1 /* 2 * Maintainer : Steve Sakoman <steve@sakoman.com> 3 * 4 * Derived from Beagle Board, 3430 SDP, and OMAP3EVM code by 5 * Richard Woodruff <r-woodruff2@ti.com> 6 * Syed Mohammed Khasim <khasim@ti.com> 7 * Sunil Kumar <sunilsaini05@gmail.com> 8 * Shashi Ranjan <shashiranjanmca05@gmail.com> 9 * 10 * (C) Copyright 2004-2008 11 * Texas Instruments, <www.ti.com> 12 * 13 * See file CREDITS for list of people who contributed to this 14 * project. 15 * 16 * This program is free software; you can redistribute it and/or 17 * modify it under the terms of the GNU General Public License as 18 * published by the Free Software Foundation; either version 2 of 19 * the License, or (at your option) any later version. 20 * 21 * This program is distributed in the hope that it will be useful, 22 * but WITHOUT ANY WARRANTY; without even the implied warranty of 23 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 24 * GNU General Public License for more details. 25 * 26 * You should have received a copy of the GNU General Public License 27 * along with this program; if not, write to the Free Software 28 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 29 * MA 02111-1307 USA 30 */ 31 #include <common.h> 32 #include <netdev.h> 33 #include <twl4030.h> 34 #include <linux/mtd/nand.h> 35 #include <asm/io.h> 36 #include <asm/arch/mmc_host_def.h> 37 #include <asm/arch/mux.h> 38 #include <asm/arch/mem.h> 39 #include <asm/arch/sys_proto.h> 40 #include <asm/arch/omap_gpmc.h> 41 #include <asm/gpio.h> 42 #include <asm/mach-types.h> 43 #include "overo.h" 44 45 DECLARE_GLOBAL_DATA_PTR; 46 47 #define TWL4030_I2C_BUS 0 48 #define EXPANSION_EEPROM_I2C_BUS 2 49 #define EXPANSION_EEPROM_I2C_ADDRESS 0x51 50 51 #define GUMSTIX_SUMMIT 0x01000200 52 #define GUMSTIX_TOBI 0x02000200 53 #define GUMSTIX_TOBI_DUO 0x03000200 54 #define GUMSTIX_PALO35 0x04000200 55 #define GUMSTIX_PALO43 0x05000200 56 #define GUMSTIX_CHESTNUT43 0x06000200 57 #define GUMSTIX_PINTO 0x07000200 58 #define GUMSTIX_GALLOP43 0x08000200 59 60 #define ETTUS_USRP_E 0x01000300 61 62 #define GUMSTIX_NO_EEPROM 0xffffffff 63 64 static struct { 65 unsigned int device_vendor; 66 unsigned char revision; 67 unsigned char content; 68 char fab_revision[8]; 69 char env_var[16]; 70 char env_setting[64]; 71 } expansion_config; 72 73 #if defined(CONFIG_CMD_NET) 74 static void setup_net_chip(void); 75 #endif 76 77 /* GPMC definitions for LAN9221 chips on Tobi expansion boards */ 78 static const u32 gpmc_lan_config[] = { 79 NET_LAN9221_GPMC_CONFIG1, 80 NET_LAN9221_GPMC_CONFIG2, 81 NET_LAN9221_GPMC_CONFIG3, 82 NET_LAN9221_GPMC_CONFIG4, 83 NET_LAN9221_GPMC_CONFIG5, 84 NET_LAN9221_GPMC_CONFIG6, 85 /*CONFIG7- computed as params */ 86 }; 87 88 /* 89 * Routine: board_init 90 * Description: Early hardware init. 91 */ 92 int board_init(void) 93 { 94 gpmc_init(); /* in SRAM or SDRAM, finish GPMC */ 95 /* board id for Linux */ 96 gd->bd->bi_arch_number = MACH_TYPE_OVERO; 97 /* boot param addr */ 98 gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); 99 100 return 0; 101 } 102 103 /* 104 * Routine: get_board_revision 105 * Description: Returns the board revision 106 */ 107 int get_board_revision(void) 108 { 109 int revision; 110 111 #ifdef CONFIG_DRIVER_OMAP34XX_I2C 112 unsigned char data; 113 114 /* board revisions <= R2410 connect 4030 irq_1 to gpio112 */ 115 /* these boards should return a revision number of 0 */ 116 /* the code below forces a 4030 RTC irq to ensure that gpio112 is low */ 117 i2c_set_bus_num(TWL4030_I2C_BUS); 118 data = 0x01; 119 i2c_write(0x4B, 0x29, 1, &data, 1); 120 data = 0x0c; 121 i2c_write(0x4B, 0x2b, 1, &data, 1); 122 i2c_read(0x4B, 0x2a, 1, &data, 1); 123 #endif 124 125 if (!gpio_request(112, "") && 126 !gpio_request(113, "") && 127 !gpio_request(115, "")) { 128 129 gpio_direction_input(112); 130 gpio_direction_input(113); 131 gpio_direction_input(115); 132 133 revision = gpio_get_value(115) << 2 | 134 gpio_get_value(113) << 1 | 135 gpio_get_value(112); 136 } else { 137 puts("Error: unable to acquire board revision GPIOs\n"); 138 revision = -1; 139 } 140 141 return revision; 142 } 143 144 #ifdef CONFIG_SPL_BUILD 145 /* 146 * Routine: get_board_mem_timings 147 * Description: If we use SPL then there is no x-loader nor config header 148 * so we have to setup the DDR timings ourself on both banks. 