1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
4  */
5 
6 #include <common.h>
7 #include <i2c.h>
8 #include <pci.h>
9 #include <asm/gpio.h>
10 #include <asm/io.h>
11 #include <asm/arch/cpu.h>
12 #include <asm/arch/soc.h>
13 #include <linux/crc8.h>
14 #include <linux/mbus.h>
15 #ifdef CONFIG_NET
16 #include <netdev.h>
17 #endif
18 #include "theadorable.h"
19 
20 #include "../drivers/ddr/marvell/axp/ddr3_hw_training.h"
21 #include "../arch/arm/mach-mvebu/serdes/axp/high_speed_env_spec.h"
22 
23 DECLARE_GLOBAL_DATA_PTR;
24 
25 #define MV_USB_PHY_BASE			(MVEBU_AXP_USB_BASE + 0x800)
26 #define PHY_CHANNEL_RX_CTRL0_REG(port, chan) \
27 	(MV_USB_PHY_BASE + ((port) << 12) + ((chan) << 6) + 0x8)
28 
29 #define THEADORABLE_GPP_OUT_ENA_LOW	0x00336780
30 #define THEADORABLE_GPP_OUT_ENA_MID	0x00003cf0
31 #define THEADORABLE_GPP_OUT_ENA_HIGH	(~(0x0))
32 
33 #define THEADORABLE_GPP_OUT_VAL_LOW	0x2c0c983f
34 #define THEADORABLE_GPP_OUT_VAL_MID	0x0007000c
35 #define THEADORABLE_GPP_OUT_VAL_HIGH	0x00000000
36 
37 #define GPIO_USB0_PWR_ON		18
38 #define GPIO_USB1_PWR_ON		19
39 
40 #define PEX_SWITCH_NOT_FOUNT_LIMIT	3
41 
42 #define STM_I2C_BUS	1
43 #define STM_I2C_ADDR	0x27
44 #define REBOOT_DELAY	1000		/* reboot-delay in ms */
45 
46 /* DDR3 static configuration */
47 static MV_DRAM_MC_INIT ddr3_theadorable[MV_MAX_DDR3_STATIC_SIZE] = {
48 	{0x00001400, 0x7301ca28},	/* DDR SDRAM Configuration Register */
49 	{0x00001404, 0x30000800},	/* Dunit Control Low Register */
50 	{0x00001408, 0x44149887},	/* DDR SDRAM Timing (Low) Register */
51 	{0x0000140C, 0x38d93fc7},	/* DDR SDRAM Timing (High) Register */
52 	{0x00001410, 0x1b100001},	/* DDR SDRAM Address Control Register */
53 	{0x00001424, 0x0000f3ff},	/* Dunit Control High Register */
54 	{0x00001428, 0x000f8830},	/* ODT Timing (Low) Register */
55 	{0x0000142C, 0x014c50f4},	/* DDR3 Timing Register */
56 	{0x0000147C, 0x0000c671},	/* ODT Timing (High) Register */
57 
58 	{0x00001494, 0x00010000},	/* DDR SDRAM ODT Control (Low) Reg */
59 	{0x0000149C, 0x00000001},	/* DDR Dunit ODT Control Register */
60 	{0x000014A0, 0x00000001},	/* DRAM FIFO Control Register */
61 	{0x000014A8, 0x00000101},	/* AXI Control Register */
62 
63 	/*
64 	 * DO NOT Modify - Open Mbus Window - 2G - Mbus is required for the
65 	 * training sequence
66 	 */
67 	{0x000200e8, 0x3fff0e01},
68 	{0x00020184, 0x3fffffe0},	/* Close fast path Window to - 2G */
69 
70 	{0x0001504, 0x7fffffe1},	/* CS0 Size */
71 	{0x000150C, 0x00000000},	/* CS1 Size */
72 	{0x0001514, 0x00000000},	/* CS2 Size */
73 	{0x000151C, 0x00000000},	/* CS3 Size */
74 
75 	{0x00020220, 0x00000007},	/* Reserved */
76 
77 	{0x00001538, 0x00000009},	/* Read Data Sample Delays Register */
78 	{0x0000153C, 0x00000009},	/* Read Data Ready Delay Register */
79 
80 	{0x000015D0, 0x00000650},	/* MR0 */
81 	{0x000015D4, 0x00000044},	/* MR1 */
82 	{0x000015D8, 0x00000010},	/* MR2 */
83 	{0x000015DC, 0x00000000},	/* MR3 */
84 	{0x000015E0, 0x00000001},
85 	{0x000015E4, 0x00203c18},	/* ZQDS Configuration Register */
86 	{0x000015EC, 0xf800a225},	/* DDR PHY */
87 
88 	/* Recommended Settings from Marvell for 4 x 16 bit devices: */
89 	{0x000014C0, 0x192424c9},	/* DRAM addr and Ctrl Driving Strenght*/
90 	{0x000014C4, 0x0aaa24c9},	/* DRAM Data and DQS Driving Strenght */
91 
92 	{0x0, 0x0}
93 };
94 
95 static MV_DRAM_MODES board_ddr_modes[MV_DDR3_MODES_NUMBER] = {
96 	{"theadorable_1333-667", 0x3, 0x5, 0x0, A0, ddr3_theadorable,  NULL},
97 };
98 
99 extern MV_SERDES_CHANGE_M_PHY serdes_change_m_phy[];
100 
101 /*
102  * Lane0 - PCIE0.0 X1 (to WIFI Module)
103  * Lane5 - SATA0
104  * Lane6 - SATA1
105  * Lane7 - SGMII0 (to Ethernet Phy)
106  * Lane8-11 - PCIE2.0 X4 (to PEX Switch)
107  * all other lanes are disabled
108  */
109 MV_BIN_SERDES_CFG theadorable_serdes_cfg[] = {
110 	{ MV_PEX_ROOT_COMPLEX, 0x22200001, 0x00001111,
111 	  { PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4,
112 	    PEX_BUS_DISABLED },
113 	  0x0060, serdes_change_m_phy
114 	},
115 };
116 
117 /*
118  * Define a board-specific detection pulse-width array for the SerDes PCIe
119  * interfaces. If not defined in the board code, the default of currently 2
120  * is used. Values from 0...3 are possible (2 bits).
