1 /* 2 * Board functions for mini-box PICOSAM9G45 (AT91SAM9G45) based board 3 * (C) Copyright 2015 Inter Act B.V. 4 * 5 * Based on: 6 * U-Boot file: board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c 7 * (C) Copyright 2007-2008 8 * Stelian Pop <stelian@popies.net> 9 * Lead Tech Design <www.leadtechdesign.com> 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14 #include <common.h> 15 #include <asm/io.h> 16 #include <asm/arch/clk.h> 17 #include <asm/arch/at91sam9g45_matrix.h> 18 #include <asm/arch/at91sam9_smc.h> 19 #include <asm/arch/at91_common.h> 20 #include <asm/arch/at91_pmc.h> 21 #include <asm/arch/gpio.h> 22 #include <asm/arch/clk.h> 23 #include <lcd.h> 24 #include <linux/mtd/nand.h> 25 #include <atmel_lcdc.h> 26 #include <atmel_mci.h> 27 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) 28 #include <net.h> 29 #endif 30 #include <netdev.h> 31 32 DECLARE_GLOBAL_DATA_PTR; 33 34 /* ------------------------------------------------------------------------- */ 35 /* 36 * Miscelaneous platform dependent initialisations 37 */ 38 39 #if defined(CONFIG_SPL_BUILD) 40 #include <spl.h> 41 42 void at91_spl_board_init(void) 43 { 44 #ifdef CONFIG_SYS_USE_MMC 45 at91_mci_hw_init(); 46 #endif 47 } 48 49 #include <asm/arch/atmel_mpddrc.h> 50 static void ddr2_conf(struct atmel_mpddr *ddr2) 51 { 52 ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM); 53 54 ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 | 55 ATMEL_MPDDRC_CR_NR_ROW_14 | 56 ATMEL_MPDDRC_CR_DQMS_SHARED | 57 ATMEL_MPDDRC_CR_CAS_DDR_CAS3); 58 59 ddr2->rtr = 0x24b; 60 61 ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */ 62 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */ 63 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */ 64 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */ 65 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */ 66 1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/ 67 1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */ 68 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */ 69 70 ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */ 71 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET | 72 16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET | 73 14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET); 74 75 ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET | 76 0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET | 77 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET | 78 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET); 79 } 80 81 void mem_init(void) 82 { 83 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 84 struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX; 85 struct atmel_mpddr ddr2; 86 unsigned long csa; 87 88 ddr2_conf(&ddr2); 89 90 /* enable DDR2 clock */ 91 writel(AT91_PMC_DDR, &pmc->scer); 92 93 /* Chip select 1 is for DDR2/SDRAM */ 94 csa = readl(&mat->ebicsa); 95 csa |= AT91_MATRIX_EBI_CS1A_SDRAMC; 96 csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V; 97 writel(csa, &mat->ebicsa); 98 99 /* DDRAM2 Controller initialize */ 100 ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2); 101 ddr2_init(ATMEL_BASE_DDRSDRC1, ATMEL_BASE_CS1, &ddr2); 102 } 103 #endif 104 105 #ifdef CONFIG_CMD_USB 106 