1 /* 2 * Copyright (C) 2015 Stefan Roese <sr@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <i2c.h> 9 #include <miiphy.h> 10 #include <netdev.h> 11 #include <asm/io.h> 12 #include <asm/arch/cpu.h> 13 #include <asm/arch/soc.h> 14 15 #include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h" 16 #include <../serdes/a38x/high_speed_env_spec.h> 17 18 DECLARE_GLOBAL_DATA_PTR; 19 20 #define ETH_PHY_CTRL_REG 0 21 #define ETH_PHY_CTRL_POWER_DOWN_BIT 11 22 #define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT) 23 24 /* 25 * Those values and defines are taken from the Marvell U-Boot version 26 * "u-boot-2013.01-15t1-clearfog" 27 */ 28 #define BOARD_GPP_OUT_ENA_LOW 0xffffffff 29 #define BOARD_GPP_OUT_ENA_MID 0xffffffff 30 31 #define BOARD_GPP_OUT_VAL_LOW 0x0 32 #define BOARD_GPP_OUT_VAL_MID 0x0 33 #define BOARD_GPP_POL_LOW 0x0 34 #define BOARD_GPP_POL_MID 0x0 35 36 /* IO expander on Marvell GP board includes e.g. fan enabling */ 37 struct marvell_io_exp { 38 u8 chip; 39 u8 addr; 40 u8 val; 41 }; 42 43 static struct marvell_io_exp io_exp[] = { 44 { 0x20, 2, 0x40 }, /* Deassert both mini pcie reset signals */ 45 { 0x20, 6, 0xf9 }, 46 { 0x20, 2, 0x46 }, /* rst signals and ena USB3 current limiter */ 47 { 0x20, 6, 0xb9 }, 48 { 0x20, 3, 0x00 }, /* Set SFP_TX_DIS to zero */ 49 { 0x20, 7, 0xbf }, /* Drive SFP_TX_DIS to zero */ 50 }; 51 52 static struct serdes_map board_serdes_map[] = { 53 {SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 54 {SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 55 {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, 56 {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 57 {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, 58 {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 59 }; 60 61 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) 62 { 63 *serdes_map_array = board_serdes_map; 64 *count = ARRAY_SIZE(board_serdes_map); 65 return 0; 66 } 67 68 /* 69 * Define the DDR layout / topology here in the board file. This will 70 * be used by the DDR3 init code in the SPL U-Boot version to configure 71 * the DDR3 controller. 72 */ 73 static struct hws_topology_map board_topology_map = { 74 0x1, /* active interfaces */ 75 /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */ 76 { { { {0x1, 0, 0, 0}, 77 {0x1, 0, 0, 0}, 78 {0x1, 0, 0, 0}, 79 {0x1, 0, 0, 0}, 80 {0x1, 0, 0, 0} }, 81 SPEED_BIN_DDR_1600K, /* speed_bin */ 82 BUS_WIDTH_16, /* memory_width */ 83 MEM_4G, /* mem_size */ 84 DDR_FREQ_800, /* frequency */ 85 0, 0, /* cas_wl cas_l */ 86 HWS_TEMP_LOW, /* temperature */ 87 HWS_TIM_DEFAULT} }, /* timing */ 88 5, /* Num Of Bus Per Interface*/ 89 BUS_MASK_32BIT /* Busses mask */ 90 }; 91 92 struct hws_topology_map *ddr3_get_topology_map(void) 93 { 94 /* Return the board topology as defined in the board code */ 95 return &board_topology_map; 96 } 97 98 int board_early_init_f(void) 99 { 100 /* Configure MPP */ 101 writel(0x11111111, MVEBU_MPP_BASE + 0x00); 102 writel(0x11111111, MVEBU_MPP_BASE + 0x04); 103 writel(0x10400011, MVEBU_MPP_BASE + 0x08); 104 writel(0x22043333, MVEBU_MPP_BASE + 0x0c); 105 writel(0x44400002, MVEBU_MPP_BASE + 0x10); 106 writel(0x41144004, MVEBU_MPP_BASE + 0x14); 107 writel(0x40333333, MVEBU_MPP_BASE + 0x18); 108 writel(0x00004444, MVEBU_MPP_BASE + 0x1c); 109 110 /* Set GPP Out value */ 111 writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00); 112 writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); 113 114 /* Set GPP Polarity */ 115 writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c); 116 writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); 117 118 /* Set GPP Out Enable */ 119 writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04); 120 writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); 121 122 return 0; 123 } 124 125 int board_init(void) 126 { 127 int i; 128 129 /* Address of boot parameters */ 130 gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; 131 132 /* Toggle GPIO41 to reset onboard switch and phy */ 133 clrbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9)); 134 clrbits_le32(MVEBU_GPIO1_BASE + 0x4, BIT(9)); 135 /* GPIO 19 on ClearFog rev 2.1 controls the uSOM onboard phy reset */ 136 clrbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19)); 137 clrbits_le32(MVEBU_GPIO0_BASE + 0x4, BIT(19)); 138 mdelay(1); 139 setbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9)); 140 setbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19)); 141 mdelay(10); 142 143 /* Init I2C IO expanders */ 144 for (i = 0; i < ARRAY_SIZE(io_exp); i++) 145 i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1); 146 147 return 0; 148 } 149 150 int checkboard(void) 151 { 152 puts("Board: SolidRun ClearFog\n"); 153 154 return 0; 155 } 156 157 int board_eth_init(bd_t *bis) 158 { 159 cpu_eth_init(bis); /* Built in controller(s) come first */ 160 return pci_eth_init(bis); 161 } 162