121  */
122 u8 serdes_pex_pulse_width[4] = { 0, 2, 2, 2 };
123 
124 MV_DRAM_MODES *ddr3_get_static_ddr_mode(void)
125 {
126 	/* Only one mode supported for this board */
127 	return &board_ddr_modes[0];
128 }
129 
130 MV_BIN_SERDES_CFG *board_serdes_cfg_get(u8 pex_mode)
131 {
132 	return &theadorable_serdes_cfg[0];
133 }
134 
135 u8 board_sat_r_get(u8 dev_num, u8 reg)
136 {
137 	/* Bit 0 enables PCI 2.0 link capabilities instead of PCI 1.x */
138 	return 0x01;
139 }
140 
141 int board_early_init_f(void)
142 {
143 	/* Configure MPP */
144 	writel(0x00000000, MVEBU_MPP_BASE + 0x00);
145 	writel(0x03300000, MVEBU_MPP_BASE + 0x04);
146 	writel(0x00000033, MVEBU_MPP_BASE + 0x08);
147 	writel(0x00000000, MVEBU_MPP_BASE + 0x0c);
148 	writel(0x11110000, MVEBU_MPP_BASE + 0x10);
149 	writel(0x00221100, MVEBU_MPP_BASE + 0x14);
150 	writel(0x00000000, MVEBU_MPP_BASE + 0x18);
151 	writel(0x00000000, MVEBU_MPP_BASE + 0x1c);
152 	writel(0x00000000, MVEBU_MPP_BASE + 0x20);
153 
154 	/* Configure GPIO */
155 	writel(THEADORABLE_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
156 	writel(THEADORABLE_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
157 	writel(THEADORABLE_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
158 	writel(THEADORABLE_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
159 	writel(THEADORABLE_GPP_OUT_VAL_HIGH, MVEBU_GPIO2_BASE + 0x00);
160 	writel(THEADORABLE_GPP_OUT_ENA_HIGH, MVEBU_GPIO2_BASE + 0x04);
161 
162 	return 0;
163 }
164 
165 int board_init(void)
166 {
167 	int ret;
168 
169 	/* adress of boot parameters */
170 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
171 
172 	/*
173 	 * Map SPI devices via MBUS so that they can be accessed via
174 	 * the SPI direct access mode
175 	 */
176 	mbus_dt_setup_win(&mbus_state, SPI_BUS0_DEV1_BASE, SPI_BUS0_DEV1_SIZE,
177 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI0_CS1);
178 	mbus_dt_setup_win(&mbus_state, SPI_BUS1_DEV2_BASE, SPI_BUS0_DEV1_SIZE,
179 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI1_CS2);
180 
181 	/*
182 	 * Set RX Channel Control 0 Register:
183 	 * Tests have shown, that setting the LPF_COEF from 0 (1/8)
184 	 * to 3 (1/1) results in a more stable USB connection.
