1 /* 2 * Board functions for TI AM335X based pxm2 board 3 * (C) Copyright 2013 Siemens Schweiz AG 4 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * 6 * Based on: 7 * u-boot:/board/ti/am335x/board.c 8 * 9 * Board functions for TI AM335X based boards 10 * 11 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ 12 * 13 * SPDX-License-Identifier: GPL-2.0+ 14 */ 15 16 #include <common.h> 17 #include <errno.h> 18 #include <spl.h> 19 #include <asm/arch/cpu.h> 20 #include <asm/arch/hardware.h> 21 #include <asm/arch/omap.h> 22 #include <asm/arch/ddr_defs.h> 23 #include <asm/arch/clock.h> 24 #include <asm/arch/gpio.h> 25 #include <asm/arch/mmc_host_def.h> 26 #include <asm/arch/sys_proto.h> 27 #include "../../../drivers/video/da8xx-fb.h" 28 #include <asm/io.h> 29 #include <asm/emif.h> 30 #include <asm/gpio.h> 31 #include <i2c.h> 32 #include <miiphy.h> 33 #include <cpsw.h> 34 #include <watchdog.h> 35 #include "board.h" 36 #include "../common/factoryset.h" 37 #include "pmic.h" 38 #include <nand.h> 39 #include <bmp_layout.h> 40 41 DECLARE_GLOBAL_DATA_PTR; 42 43 #ifdef CONFIG_SPL_BUILD 44 static void board_init_ddr(void) 45 { 46 struct emif_regs pxm2_ddr3_emif_reg_data = { 47 .sdram_config = 0x41805332, 48 .sdram_tim1 = 0x666b3c9, 49 .sdram_tim2 = 0x243631ca, 50 .sdram_tim3 = 0x33f, 51 .emif_ddr_phy_ctlr_1 = 0x100005, 52 .zq_config = 0, 53 .ref_ctrl = 0x81a, 54 }; 55 56 struct ddr_data pxm2_ddr3_data = { 57 .datardsratio0 = 0x81204812, 58 .datawdsratio0 = 0, 59 .datafwsratio0 = 0x8020080, 60 .datawrsratio0 = 0x4010040, 61 }; 62 63 struct cmd_control pxm2_ddr3_cmd_ctrl_data = { 64 .cmd0csratio = 0x80, 65 .cmd0iclkout = 0, 66 .cmd1csratio = 0x80, 67 .cmd1iclkout = 0, 68 .cmd2csratio = 0x80, 69 .cmd2iclkout = 0, 70 }; 71 72 const struct ctrl_ioregs ioregs = { 73 .cm0ioctl = DXR2_IOCTRL_VAL, 74 .cm1ioctl = DXR2_IOCTRL_VAL, 75 .cm2ioctl = DXR2_IOCTRL_VAL, 76 .dt0ioctl = DXR2_IOCTRL_VAL, 77 .dt1ioctl = DXR2_IOCTRL_VAL, 78 }; 79 80 config_ddr(DDR_PLL_FREQ, &ioregs, &pxm2_ddr3_data, 81 &pxm2_ddr3_cmd_ctrl_data, &pxm2_ddr3_emif_reg_data, 0); 82 } 83 84 /* 85 * voltage switching for MPU frequency switching. 86 * @module = mpu - 0, core - 1 87 * @vddx_op_vol_sel = vdd voltage to set 88 */ 89 90 #define MPU 0 91 #define CORE 1 92 93 int voltage_update(unsigned int module, unsigned char vddx_op_vol_sel) 94 { 95 uchar buf[4]; 96 unsigned int reg_offset; 97 98 if (module == MPU) 99 reg_offset = PMIC_VDD1_OP_REG; 100 else 101 reg_offset = PMIC_VDD2_OP_REG; 102 103 /* Select VDDx OP */ 104 if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 105 return 1; 106 107 buf[0] &= ~PMIC_OP_REG_CMD_MASK; 108 109 if (i2c_write(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 110 return 1; 111 112 /* Configure VDDx OP Voltage */ 113 if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 114 return 1; 115 116 buf[0] &= ~PMIC_OP_REG_SEL_MASK; 117 buf[0] |= vddx_op_vol_sel; 118 119 if (i2c_write(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 120 return 1; 121 122 if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 123 return 1; 124 125 if ((buf[0] & PMIC_OP_REG_SEL_MASK) != vddx_op_vol_sel) 126 return 1; 127 128 return 0; 129 } 130 131 #define OSC (V_OSCK/1000000) 132 133 const struct dpll_params dpll_mpu_pxm2 = { 134 720, OSC-1, 1, -1, -1, -1, -1}; 135 136 void spl_siemens_board_init(void) 137 { 138 uchar buf[4]; 139 /* 140 * pxm2 PMIC code. All boards currently want an MPU voltage 141 * of 1.2625V and CORE voltage of 