-omap-uboot.h> 34 #include <ti-usb-phy-uboot.h> 35 36 DECLARE_GLOBAL_DATA_PTR; 37 38 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 39 40 /* 41 * Read header information from EEPROM into global structure. 42 */ 43 #ifdef CONFIG_TI_I2C_BOARD_DETECT 44 void do_board_detect(void) 45 { 46 /* Ensure I2C is initialized for EEPROM access*/ 47 gpi2c_init(); 48 if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, 49 CONFIG_EEPROM_CHIP_ADDRESS)) 50 printf("ti_i2c_eeprom_init failed\n"); 51 } 52 #endif 53 54 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 55 56 const struct dpll_params dpll_mpu[NUM_CRYSTAL_FREQ][NUM_OPPS] = { 57 { /* 19.2 MHz */ 58 {125, 3, 2, -1, -1, -1, -1}, /* OPP 50 */ 59 {-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */ 60 {125, 3, 1, -1, -1, -1, -1}, /* OPP 100 */ 61 {150, 3, 1, -1, -1, -1, -1}, /* OPP 120 */ 62 {125, 2, 1, -1, -1, -1, -1}, /* OPP TB */ 63 {625, 11, 1, -1, -1, -1, -1} /* OPP NT */ 64 }, 65 { /* 24 MHz */ 66 {300, 23, 1, -1, -1, -1, -1}, /* OPP 50 */ 67 {-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */ 68 {600, 23, 1, -1, -1, -1, -1}, /* OPP 100 */ 69 {720, 23, 1, -1, -1, -1, -1}, /* OPP 120 */ 70 {800, 23, 1, -1, -1, -1, -1}, /* OPP TB */ 71 {1000, 23, 1, -1, -1, -1, -1} /* OPP NT */ 72 }, 73 { /* 25 MHz */ 74 {300, 24, 1, -1, -1, -1, -1}, /* OPP 50 */ 75 {-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */ 76 {600, 24, 1, -1, -1, -1, -1}, /* OPP 100 */ 77 {720, 24, 1, -1, -1, -1, -1}, /* OPP 120 */ 78 {800, 24, 1, -1, -1, -1, -1}, /* OPP TB */ 79 {1000, 24, 1, -1, -1, -1, -1} /* OPP NT */ 80 }, 81 { /* 26 MHz */ 82 {300, 25, 1, -1, -1, -1, -1}, /* OPP 50 */ 83 {-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */ 84 {600, 25, 1, -1, -1, -1, -1}, /* OPP 100 */ 85 {720, 25, 1, -1, -1, -1, -1}, /* OPP 120 */ 86 {800, 25, 1, -1, -1, -1, -1}, /* OPP TB */ 87 {1000, 25, 1, -1, -1, -1, -1} /* OPP NT */ 88 }, 89 }; 90 91 const struct dpll_params dpll_core[NUM_CRYSTAL_FREQ] = { 92 {625, 11, -1, -1, 10, 8, 4}, /* 19.2 MHz */ 93 {1000, 23, -1, -1, 10, 8, 4}, /* 24 MHz */ 94 {1000, 24, -1, -1, 10, 8, 4}, /* 25 MHz */ 95 {1000, 25, -1, -1, 10, 8, 4} /* 26 MHz */ 96 }; 97 98 const struct dpll_params dpll_per[NUM_CRYSTAL_FREQ] = { 99 {400, 7, 5, -1, -1, -1, -1}, /* 19.2 MHz */ 100 {400, 9, 5, -1, -1, -1, -1}, /* 24 MHz */ 101 {384, 9, 5, -1, -1, -1, -1}, /* 25 MHz */ 102 {480, 12, 5, -1, -1, -1, -1} /* 26 MHz */ 103 }; 104 105 const struct dpll_params epos_evm_dpll_ddr[NUM_CRYSTAL_FREQ] = { 106 {665, 47, 1, -1, 4, -1, -1}, /*19.2*/ 107 {133, 11, 1, -1, 4, -1, -1}, /* 24 MHz */ 108 {266, 24, 1, -1, 4, -1, -1}, /* 25 MHz */ 109 {133, 12, 1, -1, 4, -1, -1} /* 26 MHz */ 110 }; 111 112 const struct dpll_params gp_evm_dpll_ddr = { 113 50, 2, 1, -1, 2, -1, -1}; 114 115 static const struct dpll_params idk_dpll_ddr = { 116 400, 23, 1, -1, 2, -1, -1 117 }; 118 119 static const u32 ext_phy_ctrl_const_base_lpddr2[] = { 120 0x00500050, 121 0x00350035, 122 0x00350035, 123 0x00350035, 124 0x00350035, 125 0x00350035, 126 0x00000000, 127 0x00000000, 128 0x00000000, 129 0x00000000, 130 0x00000000, 131 0x00000000, 132 0x00000000, 133 0x00000000, 134 0x00000000, 135 0x00000000, 136 0x00000000, 137 0x00000000, 138 0x40001000, 139 0x08102040 140 }; 141 142 const struct ctrl_ioregs ioregs_lpddr2 = { 143 .cm0ioctl = LPDDR2_ADDRCTRL_IOCTRL_VALUE, 144 .cm1ioctl = LPDDR2_ADDRCTRL_WD0_IOCTRL_VALUE, 145 .cm2ioctl = LPDDR2_ADDRCTRL_WD1_IOCTRL_VALUE, 146 .dt0ioctl = LPDDR2_DATA0_IOCTRL_VALUE, 147 .dt1ioctl = LPDDR2_DATA0_IOCTRL_VALUE, 148 .dt2ioctrl = LPDDR2_DATA0_IOCTRL_VALUE, 149 .dt3ioctrl = LPDDR2_DATA0_IOCTRL_VALUE, 150 .emif_sdram_config_ext = 0x1, 151 }; 152 153 const struct emif_regs emif_regs_lpddr2 = { 154 .sdram_config = 0x808012BA, 155 .ref_ctrl = 0x0000040D, 156 .sdram_tim1 = 0xEA86B411, 157 .sdram_tim2 = 0x103A094A, 158 .sdram_tim3 = 0x0F6BA37F, 159 .read_idle_ctrl = 0x00050000, 160 .zq_config = 0x50074BE4, 161 .temp_alert_config = 0x0, 162 .emif_rd_wr_lvl_rmp_win = 0x0, 163 .emif_rd_wr_lvl_rmp_ctl = 0x0, 164 .emif_rd_wr_lvl_ctl = 0x0, 165 .emif_ddr_phy_ctlr_1 = 0x0E284006, 166 .emif_rd_wr_exec_thresh = 0x80000405, 167 .emif_ddr_ext_phy_ctrl_1 = 0x04010040, 168 .emif_ddr_ext_phy_ctrl_2 = 0x00500050, 169 .emif_ddr_ext_phy_ctrl_3 = 0x00500050, 170 .emif_ddr_ext_phy_ctrl_4 = 0x00500050, 171 .emif_ddr_ext_phy_ctrl_5 = 0x00500050, 172 .emif_prio_class_serv_map = 0x80000001, 173 .emif_connect_id_serv_1_map = 0x80000094, 174 .emif_connect_id_serv_2_map = 0x00000000, 175 .emif_cos_config = 0x000FFFFF 176 }; 177 178 const struct ctrl_ioregs ioregs_ddr3 = { 179 .cm0ioctl = DDR3_ADDRCTRL_IOCTRL_VALUE, 180 .cm1ioctl = DDR3_ADDRCTRL_WD0_IOCTRL_VALUE, 181 .cm2ioctl = DDR3_ADDRCTRL_WD1_IOCTRL_VALUE, 182 .dt0ioctl = DDR3_DATA0_IOCTRL_VALUE, 183 .dt1ioctl = DDR3_DATA0_IOCTRL_VALUE, 184 .dt2ioctrl = DDR3_DATA0_IOCTRL_VALUE, 185 .dt3ioctrl = DDR3_DATA0_IOCTRL_VALUE, 186 .emif_sdram_config_ext = 0xc163, 187 }; 188 189 const struct emif_regs ddr3_emif_regs_400Mhz = { 190 .sdram_config = 0x638413B2, 191 .ref_ctrl = 0x00000C30, 192 .sdram_tim1 = 0xEAAAD4DB, 193 .sdram_tim2 = 0x266B7FDA, 194 .sdram_tim3 = 0x107F8678, 195 .read_idle_ctrl = 0x00050000, 196 .zq_config = 0x50074BE4, 197 .temp_alert_config = 0x0, 198 .emif_ddr_phy_ctlr_1 = 0x0E004008, 199 .emif_ddr_ext_phy_ctrl_1 = 0x08020080, 200 .emif_ddr_ext_phy_ctrl_2 = 0x00400040, 201 .emif_ddr_ext_phy_ctrl_3 = 0x00400040, 202 .emif_ddr_ext_phy_ctrl_4 = 0x00400040, 203 .emif_ddr_ext_phy_ctrl_5 = 0x00400040, 204 .emif_rd_wr_lvl_rmp_win = 0x0, 205 .emif_rd_wr_lvl_rmp_ctl = 0x0, 206 .emif_rd_wr_lvl_ctl = 0x0, 207 .emif_rd_wr_exec_thresh = 0x80000405, 208 .emif_prio_class_serv_map = 0x80000001, 209 .emif_connect_id_serv_1_map = 0x80000094, 210 .emif_connect_id_serv_2_map = 0x00000000, 211 .emif_cos_config = 0x000FFFFF 212 }; 213 214 /* EMIF DDR3 Configurations are different for beta AM43X GP EVMs */ 215 const struct emif_regs ddr3_emif_regs_400Mhz_beta = { 216 .sdram_config = 0x638413B2, 217 .ref_ctrl = 0x00000C30, 218 .sdram_tim1 = 0xEAAAD4DB, 219 .sdram_tim2 = 0x266B7FDA, 220 .sdram_tim3 = 0x107F8678, 221 .read_idle_ctrl = 0x00050000, 222 .zq_config = 0x50074BE4, 223 .temp_alert_config = 0x0, 224 .emif_ddr_phy_ctlr_1 = 0x0E004008, 225 .emif_ddr_ext_phy_ctrl_1 = 0x08020080, 226 .emif_ddr_ext_phy_ctrl_2 = 0x00000065, 227 .emif_ddr_ext_phy_ctrl_3 = 0x00000091, 228 .emif_ddr_ext_phy_ctrl_4 = 0x000000B5, 229 .emif_ddr_ext_phy_ctrl_5 = 0x000000E5, 230 .emif_rd_wr_exec_thresh = 0x80000405, 231 .emif_prio_class_serv_map = 0x80000001, 232 .emif_connect_id_serv_1_map = 0x80000094, 233 .emif_connect_id_serv_2_map = 0x00000000, 234 .emif_cos_config = 0x000FFFFF 235 }; 236 237 /* EMIF DDR3 Configurations are different for production AM43X GP EVMs */ 238 const struct emif_regs ddr3_emif_regs_400Mhz_production = { 239 .sdram_config = 0x638413B2, 240 .ref_ctrl = 0x00000C30, 241 .sdram_tim1 = 0xEAAAD4DB, 242 .sdram_tim2 = 0x266B7FDA, 243 .sdram_tim3 = 0x107F8678, 244 .read_idle_ctrl = 0x00050000, 245 .zq_config = 0x50074BE4, 246 .temp_alert_config = 0x0, 247 .emif_ddr_phy_ctlr_1 = 0x0E004008, 248 .emif_ddr_ext_phy_ctrl_1 = 0x08020080, 249 .emif_ddr_ext_phy_ctrl_2 = 0x00000066, 250 .emif_ddr_ext_phy_ctrl_3 = 0x00000091, 251 .emif_ddr_ext_phy_ctrl_4 = 0x000000B9, 252 .emif_ddr_ext_phy_ctrl_5 = 0x000000E6, 253 .emif_rd_wr_exec_thresh = 0x80000405, 254 .emif_prio_class_serv_map = 0x80000001, 255 .emif_connect_id_serv_1_map = 0x80000094, 256 .emif_connect_id_serv_2_map = 0x00000000, 257 .emif_cos_config = 0x000FFFFF 258 }; 259 260 static const struct emif_regs ddr3_sk_emif_regs_400Mhz = { 261 .sdram_config = 0x638413b2, 262 .sdram_config2 = 0x00000000, 263 .ref_ctrl = 0x00000c30, 264 .sdram_tim1 = 0xeaaad4db, 265 .sdram_tim2 = 0x266b7fda, 266 .sdram_tim3 = 0x107f8678, 267 .read_idle_ctrl = 0x00050000, 268 .zq_config = 0x50074be4, 269 .temp_alert_config = 0x0, 270 .emif_ddr_phy_ctlr_1 = 0x0e084008, 271 .emif_ddr_ext_phy_ctrl_1 = 0x08020080, 272 .emif_ddr_ext_phy_ctrl_2 = 0x89, 273 .emif_ddr_ext_phy_ctrl_3 = 0x90, 274 .emif_ddr_ext_phy_ctrl_4 = 0x8e, 275 .emif_ddr_ext_phy_ctrl_5 = 0x8d, 276 .emif_rd_wr_lvl_rmp_win = 0x0, 277 .emif_rd_wr_lvl_rmp_ctl = 0x00000000, 278 .emif_rd_wr_lvl_ctl = 0x00000000, 279 .emif_rd_wr_exec_thresh = 0x80000000, 280 .emif_prio_class_serv_map = 0x80000001, 281 .emif_connect_id_serv_1_map = 0x80000094, 282 .emif_connect_id_serv_2_map = 0x00000000, 283 .emif_cos_config = 0x000FFFFF 284 }; 285 286 static const struct emif_regs ddr3_idk_emif_regs_400Mhz = { 287 .sdram_config = 0x61a11b32, 288 .sdram_config2 = 0x00000000, 289 .ref_ctrl = 0x00000c30, 290 .sdram_tim1 = 0xeaaad4db, 291 .sdram_tim2 = 0x266b7fda, 292 .sdram_tim3 = 0x107f8678, 293 .read_idle_ctrl = 0x00050000, 294 .zq_config = 0x50074be4, 295 .temp_alert_config = 0x00000000, 296 .emif_ddr_phy_ctlr_1 = 0x00008009, 297 .emif_ddr_ext_phy_ctrl_1 = 0x08020080, 298 .emif_ddr_ext_phy_ctrl_2 = 0x00000040, 299 .emif_ddr_ext_phy_ctrl_3 = 0x0000003e, 300 .emif_ddr_ext_phy_ctrl_4 = 0x00000051, 301 .emif_ddr_ext_phy_ctrl_5 = 0x00000051, 302 .emif_rd_wr_lvl_rmp_win = 0x00000000, 303 .emif_rd_wr_lvl_rmp_ctl = 0x00000000, 304 .emif_rd_wr_lvl_ctl = 0x00000000, 305 .emif_rd_wr_exec_thresh = 0x00000405, 306 .emif_prio_class_serv_map = 0x00000000, 307 .emif_connect_id_serv_1_map = 0x00000000, 308 .emif_connect_id_serv_2_map = 0x00000000, 309 .emif_cos_config = 0x00ffffff 310 }; 311 312 void emif_get_ext_phy_ctrl_const_regs(const u32 **regs, u32 *size) 313 { 314 if (board_is_eposevm()) { 315 *regs = ext_phy_ctrl_const_base_lpddr2; 316 *size = ARRAY_SIZE(ext_phy_ctrl_const_base_lpddr2); 317 } 318 319 return; 320 } 321 322 const struct dpll_params *get_dpll_ddr_params(void) 323 { 324 int ind = get_sys_clk_index(); 325 326 if (board_is_eposevm()) 327 return &epos_evm_dpll_ddr[ind]; 328 else if (board_is_evm() || board_is_sk()) 329 return &gp_evm_dpll_ddr; 330 else if (board_is_idk()) 331 return &idk_dpll_ddr; 332 333 printf(" Board '%s' not supported\n", board_ti_get_name()); 334 return NULL; 335 } 336 337 338 /* 339 * get_opp_offset: 340 * Returns the index for safest OPP of the device to boot. 341 * max_off: Index of the MAX OPP in DEV ATTRIBUTE register. 