1 /* 2 * board.c 3 * 4 * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <asm/arch/cpu.h> 11 #include <asm/arch/hardware.h> 12 #include <asm/arch/ddr_defs.h> 13 #include <asm/arch/clock.h> 14 #include <asm/arch/sys_proto.h> 15 #include <i2c.h> 16 #include <phy.h> 17 #include <cpsw.h> 18 #include "board.h" 19 20 DECLARE_GLOBAL_DATA_PTR; 21 22 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 23 24 #if defined(CONFIG_SPL_BUILD) 25 26 /* DDR3 RAM timings */ 27 static const struct ddr_data ddr3_data = { 28 .datardsratio0 = MT41K128MJT187E_RD_DQS, 29 .datawdsratio0 = MT41K128MJT187E_WR_DQS, 30 .datafwsratio0 = MT41K128MJT187E_PHY_FIFO_WE, 31 .datawrsratio0 = MT41K128MJT187E_PHY_WR_DATA, 32 }; 33 34 static const struct cmd_control ddr3_cmd_ctrl_data = { 35 .cmd0csratio = MT41K128MJT187E_RATIO, 36 .cmd0iclkout = MT41K128MJT187E_INVERT_CLKOUT, 37 .cmd1csratio = MT41K128MJT187E_RATIO, 38 .cmd1iclkout = MT41K128MJT187E_INVERT_CLKOUT, 39 .cmd2csratio = MT41K128MJT187E_RATIO, 40 .cmd2iclkout = MT41K128MJT187E_INVERT_CLKOUT, 41 }; 42 43 static struct emif_regs ddr3_emif_reg_data = { 44 .sdram_config = MT41K128MJT187E_EMIF_SDCFG, 45 .ref_ctrl = MT41K128MJT187E_EMIF_SDREF, 46 .sdram_tim1 = MT41K128MJT187E_EMIF_TIM1, 47 .sdram_tim2 = MT41K128MJT187E_EMIF_TIM2, 48 .sdram_tim3 = MT41K128MJT187E_EMIF_TIM3, 49 .zq_config = MT41K128MJT187E_ZQ_CFG, 50 .emif_ddr_phy_ctlr_1 = MT41K128MJT187E_EMIF_READ_LATENCY | 51 PHY_EN_DYN_PWRDN, 52 }; 53 54 const struct ctrl_ioregs ddr3_ioregs = { 55 .cm0ioctl = MT41K128MJT187E_IOCTRL_VALUE, 56 .cm1ioctl = MT41K128MJT187E_IOCTRL_VALUE, 57 .cm2ioctl = MT41K128MJT187E_IOCTRL_VALUE, 58 .dt0ioctl = MT41K128MJT187E_IOCTRL_VALUE, 59 .dt1ioctl = MT41K128MJT187E_IOCTRL_VALUE, 60 }; 61 62 #ifdef CONFIG_SPL_OS_BOOT 63 int spl_start_uboot(void) 64 { 65 /* break into full u-boot on 'c' */ 66 return serial_tstc() && serial_getc() == 'c'; 67 } 68 #endif 69 70 #define OSC (V_OSCK/1000000) 71 const struct dpll_params dpll_ddr_266 = { 72 266, OSC-1, 1, -1, -1, -1, -1}; 73 const struct dpll_params dpll_ddr_303 = { 74 303, OSC-1, 1, -1, -1, -1, -1}; 75 const struct dpll_params dpll_ddr_400 = { 76 400, OSC-1, 1, -1, -1, -1, -1}; 77 78 void am33xx_spl_board_init(void) 79 { 80 /* 81 * The pengwyn board uses the TPS650250 PMIC without I2C 82 * interface and will output the following fixed voltages: 83 * DCDC1=3V3 (IO) DCDC2=1V5 (DDR) DCDC3=1V26 (Vmpu) 84 * VLDO1=1V8 (IO) VLDO2=1V8(IO) 85 * Vcore=1V1 is fixed, generated by TPS62231 86 */ 87 88 /* Get the frequency */ 89 dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); 90 91 /* Set CORE Frequencies to OPP100 */ 92 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); 93 94 /* 720MHz