149 */ 150 void get_board_mem_timings(struct board_sdrc_timings *timings) 151 { 152 timings->mr = MICRON_V_MR_165; 153 switch (get_board_revision()) { 154 case REVISION_0: /* Micron 1286MB/256MB, 1/2 banks of 128MB */ 155 timings->mcfg = MICRON_V_MCFG_165(128 << 20); 156 timings->ctrla = MICRON_V_ACTIMA_165; 157 timings->ctrlb = MICRON_V_ACTIMB_165; 158 timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 159 break; 160 case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */ 161 timings->mcfg = MICRON_V_MCFG_165(256 << 20); 162 timings->ctrla = MICRON_V_ACTIMA_165; 163 timings->ctrlb = MICRON_V_ACTIMB_165; 164 timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 165 break; 166 case REVISION_2: /* Hynix 256MB/512MB, 1/2 banks of 256MB */ 167 timings->mcfg = HYNIX_V_MCFG_165(256 << 20); 168 timings->ctrla = HYNIX_V_ACTIMA_165; 169 timings->ctrlb = HYNIX_V_ACTIMB_165; 170 timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 171 break; 172 default: 173 timings->mcfg = MICRON_V_MCFG_165(128 << 20); 174 timings->ctrla = MICRON_V_ACTIMA_165; 175 timings->ctrlb = MICRON_V_ACTIMB_165; 176 timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; 177 } 178 } 179 #endif 180 181 /* 182 * Routine: get_sdio2_config 183 * Description: Return information about the wifi module connection 184 * Returns 0 if the module connects though a level translator 185 * Returns 1 if the module connects directly 186 */ 187 int get_sdio2_config(void) 188 { 189 int sdio_direct; 190 191 if (!gpio_request(130, "") && !gpio_request(139, "")) { 192 193 gpio_direction_output(130, 0); 194 gpio_direction_input(139); 195 196 sdio_direct = 1; 197 gpio_set_value(130, 0); 198 if (gpio_get_value(139) == 0) { 199 gpio_set_value(130, 1); 200 if (gpio_get_value(139) == 1) 201 sdio_direct = 0; 202 } 203 204 gpio_direction_input(130); 205 } else { 206 puts("Error: unable to acquire sdio2 clk GPIOs\n"); 207 sdio_direct = -1; 208 } 209 210 return sdio_direct; 211 } 212 213 /* 214 * Routine: get_expansion_id 215 * Description: This function checks for expansion board by checking I2C 216 * bus 2 for the availability of an AT24C01B serial EEPROM. 217 * returns the device_vendor field from the EEPROM 218 */ 219 unsigned int get_expansion_id(void) 220 { 221 i2c_set_bus_num(EXPANSION_EEPROM_I2C_BUS); 222 223 /* return GUMSTIX_NO_EEPROM if eeprom doesn't respond */ 224 if (i2c_probe(EXPANSION_EEPROM_I2C_ADDRESS) == 1) { 225 i2c_set_bus_num(TWL4030_I2C_BUS); 226 return GUMSTIX_NO_EEPROM; 227 } 228 229 /* read configuration data */ 230 i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 1, (u8 *)&expansion_config, 231 sizeof(expansion_config)); 232 233 i2c_set_bus_num(TWL4030_I2C_BUS); 234 235 return expansion_config.device_vendor; 236 } 237 238 /* 239 * Routine: misc_init_r 240 * Description: Configure board specific parts 241 */ 242 int misc_init_r(void) 243 { 244 twl4030_power_init(); 245 twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON); 246 247 #if defined(CONFIG_CMD_NET) 248 setup_net_chip(); 249 #endif 250 251 printf("Board revision: %d\n", get_board_revision()); 252 253 switch (get_sdio2_config()) { 254 case 0: 255 puts("Tranceiver detected on mmc2\n"); 256 MUX_OVERO_SDIO2_TRANSCEIVER(); 257 break; 258 case 1: 259 puts("Direct connection on mmc2\n"); 260 MUX_OVERO_SDIO2_DIRECT(); 261 break; 262 default: 263 puts("Unable to detect mmc2 connection type\n"); 264 } 265 266 switch (get_expansion_id()) { 267 case GUMSTIX_SUMMIT: 268 