1 /* 2 * Copyright (C) 2016 samtec automotive software & electronics gmbh 3 * 4 * Author: Christoph Fritz <chf.fritz@googlemail.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <asm/arch/clock.h> 10 #include <asm/arch/crm_regs.h> 11 #include <asm/arch/iomux.h> 12 #include <asm/arch/imx-regs.h> 13 #include <asm/arch/mx6-pins.h> 14 #include <asm/arch/sys_proto.h> 15 #include <asm/gpio.h> 16 #include <asm/mach-imx/iomux-v3.h> 17 #include <asm/io.h> 18 #include <asm/mach-imx/mxc_i2c.h> 19 #include <linux/sizes.h> 20 #include <common.h> 21 #include <fsl_esdhc.h> 22 #include <mmc.h> 23 #include <i2c.h> 24 #include <miiphy.h> 25 #include <netdev.h> 26 #include <power/pmic.h> 27 #include <power/pfuze100_pmic.h> 28 #include <usb.h> 29 #include <usb/ehci-ci.h> 30 #include <pwm.h> 31 #include <wait_bit.h> 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 #define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \ 36 PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 37 PAD_CTL_SRE_FAST) 38 39 #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PKE | \ 40 PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | \ 41 PAD_CTL_SRE_FAST) 42 43 #define ENET_CLK_PAD_CTRL PAD_CTL_DSE_34ohm 44 45 #define ENET_RX_PAD_CTRL (PAD_CTL_PKE | \ 46 PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_HIGH | \ 47 PAD_CTL_SRE_FAST) 48 49 #define I2C_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \ 50 PAD_CTL_PKE | PAD_CTL_ODE | PAD_CTL_SPEED_MED | \ 51 PAD_CTL_DSE_40ohm) 52 53 #define USDHC_CLK_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ 54 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST) 55 56 #define USDHC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \ 57 PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm | \ 58 PAD_CTL_SRE_FAST) 59 60 #define GPIO_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \ 61 PAD_CTL_PKE) 62 63 int dram_init(void) 64 { 65 gd->ram_size = imx_ddr_size(); 66 67 return 0; 68 } 69 70 static iomux_v3_cfg_t const uart1_pads[] = { 71 MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), 72 MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), 73 }; 74 75 static iomux_v3_cfg_t const usdhc2_pads[] = { 76 MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL), 77 MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 78 MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 79 MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 80 MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 81 MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 82 MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL), 83 }; 84 85 static iomux_v3_cfg_t const usdhc4_pads[] = { 86 MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL), 87 MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 88 MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 89 MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 90 MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 91 MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 92 MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 93 MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 94 MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 95 MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 96 }; 97 98 static iomux_v3_cfg_t const fec1_pads[] = { 99 MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 100 MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 101 MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 102 MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 103 MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 104 MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 105 MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 106 MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), 107 MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL) | 108 MUX_MODE_SION, 109 /* LAN8720 PHY Reset */ 110 MX6_PAD_RGMII1_TD3__GPIO5_IO_9 | MUX_PAD_CTRL(NO_PAD_CTRL), 111 }; 112 113 static iomux_v3_cfg_t const pwm_led_pads[] = { 114 MX6_PAD_RGMII2_RD2__PWM2_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* green */ 115 MX6_PAD_RGMII2_TD2__PWM6_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* red */ 116 MX6_PAD_RGMII2_RD3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* blue */ 117 }; 118 119 static void setup_iomux_uart(void) 120 { 121 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); 122 } 123 124 #define PHY_RESET IMX_GPIO_NR(5, 9) 125 126 int board_eth_init(bd_t *bis) 127 { 128 struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 129 int ret; 130 unsigned char eth1addr[6]; 131 132 /* just to get secound mac address */ 133 imx_get_mac_from_fuse(1, eth1addr); 134 if (!getenv("eth1addr") && is_valid_ethaddr(eth1addr)) 135 eth_setenv_enetaddr("eth1addr", eth1addr); 136 137 imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads)); 138 139 /* 140 * Generate phy reference clock via pin IOMUX ENET_REF_CLK1/2 by erasing 141 * ENET1/2_TX_CLK_DIR gpr1[14:13], so that reference clock is driven by 142 * ref_enetpll0/1 and enable ENET1/2_TX_CLK output driver. 