1 /* 2 * board.c 3 * 4 * Board functions for TI AM335X based boards 5 * 6 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <errno.h> 13 #include <spl.h> 14 #include <asm/arch/cpu.h> 15 #include <asm/arch/hardware.h> 16 #include <asm/arch/omap.h> 17 #include <asm/arch/ddr_defs.h> 18 #include <asm/arch/clock.h> 19 #include <asm/arch/gpio.h> 20 #include <asm/arch/mmc_host_def.h> 21 #include <asm/arch/sys_proto.h> 22 #include <asm/arch/mem.h> 23 #include <asm/io.h> 24 #include <asm/emif.h> 25 #include <asm/gpio.h> 26 #include <i2c.h> 27 #include <miiphy.h> 28 #include <cpsw.h> 29 #include <power/tps65217.h> 30 #include <power/tps65910.h> 31 #include <environment.h> 32 #include <watchdog.h> 33 #include <environment.h> 34 #include "board.h" 35 36 DECLARE_GLOBAL_DATA_PTR; 37 38 /* GPIO that controls power to DDR on EVM-SK */ 39 #define GPIO_DDR_VTT_EN 7 40 41 #if defined(CONFIG_SPL_BUILD) || \ 42 (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_DM_ETH)) 43 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 44 #endif 45 46 /* 47 * Read header information from EEPROM into global structure. 48 */ 49 static int read_eeprom(struct am335x_baseboard_id *header) 50 { 51 /* Check if baseboard eeprom is available */ 52 if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) { 53 puts("Could not probe the EEPROM; something fundamentally " 54 "wrong on the I2C bus.\n"); 55 return -ENODEV; 56 } 57 58 /* read the eeprom using i2c */ 59 if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header, 60 sizeof(struct am335x_baseboard_id))) { 61 puts("Could not read the EEPROM; something fundamentally" 62 " wrong on the I2C bus.\n"); 63 return -EIO; 64 } 65 66 if (header->magic != 0xEE3355AA) { 67 /* 68 * read the eeprom using i2c again, 69 * but use only a 1 byte address 70 */ 71 if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header, 72 sizeof(struct am335x_baseboard_id))) { 73 puts("Could not read the EEPROM; something " 74 "fundamentally wrong on the I2C bus.\n"); 75 return -EIO; 76 } 77 78 if (header->magic != 0xEE3355AA) { 79 printf("Incorrect magic number (0x%x) in EEPROM\n", 80 header->magic); 81 return -EINVAL; 82 } 83 } 84 85 return 0; 86 } 87 88 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 89 static const struct ddr_data ddr2_data = { 90 .datardsratio0 = MT47H128M16RT25E_RD_DQS, 91 .datafwsratio0 = MT47H128M16RT25E_PHY_FIFO_WE, 92 .datawrsratio0 = MT47H128M16RT25E_PHY_WR_DATA, 93 }; 94 95 static const struct cmd_control ddr2_cmd_ctrl_data = { 96 .cmd0csratio = MT47H128M16RT25E_RATIO, 97 98 .cmd1csratio = MT47H128M16RT25E_RATIO, 99 100 .cmd2csratio = MT47H128M16RT25E_RATIO, 101 }; 102 103 static const struct emif_regs ddr2_emif_reg_data = { 104 .sdram_config = MT47H128M16RT25E_EMIF_SDCFG, 105 .ref_ctrl = MT47H128M16RT25E_EMIF_SDREF, 106 .sdram_tim1 = MT47H128M16RT25E_EMIF_TIM1, 107 .sdram_tim2 = MT47H128M16RT25E_EMIF_TIM2, 108 .sdram_tim3 = MT47H128M16RT25E_EMIF_TIM3, 109 .emif_ddr_phy_ctlr_1 = MT47H128M16RT25E_EMIF_READ_LATENCY, 110 }; 111 112 static const struct ddr_data ddr3_data = { 113 .datardsratio0 = MT41J128MJT125_RD_DQS, 114 .datawdsratio0 = MT41J128MJT125_WR_DQS, 115 .datafwsratio0 = MT41J128MJT125_PHY_FIFO_WE, 116 .datawrsratio0 = MT41J128MJT125_PHY_WR_DATA, 117 }; 118 119 static const struct ddr_data ddr3_beagleblack_data = { 120 .datardsratio0 = MT41K256M16HA125E_RD_DQS, 121 .datawdsratio0 = MT41K256M16HA125E_WR_DQS, 122 .