1 /* 2 * Copyright (C) 2012 Stefan Roese <sr@denx.de> 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 #include <common.h> 24 #include <spartan3.h> 25 #include <command.h> 26 #include <asm/gpio.h> 27 #include <asm/io.h> 28 #include <asm/arch/hardware.h> 29 #include <asm/arch/spr_misc.h> 30 #include <asm/arch/spr_ssp.h> 31 32 /* 33 * FPGA program pin configuration on X600: 34 * 35 * Only PROG and DONE are connected to GPIOs. INIT is not connected to the 36 * SoC at all. And CLOCK and DATA are connected to the SSP2 port. We use 37 * 16bit serial writes via this SSP port to write the data bits into the 38 * FPGA. 39 */ 40 #define CONFIG_SYS_FPGA_PROG 2 41 #define CONFIG_SYS_FPGA_DONE 3 42 43 /* 44 * Set the active-low FPGA reset signal. 45 */ 46 static void fpga_reset(int assert) 47 { 48 /* 49 * On x600 we have no means to toggle the FPGA reset signal 50 */ 51 debug("%s:%d: RESET (%d)\n", __func__, __LINE__, assert); 52 } 53 54 /* 55 * Set the FPGA's active-low SelectMap program line to the specified level 56 */ 57 static int fpga_pgm_fn(int assert, int flush, int cookie) 58 { 59 debug("%s:%d: FPGA PROG (%d)\n", __func__, __LINE__, assert); 60 61 gpio_set_value(CONFIG_SYS_FPGA_PROG, assert); 62 63 return assert; 64 } 65 66 /* 67 * Test the state of the active-low FPGA INIT line. Return 1 on INIT 68 * asserted (low). 69 */ 70 static int fpga_init_fn(int cookie) 71 { 72 static int state; 73 74 debug("%s:%d: init (state=%d)\n", __func__, __LINE__, state); 75 76 /* 77 * On x600, the FPGA INIT signal is not connected to the SoC. 78 * We can't read the INIT status. Let's return the "correct" 79 * INIT signal state generated via a local state-machine. 80 */ 81 if (++state == 1) { 82 return 1; 83 } else { 84 state = 0; 85 return 0; 86 } 87 } 88 89 /* 90 * Test the state of the active-high FPGA DONE pin 91 */ 92 static int fpga_done_fn(int cookie) 93 { 94 struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; 95 96 /* 97 * Wait for Tx-FIFO to become empty before looking for DONE 98 */ 99 while (!(readl(&ssp->sspsr) & SSPSR_TFE)) 100 ; 101 102 if (gpio_get_value(CONFIG_SYS_FPGA_DONE)) 103 return 1; 104 else 105 return 0; 106 } 107 108 /* 109 * FPGA pre-configuration function. Just make sure that 110 * FPGA reset is asserted to keep the FPGA from starting up after 111 * configuration. 112 */ 113 static int fpga_pre_config_fn(int cookie) 114 { 115 debug("%s:%d: FPGA pre-configuration\n", __func__, __LINE__); 116 fpga_reset(true); 117 118 return 0; 119 } 120 121 /* 122 * FPGA post configuration function. Blip the FPGA reset line and then see if 123 * the FPGA appears to be running. 124 */ 125 static int fpga_post_config_fn(int cookie) 126 { 127 int rc = 0; 128 129 debug("%s:%d: FPGA post configuration\n", __func__, __LINE__); 130 131 fpga_reset(true); 132 udelay(100); 133 fpga_reset(false); 134 udelay(100); 135 136 return rc; 137 } 138 139 static int fpga_clk_fn(int assert_clk, int flush, int cookie) 140 { 141 /* 142 * No dedicated clock signal on x600 (data & clock generated) 143 * in SSP interface. So we don't have to do anything here. 144 */ 145 return assert_clk; 146 } 147 148 static int fpga_wr_fn(int assert_write, int flush, int cookie) 149 { 150 struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; 151 static int count; 152 static u16 data; 153 154 /* 155 * First collect 16 bits of data 156 */ 157 data = data << 1; 158 if (assert_write) 159 data |= 1; 160 161 /* 162 * If 16 bits are not available, return for more bits 163 */ 164 count++; 165 if (count != 16) 166 return assert_write; 167 168 count = 0; 169 170 /* 171 * Wait for Tx-FIFO to become ready 172 */ 173 while (!