342 * min_off: Index of the MIN OPP in DEV ATTRIBUTE register. 343 * This data is read from dev_attribute register which is e-fused. 344 * A'1' in bit indicates OPP disabled and not available, a '0' indicates 345 * OPP available. Lowest OPP starts with min_off. So returning the 346 * bit with rightmost '0'. 347 */ 348 static int get_opp_offset(int max_off, int min_off) 349 { 350 struct ctrl_stat *ctrl = (struct ctrl_stat *)CTRL_BASE; 351 int opp, offset, i; 352 353 /* Bits 0:11 are defined to be the MPU_MAX_FREQ */ 354 opp = readl(&ctrl->dev_attr) & ~0xFFFFF000; 355 356 for (i = max_off; i >= min_off; i--) { 357 offset = opp & (1 << i); 358 if (!offset) 359 return i; 360 } 361 362 return min_off; 363 } 364 365 const struct dpll_params *get_dpll_mpu_params(void) 366 { 367 int opp = get_opp_offset(DEV_ATTR_MAX_OFFSET, DEV_ATTR_MIN_OFFSET); 368 u32 ind = get_sys_clk_index(); 369 370 return &dpll_mpu[ind][opp]; 371 } 372 373 const struct dpll_params *get_dpll_core_params(void) 374 { 375 int ind = get_sys_clk_index(); 376 377 return &dpll_core[ind]; 378 } 379 380 const struct dpll_params *get_dpll_per_params(void) 381 { 382 int ind = get_sys_clk_index(); 383 384 return &dpll_per[ind]; 385 } 386 387 void scale_vcores_generic(u32 m) 388 { 389 int mpu_vdd, ddr_volt; 390 391 #ifndef CONFIG_DM_I2C 392 if (i2c_probe(TPS65218_CHIP_PM)) 393 return; 394 #else 395 if (power_tps65218_init(0)) 396 return; 397 #endif 398 399 switch (m) { 400 case 1000: 401 mpu_vdd = TPS65218_DCDC_VOLT_SEL_1330MV; 402 break; 403 case 800: 404 mpu_vdd = TPS65218_DCDC_VOLT_SEL_1260MV; 405 break; 406 case 720: 407 mpu_vdd = TPS65218_DCDC_VOLT_SEL_1200MV; 408 break; 409 case 600: 410 mpu_vdd = TPS65218_DCDC_VOLT_SEL_1100MV; 411 break; 412 case 300: 413 mpu_vdd = TPS65218_DCDC_VOLT_SEL_0950MV; 414 break; 415 default: 416 puts("Unknown MPU clock, not scaling\n"); 417 return; 418 } 419 420 /* Set DCDC1 (CORE) voltage to 1.1V */ 421 if (tps65218_voltage_update(TPS65218_DCDC1, 422 TPS65218_DCDC_VOLT_SEL_1100MV)) { 423 printf("%s failure\n", __func__); 424 return; 425 } 426 427 /* Set DCDC2 (MPU) voltage */ 428 if (tps65218_voltage_update(TPS65218_DCDC2, mpu_vdd)) { 429 printf("%s failure\n", __func__); 430 return; 431 } 432 433 if (board_is_eposevm()) 434 ddr_volt = TPS65218_DCDC3_VOLT_SEL_1200MV; 435 else 436 ddr_volt = TPS65218_DCDC3_VOLT_SEL_1350MV; 437 438 /* Set DCDC3 (DDR) voltage */ 439 if (tps65218_voltage_update(TPS65218_DCDC3, ddr_volt)) { 440 printf("%s failure\n", __func__); 441 return; 442 } 443 } 444 445 void scale_vcores_idk(u32 m) 446 { 447 int mpu_vdd; 448 449 #ifndef CONFIG_DM_I2C 450 if (i2c_probe(TPS62362_I2C_ADDR)) 451 return; 452 #else 453 if (power_tps62362_init(0)) 454 return; 455 #endif 456 457 switch (m) { 458 case 1000: 459 mpu_vdd = TPS62362_DCDC_VOLT_SEL_1330MV; 460 break; 461 case 800: 462 mpu_vdd = TPS62362_DCDC_VOLT_SEL_1260MV; 463 break; 464 case 720: 465 mpu_vdd = TPS62362_DCDC_VOLT_SEL_1200MV; 466 break; 467 case 600: 468 mpu_vdd = TPS62362_DCDC_VOLT_SEL_1100MV; 469 break; 470 case 300: 471 mpu_vdd = TPS62362_DCDC_VOLT_SEL_1330MV; 472 break; 473 default: 474 puts("Unknown MPU clock, not scaling\n"); 475 return; 476 } 477 /* Set VDD_MPU voltage */ 478 if (tps62362_voltage_update(TPS62362_SET3, mpu_vdd)) { 479 printf("%s failure\n", __func__); 480 return; 481 } 482 } 483 void gpi2c_init(void) 484 { 485 /* When needed to be invoked prior to BSS initialization */ 486 