1 /* 2 * Maintainer : Steve Sakoman <steve@sakoman.com> 3 * 4 * Derived from Beagle Board, 3430 SDP, and OMAP3EVM code by 5 * Richard Woodruff <r-woodruff2@ti.com> 6 * Syed Mohammed Khasim <khasim@ti.com> 7 * Sunil Kumar <sunilsaini05@gmail.com> 8 * Shashi Ranjan <shashiranjanmca05@gmail.com> 9 * 10 * (C) Copyright 2004-2008 11 * Texas Instruments, <www.ti.com> 12 * 13 * See file CREDITS for list of people who contributed to this 14 * project. 15 * 16 * This program is free software; you can redistribute it and/or 17 * modify it under the terms of the GNU General Public License as 18 * published by the Free Software Foundation; either version 2 of 19 * the License, or (at your option) any later version. 20 * 21 * This program is distributed in the hope that it will be useful, 22 * but WITHOUT ANY WARRANTY; without even the implied warranty of 23 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 24 * GNU General Public License for more details. 25 * 26 * You should have received a copy of the GNU General Public License 27 * along with this program; if not, write to the Free Software 28 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 29 * MA 02111-1307 USA 30 */ 31 #include <common.h> 32 #include <netdev.h> 33 #include <twl4030.h> 34 #include <linux/mtd/nand.h> 35 #include <asm/io.h> 36 #include <asm/arch/mmc_host_def.h> 37 #include <asm/arch/mux.h> 38 #include <asm/arch/mem.h> 39 #include <asm/arch/sys_proto.h> 40 #include <asm/arch/omap_gpmc.h> 41 #include <asm/gpio.h> 42 #include <asm/mach-types.h> 43 #include "overo.h" 44 45 DECLARE_GLOBAL_DATA_PTR; 46 47 #define TWL4030_I2C_BUS 0 48 #define EXPANSION_EEPROM_I2C_BUS 2 49 #define EXPANSION_EEPROM_I2C_ADDRESS 0x51 50 51 #define GUMSTIX_SUMMIT 0x01000200 52 #define GUMSTIX_TOBI 0x02000200 53 #define GUMSTIX_TOBI_DUO 0x03000200 54 #define GUMSTIX_PALO35 0x04000200 55 #define GUMSTIX_PALO43 0x05000200 56 #define GUMSTIX_CHESTNUT43 0x06000200 57 #define GUMSTIX_PINTO 0x07000200 58 #define GUMSTIX_GALLOP43 0x08000200 59 60 #define ETTUS_USRP_E 0x01000300 61 62 #define GUMSTIX_NO_EEPROM 0xffffffff 63 64 static struct { 65 unsigned int device_vendor; 66 unsigned char revision; 67 unsigned char content; 68 char fab_revision[8]; 69 char env_var[16]; 70 char env_setting[64]; 71 } expansion_config; 72 73 #if defined(CONFIG_CMD_NET) 74 static void setup_net_chip(void); 75 #endif 76 77 /* GPMC definitions for LAN9221 chips on Tobi expansion boards */ 78 static const u32 gpmc_lan_config[] = { 79 NET_LAN9221_GPMC_CONFIG1, 80 NET_LAN9221_GPMC_CONFIG2, 81 NET_LAN9221_GPMC_CONFIG3, 82 NET_LAN9221_GPMC_CONFIG4, 83 NET_LAN9221_GPMC_CONFIG5, 84 NET_LAN9221_GPMC_CONFIG6, 85 /*CONFIG7- computed as params */ 86 }; 87 88 /* 89 * Routine: board_init 90 * Description: Early hardware init. 91 */ 92 int board_init(void) 93 { 94 gpmc_init(); /* in SRAM or SDRAM, finish GPMC */ 95 /* board id for Linux */ 96 gd->bd->bi_arch_number = MACH_TYPE_OVERO; 97 /* boot param addr */ 98 gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); 99 100 return 0; 101 } 102 103 /* 104 * Routine: omap_rev_string 105 * Description: For SPL builds output board rev 106 */ 107 #ifdef CONFIG_SPL_BUILD 108 void omap_rev_string(void) 109 { 110 } 111 #endif 112 113 /* 114 * Routine: get_board_revision 115 * Description: Returns the board revision 116 */ 117 int get_board_revision(void) 118 { 119 int revision; 120 121 #ifdef CONFIG_DRIVER_OMAP34XX_I2C 122 unsigned char data; 123 124 /* board revisions <= R2410 connect 4030 irq_1 to gpio112 */ 125 /* these boards should return a revision number of 0 */ 126 /* the code below forces a 4030 RTC irq to ensure that gpio112 is low */ 127 i2c_set_bus_num(TWL4030_I2C_BUS); 128 data = 0x01; 129 i2c_write(0x4B, 0x29, 1, &data, 1); 130 data = 0x0c; 131 i2c_write(0x4B, 0x2b, 1, &data, 1); 132 i2c_read(0x4B, 0x2a, 1, &data, 1); 133 #endif 134 135 if (!gpio_request(112, "") && 136 !gpio_request(113, "") && 137 !gpio_request(115, "")) { 138 139 gpio_direction_input(112); 140 gpio_direction_input(113); 141 gpio_direction_input(115); 142 143 revision = gpio_get_value(115) << 2 | 144 gpio_get_value(113) << 1 | 145 gpio_get_value(112); 146 } else { 147 puts("Error: unable to acquire board revision GPIOs\n"); 148 revision = -1; 149 } 150 151 return revision; 152 } 153 154 #ifdef CONFIG_SPL_BUILD 155 /* 156 * Routine: get_board_mem_timings 157 * Description: If we use SPL then there is no x-loader nor config header 158 * so we have to setup the DDR timings ourself on both banks. 