static void picosam9g45_usb_hw_init(void) 107 { 108 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 109 110 writel(1 << ATMEL_ID_PIODE, &pmc->pcer); 111 112 at91_set_gpio_output(AT91_PIN_PD1, 0); 113 at91_set_gpio_output(AT91_PIN_PD3, 0); 114 } 115 #endif 116 117 #ifdef CONFIG_MACB 118 static void picosam9g45_macb_hw_init(void) 119 { 120 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 121 struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; 122 123 /* Enable clock */ 124 writel(1 << ATMEL_ID_EMAC, &pmc->pcer); 125 126 /* 127 * Disable pull-up on: 128 * RXDV (PA15) => PHY normal mode (not Test mode) 129 * ERX0 (PA12) => PHY ADDR0 130 * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0 131 * 132 * PHY has internal pull-down 133 */ 134 writel(pin_to_mask(AT91_PIN_PA15) | 135 pin_to_mask(AT91_PIN_PA12) | 136 pin_to_mask(AT91_PIN_PA13), 137 &pioa->pudr); 138 139 at91_phy_reset(); 140 141 /* Re-enable pull-up */ 142 writel(pin_to_mask(AT91_PIN_PA15) | 143 pin_to_mask(AT91_PIN_PA12) | 144 pin_to_mask(AT91_PIN_PA13), 145 &pioa->puer); 146 147 /* And the pins. */ 148 at91_macb_hw_init(); 149 } 150 #endif 151 152 #ifdef CONFIG_LCD 153 154 vidinfo_t panel_info = { 155 .vl_col = 480, 156 .vl_row = 272, 157 .vl_clk = 9000000, 158 .vl_sync = ATMEL_LCDC_INVLINE_NORMAL | 159 ATMEL_LCDC_INVFRAME_NORMAL, 160 .vl_bpix = 3, 161 .vl_tft = 1, 162 .vl_hsync_len = 45, 163 .vl_left_margin = 1, 164 .vl_right_margin = 1, 165 .vl_vsync_len = 1, 166 .vl_upper_margin = 40, 167 .vl_lower_margin = 1, 168 .mmio = ATMEL_BASE_LCDC, 169 }; 170 171 172 void lcd_enable(void) 173 { 174 at91_set_A_periph(AT91_PIN_PE6, 1); /* power up */ 175 } 176 177 void lcd_disable(void) 178 { 179 at91_set_A_periph(AT91_PIN_PE6, 0); /* power down */ 180 } 181 182 static void picosam9g45_lcd_hw_init(void) 183 { 184 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 185 186 at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */ 187 at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */ 188 at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */ 189 at91_set_A_periph(AT91_PIN_PE4, 0); /* LCDHSYNC */ 190 at91_set_A_periph(AT91_PIN_PE5, 0); /* LCDDOTCK */ 191 192 at91_set_A_periph(AT91_PIN_PE7, 0); /* LCDD0 */ 193 at91_set_A_periph(AT91_PIN_PE8, 0); /* LCDD1 */ 194 at91_set_A_periph(AT91_PIN_PE9, 0); /* LCDD2 */ 195 at91_set_A_periph(AT91_PIN_PE10, 0); /* LCDD3 */ 196 at91_set_A_periph(AT91_PIN_PE11, 0); /* LCDD4 */ 197 at91_set_A_periph(AT91_PIN_PE12, 0); /* LCDD5 */ 198 at91_set_A_periph(AT91_PIN_PE13, 0); /* LCDD6 */ 199 at91_set_A_periph(AT91_PIN_PE14, 0); /* LCDD7 */ 200 at91_set_A_periph(AT91_PIN_PE15, 0); /* LCDD8 */ 201 at91_set_A_periph(AT91_PIN_PE16, 0); /* LCDD9 */ 202 at91_set_A_periph(AT91_PIN_PE17, 0); /* LCDD10 */ 203 at91_set_A_periph(AT91_PIN_PE18, 0); /* LCDD11 */ 204 at91_set_A_periph(AT91_PIN_PE19, 0); /* LCDD12 */ 205 at91_set_B_periph(AT91_PIN_PE20, 0); /* LCDD13 */ 206 at91_set_A_periph(AT91_PIN_PE21, 0); /* LCDD14 */ 207 at91_set_A_periph(AT91_PIN_PE22, 0); /* LCDD15 */ 208 at91_set_A_periph(AT91_PIN_PE23, 0); /* LCDD16 */ 209 at91_set_A_periph(AT91_PIN_PE24, 0); /* LCDD17 */ 210 at91_set_A_periph(AT91_PIN_PE25, 0); /* LCDD18 */ 211 at91_set_A_periph(AT91_PIN_PE26, 0); /* LCDD19 */ 212 