static bool first_time = true; 487 488 if (first_time) { 489 enable_i2c0_pin_mux(); 490 #ifndef CONFIG_DM_I2C 491 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, 492 CONFIG_SYS_OMAP24_I2C_SLAVE); 493 #endif 494 first_time = false; 495 } 496 } 497 498 void scale_vcores(void) 499 { 500 const struct dpll_params *mpu_params; 501 502 /* Ensure I2C is initialized for PMIC configuration */ 503 gpi2c_init(); 504 505 /* Get the frequency */ 506 mpu_params = get_dpll_mpu_params(); 507 508 if (board_is_idk()) 509 scale_vcores_idk(mpu_params->m); 510 else 511 scale_vcores_generic(mpu_params->m); 512 } 513 514 void set_uart_mux_conf(void) 515 { 516 enable_uart0_pin_mux(); 517 } 518 519 void set_mux_conf_regs(void) 520 { 521 enable_board_pin_mux(); 522 } 523 524 static void enable_vtt_regulator(void) 525 { 526 u32 temp; 527 528 /* enable module */ 529 writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO5_BASE + OMAP_GPIO_CTRL); 530 531 /* enable output for GPIO5_7 */ 532 writel(GPIO_SETDATAOUT(7), 533 AM33XX_GPIO5_BASE + OMAP_GPIO_SETDATAOUT); 534 temp = readl(AM33XX_GPIO5_BASE + OMAP_GPIO_OE); 535 temp = temp & ~(GPIO_OE_ENABLE(7)); 536 writel(temp, AM33XX_GPIO5_BASE + OMAP_GPIO_OE); 537 } 538 539 enum { 540 RTC_BOARD_EPOS = 1, 541 RTC_BOARD_EVM14, 542 RTC_BOARD_EVM12, 543 RTC_BOARD_GPEVM, 544 RTC_BOARD_SK, 545 }; 546 547 /* 548 * In the rtc_only+DRR in self-refresh boot path we have the board type info 549 * in the rtc scratch pad register hence we bypass the costly i2c reads to 550 * eeprom and directly programthe board name string 551 */ 552 void rtc_only_update_board_type(u32 btype) 553 { 554 const char *name = ""; 555 const char *rev = "1.0"; 556 557 switch (btype) { 558 case RTC_BOARD_EPOS: 559 name = "AM43EPOS"; 560 break; 561 case RTC_BOARD_EVM14: 562 name = "AM43__GP"; 563 rev = "1.4"; 564 break; 565 case RTC_BOARD_EVM12: 566 name = "AM43__GP"; 567 rev = "1.2"; 568 break; 569 case RTC_BOARD_GPEVM: 570 name = "AM43__GP"; 571 break; 572 case RTC_BOARD_SK: 573 name = "AM43__SK"; 574 break; 575 } 576 ti_i2c_eeprom_am_set(name, rev); 577 } 578 579 u32 rtc_only_get_board_type(void) 580 { 581 if (board_is_eposevm()) 582 return RTC_BOARD_EPOS; 583 else if (board_is_evm_14_or_later()) 584 return RTC_BOARD_EVM14; 585 else if (board_is_evm_12_or_later()) 586 return RTC_BOARD_EVM12; 587 else if (board_is_gpevm()) 588 return RTC_BOARD_GPEVM; 589 else if (board_is_sk()) 590 return RTC_BOARD_SK; 591 592 return 0; 593 } 594 595 void sdram_init(void) 596 { 597 /* 598 * EPOS EVM has 1GB LPDDR2 connected to EMIF. 599 * GP EMV has 1GB DDR3 connected to EMIF 600 * along with VTT regulator. 601 */ 602 if (board_is_eposevm()) { 603 config_ddr(0, &ioregs_lpddr2, NULL, NULL, &emif_regs_lpddr2, 0); 604 } else if (board_is_evm_14_or_later()) { 605 enable_vtt_regulator(); 606 config_ddr(0, &ioregs_ddr3, NULL, NULL, 607 &ddr3_emif_regs_400Mhz_production, 0); 608 } else if (board_is_evm_12_or_later()) { 609 enable_vtt_regulator(); 610 config_ddr(0, &ioregs_ddr3, NULL, NULL, 611 &ddr3_emif_regs_400Mhz_beta, 0); 612 } else if (board_is_evm()) { 613 enable_vtt_regulator(); 614 config_ddr(0, &ioregs_ddr3, NULL, NULL, 615 &ddr3_emif_regs_400Mhz, 0); 616 } else if (board_is_sk()) { 617 config_ddr(400, &ioregs_ddr3, NULL, NULL, 618 &ddr3_sk_emif_regs_400Mhz, 0); 619 } else if (board_is_idk()) { 620 config_ddr(400, &ioregs_ddr3, NULL, NULL, 621 &ddr3_idk_emif_regs_400Mhz, 