xref: /openbmc/u-boot/board/synopsys/emsdp/README (revision b3820ba9)
1================================================================================
2Useful notes on bulding and using of U-Boot on
3ARC EM Software Development Platform (AKA EMSDP)
4================================================================================
5
6   BOARD OVERVIEW
7
8   The DesignWare ARC EM Software Development Platform is FPGA-bases platform
9   for rapid software development on the ARC EM family of processors.
10
11   Since this board is based on FPGA it's possible to load and use different
12   versions of ARC EM CPUs. U-Boot is built to be run on the simplest
13   possible configuration which means the same one binary will work on more
14   advanced configurations as well.
15
16   The board has the following features useful for U-Boot:
17    * On-board 2-channel FTDI TTL-to-USB converter
18      - The first channel is used for serial debug port (which makes it possible
19        to use a serial connection on pretty much any host machine be it
20        Windows, Linux or Mac).
21        On Linux machine typucally FTDI serial port would be /dev/ttyUSB0.
22        There's no HW flow-control and baud-rate is 115200.
23
24      - The second channel is used for built-in Digilent USB JTAG probe.
25        That means no extra hardware is required to access ARC core from a
26        debugger on development host. Both proprietary MetaWare debugger and
27        open source OpenOCD + GDB client are supported.
28
29      - Also with help of this FTDI chip it is possible to reset entire
30        board with help of a special `rff-ftdi-reset` utility, see:
31        https://github.com/foss-for-synopsys-dwc-arc-processors/rff-ftdi-reset
32
33    * Micro SD-card slot
34      - U-Boot expects to see the very first partition on the card formatted as
35        FAT file-system and uses it for keeping its environment in `uboot.env`
36        file. Note uboot.env is not just a text file but it is auto-generated
37        file created by U-Boot on invocation of `saveenv` command.
38        It contains a checksum which makes this saved environment invalid in
39        case of maual modification.
40
41      - There might be more useful files on that first FAT partition like
42        user applications, data files etc.
43
44    * 256 KiB of "ROM"
45      - This so-called "ROM" is a part of FPGA image and even though it
46        might be unlocked for writes its initial content will be restored
47        on the next power-on.
48
49
50   BUILDING U-BOOT
51
52   1. Configure U-Boot:
53      ------------------------->8----------------------
54      make emsdp_defconfig
55      ------------------------->8----------------------
56
57   2. To build Elf file (for example to be used with host debugger via JTAG
58      connection to the target board):
59      ------------------------->8----------------------
60      make mdbtrick
61      ------------------------->8----------------------
62
63      This will produce `u-boot` Elf file.
64
65   3. To build binary image to be put in "ROM":
66      ------------------------->8----------------------
67      make u-boot.bin
68      ------------------------->8----------------------
69
70
71   EXECUTING U-BOOT
72
73   1. The EMSDP board is supposed to auto-start U-Boot image stored in ROM on
74      power-on. For that make sure VCCIO DIP-switches are all in "off" state.
75
76   2. Though it is possible to load U-Boot as a simple Elf file via JTAG right
77      in "ROM" and start it from the debugger. One important note here we first
78      need to enable writes into "ROM" by writing 1 to 0xf0001000.
79
80      2.1. In case of proprietary MetaWare debugger run:
81      ------------------------->8----------------------
82      mdb -dll=opxdarc.so -OK -preloadexec="eval *(int*)0xf0001000=0" u-boot
83      ------------------------->8----------------------
84