1Intro: 2====== 3 4The SBC8548 is a stand alone single board computer with a 1GHz 5MPC8548 CPU, 8MB boot flash, 64MB user flash and, 256MB DDR2 400MHz 6memory. It also has 128MB SDRAM 100MHz LBC memory, with both a PCI-e, 7and a PCI-X slot, dual mini-DB9 for UART, and dual RJ-45 for eTSEC 8ethernet connections. 9 10U-boot Configuration: 11===================== 12 13The following possible u-boot configuration targets are available: 14 15 1) sbc8548_config 16 2) sbc8548_PCI_33_config 17 3) sbc8548_PCI_66_config 18 4) sbc8548_PCI_33_PCIE_config 19 5) sbc8548_PCI_66_PCIE_config 20 21Generally speaking, most people should choose to use #5. Details 22of each choice are listed below. 23 24Choice #1 does not enable CONFIG_PCI, and assumes that the PCI slot 25will be left empty (M66EN high), and so the board will operate with 26a base clock of 66MHz. Note that you need both PCI enabled in u-boot 27and linux in order to have functional PCI under linux. 28 29The second enables PCI support and builds for a 33MHz clock rate. Note 30that if a 33MHz 32bit card is inserted in the slot, then the whole board 31will clock down to a 33MHz base clock instead of the default 66MHz. This 32will change the baud clocks and mess up your serial console output if you 33were previously running at 66MHz. If you want to use a 33MHz PCI card, 34then you should build a U-Boot with a _PCI_33_ config and store this 35to flash prior to powering down the board and inserting the 33MHz PCI 36card. [The above discussion assumes that the SW2[1-4] has not been changed 37to reflect a different CCB:SYSCLK ratio] 38 39The third option builds PCI support in, and leaves the clocking at the 40default 66MHz. Options four and five are just repeats of option two 41and three, but with PCI-e support enabled as well. 42 43PCI output listing with an intel e1000 PCI-x and a Syskonnect SK-9Exx 44is shown below for sbc8548_PCI_66_PCIE_config. (Note that PCI-e with 45a 33MHz PCI configuration is currently untested.) 46 47 => pci 0 48 Scanning PCI devices on bus 0 49 BusDevFun VendorId DeviceId Device Class Sub-Class 50 _____________________________________________________________ 51 00.00.00 0x1057 0x0012 Processor 0x20 52 00.01.00 0x8086 0x1026 Network controller 0x00 53 => pci 1 54 Scanning PCI devices on bus 1 55 BusDevFun VendorId DeviceId Device Class Sub-Class 56 _____________________________________________________________ 57 01.00.00 0x1957 0x0012 Processor 0x20 58 => pci 2 59 Scanning PCI devices on bus 2 60 BusDevFun VendorId DeviceId Device Class Sub-Class 61 _____________________________________________________________ 62 02.00.00 0x1148 0x9e00 Network controller 0x00 63 => 64 65Memory Size and using SPD: 66========================== 67 68The default configuration uses hard coded memory configuration settings 69for 256MB of DDR2 @400MHz. It does not by default use the DDR2 SPD 70EEPROM data to read what memory is installed. 71 72There is a hardware errata, which causes the older local bus SDRAM 73SPD EEPROM to land at the same address as the DDR2 SPD EEPROM, so 74that the SPD data can not be read reliably. You can test if your 75board has the errata fix by running "i2c probe". If you see 0x53 76as a valid device, it has been fixed. If you only see 0x50, 0x51 77then your board does not have the fix. 78 79You can also visually inspect the board to see if this hardware 80fix has been applied: 81 82 1) Remove R314 (RES-R0174-033, 1K, 0603). R314 is located on 83 the back of the PCB behind the DDR SDRAM SODIMM connector. 84 2) Solder RES-R0174-033 (1K, 0603) resistor from R314 pin 2 pad 85 to R313 pin 2. Pin 2 for each resistor is the end of the 86 resistor closest to the CPU. 87 88Boards without the mod will have R314 and R313 in parallel, like "||". 89After the mod, they will be touching and form an "L" shape. 90 91If you want to upgrade to larger RAM size, you can simply enable 92 #define CONFIG_SPD_EEPROM 93 #define CONFIG_DDR_SPD 94in include/configs/sbc8548.h file. (The lines are already there 95but listed as #undef). 96 97If you did the i2c test, and your board does not have the errata 98fix, then you will have to physically remove the LBC 128MB DIMM 99from the board's socket to resolve the above i2c address overlap 100issue and allow SPD autodetection of RAM to work. 101 102 103Updating U-boot with U-boot: 104============================ 105 106Note that versions of u-boot up to and including 2009.08 had u-boot stored 107at 0xfff8_0000 -> 0xffff_ffff (512k). Currently it is being stored from 1080xfffa_0000 -> 0xffff_ffff (384k). If you use an old macro/script to 109update u-boot with u-boot and it uses the old address, you will render 110your board inoperable, and you will require JTAG recovery. 