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE, 123 .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA, 124 }; 125 126 static const struct ddr_data ddr3_evm_data = { 127 .datardsratio0 = MT41J512M8RH125_RD_DQS, 128 .datawdsratio0 = MT41J512M8RH125_WR_DQS, 129 .datafwsratio0 = MT41J512M8RH125_PHY_FIFO_WE, 130 .datawrsratio0 = MT41J512M8RH125_PHY_WR_DATA, 131 }; 132 133 static const struct cmd_control ddr3_cmd_ctrl_data = { 134 .cmd0csratio = MT41J128MJT125_RATIO, 135 .cmd0iclkout = MT41J128MJT125_INVERT_CLKOUT, 136 137 .cmd1csratio = MT41J128MJT125_RATIO, 138 .cmd1iclkout = MT41J128MJT125_INVERT_CLKOUT, 139 140 .cmd2csratio = MT41J128MJT125_RATIO, 141 .cmd2iclkout = MT41J128MJT125_INVERT_CLKOUT, 142 }; 143 144 static const struct cmd_control ddr3_beagleblack_cmd_ctrl_data = { 145 .cmd0csratio = MT41K256M16HA125E_RATIO, 146 .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 147 148 .cmd1csratio = MT41K256M16HA125E_RATIO, 149 .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 150 151 .cmd2csratio = MT41K256M16HA125E_RATIO, 152 .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 153 }; 154 155 static const struct cmd_control ddr3_evm_cmd_ctrl_data = { 156 .cmd0csratio = MT41J512M8RH125_RATIO, 157 .cmd0iclkout = MT41J512M8RH125_INVERT_CLKOUT, 158 159 .cmd1csratio = MT41J512M8RH125_RATIO, 160 .cmd1iclkout = MT41J512M8RH125_INVERT_CLKOUT, 161 162 .cmd2csratio = MT41J512M8RH125_RATIO, 163 .cmd2iclkout = MT41J512M8RH125_INVERT_CLKOUT, 164 }; 165 166 static struct emif_regs ddr3_emif_reg_data = { 167 .sdram_config = MT41J128MJT125_EMIF_SDCFG, 168 .ref_ctrl = MT41J128MJT125_EMIF_SDREF, 169 .sdram_tim1 = MT41J128MJT125_EMIF_TIM1, 170 .sdram_tim2 = MT41J128MJT125_EMIF_TIM2, 171 .sdram_tim3 = MT41J128MJT125_EMIF_TIM3, 172 .zq_config = MT41J128MJT125_ZQ_CFG, 173 .emif_ddr_phy_ctlr_1 = MT41J128MJT125_EMIF_READ_LATENCY | 174 PHY_EN_DYN_PWRDN, 175 }; 176 177 static struct emif_regs ddr3_beagleblack_emif_reg_data = { 178 .sdram_config = MT41K256M16HA125E_EMIF_SDCFG, 179 .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF, 180 .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1, 181 .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2, 182 .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3, 183 .zq_config = MT41K256M16HA125E_ZQ_CFG, 184 .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY, 185 }; 186 187 static struct emif_regs ddr3_evm_emif_reg_data = { 188 .sdram_config = MT41J512M8RH125_EMIF_SDCFG, 189 .ref_ctrl = MT41J512M8RH125_EMIF_SDREF, 190 .sdram_tim1 = MT41J512M8RH125_EMIF_TIM1, 191 .sdram_tim2 = MT41J512M8RH125_EMIF_TIM2, 192 .sdram_tim3 = MT41J512M8RH125_EMIF_TIM3, 193 .zq_config = MT41J512M8RH125_ZQ_CFG, 194 .emif_ddr_phy_ctlr_1 = MT41J512M8RH125_EMIF_READ_LATENCY | 195 PHY_EN_DYN_PWRDN, 196 }; 197 198 #ifdef CONFIG_SPL_OS_BOOT 199 int spl_start_uboot(void) 200 { 201 /* break into full u-boot on 'c' */ 202 if (serial_tstc() && serial_getc() == 'c') 203 return 1; 204 205 #ifdef CONFIG_SPL_ENV_SUPPORT 206 env_init(); 207 env_relocate_spec(); 208 if (getenv_yesno("boot_os") != 1) 209 return 1; 210 #endif 211 212 return 0; 213 } 214 #endif 215 216 #define OSC (V_OSCK/1000000) 217 const struct dpll_params dpll_ddr = { 218 266, OSC-1, 1, -1, -1, -1, -1}; 219 const struct dpll_params dpll_ddr_evm_sk = { 220 303, OSC-1, 1, -1, -1, -1, -1}; 221 const struct dpll_params dpll_ddr_bone_black = { 222 400, OSC-1, 1, -1, -1, -1, -1}; 223 224 void am33xx_spl_board_init(void) 225 { 226 struct am335x_baseboard_id header; 227 int mpu_vdd; 228 229 if (read_eeprom(&header) < 0) 230 puts("Could not get board ID.