1.1375V to operate at 142 * 720MHz. 143 */ 144 if (i2c_probe(PMIC_CTRL_I2C_ADDR)) 145 return; 146 147 /* VDD1/2 voltage selection register access by control i/f */ 148 if (i2c_read(PMIC_CTRL_I2C_ADDR, PMIC_DEVCTRL_REG, 1, buf, 1)) 149 return; 150 151 buf[0] |= PMIC_DEVCTRL_REG_SR_CTL_I2C_SEL_CTL_I2C; 152 153 if (i2c_write(PMIC_CTRL_I2C_ADDR, PMIC_DEVCTRL_REG, 1, buf, 1)) 154 return; 155 156 /* Frequency switching for OPP 120 */ 157 if (voltage_update(MPU, PMIC_OP_REG_SEL_1_2_6) || 158 voltage_update(CORE, PMIC_OP_REG_SEL_1_1_3)) { 159 printf("voltage update failed\n"); 160 } 161 } 162 #endif /* if def CONFIG_SPL_BUILD */ 163 164 int read_eeprom(void) 165 { 166 /* nothing ToDo here for this board */ 167 168 return 0; 169 } 170 171 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 172 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 173 static void cpsw_control(int enabled) 174 { 175 /* VTP can be added here */ 176 177 return; 178 } 179 180 static struct cpsw_slave_data cpsw_slaves[] = { 181 { 182 .slave_reg_ofs = 0x208, 183 .sliver_reg_ofs = 0xd80, 184 .phy_id = 0, 185 .phy_if = PHY_INTERFACE_MODE_RMII, 186 }, 187 { 188 .slave_reg_ofs = 0x308, 189 .sliver_reg_ofs = 0xdc0, 190 .phy_id = 1, 191 .phy_if = PHY_INTERFACE_MODE_RMII, 192 }, 193 }; 194 195 static struct cpsw_platform_data cpsw_data = { 196 .mdio_base = CPSW_MDIO_BASE, 197 .cpsw_base = CPSW_BASE, 198 .mdio_div = 0xff, 199 .channels = 4, 200 .cpdma_reg_ofs = 0x800, 201 .slaves = 1, 202 .slave_data = cpsw_slaves, 203 .ale_reg_ofs = 0xd00, 204 .ale_entries = 1024, 205 .host_port_reg_ofs = 0x108, 206 .hw_stats_reg_ofs = 0x900, 207 .bd_ram_ofs = 0x2000, 208 .mac_control = (1 << 5), 209 .control = cpsw_control, 210 .host_port_num = 0, 211 .version = CPSW_CTRL_VERSION_2, 212 }; 213 #endif /* #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) */ 214 215 #if defined(CONFIG_DRIVER_TI_CPSW) || \ 216 (defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) 217 int board_eth_init(bd_t *bis) 218 { 219 int n = 0; 220 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 221 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 222 struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 223 #ifdef CONFIG_FACTORYSET 224 int rv; 225 if (!is_valid_ether_addr(factory_dat.mac)) 226 printf("Error: no valid mac address\n"); 227 else 228 eth_setenv_enetaddr("ethaddr", factory_dat.mac); 229 #endif /* #ifdef CONFIG_FACTORYSET */ 230 231 /* Set rgmii mode and enable rmii clock to be sourced from chip */ 232 writel(RGMII_MODE_ENABLE , &cdev->miisel); 233 234 rv = cpsw_register(&cpsw_data); 235 if (rv < 0) 236 printf("Error %d registering CPSW switch\n", rv); 237 else 238 n += rv; 239 #endif 240 return n; 241 } 242 #endif /* #if defined(CONFIG_DRIVER_TI_CPSW) */ 243 244 #if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) 245 static struct da8xx_panel lcd_panels[] = { 246 /* AUO G156XW01 V1 */ 247 [0] = { 248 .name = "AUO_G156XW01_V1", 249 .width = 1376, 250 .height = 768, 251 .hfp = 14, 252 .hbp = 64, 253 .hsw = 56, 254 .vfp = 1, 255 .vbp = 28, 256 .vsw = 3, 257 .pxl_clk = 60000000, 258 .invert_pxl_clk = 0, 259 }, 260 /* AUO B101EVN06 V0 */ 261 [1] = { 262 .name = "AUO_B101EVN06_V0", 263 .width = 1280, 264 .height = 800, 265 .hfp = 52, 266 .hbp = 84, 267 .hsw = 36, 268 .vfp = 3, 269 .vbp = 14, 270 .vsw = 6, 271 .pxl_clk = 60000000, 272 .invert_pxl_clk = 0, 273 }, 274 /* 275 * Settings from factoryset 276 * stored in EEPROM 277 */ 278 [2] = { 279 .name = "factoryset", 280 .width = 0, 281 .height = 0, 282 .hfp = 0, 283 .hbp = 0, 284 .hsw = 0, 285 .vfp = 0, 286 .vbp = 0, 287 .vsw = 0, 288 .pxl_clk = 60000000, 289 .invert_pxl_clk = 0, 290 }, 291 }; 292 293 static const struct display_panel disp_panel = { 294 WVGA, 295 32, 296 16, 297 COLOR_ACTIVE, 298 }; 299 300 static const struct lcd_ctrl_config lcd_cfg = { 301 &disp_panel, 302 .ac_bias = 255, 303 .ac_bias_intrpt = 0, 304 .dma_burst_sz = 16, 305 .bpp = 32, 306 .fdd = 0x80, 307 .tft_alt_mode = 0, 308 .stn_565_mode = 0, 309 .mono_8bit_mode = 0, 310 .invert_line_clock = 1, 311 .invert_frm_clock = 1, 312 .sync_edge = 0, 313 .sync_ctrl = 1, 314 .raster_order = 0, 315 }; 316 317 static int set_gpio(int gpio, int state) 318 { 319 gpio_request(gpio, "temp"); 320 gpio_direction_output(gpio, state); 321 gpio_set_value(gpio, state); 322 gpio_free(gpio); 323 return 0; 324 } 325 326 static int enable_backlight(void) 327 { 328 set_gpio(BOARD_LCD_POWER, 1); 329 set_gpio(BOARD_BACK_LIGHT, 1); 330 set_gpio(BOARD_TOUCH_POWER, 1); 331 return 0; 332 } 333 334 static int enable_pwm(void) 335 { 336 struct pwmss_regs *pwmss = (struct pwmss_regs *)PWMSS0_BASE; 337 struct pwmss_ecap_regs *ecap; 338 int ticks = PWM_TICKS; 339 int duty = PWM_DUTY; 340 341 ecap = (struct pwmss_ecap_regs *)AM33XX_ECAP0_BASE; 342 /* enable clock */ 343 setbits_le32(&pwmss->clkconfig, ECAP_CLK_EN); 344 /* TimeStam Counter register */ 345 writel(0xdb9, &ecap->tsctr); 346 /* config period */ 347 writel(ticks - 1, &ecap->cap3); 348 writel(ticks - 1, &ecap->cap1); 349 setbits_le16(&ecap->ecctl2, 350 (ECTRL2_MDSL_ECAP | ECTRL2_SYNCOSEL_MASK | 0xd0)); 351 /* config duty */ 352 writel(duty, &ecap->cap2); 353 writel(duty, &ecap->cap4); 354 /* start */ 355 setbits_le16(&ecap->ecctl2, ECTRL2_CTRSTP_FREERUN); 356 return 0; 357 } 358 359 static struct dpll_regs dpll_lcd_regs = { 360 .cm_clkmode_dpll = CM_WKUP + 0x98, 361 .cm_idlest_dpll = CM_WKUP + 0x48, 362 .cm_clksel_dpll = CM_WKUP + 0x54, 363 }; 364 365 /* no console on this board */ 366 int board_cfb_skip(void) 367 { 368 return 1; 369 } 370 371 #define PLL_GET_M(v) ((v >> 8) & 0x7ff) 372 #define PLL_GET_N(v) (v & 0x7f) 373 374 static int get_clk(struct dpll_regs *dpll_regs) 375 { 376 unsigned int val; 377 unsigned int m, n; 378 int f = 0; 379 380 val = readl(dpll_regs->cm_clksel_dpll); 381 m = PLL_GET_M(val); 382 n = PLL_GET_N(val); 383 f = (m * V_OSCK) / n; 384 385 return f; 386 }; 387 388 int clk_get(int clk) 389 { 390 return get_clk(&dpll_lcd_regs); 391 }; 392 393 static int conf_disp_pll(int m, int n) 394 { 395 struct cm_perpll *cmper = (struct cm_perpll *)CM_PER; 396 struct cm_dpll *cmdpll = (struct cm_dpll *)CM_DPLL; 397 struct dpll_params dpll_lcd = {m, n, -1, -1, -1, -1, -1}; 398 399 u32 *const clk_domains[] = { 400 &cmper->lcdclkctrl, 401 0 402 }; 403 u32 *const clk_modules_explicit_en[] = { 404 &cmper->lcdclkctrl, 405 &cmper->lcdcclkstctrl, 406 &cmper->epwmss0clkctrl, 407 0 408 }; 409 do_enable_clocks(clk_domains, clk_modules_explicit_en, 1); 410 writel(0x0, &cmdpll->clklcdcpixelclk); 411 412 do_setup_dpll(&dpll_lcd_regs, &dpll_lcd); 413 414 return 0; 415 } 416 417 static int board_video_init(void) 418 { 419 conf_disp_pll(24, 1); 420 if (factory_dat.pxm50) 421 da8xx_video_init(&lcd_panels[0], &lcd_cfg, lcd_cfg.bpp); 422 else 423 da8xx_video_init(&lcd_panels[1], &lcd_cfg, lcd_cfg.bpp); 424 425 enable_pwm(); 426 enable_backlight(); 427 428 return 0; 429 } 430 #endif 431 #include "../common/board.c" 432