1 /* 2 * (C) Copyright 2013 Keymile AG 3 * Valentin Longchamp <valentin.longchamp@keymile.com> 4 * 5 * Copyright 2011,2012 Freescale Semiconductor, Inc. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #include <common.h> 11 #include <command.h> 12 #include <netdev.h> 13 #include <linux/compiler.h> 14 #include <asm/mmu.h> 15 #include <asm/processor.h> 16 #include <asm/cache.h> 17 #include <asm/immap_85xx.h> 18 #include <asm/fsl_law.h> 19 #include <asm/fsl_serdes.h> 20 #include <asm/fsl_portals.h> 21 #include <asm/fsl_liodn.h> 22 #include <fm_eth.h> 23 24 #include "../common/common.h" 25 #include "kmp204x.h" 26 27 DECLARE_GLOBAL_DATA_PTR; 28 29 static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; 30 31 int checkboard(void) 32 { 33 printf("Board: Keymile %s\n", CONFIG_KM_BOARD_NAME); 34 35 return 0; 36 } 37 38 /* I2C deblocking uses the algorithm defined in board/keymile/common/common.c 39 * 2 dedicated QRIO GPIOs externally pull the SCL and SDA lines 40 * For I2C only the low state is activly driven and high state is pulled-up 41 * by a resistor. Therefore the deblock GPIOs are used 42 * -> as an active output to drive a low state 43 * -> as an open-drain input to have a pulled-up high state 44 */ 45 46 /* QRIO GPIOs used for deblocking */ 47 #define DEBLOCK_PORT1 GPIO_A 48 #define DEBLOCK_SCL1 20 49 #define DEBLOCK_SDA1 21 50 51 /* By default deblock GPIOs are floating */ 52 static void i2c_deblock_gpio_cfg(void) 53 { 54 /* set I2C bus 1 deblocking GPIOs input, but 0 value for open drain */ 55 qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SCL1); 56 qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SDA1); 57 58 qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, 0); 59 qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, 0); 60 } 61 62 void set_sda(int state) 63 { 64 qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, state); 65 } 66 67 void set_scl(int state) 68 { 69 qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, state); 70 } 71 72 int get_sda(void) 73 { 74 return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1); 75 } 76 77 int get_scl(void) 78 { 79 return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1); 80 } 81 82 83 #define ZL30158_RST 8 84 #define BFTIC4_RST 0 85 #define RSTRQSR1_WDT_RR 0x00200000 86 #define RSTRQSR1_SW_RR 0x00100000 87 88 int board_early_init_f(void) 89 { 90 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 91 bool cpuwd_flag = false; 92 93 /* configure mode for uP reset request */ 94 qrio_uprstreq(UPREQ_CORE_RST); 95 96 /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */ 97 setbits_be32(&gur->ddrclkdr, 0x001f000f); 98 99 /* set reset reason according CPU register */ 100 if ((gur->rstrqsr1 & (RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR)) == 101 RSTRQSR1_WDT_RR) 102 cpuwd_flag = true; 103 104 qrio_cpuwd_flag(cpuwd_flag); 105 /* clear CPU bits by writing 1 */ 106 setbits_be32(&gur->rstrqsr1, RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR); 107 108 /* set the BFTIC's prstcfg to reset at power-up and unit reset only */ 109 qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST); 110 /* and enable WD on it */ 111 qrio_wdmask(BFTIC4_RST, true); 112 113 /* set the ZL30138's prstcfg to reset at power-up only */ 114 qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST); 115 /* and take it out of reset as soon as possible (needed for Hooper) */ 116 qrio_prst(ZL30158_RST, false, false); 117 118 return 0; 119 } 120 121 int board_early_init_r(void) 122 { 123 int ret = 0; 124 /* Flush d-cache and invalidate i-cache of any FLASH data */ 125 flush_dcache(); 126 invalidate_icache(); 127 128 set_liodns(); 129 setup_portals(); 130 131 ret = trigger_fpga_config(); 132 if (ret) 133 printf("error triggering PCIe FPGA config\n"); 134 135 /* enable the Unit LED (red) & Boot LED (on) */ 136 qrio_set_leds(); 137 138 /* enable Application Buffer */ 139 qrio_enable_app_buffer(); 140 141 return ret; 142 } 143 144 unsigned long get_board_sys_clk(unsigned long dummy) 145 { 146 return 66666666; 147 } 148 149 #define ETH_FRONT_PHY_RST 15 150 #define