1#
2# (C) Copyright 2010
3# Heiko Schocher, DENX Software Engineering, hs@denx.de.
4#
5# See file CREDITS for list of people who contributed to this
6# project.
7#
8# This program is free software; you can redistribute it and/or
9# modify it under the terms of the GNU General Public License as
10# published by the Free Software Foundation; either version 2 of
11# the License, or (at your option) any later version.
12#
13# This program is distributed in the hope that it will be useful,
14# but WITHOUT ANY WARRANTY; without even the implied warranty of
15# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16# GNU General Public License for more details.
17#
18# You should have received a copy of the GNU General Public License
19# along with this program; if not, write to the Free Software
20# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
21# MA 02110-1301 USA
22#
23# Refer doc/README.kwbimage for more details about how-to configure
24# and create kirkwood boot image
25#
26
27# Boot Media configurations
28BOOT_FROM	spi	# Boot from SPI flash
29
30DATA 0xFFD10000 0x01112222	# MPP Control 0 Register
31# bit 3-0:   MPPSel0	2, NF_IO[2]
32# bit 7-4:   MPPSel1	2, NF_IO[3]
33# bit 12-8:  MPPSel2	2, NF_IO[4]
34# bit 15-12: MPPSel3	2, NF_IO[5]
35# bit 19-16: MPPSel4	1, NF_IO[6]
36# bit 23-20: MPPSel5	1, NF_IO[7]
37# bit 27-24: MPPSel6	1, SYSRST_O
38# bit 31-28: MPPSel7	0, GPO[7]
39
40DATA 0xFFD10004 0x03303300
41
42DATA 0xFFD10008 0x00001100	# MPP Control 2 Register
43# bit 3-0:   MPPSel16	0, GPIO[16]
44# bit 7-4:   MPPSel17	0, GPIO[17]
45# bit 12-8:  MPPSel18	1, NF_IO[0]
46# bit 15-12: MPPSel19	1, NF_IO[1]
47# bit 19-16: MPPSel20	0, GPIO[20]
48# bit 23-20: MPPSel21	0, GPIO[21]
49# bit 27-24: MPPSel22	0, GPIO[22]
50# bit 31-28: MPPSel23	0, GPIO[23]
51
52DATA 0xFFD100E0 0x1B1B1B1B	# IO Configuration 0 Register
53DATA 0xFFD20134 0x66666666	# L2 RAM Timing 0 Register
54DATA 0xFFD20138 0x66666666	# L2 RAM Timing 1 Register
55
56# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
57# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
58
59#Dram initalization
60DATA 0xFFD01400 0x43000400	# SDRAM Configuration Register
61# bit13-0:  0x400 (DDR2 clks refresh rate)
62# bit23-14: zero
63# bit24: 1= enable exit self refresh mode on DDR access
64# bit25: 1 required
65# bit29-26: zero
66# bit31-30: 01
67
68DATA 0xFFD01404 0x39543000	# DDR Controller Control Low
69# bit 3-0:  0 reserved
70# bit 4:    0=addr/cmd in smame cycle
71# bit 5:    0=clk is driven during self refresh, we don't care for APX
72# bit 6:    0=use recommended falling edge of clk for addr/cmd
73# bit14:    0=input buffer always powered up
74# bit18:    1=cpu lock transaction enabled
75# bit23-20: 3=recommended value for CL=3 and STARTBURST_DEL disabled bit31=0
76# bit27-24: 6= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
77# bit30-28: 3 required
78# bit31:    0=no additional STARTBURST delay
79
80DATA 0xFFD01408 0x34136552	# DDR Timing (Low) (active cycles value +1)
81# bit3-0:   TRAS lsbs
82# bit7-4:   TRCD
83# bit11- 8: TRP
84# bit15-12: TWR
85# bit19-16: TWTR
86# bit20:    TRAS msb
87# bit23-21: 0x0
88# bit27-24: TRRD
89# bit31-28: TRTP
90
91DATA 0xFFD0140C 0x00000033	#  DDR Timing (High)
92# bit6-0:   TRFC
93# bit8-7:   TR2R
94# bit10-9:  TR2W
95# bit12-11: TW2W
96# bit31-13: zero required
97
98DATA 0xFFD01410 0x0000000D	#  DDR Address Control
99# bit1-0:   01, Cs0width=x16
100# bit3-2:   11, Cs0size=1Gb
101# bit5-4:   00, Cs2width=nonexistent
102# bit7-6:   00, Cs1size =nonexistent
103# bit9-8:   00, Cs2width=nonexistent
104# bit11-10: 00, Cs2size =nonexistent
105# bit13-12: 00, Cs3width=nonexistent
106# bit15-14: 00, Cs3size =nonexistent
107# bit16:    0,  Cs0AddrSel
108# bit17:    0,  Cs1AddrSel
109# bit18:    0,  Cs2AddrSel
110# bit19:    0,  Cs3AddrSel
111# bit31-20: 0 required
112
113DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
114# bit0:    0,  OpenPage enabled
115# bit31-1: 0 required
116
117DATA 0xFFD01418 0x00000000	#  DDR Operation
118# bit3-0:   0x0, DDR cmd
119# bit31-4:  0 required
120
121DATA 0xFFD0141C 0x00000652	#  DDR Mode
122DATA 0xFFD01420 0x00000044	#  DDR Extended Mode
123# bit0:    0,  DDR DLL enabled
124# bit1:    0,  DDR drive strenght normal
125# bit2:    1,  DDR ODT control lsd disabled
126# bit5-3:  000, required
127# bit6:    1,  DDR ODT control msb, enabled
128# bit9-7:  000, required
129# bit10:   0,  differential DQS enabled
130# bit11:   0, required
131# bit12:   0, DDR output buffer enabled
132# bit31-13: 0 required
133
134DATA 0xFFD01424 0x0000F07F	#  DDR Controller Control High
135# bit2-0:  111, required
136# bit3  :  1  , MBUS Burst Chop disabled
137# bit6-4:  111, required
138# bit7  :  0
139# bit8  :  0  , no sample stage
140# bit9  :  0  , no half clock cycle addition to dataout
141# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
142# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
143# bit15-12: 1111 required
144# bit31-16: 0    required
145DATA 0xFFD01428 0x00074510
146DATA 0xFFD0147c 0x00007451
147
148DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
149DATA 0xFFD01504 0x07FFFFF1	# CS[0]n Size
150# bit0:    1,  Window enabled
151# bit1:    0,  Write Protect disabled
152# bit3-2:  00, CS0 hit selected
153# bit23-4: ones, required
154# bit31-24: 0x07, Size (i.e. 128MB)
155
156DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
157DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
158DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
159
160DATA 0xFFD01494 0x00010001	#  DDR ODT Control (Low)
161# bit3-0:  0, ODT0Rd, MODT[0] asserted during read from DRAM CS0
162# bit19-16:0, ODT0Wr, MODT[0] asserted during write to DRAM CS0
163
164DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
165# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
166# bit3-2:  00, ODT1 controlled by register
167# bit31-4: zero, required
168
169DATA 0xFFD0149C 0x0000FC11	# CPU ODT Control
170# bit3-0:  F, ODT0Rd, Internal ODT asserted during read from DRAM bank0
171# bit7-4:  0, ODT0Wr, Internal ODT asserted during write to DRAM bank0
172# bit9-8:  1, ODTEn, never active
173# bit11-10:2, DQ_ODTSel. ODT select turned on, 75 ohm
174
175DATA 0xFFD01480 0x00000001	# DDR Initialization Control
176# bit0=1, enable DDR init upon this register write
177
178# End of Header extension
179DATA 0x0 0x0
180