\n"); 231 232 /* Get the frequency */ 233 dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); 234 235 if (board_is_bone(&header) || board_is_bone_lt(&header)) { 236 /* BeagleBone PMIC Code */ 237 int usb_cur_lim; 238 239 /* 240 * Only perform PMIC configurations if board rev > A1 241 * on Beaglebone White 242 */ 243 if (board_is_bone(&header) && !strncmp(header.version, 244 "00A1", 4)) 245 return; 246 247 if (i2c_probe(TPS65217_CHIP_PM)) 248 return; 249 250 /* 251 * On Beaglebone White we need to ensure we have AC power 252 * before increasing the frequency. 253 */ 254 if (board_is_bone(&header)) { 255 uchar pmic_status_reg; 256 if (tps65217_reg_read(TPS65217_STATUS, 257 &pmic_status_reg)) 258 return; 259 if (!(pmic_status_reg & TPS65217_PWR_SRC_AC_BITMASK)) { 260 puts("No AC power, disabling frequency switch\n"); 261 return; 262 } 263 } 264 265 /* 266 * Override what we have detected since we know if we have 267 * a Beaglebone Black it supports 1GHz. 268 */ 269 if (board_is_bone_lt(&header)) 270 dpll_mpu_opp100.m = MPUPLL_M_1000; 271 272 /* 273 * Increase USB current limit to 1300mA or 1800mA and set 274 * the MPU voltage controller as needed. 275 */ 276 if (dpll_mpu_opp100.m == MPUPLL_M_1000) { 277 usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA; 278 mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV; 279 } else { 280 usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA; 281 mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV; 282 } 283 284 if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, 285 TPS65217_POWER_PATH, 286 usb_cur_lim, 287 TPS65217_USB_INPUT_CUR_LIMIT_MASK)) 288 puts("tps65217_reg_write failure\n"); 289 290 /* Set DCDC3 (CORE) voltage to 1.125V */ 291 if (tps65217_voltage_update(TPS65217_DEFDCDC3, 292 TPS65217_DCDC_VOLT_SEL_1125MV)) { 293 puts("tps65217_voltage_update failure\n"); 294 return; 295 } 296 297 /* Set CORE Frequencies to OPP100 */ 298 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); 299 300 /* Set DCDC2 (MPU) voltage */ 301 if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) { 302 puts("tps65217_voltage_update failure\n"); 303 return; 304 } 305 306 /* 307 * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone. 308 * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black. 309 */ 310 if (board_is_bone(&header)) { 311 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, 312 TPS65217_DEFLS1, 313 TPS65217_LDO_VOLTAGE_OUT_3_3, 314 TPS65217_LDO_MASK)) 315 puts("tps65217_reg_write failure\n"); 316 } else { 317 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, 318 TPS65217_DEFLS1, 319 TPS65217_LDO_VOLTAGE_OUT_1_8, 320 TPS65217_LDO_MASK)) 321 puts("tps65217_reg_write failure\n"); 322 } 323 324 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, 325 TPS65217_DEFLS2, 326 TPS65217_LDO_VOLTAGE_OUT_3_3, 327 TPS65217_LDO_MASK)) 328 puts("tps65217_reg_write failure\n"); 329 } else { 330 int sil_rev; 331 332 /* 333 * The GP EVM, IDK and EVM SK use a TPS65910 PMIC. For all 334 * MPU frequencies we support we use a CORE voltage of 335 * 1.1375V. For MPU voltage we need to switch based on 336 * the frequency we are running at. 337 */ 338 if (i2c_probe(TPS65910_CTRL_I2C_ADDR)) 339 return; 340 341 /* 342 * Depending on MPU clock and PG we will need a different 343 * VDD to drive at that speed. 