159 */ 160 void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl, 161 u32 *mr) 162 { 163 *mr = MICRON_V_MR_165; 164 switch (get_board_revision()) { 165 case REVISION_0: /* Micron 1286MB/256MB, 1/2 banks of 128MB */ 166 *mcfg = MICRON_V_MCFG_165(128 << 20); 167 *ctrla = MICRON_V_ACTIMA_165; 168 *ctrlb = MICRON_V_ACTIMB_165; 169 *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 170 break; 171 case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */ 172 *mcfg = MICRON_V_MCFG_165(256 << 20); 173 *ctrla = MICRON_V_ACTIMA_165; 174 *ctrlb = MICRON_V_ACTIMB_165; 175 *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 176 break; 177 case REVISION_2: /* Hynix 256MB/512MB, 1/2 banks of 256MB */ 178 *mcfg = HYNIX_V_MCFG_165(256 << 20); 179 *ctrla = HYNIX_V_ACTIMA_165; 180 *ctrlb = HYNIX_V_ACTIMB_165; 181 *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 182 break; 183 default: 184 *mcfg = MICRON_V_MCFG_165(128 << 20); 185 *ctrla = MICRON_V_ACTIMA_165; 186 *ctrlb = MICRON_V_ACTIMB_165; 187 *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 188 } 189 } 190 #endif 191 192 /* 193 * Routine: get_sdio2_config 194 * Description: Return information about the wifi module connection 195 * Returns 0 if the module connects though a level translator 196 * Returns 1 if the module connects directly 197 */ 198 int get_sdio2_config(void) 199 { 200 int sdio_direct; 201 202 if (!gpio_request(130, "") && !gpio_request(139, "")) { 203 204 gpio_direction_output(130, 0); 205 gpio_direction_input(139); 206 207 sdio_direct = 1; 208 gpio_set_value(130, 0); 209 if (gpio_get_value(139) == 0) { 210 gpio_set_value(130, 1); 211 if (gpio_get_value(139) == 1) 212 sdio_direct = 0; 213 } 214 215 gpio_direction_input(130); 216 } else { 217 puts("Error: unable to acquire sdio2 clk GPIOs\n"); 218 sdio_direct = -1; 219 } 220 221 return sdio_direct; 222 } 223 224 /* 225 * Routine: get_expansion_id 226 * Description: This function checks for expansion board by checking I2C 227 * bus 2 for the availability of an AT24C01B serial EEPROM. 228 * returns the device_vendor field from the EEPROM 229 */ 230 unsigned int get_expansion_id(void) 231 { 232 i2c_set_bus_num(EXPANSION_EEPROM_I2C_BUS); 233 234 /* return GUMSTIX_NO_EEPROM if eeprom doesn't respond */ 235 if (i2c_probe(EXPANSION_EEPROM_I2C_ADDRESS) == 1) { 236 i2c_set_bus_num(TWL4030_I2C_BUS); 237 return GUMSTIX_NO_EEPROM; 238 } 239 240 /* read configuration data */ 241 i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 1, (u8 *)&expansion_config, 242 sizeof(expansion_config)); 243 244 i2c_set_bus_num(TWL4030_I2C_BUS); 245 246 return expansion_config.device_vendor; 247 } 248 249 /* 250 * Routine: misc_init_r 251 * Description: Configure board specific parts 252 */ 253 int misc_init_r(void) 254 { 255 twl4030_power_init(); 256 twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON); 257 258 #if defined(CONFIG_CMD_NET) 259 setup_net_chip(); 260 #endif 261 262 printf("Board revision: %d\n", get_board_revision()); 263 264 switch (get_sdio2_config()) { 265 case 0: 266 puts("Tranceiver detected on mmc2\n"); 267 MUX_OVERO_SDIO2_TRANSCEIVER(); 268 break; 269 case 1: 270 puts("Direct connection on mmc2\n"); 271 MUX_OVERO_SDIO2_DIRECT(); 272 break; 273 default: 274 puts("Unable to detect mmc2 connection type\n"); 275 } 276 277 switch (get_expansion_id()) { 