printf("Recognized Summit expansion board (rev %d %s)\n", 269 expansion_config.revision, 270 expansion_config.fab_revision); 271 setenv("defaultdisplay", "dvi"); 272 break; 273 case GUMSTIX_TOBI: 274 printf("Recognized Tobi expansion board (rev %d %s)\n", 275 expansion_config.revision, 276 expansion_config.fab_revision); 277 setenv("defaultdisplay", "dvi"); 278 break; 279 case GUMSTIX_TOBI_DUO: 280 printf("Recognized Tobi Duo expansion board (rev %d %s)\n", 281 expansion_config.revision, 282 expansion_config.fab_revision); 283 /* second lan chip */ 284 enable_gpmc_cs_config(gpmc_lan_config, &gpmc_cfg->cs[4], 285 0x2B000000, GPMC_SIZE_16M); 286 break; 287 case GUMSTIX_PALO35: 288 printf("Recognized Palo35 expansion board (rev %d %s)\n", 289 expansion_config.revision, 290 expansion_config.fab_revision); 291 setenv("defaultdisplay", "lcd35"); 292 break; 293 case GUMSTIX_PALO43: 294 printf("Recognized Palo43 expansion board (rev %d %s)\n", 295 expansion_config.revision, 296 expansion_config.fab_revision); 297 setenv("defaultdisplay", "lcd43"); 298 break; 299 case GUMSTIX_CHESTNUT43: 300 printf("Recognized Chestnut43 expansion board (rev %d %s)\n", 301 expansion_config.revision, 302 expansion_config.fab_revision); 303 setenv("defaultdisplay", "lcd43"); 304 break; 305 case GUMSTIX_PINTO: 306 printf("Recognized Pinto expansion board (rev %d %s)\n", 307 expansion_config.revision, 308 expansion_config.fab_revision); 309 break; 310 case GUMSTIX_GALLOP43: 311 printf("Recognized Gallop43 expansion board (rev %d %s)\n", 312 expansion_config.revision, 313 expansion_config.fab_revision); 314 setenv("defaultdisplay", "lcd43"); 315 break; 316 case ETTUS_USRP_E: 317 printf("Recognized Ettus Research USRP-E (rev %d %s)\n", 318 expansion_config.revision, 319 expansion_config.fab_revision); 320 MUX_USRP_E(); 321 setenv("defaultdisplay", "dvi"); 322 break; 323 case GUMSTIX_NO_EEPROM: 324 puts("No EEPROM on expansion board\n"); 325 break; 326 default: 327 puts("Unrecognized expansion board\n"); 328 } 329 330 if (expansion_config.content == 1) 331 setenv(expansion_config.env_var, expansion_config.env_setting); 332 333 dieid_num_r(); 334 335 return 0; 336 } 337 338 /* 339 * Routine: set_muxconf_regs 340 * Description: Setting up the configuration Mux registers specific to the 341 * hardware. Many pins need to be moved from protect to primary 342 * mode. 343 */ 344 void set_muxconf_regs(void) 345 { 346 MUX_OVERO(); 347 } 348 349 #if defined(CONFIG_CMD_NET) 350 /* 351 * Routine: setup_net_chip 352 * Description: Setting up the configuration GPMC registers specific to the 353 * Ethernet hardware. 354 */ 355 static void setup_net_chip(void) 356 { 357 struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE; 358 359 /* first lan chip */ 360 enable_gpmc_cs_config(gpmc_lan_config, &gpmc_cfg->cs[5], 0x2C000000, 361 GPMC_SIZE_16M); 362 363 /* Enable off mode for NWE in PADCONF_GPMC_NWE register */ 364 writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe); 365 /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */ 366 writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe); 367 /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */ 368 writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00, 369 &ctrl_base->gpmc_nadv_ale); 370 371 /* Make GPIO 64 as output pin and send a magic pulse through it */ 372 if (!gpio_request(64, "")) { 373 gpio_direction_output(64, 0); 374 gpio_set_value(64, 1); 375 udelay(1); 376 gpio_set_value(64, 0); 377 udelay(1); 378 gpio_set_value(64, 1); 379 } 380 } 381 #endif 382 383 int board_eth_init(bd_t *bis) 384 { 385 int rc = 0; 386 #ifdef CONFIG_SMC911X 387 rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); 388 #endif 389 return rc; 390 } 391 392 #if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD) 393 int board_mmc_init(bd_t *bis) 394 { 395 omap_mmc_init(0, 0, 0); 396 return 0; 397 } 398 #endif 399