344 */ 345 sil_rev = readl(&cdev->deviceid) >> 28; 346 mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev, 347 dpll_mpu_opp100.m); 348 349 /* Tell the TPS65910 to use i2c */ 350 tps65910_set_i2c_control(); 351 352 /* First update MPU voltage. */ 353 if (tps65910_voltage_update(MPU, mpu_vdd)) 354 return; 355 356 /* Second, update the CORE voltage. */ 357 if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_3)) 358 return; 359 360 /* Set CORE Frequencies to OPP100 */ 361 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); 362 } 363 364 /* Set MPU Frequency to what we detected now that voltages are set */ 365 do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100); 366 } 367 368 const struct dpll_params *get_dpll_ddr_params(void) 369 { 370 struct am335x_baseboard_id header; 371 372 enable_i2c0_pin_mux(); 373 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); 374 if (read_eeprom(&header) < 0) 375 puts("Could not get board ID.\n"); 376 377 if (board_is_evm_sk(&header)) 378 return &dpll_ddr_evm_sk; 379 else if (board_is_bone_lt(&header)) 380 return &dpll_ddr_bone_black; 381 else if (board_is_evm_15_or_later(&header)) 382 return &dpll_ddr_evm_sk; 383 else 384 return &dpll_ddr; 385 } 386 387 void set_uart_mux_conf(void) 388 { 389 #if CONFIG_CONS_INDEX == 1 390 enable_uart0_pin_mux(); 391 #elif CONFIG_CONS_INDEX == 2 392 enable_uart1_pin_mux(); 393 #elif CONFIG_CONS_INDEX == 3 394 enable_uart2_pin_mux(); 395 #elif CONFIG_CONS_INDEX == 4 396 enable_uart3_pin_mux(); 397 #elif CONFIG_CONS_INDEX == 5 398 enable_uart4_pin_mux(); 399 #elif CONFIG_CONS_INDEX == 6 400 enable_uart5_pin_mux(); 401 #endif 402 } 403 404 void set_mux_conf_regs(void) 405 { 406 __maybe_unused struct am335x_baseboard_id header; 407 408 if (read_eeprom(&header) < 0) 409 puts("Could not get board ID.\n"); 410 411 enable_board_pin_mux(&header); 412 } 413 414 const struct ctrl_ioregs ioregs_evmsk = { 415 .cm0ioctl = MT41J128MJT125_IOCTRL_VALUE, 416 .cm1ioctl = MT41J128MJT125_IOCTRL_VALUE, 417 .cm2ioctl = MT41J128MJT125_IOCTRL_VALUE, 418 .dt0ioctl = MT41J128MJT125_IOCTRL_VALUE, 419 .dt1ioctl = MT41J128MJT125_IOCTRL_VALUE, 420 }; 421 422 const struct ctrl_ioregs ioregs_bonelt = { 423 .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 424 .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 425 .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 426 .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 427 .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 428 }; 429 430 const struct ctrl_ioregs ioregs_evm15 = { 431 .cm0ioctl = MT41J512M8RH125_IOCTRL_VALUE, 432 .cm1ioctl = MT41J512M8RH125_IOCTRL_VALUE, 433 .cm2ioctl = MT41J512M8RH125_IOCTRL_VALUE, 434 .dt0ioctl = MT41J512M8RH125_IOCTRL_VALUE, 435 .dt1ioctl = MT41J512M8RH125_IOCTRL_VALUE, 436 }; 437 438 const struct ctrl_ioregs ioregs = { 439 .cm0ioctl = MT47H128M16RT25E_IOCTRL_VALUE, 440 .cm1ioctl = MT47H128M16RT25E_IOCTRL_VALUE, 441 .cm2ioctl = MT47H128M16RT25E_IOCTRL_VALUE, 442 .dt0ioctl = MT47H128M16RT25E_IOCTRL_VALUE, 443 .dt1ioctl = MT47H128M16RT25E_IOCTRL_VALUE, 444 }; 445 446 void sdram_init(void) 447 { 448 __maybe_unused struct am335x_baseboard_id header; 449 450 if (read_eeprom(&header) < 0) 451 puts("Could not get board ID.\n"); 452 453 if (board_is_evm_sk(&header)) { 454 /* 455 * EVM SK 1.2A and later use gpio0_7 to enable DDR3. 