0); 622 } 623 } 624 #endif 625 626 /* setup board specific PMIC */ 627 int power_init_board(void) 628 { 629 int rc; 630 #ifndef CONFIG_DM_I2C 631 struct pmic *p = NULL; 632 #endif 633 if (board_is_idk()) { 634 rc = power_tps62362_init(0); 635 if (rc) 636 goto done; 637 #ifndef CONFIG_DM_I2C 638 p = pmic_get("TPS62362"); 639 if (!p || pmic_probe(p)) 640 goto done; 641 #endif 642 puts("PMIC: TPS62362\n"); 643 } else { 644 rc = power_tps65218_init(0); 645 if (rc) 646 goto done; 647 #ifndef CONFIG_DM_I2C 648 p = pmic_get("TPS65218_PMIC"); 649 if (!p || pmic_probe(p)) 650 goto done; 651 #endif 652 puts("PMIC: TPS65218\n"); 653 } 654 done: 655 return 0; 656 } 657 658 int board_init(void) 659 { 660 struct l3f_cfg_bwlimiter *bwlimiter = (struct l3f_cfg_bwlimiter *)L3F_CFG_BWLIMITER; 661 u32 mreqprio_0, mreqprio_1, modena_init0_bw_fractional, 662 modena_init0_bw_integer, modena_init0_watermark_0; 663 664 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 665 gpmc_init(); 666 667 /* 668 * Call this to initialize *ctrl again 669 */ 670 hw_data_init(); 671 672 /* Clear all important bits for DSS errata that may need to be tweaked*/ 673 mreqprio_0 = readl(&cdev->mreqprio_0) & MREQPRIO_0_SAB_INIT1_MASK & 674 MREQPRIO_0_SAB_INIT0_MASK; 675 676 mreqprio_1 = readl(&cdev->mreqprio_1) & MREQPRIO_1_DSS_MASK; 677 678 modena_init0_bw_fractional = readl(&bwlimiter->modena_init0_bw_fractional) & 679 BW_LIMITER_BW_FRAC_MASK; 680 681 modena_init0_bw_integer = readl(&bwlimiter->modena_init0_bw_integer) & 682 BW_LIMITER_BW_INT_MASK; 683 684 modena_init0_watermark_0 = readl(&bwlimiter->modena_init0_watermark_0) & 685 BW_LIMITER_BW_WATERMARK_MASK; 686 687 /* Setting MReq Priority of the DSS*/ 688 mreqprio_0 |= 0x77; 689 690 /* 691 * Set L3 Fast Configuration Register 692 * Limiting bandwith for ARM core to 700 MBPS 693 */ 694 modena_init0_bw_fractional |= 0x10; 695 modena_init0_bw_integer |= 0x3; 696 697 writel(mreqprio_0, &cdev->mreqprio_0); 698 writel(mreqprio_1, &cdev->mreqprio_1); 699 700 writel(modena_init0_bw_fractional, &bwlimiter->modena_init0_bw_fractional); 701 writel(modena_init0_bw_integer, &bwlimiter->modena_init0_bw_integer); 702 writel(modena_init0_watermark_0, &bwlimiter->modena_init0_watermark_0); 703 704 return 0; 705 } 706 707 #ifdef CONFIG_BOARD_LATE_INIT 708 #if CONFIG_IS_ENABLED(DM_USB) && CONFIG_IS_ENABLED(OF_CONTROL) 709 static int device_okay(const char *path) 710 { 711 int node; 712 713 node = fdt_path_offset(gd->fdt_blob, path); 714 if (node < 0) 715 return 0; 716 717 return fdtdec_get_is_enabled(gd->fdt_blob, node); 718 } 719 #endif 720 721 int board_late_init(void) 722 { 723 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 724 set_board_info_env(NULL); 725 726 /* 727 * Default FIT boot on HS devices. Non FIT images are not allowed 728 * on HS devices. 729 */ 730 if (get_device_type() == HS_DEVICE) 731 env_set("boot_fit", "1"); 732 #endif 733 734 #if CONFIG_IS_ENABLED(DM_USB) && CONFIG_IS_ENABLED(OF_CONTROL) 735 if (device_okay("/ocp/omap_dwc3@48380000")) 736 enable_usb_clocks(0); 737 if (device_okay("/ocp/omap_dwc3@483c0000")) 738 enable_usb_clocks(1); 739 #endif 740 return 0; 741 } 742 #endif 743 744 #if !CONFIG_IS_ENABLED(DM_USB_GADGET) 745 #ifdef CONFIG_USB_DWC3 746 static struct dwc3_device usb_otg_ss1 = { 747 .maximum_speed = USB_SPEED_HIGH, 748 .base = USB_OTG_SS1_BASE, 749 .tx_fifo_resize = false, 750 .index = 0, 751 }; 752 753 static struct dwc3_omap_device usb_otg_ss1_glue = { 754 .base = (void *)USB_OTG_SS1_GLUE_BASE, 755 .utmi_mode = DWC3_OMAP_UTMI_MODE_SW, 756 .index = 0, 757 }; 758 759 static struct ti_usb_phy_device usb_phy1_device = { 760 .usb2_phy_power = (void *)USB2_PHY1_POWER, 761 .index = 0, 762 }; 763 764 static struct dwc3_device usb_otg_ss2 = { 765 .maximum_speed = USB_SPEED_HIGH, 766 .base = USB_OTG_SS2_BASE, 767 .tx_fifo_resize = false, 768 .index = 1, 769 }; 770 771 static struct dwc3_omap_device usb_otg_ss2_glue = { 772 .base = (void *)USB_OTG_SS2_GLUE_BASE, 773 .utmi_mode = DWC3_OMAP_UTMI_MODE_SW, 774 .index = 1, 775 }; 776 777 static struct ti_usb_phy_device usb_phy2_device = { 778 .usb2_phy_power = (void *)USB2_PHY2_POWER, 779 .index = 1, 780 }; 781 782 int usb_gadget_handle_interrupts(int index) 783 { 784 u32 status; 785 786 status = dwc3_omap_uboot_interrupt_status(index); 787 if (status) 788 dwc3_uboot_handle_interrupt(index); 789 790 return 0; 791 } 792 #endif /* CONFIG_USB_DWC3 */ 793 794 #if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) 795 int board_usb_init(int index, enum usb_init_type init) 796 { 797 enable_usb_clocks(index); 798 #ifdef CONFIG_USB_DWC3 799 switch (index) { 800 case 0: 801 if (init == USB_INIT_DEVICE) { 802 usb_otg_ss1.dr_mode = USB_DR_MODE_PERIPHERAL; 803 usb_otg_ss1_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID; 804 dwc3_omap_uboot_init(&usb_otg_ss1_glue); 805 ti_usb_phy_uboot_init(&usb_phy1_device); 806 dwc3_uboot_init(&usb_otg_ss1); 807 } 808 break; 809 case 1: 810 if (init == USB_INIT_DEVICE) { 811 usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL; 812 usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID; 813 ti_usb_phy_uboot_init(&usb_phy2_device); 814 dwc3_omap_uboot_init(&usb_otg_ss2_glue); 815 dwc3_uboot_init(&usb_otg_ss2); 816 } 817 break; 818 default: 819 printf("Invalid Controller Index\n"); 820 } 821 #endif 822 823 return 0; 824 } 825 826 int board_usb_cleanup(int index, enum usb_init_type init) 827 { 828 #ifdef CONFIG_USB_DWC3 829 switch (index) { 830 case 0: 831 case 1: 832 if (init == USB_INIT_DEVICE) { 833 ti_usb_phy_uboot_exit(index); 834 dwc3_uboot_exit(index); 835 dwc3_omap_uboot_exit(index); 836 } 837 break; 838 default: 839 printf("Invalid Controller Index\n"); 840 } 841 #endif 842 disable_usb_clocks(index); 843 844 return 0; 845 } 846 #endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */ 847 #endif /* !CONFIG_IS_ENABLED(DM_USB_GADGET) */ 848 849 #ifdef CONFIG_DRIVER_TI_CPSW 850 851 static void cpsw_control(int enabled) 852 { 853 /* Additional controls can be added here */ 854 return; 855 } 856 857 static struct cpsw_slave_data cpsw_slaves[] = { 858 { 859 .slave_reg_ofs = 0x208, 860 .sliver_reg_ofs = 0xd80, 861 .phy_addr = 16, 862 }, 863 { 864 .slave_reg_ofs = 0x308, 865 .sliver_reg_ofs = 0xdc0, 866 .phy_addr = 1, 867 }, 868 }; 869 870 static struct cpsw_platform_data cpsw_data = { 871 .mdio_base = CPSW_MDIO_BASE, 872 .cpsw_base = CPSW_BASE, 873 .mdio_div = 0xff, 874 .channels = 8, 875 .cpdma_reg_ofs = 0x800, 876 .slaves = 1, 877 .slave_data = cpsw_slaves, 878 .ale_reg_ofs = 0xd00, 879 .ale_entries = 1024, 880 .host_port_reg_ofs = 0x108, 881 .hw_stats_reg_ofs = 0x900, 882 .bd_ram_ofs = 0x2000, 883 .mac_control = (1 << 5), 884 .control = cpsw_control, 885 .host_port_num = 0, 886 .version = CPSW_CTRL_VERSION_2, 887 }; 888 889 