QSFP2_RST 11 151 #define QSFP1_RST 10 152 #define ZL30343_RST 9 153 154 int misc_init_f(void) 155 { 156 /* configure QRIO pis for i2c deblocking */ 157 i2c_deblock_gpio_cfg(); 158 159 /* configure the front phy's prstcfg and take it out of reset */ 160 qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST); 161 qrio_prst(ETH_FRONT_PHY_RST, false, false); 162 163 /* set the ZL30343 prstcfg to reset at power-up only */ 164 qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST); 165 /* and enable the WD on it */ 166 qrio_wdmask(ZL30343_RST, true); 167 168 /* set the QSFPs' prstcfg to reset at power-up and unit rst only */ 169 qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST); 170 qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST); 171 172 /* and enable the WD on them */ 173 qrio_wdmask(QSFP1_RST, true); 174 qrio_wdmask(QSFP2_RST, true); 175 176 return 0; 177 } 178 179 #define NUM_SRDS_BANKS 2 180 181 int misc_init_r(void) 182 { 183 serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; 184 u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100, 185 SRDS_PLLCR0_RFCK_SEL_125}; 186 unsigned int i; 187 188 /* check SERDES reference clocks */ 189 for (i = 0; i < NUM_SRDS_BANKS; i++) { 190 u32 actual = in_be32(®s->bank[i].pllcr0); 191 actual &= SRDS_PLLCR0_RFCK_SEL_MASK; 192 if (actual != expected[i]) { 193 printf("Warning: SERDES bank %u expects reference \ 194 clock %sMHz, but actual is %sMHz\n", i + 1, 195 serdes_clock_to_string(expected[i]), 196 serdes_clock_to_string(actual)); 197 } 198 } 199 200 ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); 201 return 0; 202 } 203 204 #if defined(CONFIG_HUSH_INIT_VAR) 205 int hush_init_var(void) 206 { 207 ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); 208 return 0; 209 } 210 #endif 211 212 #if defined(CONFIG_LAST_STAGE_INIT) 213 214 int last_stage_init(void) 215 { 216 #if defined(CONFIG_KMCOGE4) 217 /* on KMCOGE4, the BFTIC4 is on the LBAPP2 */ 218 struct bfticu_iomap *bftic4 = 219 (struct bfticu_iomap *)CONFIG_SYS_LBAPP2_BASE; 220 u8 dip_switch = in_8((u8 *)&(bftic4->mswitch)) & BFTICU_DIPSWITCH_MASK; 221 222 if (dip_switch != 0) { 223 /* start bootloader */ 224 puts("DIP: Enabled\n"); 225 env_set("actual_bank", "0"); 226 } 227 #endif 228 set_km_env(); 229 230 return 0; 231 } 232 #endif 233 234 #ifdef CONFIG_SYS_DPAA_FMAN 235 void fdt_fixup_fman_mac_addresses(void *blob) 236 { 237 int node, i, ret; 238 char *tmp, *end; 239 unsigned char mac_addr[6]; 240 241 /* get the mac addr from env */ 242 tmp = env_get("ethaddr"); 243 if (!tmp) { 244 printf("ethaddr env variable not defined\n"); 245 return; 246 } 247 for (i = 0; i < 6; i++) { 248 mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0; 249 if (tmp) 250 tmp = (*end) ? end+1 : end; 251 } 252 253 /* find the correct fdt ethernet path and correct it */ 254 node = fdt_path_offset(blob, "/soc/fman/ethernet@e8000"); 255 if (node < 0) { 256 printf("no /soc/fman/ethernet path offset\n"); 257 return; 258 } 259 ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6); 260 if (ret) { 261 printf("error setting local-mac-address property\n"); 262 return; 263 } 264 } 265 #endif 266 267 int ft_board_setup(void *blob, bd_t *bd) 268 { 269 phys_addr_t base; 270 phys_size_t size; 271 272 ft_cpu_setup(blob, bd); 273 274 base = env_get_bootm_low(); 275 size = env_get_bootm_size(); 276 277 fdt_fixup_memory(blob, (u64)base, (u64)size); 278 279 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 280 fsl_fdt_fixup_dr_usb(blob, bd); 281 #endif 282 283 #ifdef CONFIG_PCI 284 pci_of_setup(blob, bd); 285 #endif 286 287 fdt_fixup_liodn(blob); 288 #ifdef CONFIG_SYS_DPAA_FMAN 289 fdt_fixup_fman_ethernet(blob); 290 fdt_fixup_fman_mac_addresses(blob); 291 #endif 292 293 return 0; 294 } 295 296 #if defined(CONFIG_POST) 297 298 /* DIC26_SELFTEST GPIO used to start factory test sw */ 299 #define SELFTEST_PORT GPIO_A 300 #define SELFTEST_PIN 31 301 302 int post_hotkeys_pressed(void) 303 { 304 qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN); 305 return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN); 306 } 307 #endif 308