456 * This is safe enough to do on older revs. 457 */ 458 gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); 459 gpio_direction_output(GPIO_DDR_VTT_EN, 1); 460 } 461 462 if (board_is_evm_sk(&header)) 463 config_ddr(303, &ioregs_evmsk, &ddr3_data, 464 &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0); 465 else if (board_is_bone_lt(&header)) 466 config_ddr(400, &ioregs_bonelt, 467 &ddr3_beagleblack_data, 468 &ddr3_beagleblack_cmd_ctrl_data, 469 &ddr3_beagleblack_emif_reg_data, 0); 470 else if (board_is_evm_15_or_later(&header)) 471 config_ddr(303, &ioregs_evm15, &ddr3_evm_data, 472 &ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0); 473 else 474 config_ddr(266, &ioregs, &ddr2_data, 475 &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0); 476 } 477 #endif 478 479 /* 480 * Basic board specific setup. Pinmux has been handled already. 481 */ 482 int board_init(void) 483 { 484 #if defined(CONFIG_HW_WATCHDOG) 485 hw_watchdog_init(); 486 #endif 487 488 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 489 #if defined(CONFIG_NOR) || defined(CONFIG_NAND) 490 gpmc_init(); 491 #endif 492 return 0; 493 } 494 495 #ifdef CONFIG_BOARD_LATE_INIT 496 int board_late_init(void) 497 { 498 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 499 char safe_string[HDR_NAME_LEN + 1]; 500 struct am335x_baseboard_id header; 501 502 if (read_eeprom(&header) < 0) 503 puts("Could not get board ID.\n"); 504 505 /* Now set variables based on the header. */ 506 strncpy(safe_string, (char *)header.name, sizeof(header.name)); 507 safe_string[sizeof(header.name)] = 0; 508 setenv("board_name", safe_string); 509 510 strncpy(safe_string, (char *)header.version, sizeof(header.version)); 511 safe_string[sizeof(header.version)] = 0; 512 setenv("board_rev", safe_string); 513 #endif 514 515 return 0; 516 } 517 #endif 518 519 #ifndef CONFIG_DM_ETH 520 521 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 522 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 523 static void cpsw_control(int enabled) 524 { 525 /* VTP can be added here */ 526 527 return; 528 } 529 530 static struct cpsw_slave_data cpsw_slaves[] = { 531 { 532 .slave_reg_ofs = 0x208, 533 .sliver_reg_ofs = 0xd80, 534 .phy_addr = 0, 535 }, 536 { 537 .slave_reg_ofs = 0x308, 538 .sliver_reg_ofs = 0xdc0, 539 .phy_addr = 1, 540 }, 541 }; 542 543 static struct cpsw_platform_data cpsw_data = { 544 .mdio_base = CPSW_MDIO_BASE, 545 .cpsw_base = CPSW_BASE, 546 .mdio_div = 0xff, 547 .channels = 8, 548 .cpdma_reg_ofs = 0x800, 549 .slaves = 1, 550 .slave_data = cpsw_slaves, 551 .ale_reg_ofs = 0xd00, 552 .ale_entries = 1024, 553 .host_port_reg_ofs = 0x108, 554 .hw_stats_reg_ofs = 0x900, 555 .bd_ram_ofs = 0x2000, 556 .mac_control = (1 << 5), 557 .control = cpsw_control, 558 .host_port_num = 0, 559 .version = CPSW_CTRL_VERSION_2, 560 }; 561 #endif 562 563 /* 564 * This function will: 565 * Read the eFuse for MAC addresses, and set ethaddr/eth1addr/usbnet_devaddr 566 * in the environment 567 * Perform fixups to the PHY present on certain boards. We only need this 568 * function in: 569 * - SPL with either CPSW or USB ethernet support 570 * - Full U-Boot, with either CPSW or USB ethernet 571 * Build in only these cases to avoid warnings about unused variables 572 * when we build an SPL that has neither option but full U-Boot will. 573 */ 574 #if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) \ 