cpu, this might change on newer board revisions */ 95 dpll_mpu_opp100.m = MPUPLL_M_720; 96 do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100); 97 } 98 99 const struct dpll_params *get_dpll_ddr_params(void) 100 { 101 /* future configs can return other clock settings */ 102 return &dpll_ddr_303; 103 } 104 105 void set_uart_mux_conf(void) 106 { 107 enable_uart0_pin_mux(); 108 } 109 110 void set_mux_conf_regs(void) 111 { 112 enable_board_pin_mux(); 113 } 114 115 void sdram_init(void) 116 { 117 config_ddr(303, &ddr3_ioregs, &ddr3_data, 118 &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0); 119 } 120 #endif /* if CONFIG_SPL_BUILD */ 121 122 /* 123 * Basic board specific setup. Pinmux has been handled already. 124 */ 125 int board_init(void) 126 { 127 i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); 128 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 129 gpmc_init(); 130 return 0; 131 } 132 133 #ifdef CONFIG_DRIVER_TI_CPSW 134 static void cpsw_control(int enabled) 135 { 136 /* VTP can be added here */ 137 return; 138 } 139 140 static struct cpsw_slave_data cpsw_slaves[] = { 141 { 142 .slave_reg_ofs = 0x208, 143 .sliver_reg_ofs = 0xd80, 144 .phy_addr = 1, 145 .phy_if = PHY_INTERFACE_MODE_MII, 146 }, 147 }; 148 149 static struct cpsw_platform_data cpsw_data = { 150 .mdio_base = CPSW_MDIO_BASE, 151 .cpsw_base = CPSW_BASE, 152 .mdio_div = 0xff, 153 .channels = 8, 154 .cpdma_reg_ofs = 0x800, 155 .slaves = 1, 156 .slave_data = cpsw_slaves, 157 .ale_reg_ofs = 0xd00, 158 .ale_entries = 1024, 159 .host_port_reg_ofs = 0x108, 160 .hw_stats_reg_ofs = 0x900, 161 .bd_ram_ofs = 0x2000, 162 .mac_control = (1 << 5), 163 .control = cpsw_control, 164 .host_port_num = 0, 165 .version = CPSW_CTRL_VERSION_2, 166 }; 167 168 int board_eth_init(bd_t *bis) 169 { 170 int rv, n = 0; 171 uint8_t mac_addr[6]; 172 uint32_t mac_hi, mac_lo; 173 174 if (!eth_getenv_enetaddr("ethaddr", mac_addr)) { 175 printf("<ethaddr> not set. Reading from E-fuse\n"); 176 /* try reading mac address from efuse */ 177 mac_lo = readl(&cdev->macid0l); 178 mac_hi = readl(&cdev->macid0h); 179 mac_addr[0] = mac_hi & 0xFF; 180 mac_addr[1] = (mac_hi & 0xFF00) >> 8; 181 mac_addr[2] = (mac_hi & 0xFF0000) >> 16; 182 mac_addr[3] = (mac_hi & 0xFF000000) >> 24; 183 mac_addr[4] = mac_lo & 0xFF; 184 mac_addr[5] = (mac_lo & 0xFF00) >> 8; 185 186 if (is_valid_ethaddr(mac_addr)) 187 eth_setenv_enetaddr("ethaddr", mac_addr); 188 else 189 return n; 190 } 191 192 writel(MII_MODE_ENABLE, &cdev->miisel); 193 194 rv = cpsw_register(&cpsw_data); 195 if (rv < 0) 196 printf("Error %d registering CPSW switch\n", rv); 197 else 198 n += rv; 199 return n; 200 } 201 #endif /* if CONFIG_DRIVER_TI_CPSW */ 202