1 /*
2  * Maintainer :
3  *      Tapani Utriainen <linuxfae@technexion.com>
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 #include <common.h>
8 #include <netdev.h>
9 #include <twl4030.h>
10 #include <asm/io.h>
11 #include <asm/arch/mmc_host_def.h>
12 #include <asm/arch/mem.h>
13 #include <asm/arch/mux.h>
14 #include <asm/arch/sys_proto.h>
15 #include <asm/arch/gpio.h>
16 #include <asm/gpio.h>
17 #include <asm/mach-types.h>
18 
19 #include <usb.h>
20 #include <asm/ehci-omap.h>
21 
22 #include "tao3530.h"
23 
24 DECLARE_GLOBAL_DATA_PTR;
25 
26 int tao3530_revision(void)
27 {
28 	int ret = 0;
29 
30 	/* char *label argument is unused in gpio_request() */
31 	ret = gpio_request(65, "");
32 	if (ret) {
33 		puts("Error: GPIO 65 not available\n");
34 		goto out;
35 	}
36 	MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M4));
37 
38 	ret = gpio_request(1, "");
39 	if (ret) {
40 		puts("Error: GPIO 1 not available\n");
41 		goto out2;
42 	}
43 	MUX_VAL(CP(SYS_CLKREQ), (IEN  | PTU | EN | M4));
44 
45 	ret = gpio_direction_input(65);
46 	if (ret) {
47 		puts("Error: GPIO 65 not available for input\n");
48 		goto out3;
49 	}
50 
51 	ret =  gpio_direction_input(1);
52 	if (ret) {
53 		puts("Error: GPIO 1 not available for input\n");
54 		goto out3;
55 	}
56 
57 	ret = gpio_get_value(65) << 1 | gpio_get_value(1);
58 
59 out3:
60 	MUX_VAL(CP(SYS_CLKREQ), (IEN  | PTU | EN | M0));
61 	gpio_free(1);
62 out2:
63 	MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M0));
64 	gpio_free(65);
65 out:
66 
67 	return ret;
68 }
69 
70 #ifdef CONFIG_SPL_BUILD
71 /*
72  * Routine: get_board_mem_timings
73  * Description: If we use SPL then there is no x-loader nor config header
74  * so we have to setup the DDR timings ourself on both banks.
75  */
76 void get_board_mem_timings(struct board_sdrc_timings *timings)
77 {
78 #if defined(CONFIG_SYS_BOARD_OMAP3_HA)
79 	/*
80 	 * Switch baseboard LED to red upon power-on
81 	 */
82 	MUX_OMAP3_HA();
83 
84 	/* Request a gpio before using it */
85 	gpio_request(111, "");
86 	/* Sets the gpio as output and its value to 1, switch LED to red */
87 	gpio_direction_output(111, 1);
88 #endif
89 
90 	if (tao3530_revision() < 3) {
91 		/* 256MB / Bank */
92 		timings->mcfg = MCFG(256 << 20, 14);	/* RAS-width 14 */
93 		timings->ctrla = HYNIX_V_ACTIMA_165;
94 		timings->ctrlb = HYNIX_V_ACTIMB_165;
95 	} else {
96 		/* 128MB / Bank */
97 		timings->mcfg = MCFG(128 << 20, 13);	/* RAS-width 13 */
98 		timings->ctrla = MICRON_V_ACTIMA_165;
99 		timings->ctrlb = MICRON_V_ACTIMB_165;
100 	}
101 
102 	timings->mr = MICRON_V_MR_165;
103 	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
104 }
105 #endif
106 
107 /*
108  * Routine: board_init
109  * Description: Early hardware init.
110  */
111 int board_init(void)
112 {
113 	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
114 	/* board id for Linux */
115 	gd->bd->bi_arch_number = MACH_TYPE_OMAP3_TAO3530;
116 	/* boot param addr */
117 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
118 
119 	return 0;
120 }
121 
122 /*
123  * Routine: misc_init_r
124  * Description: Configure board specific parts
125  */
126 int misc_init_r(void)
127 {
128 	struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
129 	struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
130 
131 	twl4030_power_init();
132 	twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
133 
134 	/* Configure GPIOs to output */
135 	/* GPIO23 */
136 	writel(~(GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
137 	writel(~(GPIO31 | GPIO30 | GPIO22 | GPIO21 |
138 		 GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
139 
140 	/* Set GPIOs */
141 	writel(GPIO10 | GPIO8 | GPIO2 | GPIO1,
142 	       &gpio6_base->setdataout);
143 	writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
144 	       GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
145 
146 	switch (tao3530_revision()) {
147 	case 0:
148 		puts("TAO-3530 REV Reserve 1\n");
149 		break;
150 	case 1:
151 		puts("TAO-3530 REV Reserve 2\n");
152 		break;
153 	case 2:
154 		puts("TAO-3530 REV Cx\n");
155 		break;
156 	case 3:
157 		puts("TAO-3530 REV Ax/Bx\n");
158 		break;
159 	default:
160 		puts("Unknown board revision\n");
161 	}
162 
163 	omap_die_id_display();
164 
165 	return 0;
166 }
167 
168 /*
169  * Routine: set_muxconf_regs
170  * Description: Setting up the configuration Mux registers specific to the
171  *		hardware. Many pins need to be moved from protect to primary
172  *		mode.
173  */
174 void set_muxconf_regs(void)
175 {
176 	MUX_TAO3530();
177 #if defined(CONFIG_SYS_BOARD_OMAP3_HA)
178 	MUX_OMAP3_HA();
179 #endif
180 }
181 
182 #if defined(CONFIG_MMC)
183 int board_mmc_init(bd_t *bis)
184 {
185 	omap_mmc_init(0, 0, 0, -1, -1);
186 
187 	return 0;
188 }
189 #endif
190 
191 #if defined(CONFIG_MMC)
192 void board_mmc_power_init(void)
193 {
194 	twl4030_power_mmc_init(0);
195 }
196 #endif
197 
198 #if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
199 /* Call usb_stop() before starting the kernel */
200 void show_boot_progress(int val)
201 {
202 	if (val == BOOTSTAGE_ID_RUN_OS)
203 		usb_stop();
204 }
205 
206 static struct omap_usbhs_board_data usbhs_bdata = {
207 	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
208 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
209 	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
210 };
211 
212 int ehci_hcd_init(int index, enum usb_init_type init,
213 		  struct ehci_hccr **hccr, struct ehci_hcor **hcor)
214 {
215 	return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
216 }
217 
218 int ehci_hcd_stop(int index)
219 {
220 	return omap_ehci_hcd_stop();
221 }
222 #endif /* CONFIG_USB_EHCI_HCD */
223