143 */ 144 clrsetbits_le32(&iomuxc_regs->gpr[1], 145 IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK | 146 IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK, 147 IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK | 148 IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK); 149 150 ret = enable_fec_anatop_clock(0, ENET_50MHZ); 151 if (ret) 152 goto eth_fail; 153 154 /* reset phy */ 155 gpio_direction_output(PHY_RESET, 0); 156 mdelay(16); 157 gpio_set_value(PHY_RESET, 1); 158 mdelay(1); 159 160 ret = fecmxc_initialize_multi(bis, 0, CONFIG_FEC_MXC_PHYADDR, 161 IMX_FEC_BASE); 162 if (ret) 163 goto eth_fail; 164 165 return ret; 166 167 eth_fail: 168 printf("FEC MXC: %s:failed (%i)\n", __func__, ret); 169 gpio_set_value(PHY_RESET, 0); 170 return ret; 171 } 172 173 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) 174 /* I2C1 for PMIC */ 175 static struct i2c_pads_info i2c_pad_info1 = { 176 .scl = { 177 .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC, 178 .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC, 179 .gp = IMX_GPIO_NR(1, 0), 180 }, 181 .sda = { 182 .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC, 183 .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC, 184 .gp = IMX_GPIO_NR(1, 1), 185 }, 186 }; 187 188 static struct pmic *pfuze_init(unsigned char i2cbus) 189 { 190 struct pmic *p; 191 int ret; 192 u32 reg; 193 194 ret = power_pfuze100_init(i2cbus); 195 if (ret) 196 return NULL; 197 198 p = pmic_get("PFUZE100"); 199 ret = pmic_probe(p); 200 if (ret) 201 return NULL; 202 203 pmic_reg_read(p, PFUZE100_DEVICEID, ®); 204 printf("PMIC: PFUZE100 ID=0x%02x\n", reg); 205 206 /* Set SW1AB stanby volage to 0.975V */ 207 pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®); 208 reg &= ~SW1x_STBY_MASK; 209 reg |= SW1x_0_975V; 210 pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg); 211 212 /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ 213 pmic_reg_read(p, PFUZE100_SW1ABCONF, ®); 214 reg &= ~SW1xCONF_DVSSPEED_MASK; 215 reg |= SW1xCONF_DVSSPEED_4US; 216 pmic_reg_write(p, PFUZE100_SW1ABCONF, reg); 217 218 /* Set SW1C standby voltage to 0.975V */ 219 pmic_reg_read(p, PFUZE100_SW1CSTBY, ®); 220 reg &= ~SW1x_STBY_MASK; 221 reg |= SW1x_0_975V; 222 pmic_reg_write(p, PFUZE100_SW1CSTBY, reg); 223 224 /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */ 225 pmic_reg_read(p, PFUZE100_SW1CCONF, ®); 226 reg &= ~SW1xCONF_DVSSPEED_MASK; 227 reg |= SW1xCONF_DVSSPEED_4US; 228 pmic_reg_write(p, PFUZE100_SW1CCONF, reg); 229 230 return p; 231 } 232 233 static int pfuze_mode_init(struct pmic *p, u32 mode) 234 { 235 unsigned char offset, i, switch_num; 236 u32 id; 237 int ret; 238 239 pmic_reg_read(p, PFUZE100_DEVICEID, &id); 240 id = id & 0xf; 241 242 if (id == 0) { 243 switch_num = 6; 244 offset = PFUZE100_SW1CMODE; 245 } else if (id == 1) { 246 switch_num = 4; 247 offset = PFUZE100_SW2MODE; 248 } else { 249 printf("Not supported, id=%d\n", id); 250 return -EINVAL; 251 } 252 253 ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode); 254 if (ret < 0) { 255 printf("Set SW1AB mode error!\n"); 256 return ret; 257 } 258 259 for (i = 0; i < switch_num - 1; i++) { 260 ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode); 261 if (ret < 0) { 262 printf("Set switch 0x%x mode error!\n", 263 offset + i * SWITCH_SIZE); 264 return ret; 265 } 266 } 267 268 return ret; 269 } 270 271 int power_init_board(void) 272 { 273 struct pmic *p; 274 int ret; 275 276 p = pfuze_init(I2C_PMIC); 277 if (!p) 278 return -ENODEV; 279 280 ret = pfuze_mode_init(p, APS_PFM); 281 if (ret < 0) 282 return ret; 283 284 return 0; 285 } 286 287 #ifdef CONFIG_USB_EHCI_MX6 288 static iomux_v3_cfg_t const usb_otg_pads[] = { 289 /* OGT1 */ 290 MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 291 MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL), 292 /* OTG2 */ 293 MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL) 294 }; 295 296 static void setup_iomux_usb(void) 297 { 298 imx_iomux_v3_setup_multiple_pads(usb_otg_pads, 299 ARRAY_SIZE(usb_otg_pads)); 300 } 301 302 int board_usb_phy_mode(int port) 303 { 304 if (port == 1) 305 