111 112The following steps list how to update with the current address: 113 114 tftp u-boot.bin 115 md 200000 10 116 protect off all 117 erase fffa0000 ffffffff 118 cp.b 200000 fffa0000 60000 119 md fffa0000 10 120 protect on all 121 122The "md" steps in the above are just a precautionary step that allow 123you to confirm the u-boot version that was downloaded, and then confirm 124that it was copied to flash. 125 126The above assumes that you are using the default board settings which 127have u-boot in the 8MB flash, tied to /CS0. 128 129If you are running the default 8MB /CS0 settings but want to store an 130image in the SODIMM that is built with CONFIG_SYS_ALT_BOOT enabled, 131(as a backup, etc) then the steps will become: 132 133 tftp u-boot.bin 134 md 200000 10 135 protect off all 136 era eff00000 efffffff 137 cp.b 200000 eff00000 100000 138 md eff00000 10 139 protect on all 140 141Finally, if you are running the alternate 64MB /CS0 settings and want 142to update the in-use u-boot image, then (again with CONFIG_SYS_ALT_BOOT 143enabled) the steps will become: 144 145 tftp u-boot.bin 146 md 200000 10 147 protect off all 148 era fff00000 ffffffff 149 cp.b 200000 fff00000 100000 150 md fff00000 10 151 protect on all 152 153 154Hardware Reference: 155=================== 156 157The following contains some summary information on hardware settings 158that are relevant to u-boot, based on the board manual. For the 159most up to date and complete details of the board, please request the 160reference manual ERG-00327-001.pdf from www.windriver.com 161 162Boot flash: 163 intel V28F640Jx, 8192x8 (one device) at 0xff80_0000 164 165Sodimm flash: 166 intel V28F128Jx, 16384x8 (4 devices) at 0xfb80_0000 167 Note that this address reflects the default setting for 168 the JTAG debugging tools, but since the alignment is 169 rather inconvenient, u-boot puts it at 0xec00_0000. 170 171 172 Jumpers: 173 174Jumper Name ON OFF 175---------------------------------------------------------------- 176JP12 CS0/CS6 swap see note[*] see note[*] 177 178JP13 SODIMM flash write OK writes disabled 179 write prot. 180 181JP14 HRESET/TRST joined isolated 182 183JP15 PWR ON when AC pwr use S1 for on/off 184 185JP16 Demo LEDs lit not lit 186 187JP19 PCI mode PCI PCI-X 188 189 190[*]JP12, when jumpered parallel to the SODIMM, puts the boot flash 191onto /CS0 and the SODIMM flash on /CS6 (default). When JP12 192is jumpered parallel to the LBC-SDRAM, then /CS0 is for the 193SODIMM flash and /CS6 is for the boot flash. Note that in this 194alternate setting, you also need to switch SW2.8 to ON. 195See the setting CONFIG_SYS_ALT_BOOT if you want to use this setting 196and boot u-boot from the 64MB SODIMM 197 198 199 Switches: 200 201The defaults are marked with a * 202 203Name Desc. ON OFF 204------------------------------------------------------------------ 205S1 Pwr toggle n/a n/a 206 207SW2.1 CFG_SYS_PLL0 1 0* 208SW2.2 CFG_SYS_PLL1 1* 0 209SW2.3 CFG_SYS_PLL2 1* 0 210SW2.4 CFG_SYS_PLL3 1 0* 211SW2.5 CFG_CORE_PLL0 1* 0 212SW2.6 CFG_CORE_PLL1 1 0* 213SW2.7 CFG_CORE_PLL2 1* 0 214SW2.8 CFG_ROM_LOC1 1 0* 215 216SW3.1 CFG_HOST_AGT0 1* 0 217SW3.2 CFG_HOST_AGT1 1* 0 218SW3.3 CFG_HOST_AGT2 1* 0 219SW3.4 CFG_IO_PORTS0 1* 0 220SW3.5 CFG_IO_PORTS0 1 0* 221SW3.6 CFG_IO_PORTS0 1 0* 222 223SerDes CLK(MHz) SW5.1 SW5.2 224---------------------------------------------- 22525 0 0 226100* 1 0 227125 0 1 228200 1 1 229 230SerDes CLK spread SW5.3 SW5.4 231---------------------------------------------- 232+/- 0.25% 0 0 233-0.50% 1 0 234-0.75% 0 1 235No Spread* 1 1 236 237SW4 settings are readable from the EPLD and are currently not used for 238any hardware settings (i.e. user configuration switches). 239 240 LEDs: 241 242Name Desc. ON OFF 243------------------------------------------------------------------ 244D13 PCI/PCI-X PCI-X PCI 245D14 3.3V PWR 3.3V no power 246D15 SYSCLK 66MHz 33MHz 247 248 249 Default Memory Map: 250 251start end CS<n> width Desc. 252---------------------------------------------------------------------- 2530000_0000 0fff_ffff MCS0,1 64 DDR2 (256MB) 254f000_0000 f7ff_ffff CS3,4 32 LB SDRAM (128MB) 255f800_0000 f8b0_1fff CS5 - EPLD 256fb80_0000 ff7f_ffff CS6 32 SODIMM flash (64MB) [*] 257ff80_0000 ffff_ffff CS0 8 Boot flash (8MB) 258 259[*] fb80 represents the default programmed by WR JTAG register files, 260 but u-boot places the flash at either ec00 or fc00 based on JP12. 261 262The EPLD on CS5 demuxes the following devices at the following offsets: 263 264offset size width device 265-------------------------------------------------------- 2660 1fff 8 7 segment display LED 26710_0000 1fff 4 user switches 26830_0000 1fff 4 HW Rev. register 269b0_0000 1fff 8 8kB EEPROM 270