1 /* 2 * (C) Copyright 2013 Keymile AG 3 * Valentin Longchamp <valentin.longchamp@keymile.com> 4 * 5 * Copyright 2011,2012 Freescale Semiconductor, Inc. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #include <common.h> 11 #include <command.h> 12 #include <netdev.h> 13 #include <linux/compiler.h> 14 #include <asm/mmu.h> 15 #include <asm/processor.h> 16 #include <asm/cache.h> 17 #include <asm/immap_85xx.h> 18 #include <asm/fsl_law.h> 19 #include <asm/fsl_serdes.h> 20 #include <asm/fsl_portals.h> 21 #include <asm/fsl_liodn.h> 22 #include <fm_eth.h> 23 24 #include "../common/common.h" 25 #include "kmp204x.h" 26 27 DECLARE_GLOBAL_DATA_PTR; 28 29 int checkboard(void) 30 { 31 printf("Board: Keymile %s\n", CONFIG_KM_BOARD_NAME); 32 33 return 0; 34 } 35 36 /* I2C deblocking uses the algorithm defined in board/keymile/common/common.c 37 * 2 dedicated QRIO GPIOs externally pull the SCL and SDA lines 38 * For I2C only the low state is activly driven and high state is pulled-up 39 * by a resistor. Therefore the deblock GPIOs are used 40 * -> as an active output to drive a low state 41 * -> as an open-drain input to have a pulled-up high state 42 */ 43 44 /* QRIO GPIOs used for deblocking */ 45 #define DEBLOCK_PORT1 GPIO_A 46 #define DEBLOCK_SCL1 20 47 #define DEBLOCK_SDA1 21 48 49 /* By default deblock GPIOs are floating */ 50 static void i2c_deblock_gpio_cfg(void) 51 { 52 /* set I2C bus 1 deblocking GPIOs input, but 0 value for open drain */ 53 qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SCL1); 54 qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SDA1); 55 56 qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, 0); 57 qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, 0); 58 } 59 60 void set_sda(int state) 61 { 62 qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, state); 63 } 64 65 void set_scl(int state) 66 { 67 qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, state); 68 } 69 70 int get_sda(void) 71 { 72 return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1); 73 } 74 75 int get_scl(void) 76 { 77 return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1); 78 } 79 80 81 #define ZL30158_RST 8 82 #define ZL30343_RST 9 83 84 int board_early_init_f(void) 85 { 86 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 87 88 /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */ 89 setbits_be32(&gur->ddrclkdr, 0x001f000f); 90 91 /* take the Zarlinks out of reset as soon as possible */ 92 qrio_prst(ZL30158_RST, false, false); 93 qrio_prst(ZL30343_RST, false, false); 94 95 /* and set their reset to power-up only */ 96 qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST); 97 qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST); 98 99 return 0; 100 } 101 102 int board_early_init_r(void) 103 { 104 /* Flush d-cache and invalidate i-cache of any FLASH data */ 105 flush_dcache(); 106 invalidate_icache(); 107 108 set_liodns(); 109 setup_portals(); 110 111 return 0; 112 } 113 114 unsigned long get_board_sys_clk(unsigned long dummy) 115 { 116 return 66666666; 117 } 118 119 int misc_init_f(void) 120 { 121 /* configure QRIO pis for i2c deblocking */ 122 i2c_deblock_gpio_cfg(); 123 124 return 0; 125 } 126 127 #define NUM_SRDS_BANKS 2 128 #define PHY_RST 15 129 130 int misc_init_r(void) 131 { 132 serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; 133 u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100, 134 SRDS_PLLCR0_RFCK_SEL_125}; 135 unsigned int i; 136 137 /* check SERDES reference clocks */ 138 for (i = 0; i < NUM_SRDS_BANKS; i++) { 139 u32 actual = in_be32(®s->bank[i].pllcr0); 140 actual &= SRDS_PLLCR0_RFCK_SEL_MASK; 141 if (actual != expected[i]) { 142 printf("Warning: SERDES bank %u expects reference \ 143 clock %sMHz, but actual is %sMHz\n", i + 1, 144 serdes_clock_to_string(expected[i]), 145 serdes_clock_to_string(actual)); 146 } 147 } 148 149 /* take the mgmt eth phy out of reset */ 150 qrio_prst(PHY_RST, false, false); 151 152 return 0; 153 } 154 155 #if defined(CONFIG_HUSH_INIT_VAR) 156 int hush_init_var(void) 157 { 158 ivm_read_eeprom(); 159 return 0; 160 } 161 #endif 162 163 #if defined(CONFIG_LAST_STAGE_INIT) 164 int last_stage_init(void) 165 { 166 set_km_env(); 167 return 0; 168 } 169 #endif 170 171 #ifdef CONFIG_SYS_DPAA_FMAN 172 void fdt_fixup_fman_mac_addresses(void *blob) 173 { 174 int node, i, ret; 175 char *tmp, *end; 176 unsigned char mac_addr[6]; 177 178 /* get the mac addr from env */ 179 tmp = getenv("ethaddr"); 180 if (!tmp) { 181 printf("ethaddr env variable not defined\n"); 182 return; 183 } 184 for (i = 0; i < 6; i++) { 185 mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0; 186 if (tmp) 187 tmp = (*end) ? end+1 : end; 188 } 189 190 /* find the correct fdt ethernet path and correct it */ 191 node = fdt_path_offset(blob, "/soc/fman/ethernet@e8000"); 192 if (node < 0) { 193 printf("no /soc/fman/ethernet path offset\n"); 194 return; 195 } 196 ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6); 197 if (ret) { 198 printf("error setting local-mac-address property\n"); 199 return; 200 } 201 } 202 #endif 203 204 void ft_board_setup(void *blob, bd_t *bd) 205 { 206 phys_addr_t base; 207 phys_size_t size; 208 209 ft_cpu_setup(blob, bd); 210 211 base = getenv_bootm_low(); 212 size = getenv_bootm_size(); 213 214 fdt_fixup_memory(blob, (u64)base, (u64)size); 215 216 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 217 fdt_fixup_dr_usb(blob, bd); 218 #endif 219 220 #ifdef CONFIG_PCI 221 pci_of_setup(blob, bd); 222 #endif 223 224 fdt_fixup_liodn(blob); 225 #ifdef CONFIG_SYS_DPAA_FMAN 226 fdt_fixup_fman_ethernet(blob); 227 fdt_fixup_fman_mac_addresses(blob); 228 #endif 229 } 230