return USB_INIT_HOST; 306 else 307 return usb_phy_mode(port); 308 } 309 #endif 310 311 #ifdef CONFIG_PWM_IMX 312 static int set_pwm_leds(void) 313 { 314 int ret; 315 316 imx_iomux_v3_setup_multiple_pads(pwm_led_pads, 317 ARRAY_SIZE(pwm_led_pads)); 318 /* enable backlight PWM 2, green LED */ 319 ret = pwm_init(1, 0, 0); 320 if (ret) 321 goto error; 322 /* duty cycle 200ns, period: 8000ns */ 323 ret = pwm_config(1, 200, 8000); 324 if (ret) 325 goto error; 326 ret = pwm_enable(1); 327 if (ret) 328 goto error; 329 330 /* enable backlight PWM 1, blue LED */ 331 ret = pwm_init(0, 0, 0); 332 if (ret) 333 goto error; 334 /* duty cycle 200ns, period: 8000ns */ 335 ret = pwm_config(0, 200, 8000); 336 if (ret) 337 goto error; 338 ret = pwm_enable(0); 339 if (ret) 340 goto error; 341 342 /* enable backlight PWM 6, red LED */ 343 ret = pwm_init(5, 0, 0); 344 if (ret) 345 goto error; 346 /* duty cycle 200ns, period: 8000ns */ 347 ret = pwm_config(5, 200, 8000); 348 if (ret) 349 goto error; 350 ret = pwm_enable(5); 351 352 error: 353 return ret; 354 } 355 #else 356 static int set_pwm_leds(void) 357 { 358 return 0; 359 } 360 #endif 361 362 #define ADCx_HC0 0x00 363 #define ADCx_HS 0x08 364 #define ADCx_HS_C0 BIT(0) 365 #define ADCx_R0 0x0c 366 #define ADCx_CFG 0x14 367 #define ADCx_CFG_SWMODE 0x308 368 #define ADCx_GC 0x18 369 #define ADCx_GC_CAL BIT(7) 370 371 static int read_adc(u32 *val) 372 { 373 int ret; 374 void __iomem *b = map_physmem(ADC1_BASE_ADDR, 0x100, MAP_NOCACHE); 375 376 /* use software mode */ 377 writel(ADCx_CFG_SWMODE, b + ADCx_CFG); 378 379 /* start auto calibration */ 380 setbits_le32(b + ADCx_GC, ADCx_GC_CAL); 381 ret = wait_for_bit("ADC", b + ADCx_GC, ADCx_GC_CAL, ADCx_GC_CAL, 10, 0); 382 if (ret) 383 goto adc_exit; 384 385 /* start conversion */ 386 writel(0, b + ADCx_HC0); 387 388 /* wait for conversion */ 389 ret = wait_for_bit("ADC", b + ADCx_HS, ADCx_HS_C0, ADCx_HS_C0, 10, 0); 390 if (ret) 391 goto adc_exit; 392 393 /* read result */ 394 *val = readl(b + ADCx_R0); 395 396 adc_exit: 397 if (ret) 398 printf("ADC failure (ret=%i)\n", ret); 399 unmap_physmem(b, MAP_NOCACHE); 400 return ret; 401 } 402 403 #define VAL_UPPER 2498 404 #define VAL_LOWER 1550 405 406 static int set_pin_state(void) 407 { 408 u32 val; 409 int ret; 410 411 ret = read_adc(&val); 412 if (ret) 413 return ret; 414 415 if (val >= VAL_UPPER) 416 setenv("pin_state", "connected"); 417 else if (val < VAL_UPPER && val > VAL_LOWER) 418 setenv("pin_state", "open"); 419 else 420 setenv("pin_state", "button"); 421 422 return ret; 423 } 424 425 int board_late_init(void) 426 { 427 int ret; 428 429 ret = set_pwm_leds(); 430 if (ret) 431 return ret; 432 433 ret = set_pin_state(); 434 435 return ret; 436 } 437 438 int board_early_init_f(void) 439 { 440 setup_iomux_uart(); 441 442 setup_iomux_usb(); 443 444 return 0; 445 } 446 447 static struct fsl_esdhc_cfg usdhc_cfg[2] = { 448 {USDHC4_BASE_ADDR, 0, 8}, 449 {USDHC2_BASE_ADDR, 0, 4}, 450 }; 451 452 #define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28) 453 454 int board_mmc_getcd(struct mmc *mmc) 455 { 456 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 457 458 if (cfg->esdhc_base == USDHC4_BASE_ADDR) 459 return 1; 460 if (cfg->esdhc_base == USDHC2_BASE_ADDR) 461 return !gpio_get_value(USDHC2_CD_GPIO); 462 463 return -EINVAL; 464 } 465 466 int board_mmc_init(bd_t *bis) 467 { 468 int ret; 469 470 /* 471 * According to the board_mmc_init() the following map is done: 472 * (U-Boot device node) (Physical Port) 473 * mmc0 USDHC4 474 * mmc1 USDHC2 475 */ 476 imx_iomux_v3_setup_multiple_pads( 477 usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); 478 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); 479 480 imx_iomux_v3_setup_multiple_pads( 481 usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); 482 gpio_direction_input(USDHC2_CD_GPIO); 483 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 484 485 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]); 486 if (ret) { 487 printf("Warning: failed to initialize USDHC4\n"); 488 return ret; 489 } 490 491 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]); 492 if (ret) { 493 printf("Warning: failed to initialize USDHC2\n"); 494 return ret; 495 } 496 497 return 0; 498 } 499 500 int board_init(void) 501 { 502 /* Address of boot parameters */ 503 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 504 505 #ifdef CONFIG_SYS_I2C_MXC 506 setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); 507 #endif 508 509 return 0; 510 } 511 512 int checkboard(void) 513 { 514 puts("Board: VIN|ING 2000\n"); 515 516 return 0; 517 } 518