1 /* 2 * Board functions for TI AM335X based pxm2 board 3 * (C) Copyright 2013 Siemens Schweiz AG 4 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * 6 * Based on: 7 * u-boot:/board/ti/am335x/board.c 8 * 9 * Board functions for TI AM335X based boards 10 * 11 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ 12 * 13 * SPDX-License-Identifier: GPL-2.0+ 14 */ 15 16 #include <common.h> 17 #include <errno.h> 18 #include <spl.h> 19 #include <asm/arch/cpu.h> 20 #include <asm/arch/hardware.h> 21 #include <asm/arch/omap.h> 22 #include <asm/arch/ddr_defs.h> 23 #include <asm/arch/clock.h> 24 #include <asm/arch/gpio.h> 25 #include <asm/arch/mmc_host_def.h> 26 #include <asm/arch/sys_proto.h> 27 #include "../../../drivers/video/da8xx-fb.h" 28 #include <asm/io.h> 29 #include <asm/emif.h> 30 #include <asm/gpio.h> 31 #include <i2c.h> 32 #include <miiphy.h> 33 #include <cpsw.h> 34 #include <watchdog.h> 35 #include "board.h" 36 #include "../common/factoryset.h" 37 #include "pmic.h" 38 #include <nand.h> 39 #include <bmp_layout.h> 40 41 DECLARE_GLOBAL_DATA_PTR; 42 43 #ifdef CONFIG_SPL_BUILD 44 static void board_init_ddr(void) 45 { 46 struct emif_regs pxm2_ddr3_emif_reg_data = { 47 .sdram_config = 0x41805332, 48 .sdram_tim1 = 0x666b3c9, 49 .sdram_tim2 = 0x243631ca, 50 .sdram_tim3 = 0x33f, 51 .emif_ddr_phy_ctlr_1 = 0x100005, 52 .zq_config = 0, 53 .ref_ctrl = 0x81a, 54 }; 55 56 struct ddr_data pxm2_ddr3_data = { 57 .datardsratio0 = 0x81204812, 58 .datawdsratio0 = 0, 59 .datafwsratio0 = 0x8020080, 60 .datawrsratio0 = 0x4010040, 61 .datauserank0delay = 1, 62 .datadldiff0 = PHY_DLL_LOCK_DIFF, 63 }; 64 65 struct cmd_control pxm2_ddr3_cmd_ctrl_data = { 66 .cmd0csratio = 0x80, 67 .cmd0dldiff = 0, 68 .cmd0iclkout = 0, 69 .cmd1csratio = 0x80, 70 .cmd1dldiff = 0, 71 .cmd1iclkout = 0, 72 .cmd2csratio = 0x80, 73 .cmd2dldiff = 0, 74 .cmd2iclkout = 0, 75 }; 76 77 config_ddr(DDR_PLL_FREQ, DXR2_IOCTRL_VAL, &pxm2_ddr3_data, 78 &pxm2_ddr3_cmd_ctrl_data, &pxm2_ddr3_emif_reg_data, 0); 79 } 80 81 /* 82 * voltage switching for MPU frequency switching. 83 * @module = mpu - 0, core - 1 84 * @vddx_op_vol_sel = vdd voltage to set 85 */ 86 87 #define MPU 0 88 #define CORE 1 89 90 int voltage_update(unsigned int module, unsigned char vddx_op_vol_sel) 91 { 92 uchar buf[4]; 93 unsigned int reg_offset; 94 95 if (module == MPU) 96 reg_offset = PMIC_VDD1_OP_REG; 97 else 98 reg_offset = PMIC_VDD2_OP_REG; 99 100 /* Select VDDx OP */ 101 if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 102 return 1; 103 104 buf[0] &= ~PMIC_OP_REG_CMD_MASK; 105 106 if (i2c_write(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 107 return 1; 108 109 /* Configure VDDx OP Voltage */ 110 if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 111 return 1; 112 113 buf[0] &= ~PMIC_OP_REG_SEL_MASK; 114 buf[0] |= vddx_op_vol_sel; 115 116 if (i2c_write(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 117 return 1; 118 119 if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) 120 return 1; 121 122 if ((buf[0] & PMIC_OP_REG_SEL_MASK) != vddx_op_vol_sel) 123 return 1; 124 125 return 0; 126 } 127 128 #define OSC (V_OSCK/1000000) 129 130 const struct dpll_params dpll_mpu_pxm2 = { 131 720, OSC-1, 1, -1, -1, -1, -1}; 132 133 void spl_siemens_board_init(void) 134 { 135 uchar buf[4]; 136 /* 137 * pxm2 PMIC code. All boards currently want an MPU voltage 138 * of 1.2625V and CORE voltage of 1.1375V to operate at 139 * 720MHz. 140 */ 141 if (i2c_probe(PMIC_CTRL_I2C_ADDR)) 142 return; 143 144 /* VDD1/2 voltage selection register access by control i/f */ 145 if (i2c_read(PMIC_CTRL_I2C_ADDR, PMIC_DEVCTRL_REG, 1, buf, 1)) 146 return; 147 148 buf[0] |= PMIC_DEVCTRL_REG_SR_CTL_I2C_SEL_CTL_I2C; 149 150 if (i2c_write(PMIC_CTRL_I2C_ADDR, PMIC_DEVCTRL_REG, 1, buf, 1)) 151 return; 152 153 /* Frequency switching for OPP 120 */ 154 if (voltage_update(MPU, PMIC_OP_REG_SEL_1_2_6) || 155 voltage_update(CORE, PMIC_OP_REG_SEL_1_1_3)) { 156 printf("voltage update failed\n"); 157 } 158 } 159 #endif /* if def CONFIG_SPL_BUILD */ 160 161 int read_eeprom(void) 162 { 163 /* nothing ToDo here for this board */ 164 165 return 0; 166 } 167 168 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 169 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 170 static void cpsw_control(int enabled) 171 { 172 /* VTP can be added here */ 173 174 return; 175 } 176 177 static struct cpsw_slave_data cpsw_slaves[] = { 178 { 179 .slave_reg_ofs = 0x208, 180 .sliver_reg_ofs = 0xd80, 181 .phy_id = 0, 182 .phy_if = PHY_INTERFACE_MODE_RMII, 183 }, 184 { 185 .slave_reg_ofs = 0x308, 186 .sliver_reg_ofs = 0xdc0, 187 .phy_id = 1, 188 .phy_if = PHY_INTERFACE_MODE_RMII, 189 }, 190 }; 191 192 static struct cpsw_platform_data cpsw_data = { 193 .mdio_base = CPSW_MDIO_BASE, 194 .cpsw_base = CPSW_BASE, 195 .mdio_div = 0xff, 196 .channels = 4, 197 .cpdma_reg_ofs = 0x800, 198 .slaves = 1, 199 .slave_data = cpsw_slaves, 200 .ale_reg_ofs = 0xd00, 201 .ale_entries = 1024, 202 .host_port_reg_ofs = 0x108, 203 .hw_stats_reg_ofs = 0x900, 204 .bd_ram_ofs = 0x2000, 205 .mac_control = (1 << 5), 206 .control = cpsw_control, 207 .host_port_num = 0, 208 .version = CPSW_CTRL_VERSION_2, 209 }; 210 #endif /* #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) */ 211 212 #if defined(CONFIG_DRIVER_TI_CPSW) || \ 213 (defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) 214 int board_eth_init(bd_t *bis) 215 { 216 int n = 0; 217 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 218 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 219 struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 220 #ifdef CONFIG_FACTORYSET 221 int rv; 222 if (!is_valid_ether_addr(factory_dat.mac)) 223 printf("Error: no valid mac address\n"); 224 else 225 eth_setenv_enetaddr("ethaddr", factory_dat.mac); 226 #endif /* #ifdef CONFIG_FACTORYSET */ 227 228 /* Set rgmii mode and enable rmii clock to be sourced from chip */ 229 writel(RGMII_MODE_ENABLE , &cdev->miisel); 230 231 rv = cpsw_register(&cpsw_data); 232 if (rv < 0) 233 printf("Error %d registering CPSW switch\n", rv); 234 else 235 n += rv; 236 #endif 237 return n; 238 } 239 #endif /* #if defined(CONFIG_DRIVER_TI_CPSW) */ 240 241 #if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) 242 static struct da8xx_panel lcd_panels[] = { 243 /* AUO G156XW01 V1 */ 244 [0] = { 245 .name = "AUO_G156XW01_V1", 246 .width = 1376, 247 .height = 768, 248 .hfp = 14, 249 .hbp = 64, 250 .hsw = 56, 251 .vfp = 1, 252 .vbp = 28, 253 .vsw = 3, 254 .pxl_clk = 60000000, 255 .invert_pxl_clk = 0, 256 }, 257 /* AUO B101EVN06 V0 */ 258 [1] = { 259 .name = "AUO_B101EVN06_V0", 260 .width = 1280, 261 .height = 800, 262 .hfp = 52, 263 .hbp = 84, 264 .hsw = 36, 265 .vfp = 3, 266 .vbp = 14, 267 .vsw = 6, 268 .pxl_clk = 60000000, 269 .invert_pxl_clk = 0, 270 }, 271 /* 272 * Settings from factoryset 273 * stored in EEPROM 274 */ 275 [2] = { 276 .name = "factoryset", 277 .width = 0, 278 .height = 0, 279 .hfp = 0, 280 .hbp = 0, 281 .hsw = 0, 282 .vfp = 0, 283 .vbp = 0, 284 .vsw = 0, 285 .pxl_clk = 60000000, 286 .invert_pxl_clk = 0, 287 }, 288 }; 289 290 static const struct display_panel disp_panel = { 291 WVGA, 292 32, 293 16, 294 COLOR_ACTIVE, 295 }; 296 297 static const struct lcd_ctrl_config lcd_cfg = { 298 &disp_panel, 299 .ac_bias = 255, 300 .ac_bias_intrpt = 0, 301 .dma_burst_sz = 16, 302 .bpp = 32, 303 .fdd = 0x80, 304 .tft_alt_mode = 0, 305 .stn_565_mode = 0, 306 .mono_8bit_mode = 0, 307 .invert_line_clock = 1, 308 .invert_frm_clock = 1, 309 .sync_edge = 0, 310 .sync_ctrl = 1, 311 .raster_order = 0, 312 }; 313 314 static int set_gpio(int gpio, int state) 315 { 316 gpio_request(gpio, "temp"); 317 gpio_direction_output(gpio, state); 318 gpio_set_value(gpio, state); 319 gpio_free(gpio); 320 return 0; 321 } 322 323 static int enable_backlight(void) 324 { 325 set_gpio(BOARD_LCD_POWER, 1); 326 set_gpio(BOARD_BACK_LIGHT, 1); 327 set_gpio(BOARD_TOUCH_POWER, 1); 328 return 0; 329 } 330 331 static int enable_pwm(void) 332 { 333 struct pwmss_regs *pwmss = (struct pwmss_regs *)PWMSS0_BASE; 334 struct pwmss_ecap_regs *ecap; 335 int ticks = PWM_TICKS; 336 int duty = PWM_DUTY; 337 338 ecap = (struct pwmss_ecap_regs *)AM33XX_ECAP0_BASE; 339 /* enable clock */ 340 setbits_le32(&pwmss->clkconfig, ECAP_CLK_EN); 341 /* TimeStam Counter register */ 342 writel(0xdb9, &ecap->tsctr); 343 /* config period */ 344 writel(ticks - 1, &ecap->cap3); 345 writel(ticks - 1, &ecap->cap1); 346 setbits_le16(&ecap->ecctl2, 347 (ECTRL2_MDSL_ECAP | ECTRL2_SYNCOSEL_MASK | 0xd0)); 348 /* config duty */ 349 writel(duty, &ecap->cap2); 350 writel(duty, &ecap->cap4); 351 /* start */ 352 setbits_le16(&ecap->ecctl2, ECTRL2_CTRSTP_FREERUN); 353 return 0; 354 } 355 356 static struct dpll_regs dpll_lcd_regs = { 357 .cm_clkmode_dpll = CM_WKUP + 0x98, 358 .cm_idlest_dpll = CM_WKUP + 0x48, 359 .cm_clksel_dpll = CM_WKUP + 0x54, 360 }; 361 362 /* no console on this board */ 363 int board_cfb_skip(void) 364 { 365 return 1; 366 } 367 368 #define PLL_GET_M(v) ((v >> 8) & 0x7ff) 369 #define PLL_GET_N(v) (v & 0x7f) 370 371 static int get_clk(struct dpll_regs *dpll_regs) 372 { 373 unsigned int val; 374 unsigned int m, n; 375 int f = 0; 376 377 val = readl(dpll_regs->cm_clksel_dpll); 378 m = PLL_GET_M(val); 379 n = PLL_GET_N(val); 380 f = (m * V_OSCK) / n; 381 382 return f; 383 }; 384 385 int clk_get(int clk) 386 { 387 return get_clk(&dpll_lcd_regs); 388 }; 389 390 static int conf_disp_pll(int m, int n) 391 { 392 struct cm_perpll *cmper = (struct cm_perpll *)CM_PER; 393 struct cm_dpll *cmdpll = (struct cm_dpll *)CM_DPLL; 394 struct dpll_params dpll_lcd = {m, n, -1, -1, -1, -1, -1}; 395 396 u32 *const clk_domains[] = { 397 &cmper->lcdclkctrl, 398 0 399 }; 400 u32 *const clk_modules_explicit_en[] = { 401 &cmper->lcdclkctrl, 402 &cmper->lcdcclkstctrl, 403 &cmper->epwmss0clkctrl, 404 0 405 }; 406 do_enable_clocks(clk_domains, clk_modules_explicit_en, 1); 407 writel(0x0, &cmdpll->clklcdcpixelclk); 408 409 do_setup_dpll(&dpll_lcd_regs, &dpll_lcd); 410 411 return 0; 412 } 413 414 static int board_video_init(void) 415 { 416 /* set 300 MHz */ 417 conf_disp_pll(25, 2); 418 if (factory_dat.pxm50) 419 da8xx_video_init(&lcd_panels[0], &lcd_cfg, lcd_cfg.bpp); 420 else 421 da8xx_video_init(&lcd_panels[1], &lcd_cfg, lcd_cfg.bpp); 422 423 enable_pwm(); 424 enable_backlight(); 425 426 return 0; 427 } 428 #endif 429 #include "../common/board.c" 430