185 	 */
186 	setbits_le32(PHY_CHANNEL_RX_CTRL0_REG(0, 1), 0xc);
187 	setbits_le32(PHY_CHANNEL_RX_CTRL0_REG(0, 2), 0xc);
188 	setbits_le32(PHY_CHANNEL_RX_CTRL0_REG(0, 3), 0xc);
189 
190 	/* Toggle USB power */
191 	ret = gpio_request(GPIO_USB0_PWR_ON, "USB0_PWR_ON");
192 	if (ret < 0)
193 		return ret;
194 	gpio_direction_output(GPIO_USB0_PWR_ON, 0);
195 	ret = gpio_request(GPIO_USB1_PWR_ON, "USB1_PWR_ON");
196 	if (ret < 0)
197 		return ret;
198 	gpio_direction_output(GPIO_USB1_PWR_ON, 0);
199 	mdelay(1);
200 	gpio_set_value(GPIO_USB0_PWR_ON, 1);
201 	gpio_set_value(GPIO_USB1_PWR_ON, 1);
202 
203 	return 0;
204 }
205 
206 int checkboard(void)
207 {
208 	board_fpga_add();
209 
210 	return 0;
211 }
212 
213 #ifdef CONFIG_NET
214 int board_eth_init(bd_t *bis)
215 {
216 	cpu_eth_init(bis); /* Built in controller(s) come first */
217 	return pci_eth_init(bis);
218 }
219 #endif
220 
221 int board_video_init(void)
222 {
223 	struct mvebu_lcd_info lcd_info;
224 
225 	/* Reserved memory area via CONFIG_SYS_MEM_TOP_HIDE */
226 	lcd_info.fb_base	= gd->ram_size;
227 	lcd_info.x_res		= 240;
228 	lcd_info.x_fp		= 1;
229 	lcd_info.x_bp		= 45;
230 	lcd_info.y_res		= 320;
231 	lcd_info.y_fp		= 1;
232 	lcd_info.y_bp		= 3;
233 
234 	return mvebu_lcd_register_init(&lcd_info);
235 }
236 
237 #ifdef CONFIG_BOARD_LATE_INIT
238 int board_late_init(void)
239 {
240 	pci_dev_t bdf;
241 	ulong bootcount;
242 
243 	/*
244 	 * Check if the PEX switch is detected (somtimes its not available
245 	 * on the PCIe bus). In this case, try to recover by issuing a
246 	 * soft-reset or even a power-cycle, depending on the bootcounter
247 	 * value.
248 	 */
249 	bdf = pci_find_device(PCI_VENDOR_ID_PLX, 0x8619, 0);
250 	if (bdf == -1) {
251 		u8 i2c_buf[8];
252 		int ret;
253 
254 		/* PEX switch not found! */
255 		bootcount = bootcount_load();
256 		printf("Failed to find PLX PEX-switch (bootcount=%ld)\n",
257 		       bootcount);
258 		if (bootcount > PEX_SWITCH_NOT_FOUNT_LIMIT) {
259 			printf("Issuing power-switch via uC!\n");
260 
261 			printf("Issuing power-switch via uC!\n");
262 			i2c_set_bus_num(STM_I2C_BUS);
263 			i2c_buf[0] = STM_I2C_ADDR << 1;
264 			i2c_buf[1] = 0xc5;	/* cmd */
265 			i2c_buf[2] = 0x01;	/* enable */
266 			/* Delay before reboot */
267 			i2c_buf[3] = REBOOT_DELAY & 0x00ff;
268 			i2c_buf[4] = (REBOOT_DELAY & 0xff00) >> 8;
269 			/* Delay before shutdown */
270 			i2c_buf[5] = 0x00;
271 			i2c_buf[6] = 0x00;
272 			i2c_buf[7] = crc8(0x72, &i2c_buf[0], 7);
273 
274 			ret = i2c_write(STM_I2C_ADDR, 0, 0, &i2c_buf[1], 7);
275 			if (ret) {
276 				printf("I2C write error (ret=%d)\n", ret);
277 				printf("Issuing soft-reset...\n");
278 				/* default handling: SOFT reset */
279 				do_reset(NULL, 0, 0, NULL);
280 			}
281 
282 			/* Wait for power-cycle to occur... */
283 			printf("Waiting for power-cycle via uC...\n");
284 			while (1)
285 				;
286 		} else {
287 			printf("Issuing soft-reset...\n");
288 			/* default handling: SOFT reset */
289 			do_reset(NULL, 0, 0, NULL);
290 		}
291 	}
292 
293 	return 0;
294 }
295 #endif
296 
297 #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_PCI)
298 int do_pcie_test(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
299 {
300 	pci_dev_t bdf;
301 	u16 ven_id, dev_id;
302 
303 	if (argc != 3)
304 		return cmd_usage(cmdtp);
305 
306 	ven_id = simple_strtoul(argv[1], NULL, 16);
307 	dev_id = simple_strtoul(argv[2], NULL, 16);
308 
309 	printf("Checking for PCIe device: VendorID 0x%04x, DeviceId 0x%04x\n",
310 	       ven_id, dev_id);
311 
312 	/*
313 	 * Check if the PCIe device is detected (somtimes its not available
314 	 * on the PCIe bus)
315 	 */
316 	bdf = pci_find_device(ven_id, dev_id, 0);
317 	if (bdf == -1) {
318 		/* PCIe device not found! */
319 		printf("Failed to find PCIe device\n");
320 	} else {
321 		/* PCIe device found! */
322 		printf("PCIe device found, resetting board...\n");
323 
324 		/* default handling: SOFT reset */
325 		do_reset(NULL, 0, 0, NULL);
326 	}
327 
328 	return 0;
329 }
330 
331 U_BOOT_CMD(
332 	pcie,   3,   0,     do_pcie_test,
333 	"Test for presence of a PCIe device",
334 	"<VendorID> <DeviceID>"
335 );
336 #endif
337