at91_set_A_periph(AT91_PIN_PE27, 0); /* LCDD20 */ 213 at91_set_B_periph(AT91_PIN_PE28, 0); /* LCDD21 */ 214 at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */ 215 at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */ 216 217 writel(1 << ATMEL_ID_LCDC, &pmc->pcer); 218 219 gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE; 220 } 221 222 #ifdef CONFIG_LCD_INFO 223 #include <nand.h> 224 #include <version.h> 225 226 void lcd_show_board_info(void) 227 { 228 ulong dram_size; 229 int i; 230 char temp[32]; 231 232 lcd_printf("%s\n", U_BOOT_VERSION); 233 lcd_printf("(C) 2015 Inter Act B.V.\n"); 234 lcd_printf("support@interact.nl\n"); 235 lcd_printf("%s CPU at %s MHz\n", 236 ATMEL_CPU_NAME, 237 strmhz(temp, get_cpu_clk_rate())); 238 239 dram_size = 0; 240 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) 241 dram_size += gd->bd->bi_dram[i].size; 242 lcd_printf(" %ld MB SDRAM\n", dram_size >> 20); 243 } 244 #endif /* CONFIG_LCD_INFO */ 245 #endif 246 247 #ifdef CONFIG_GENERIC_ATMEL_MCI 248 int board_mmc_init(bd_t *bis) 249 { 250 at91_mci_hw_init(); 251 252 return atmel_mci_init((void *)ATMEL_BASE_MCI0); 253 } 254 #endif 255 256 int board_early_init_f(void) 257 { 258 at91_seriald_hw_init(); 259 return 0; 260 } 261 262 int board_init(void) 263 { 264 gd->bd->bi_arch_number = MACH_TYPE_PICOSAM9G45; 265 266 /* adress of boot parameters */ 267 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 268 269 #ifdef CONFIG_CMD_USB 270 picosam9g45_usb_hw_init(); 271 #endif 272 #ifdef CONFIG_HAS_DATAFLASH 273 at91_spi0_hw_init(1 << 0); 274 #endif 275 #ifdef CONFIG_ATMEL_SPI 276 at91_spi0_hw_init(1 << 4); 277 #endif 278 #ifdef CONFIG_MACB 279 picosam9g45_macb_hw_init(); 280 #endif 281 #ifdef CONFIG_LCD 282 picosam9g45_lcd_hw_init(); 283 #endif 284 return 0; 285 } 286 287 int dram_init(void) 288 { 289 gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) 290 + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE); 291 292 return 0; 293 } 294 295 void dram_init_banksize(void) 296 { 297 gd->bd->bi_dram[0].start = PHYS_SDRAM_1; 298 gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, 299 PHYS_SDRAM_1_SIZE); 300 gd->bd->bi_dram[1].start = PHYS_SDRAM_2; 301 gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, 302 PHYS_SDRAM_2_SIZE); 303 } 304 305 #ifdef CONFIG_RESET_PHY_R 306 void reset_phy(void) 307 { 308 } 309 #endif 310 311 int board_eth_init(bd_t *bis) 312 { 313 int rc = 0; 314 #ifdef CONFIG_MACB 315 rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00); 316 #endif 317 return rc; 318 } 319 320 /* SPI chip select control */ 321 #ifdef CONFIG_ATMEL_SPI 322 #include <spi.h> 323 324 int spi_cs_is_valid(unsigned int bus, unsigned int cs) 325 { 326 return bus == 0 && cs < 2; 327 } 328 329 void spi_cs_activate(struct spi_slave *slave) 330 { 331 switch (slave->cs) { 332 case 1: 333 at91_set_gpio_output(AT91_PIN_PB18, 0); 334 break; 335 case 0: 336 default: 337 at91_set_gpio_output(AT91_PIN_PB3, 0); 338 break; 339 } 340 } 341 342 void spi_cs_deactivate(struct spi_slave *slave) 343 { 344 switch (slave->cs) { 345 case 1: 346 at91_set_gpio_output(AT91_PIN_PB18, 1); 347 break; 348 case 0: 349 default: 350 at91_set_gpio_output(AT91_PIN_PB3, 1); 351 break; 352 } 353 } 354 #endif /* CONFIG_ATMEL_SPI */ 355