int board_eth_init(bd_t *bis) 890 { 891 int rv; 892 uint8_t mac_addr[6]; 893 uint32_t mac_hi, mac_lo; 894 895 /* try reading mac address from efuse */ 896 mac_lo = readl(&cdev->macid0l); 897 mac_hi = readl(&cdev->macid0h); 898 mac_addr[0] = mac_hi & 0xFF; 899 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 900 mac_addr[2] = (mac_hi & 0xFF0000) >> 16; 901 mac_addr[3] = (mac_hi & 0xFF000000) >> 24; 902 mac_addr[4] = mac_lo & 0xFF; 903 mac_addr[5] = (mac_lo & 0xFF00) >> 8; 904 905 if (!env_get("ethaddr")) { 906 puts("<ethaddr> not set. Validating first E-fuse MAC\n"); 907 if (is_valid_ethaddr(mac_addr)) 908 eth_env_set_enetaddr("ethaddr", mac_addr); 909 } 910 911 mac_lo = readl(&cdev->macid1l); 912 mac_hi = readl(&cdev->macid1h); 913 mac_addr[0] = mac_hi & 0xFF; 914 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 915 mac_addr[2] = (mac_hi & 0xFF0000) >> 16; 916 mac_addr[3] = (mac_hi & 0xFF000000) >> 24; 917 mac_addr[4] = mac_lo & 0xFF; 918 mac_addr[5] = (mac_lo & 0xFF00) >> 8; 919 920 if (!env_get("eth1addr")) { 921 if (is_valid_ethaddr(mac_addr)) 922 eth_env_set_enetaddr("eth1addr", mac_addr); 923 } 924 925 if (board_is_eposevm()) { 926 writel(RMII_MODE_ENABLE | RMII_CHIPCKL_ENABLE, &cdev->miisel); 927 cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RMII; 928 cpsw_slaves[0].phy_addr = 16; 929 } else if (board_is_sk()) { 930 writel(RGMII_MODE_ENABLE, &cdev->miisel); 931 cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RGMII; 932 cpsw_slaves[0].phy_addr = 4; 933 cpsw_slaves[1].phy_addr = 5; 934 } else if (board_is_idk()) { 935 writel(RGMII_MODE_ENABLE, &cdev->miisel); 936 cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RGMII; 937 cpsw_slaves[0].phy_addr = 0; 938 } else { 939 writel(RGMII_MODE_ENABLE, &cdev->miisel); 940 cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RGMII; 941 cpsw_slaves[0].phy_addr = 0; 942 } 943 944 rv = cpsw_register(&cpsw_data); 945 if (rv < 0) 946 printf("Error %d registering CPSW switch\n", rv); 947 948 return rv; 949 } 950 #endif 951 952 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) 953 int ft_board_setup(void *blob, bd_t *bd) 954 { 955 ft_cpu_setup(blob, bd); 956 957 return 0; 958 } 959 #endif 960 961 #if defined(CONFIG_SPL_LOAD_FIT) || defined(CONFIG_DTB_RESELECT) 962 int board_fit_config_name_match(const char *name) 963 { 964 bool eeprom_read = board_ti_was_eeprom_read(); 965 966 if (!strcmp(name, "am4372-generic") && !eeprom_read) 967 return 0; 968 else if (board_is_evm() && !strcmp(name, "am437x-gp-evm")) 969 return 0; 970 else if (board_is_sk() && !strcmp(name, "am437x-sk-evm")) 971 return 0; 972 else if (board_is_eposevm() && !strcmp(name, "am43x-epos-evm")) 973 return 0; 974 else if (board_is_idk() && !strcmp(name, "am437x-idk-evm")) 975 return 0; 976 else 977 return -1; 978 } 979 #endif 980 981 #ifdef CONFIG_DTB_RESELECT 982 int embedded_dtb_select(void) 983 { 984 do_board_detect(); 985 fdtdec_setup(); 986 987 return 0; 988 } 989 #endif 990 991 #ifdef CONFIG_TI_SECURE_DEVICE 992 void board_fit_image_post_process(const void *fit, int node, void **p_image, size_t *p_size) 993 { 994 secure_boot_verify_image(p_image, p_size); 995 } 996 997 void board_tee_image_process(ulong tee_image, size_t tee_size) 998 { 999 secure_tee_install((u32)tee_image); 1000 } 1001 1002 U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TEE, board_tee_image_process); 1003 #endif 1004