1 /* 2 * Common board functions for siemens AM335X based boards 3 * (C) Copyright 2013 Siemens Schweiz AG 4 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * 6 * Based on: 7 * U-Boot file:/board/ti/am335x/board.c 8 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #include <common.h> 14 #include <errno.h> 15 #include <spl.h> 16 #include <asm/arch/cpu.h> 17 #include <asm/arch/hardware.h> 18 #include <asm/arch/omap.h> 19 #include <asm/arch/ddr_defs.h> 20 #include <asm/arch/clock.h> 21 #include <asm/arch/gpio.h> 22 #include <asm/arch/mmc_host_def.h> 23 #include <asm/arch/sys_proto.h> 24 #include <asm/io.h> 25 #include <asm/emif.h> 26 #include <asm/gpio.h> 27 #include <i2c.h> 28 #include <miiphy.h> 29 #include <cpsw.h> 30 #include <watchdog.h> 31 #include "../common/factoryset.h" 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 #ifdef CONFIG_SPL_BUILD 36 void set_uart_mux_conf(void) 37 { 38 enable_uart0_pin_mux(); 39 } 40 41 void set_mux_conf_regs(void) 42 { 43 /* Initalize the board header */ 44 enable_i2c0_pin_mux(); 45 i2c_set_bus_num(0); 46 if (read_eeprom() < 0) 47 puts("Could not get board ID.\n"); 48 49 enable_board_pin_mux(); 50 } 51 52 void sdram_init(void) 53 { 54 spl_siemens_board_init(); 55 board_init_ddr(); 56 57 return; 58 } 59 #endif /* #ifdef CONFIG_SPL_BUILD */ 60 61 #ifndef CONFIG_SPL_BUILD 62 /* 63 * Basic board specific setup. Pinmux has been handled already. 64 */ 65 int board_init(void) 66 { 67 #if defined(CONFIG_HW_WATCHDOG) 68 hw_watchdog_init(); 69 #endif /* defined(CONFIG_HW_WATCHDOG) */ 70 i2c_set_bus_num(0); 71 if (read_eeprom() < 0) 72 puts("Could not get board ID.\n"); 73 74 gd->bd->bi_arch_number = CONFIG_MACH_TYPE; 75 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 76 77 #ifdef CONFIG_FACTORYSET 78 factoryset_read_eeprom(CONFIG_SYS_I2C_EEPROM_ADDR); 79 #endif 80 gpmc_init(); 81 82 #ifdef CONFIG_VIDEO 83 board_video_init(); 84 #endif 85 86 return 0; 87 } 88 #endif /* #ifndef CONFIG_SPL_BUILD */ 89 90 #define OSC (V_OSCK/1000000) 91 const struct dpll_params dpll_ddr = { 92 DDR_PLL_FREQ, OSC-1, 1, -1, -1, -1, -1}; 93 94 const struct dpll_params *get_dpll_ddr_params(void) 95 { 96 return &dpll_ddr; 97 } 98 99 #ifdef CONFIG_BOARD_LATE_INIT 100 int board_late_init(void) 101 { 102 omap_nand_switch_ecc(1, 8); 103 104 return 0; 105 } 106 #endif 107 108 #ifndef CONFIG_SPL_BUILD 109 #if defined(BOARD_DFU_BUTTON_GPIO) 110 /* 111 * This command returns the status of the user button on 112 * Input - none 113 * Returns - 1 if button is held down 114 * 0 if button is not held down 115 */ 116 static int 117 do_userbutton(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) 118 { 119 int button = 0; 120 int gpio; 121 122 gpio = BOARD_DFU_BUTTON_GPIO; 123 gpio_request(gpio, "DFU"); 124 gpio_direction_input(gpio); 125 if (gpio_get_value(gpio)) 126 button = 1; 127 else 128 button = 0; 129 130 gpio_free(gpio); 131 if (!button) { 132 /* LED0 - RED=1: GPIO2_0 2*32 = 64 */ 133 gpio_request(BOARD_DFU_BUTTON_LED, ""); 134 gpio_direction_output(BOARD_DFU_BUTTON_LED, 1); 135 gpio_set_value(BOARD_DFU_BUTTON_LED, 1); 136 } 137 138 return button; 139 } 140 141 U_BOOT_CMD( 142 dfubutton, CONFIG_SYS_MAXARGS, 1, do_userbutton, 143 "Return the status of the DFU button", 144 "" 145 ); 146 #endif 147 148 static int 149 do_usertestwdt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) 150 { 151 printf("\n\n\n Go into infinite loop\n\n\n"); 152 while (1) 153 ; 154 return 0; 155 }; 156 157 U_BOOT_CMD( 158 testwdt, CONFIG_SYS_MAXARGS, 1, do_usertestwdt, 159 "Sends U-Boot into infinite loop", 160 "" 161 ); 162 #endif /* !CONFIG_SPL_BUILD */ 163