(readl(&ssp->sspsr) & SSPSR_TNF)) 174 ; 175 176 /* Send 16 bits to FPGA via SSP bus */ 177 writel(data, &ssp->sspdr); 178 179 return assert_write; 180 } 181 182 static Xilinx_Spartan3_Slave_Serial_fns x600_fpga_fns = { 183 fpga_pre_config_fn, 184 fpga_pgm_fn, 185 fpga_clk_fn, 186 fpga_init_fn, 187 fpga_done_fn, 188 fpga_wr_fn, 189 fpga_post_config_fn, 190 }; 191 192 static Xilinx_desc fpga[CONFIG_FPGA_COUNT] = { 193 XILINX_XC3S1200E_DESC(slave_serial, &x600_fpga_fns, 0) 194 }; 195 196 /* 197 * Initialize the SelectMap interface. We assume that the mode and the 198 * initial state of all of the port pins have already been set! 199 */ 200 static void fpga_serialslave_init(void) 201 { 202 debug("%s:%d: Initialize serial slave interface\n", __func__, __LINE__); 203 fpga_pgm_fn(false, false, 0); /* make sure program pin is inactive */ 204 } 205 206 static int expi_setup(int freq) 207 { 208 struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; 209 int pll2_m, pll2_n, pll2_p, expi_x, expi_y; 210 211 pll2_m = (freq * 2) / 1000; 212 pll2_n = 15; 213 pll2_p = 1; 214 expi_x = 1; 215 expi_y = 2; 216 217 /* 218 * Disable reset, Low compression, Disable retiming, Enable Expi, 219 * Enable soft reset, DMA, PLL2, Internal 220 */ 221 writel(EXPI_CLK_CFG_LOW_COMPR | EXPI_CLK_CFG_CLK_EN | EXPI_CLK_CFG_RST | 222 EXPI_CLK_SYNT_EN | EXPI_CLK_CFG_SEL_PLL2 | 223 EXPI_CLK_CFG_INT_CLK_EN | (expi_y << 16) | (expi_x << 24), 224 &misc->expi_clk_cfg); 225 226 /* 227 * 6 uA, Internal feedback, 1st order, Non-dithered, Sample Parameters, 228 * Enable PLL2, Disable reset 229 */ 230 writel((pll2_m << 24) | (pll2_p << 8) | (pll2_n), &misc->pll2_frq); 231 writel(PLL2_CNTL_6UA | PLL2_CNTL_SAMPLE | PLL2_CNTL_ENABLE | 232 PLL2_CNTL_RESETN | PLL2_CNTL_LOCK, &misc->pll2_cntl); 233 234 /* 235 * Disable soft reset 236 */ 237 clrbits_le32(&misc->expi_clk_cfg, EXPI_CLK_CFG_RST); 238 239 return 0; 240 } 241 242 /* 243 * Initialize the fpga 244 */ 245 int x600_init_fpga(void) 246 { 247 struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; 248 struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; 249 250 /* Enable SSP2 clock */ 251 writel(readl(&misc->periph1_clken) | MISC_SSP2ENB | MISC_GPIO4ENB, 252 &misc->periph1_clken); 253 254 /* Set EXPI clock to 45 MHz */ 255 expi_setup(45000); 256 257 /* Configure GPIO directions */ 258 gpio_direction_output(CONFIG_SYS_FPGA_PROG, 0); 259 gpio_direction_input(CONFIG_SYS_FPGA_DONE); 260 261 writel(SSPCR0_DSS_16BITS, &ssp->sspcr0); 262 writel(SSPCR1_SSE, &ssp->sspcr1); 263 264 /* 265 * Set lowest prescale divisor value (CPSDVSR) of 2 for max download 266 * speed. 267 * 268 * Actual data clock rate is: 80MHz / (CPSDVSR * (SCR + 1)) 269 * With CPSDVSR at 2 and SCR at 0, the maximume clock rate is 40MHz. 270 */ 271 writel(2, &ssp->sspcpsr); 272 273 fpga_init(); 274 fpga_serialslave_init(); 275 276 debug("%s:%d: Adding fpga 0\n", __func__, __LINE__); 277 fpga_add(fpga_xilinx, &fpga[0]); 278 279 return 0; 280 } 281