278 case GUMSTIX_SUMMIT: 279 printf("Recognized Summit expansion board (rev %d %s)\n", 280 expansion_config.revision, 281 expansion_config.fab_revision); 282 setenv("defaultdisplay", "dvi"); 283 break; 284 case GUMSTIX_TOBI: 285 printf("Recognized Tobi expansion board (rev %d %s)\n", 286 expansion_config.revision, 287 expansion_config.fab_revision); 288 setenv("defaultdisplay", "dvi"); 289 break; 290 case GUMSTIX_TOBI_DUO: 291 printf("Recognized Tobi Duo expansion board (rev %d %s)\n", 292 expansion_config.revision, 293 expansion_config.fab_revision); 294 /* second lan chip */ 295 enable_gpmc_cs_config(gpmc_lan_config, &gpmc_cfg->cs[4], 296 0x2B000000, GPMC_SIZE_16M); 297 break; 298 case GUMSTIX_PALO35: 299 printf("Recognized Palo35 expansion board (rev %d %s)\n", 300 expansion_config.revision, 301 expansion_config.fab_revision); 302 setenv("defaultdisplay", "lcd35"); 303 break; 304 case GUMSTIX_PALO43: 305 printf("Recognized Palo43 expansion board (rev %d %s)\n", 306 expansion_config.revision, 307 expansion_config.fab_revision); 308 setenv("defaultdisplay", "lcd43"); 309 break; 310 case GUMSTIX_CHESTNUT43: 311 printf("Recognized Chestnut43 expansion board (rev %d %s)\n", 312 expansion_config.revision, 313 expansion_config.fab_revision); 314 setenv("defaultdisplay", "lcd43"); 315 break; 316 case GUMSTIX_PINTO: 317 printf("Recognized Pinto expansion board (rev %d %s)\n", 318 expansion_config.revision, 319 expansion_config.fab_revision); 320 break; 321 case GUMSTIX_GALLOP43: 322 printf("Recognized Gallop43 expansion board (rev %d %s)\n", 323 expansion_config.revision, 324 expansion_config.fab_revision); 325 setenv("defaultdisplay", "lcd43"); 326 break; 327 case ETTUS_USRP_E: 328 printf("Recognized Ettus Research USRP-E (rev %d %s)\n", 329 expansion_config.revision, 330 expansion_config.fab_revision); 331 MUX_USRP_E(); 332 setenv("defaultdisplay", "dvi"); 333 break; 334 case GUMSTIX_NO_EEPROM: 335 puts("No EEPROM on expansion board\n"); 336 break; 337 default: 338 puts("Unrecognized expansion board\n"); 339 } 340 341 if (expansion_config.content == 1) 342 setenv(expansion_config.env_var, expansion_config.env_setting); 343 344 dieid_num_r(); 345 346 return 0; 347 } 348 349 /* 350 * Routine: set_muxconf_regs 351 * Description: Setting up the configuration Mux registers specific to the 352 * hardware. Many pins need to be moved from protect to primary 353 * mode. 354 */ 355 void set_muxconf_regs(void) 356 { 357 MUX_OVERO(); 358 } 359 360 #if defined(CONFIG_CMD_NET) 361 /* 362 * Routine: setup_net_chip 363 * Description: Setting up the configuration GPMC registers specific to the 364 * Ethernet hardware. 365 */ 366 static void setup_net_chip(void) 367 { 368 struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE; 369 370 /* first lan chip */ 371 enable_gpmc_cs_config(gpmc_lan_config, &gpmc_cfg->cs[5], 0x2C000000, 372 GPMC_SIZE_16M); 373 374 /* Enable off mode for NWE in PADCONF_GPMC_NWE register */ 375 writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe); 376 /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */ 377 writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe); 378 /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */ 379 writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00, 380 &ctrl_base->gpmc_nadv_ale); 381 382 /* Make GPIO 64 as output pin and send a magic pulse through it */ 383 if (!gpio_request(64, "")) { 384 gpio_direction_output(64, 0); 385 gpio_set_value(64, 1); 386 udelay(1); 387 gpio_set_value(64, 0); 388 udelay(1); 389 gpio_set_value(64, 1); 390 } 391 } 392 #endif 393 394 int board_eth_init(bd_t *bis) 395 { 396 int rc = 0; 397 #ifdef CONFIG_SMC911X 398 rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); 399 #endif 400 return rc; 401 } 402 403 #if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD) 404 int board_mmc_init(bd_t *bis) 405 { 406 omap_mmc_init(0); 407 return 0; 408 } 409 #endif 410