575 && defined(CONFIG_SPL_BUILD)) || \ 576 ((defined(CONFIG_DRIVER_TI_CPSW) || \ 577 defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \ 578 !defined(CONFIG_SPL_BUILD)) 579 int board_eth_init(bd_t *bis) 580 { 581 int rv, n = 0; 582 uint8_t mac_addr[6]; 583 uint32_t mac_hi, mac_lo; 584 __maybe_unused struct am335x_baseboard_id header; 585 586 /* try reading mac address from efuse */ 587 mac_lo = readl(&cdev->macid0l); 588 mac_hi = readl(&cdev->macid0h); 589 mac_addr[0] = mac_hi & 0xFF; 590 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 591 mac_addr[2] = (mac_hi & 0xFF0000) >> 16; 592 mac_addr[3] = (mac_hi & 0xFF000000) >> 24; 593 mac_addr[4] = mac_lo & 0xFF; 594 mac_addr[5] = (mac_lo & 0xFF00) >> 8; 595 596 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 597 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 598 if (!getenv("ethaddr")) { 599 printf("<ethaddr> not set. Validating first E-fuse MAC\n"); 600 601 if (is_valid_ethaddr(mac_addr)) 602 eth_setenv_enetaddr("ethaddr", mac_addr); 603 } 604 605 #ifdef CONFIG_DRIVER_TI_CPSW 606 607 mac_lo = readl(&cdev->macid1l); 608 mac_hi = readl(&cdev->macid1h); 609 mac_addr[0] = mac_hi & 0xFF; 610 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 611 mac_addr[2] = (mac_hi & 0xFF0000) >> 16; 612 mac_addr[3] = (mac_hi & 0xFF000000) >> 24; 613 mac_addr[4] = mac_lo & 0xFF; 614 mac_addr[5] = (mac_lo & 0xFF00) >> 8; 615 616 if (!getenv("eth1addr")) { 617 if (is_valid_ethaddr(mac_addr)) 618 eth_setenv_enetaddr("eth1addr", mac_addr); 619 } 620 621 if (read_eeprom(&header) < 0) 622 puts("Could not get board ID.\n"); 623 624 if (board_is_bone(&header) || board_is_bone_lt(&header) || 625 board_is_idk(&header)) { 626 writel(MII_MODE_ENABLE, &cdev->miisel); 627 cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if = 628 PHY_INTERFACE_MODE_MII; 629 } else { 630 writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel); 631 cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if = 632 PHY_INTERFACE_MODE_RGMII; 633 } 634 635 rv = cpsw_register(&cpsw_data); 636 if (rv < 0) 637 printf("Error %d registering CPSW switch\n", rv); 638 else 639 n += rv; 640 #endif 641 642 /* 643 * 644 * CPSW RGMII Internal Delay Mode is not supported in all PVT 645 * operating points. So we must set the TX clock delay feature 646 * in the AR8051 PHY. Since we only support a single ethernet 647 * device in U-Boot, we only do this for the first instance. 648 */ 649 #define AR8051_PHY_DEBUG_ADDR_REG 0x1d 650 #define AR8051_PHY_DEBUG_DATA_REG 0x1e 651 #define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5 652 #define AR8051_RGMII_TX_CLK_DLY 0x100 653 654 if (board_is_evm_sk(&header) || board_is_gp_evm(&header)) { 655 const char *devname; 656 devname = miiphy_get_current_dev(); 657 658 miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_ADDR_REG, 659 AR8051_DEBUG_RGMII_CLK_DLY_REG); 660 miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_DATA_REG, 661 AR8051_RGMII_TX_CLK_DLY); 662 } 663 #endif 664 #if defined(CONFIG_USB_ETHER) && \ 665 (!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USBETH_SUPPORT)) 666 if (is_valid_ethaddr(mac_addr)) 667 eth_setenv_enetaddr("usbnet_devaddr", mac_addr); 668 669 rv = usb_eth_initialize(bis); 670 if (rv < 0) 671 printf("Error %d registering USB_ETHER\n", rv); 672 else 673 n += rv; 674 #endif 675 return n; 676 } 677 #endif 678 679 #endif /* CONFIG_DM_ETH */ 680