1 /* 2 * Copyright (C) 2006 Freescale Semiconductor, Inc. 3 * Dave Liu <daveliu@freescale.com> 4 * 5 * Copyright (C) 2007 Logic Product Development, Inc. 6 * Peter Barada <peterb@logicpd.com> 7 * 8 * Copyright (C) 2007 MontaVista Software, Inc. 9 * Anton Vorontsov <avorontsov@ru.mvista.com> 10 * 11 * (C) Copyright 2008 - 2010 12 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 13 * 14 * SPDX-License-Identifier: GPL-2.0+ 15 */ 16 17 #include <common.h> 18 #include <ioports.h> 19 #include <mpc83xx.h> 20 #include <i2c.h> 21 #include <miiphy.h> 22 #include <asm/io.h> 23 #include <asm/mmu.h> 24 #include <asm/processor.h> 25 #include <pci.h> 26 #include <libfdt.h> 27 #include <post.h> 28 29 #include "../common/common.h" 30 31 static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; 32 33 const qe_iop_conf_t qe_iop_conf_tab[] = { 34 /* port pin dir open_drain assign */ 35 #if defined(CONFIG_MPC8360) 36 /* MDIO */ 37 {0, 1, 3, 0, 2}, /* MDIO */ 38 {0, 2, 1, 0, 1}, /* MDC */ 39 40 /* UCC4 - UEC */ 41 {1, 14, 1, 0, 1}, /* TxD0 */ 42 {1, 15, 1, 0, 1}, /* TxD1 */ 43 {1, 20, 2, 0, 1}, /* RxD0 */ 44 {1, 21, 2, 0, 1}, /* RxD1 */ 45 {1, 18, 1, 0, 1}, /* TX_EN */ 46 {1, 26, 2, 0, 1}, /* RX_DV */ 47 {1, 27, 2, 0, 1}, /* RX_ER */ 48 {1, 24, 2, 0, 1}, /* COL */ 49 {1, 25, 2, 0, 1}, /* CRS */ 50 {2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */ 51 {2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */ 52 53 /* DUART - UART2 */ 54 {5, 0, 1, 0, 2}, /* UART2_SOUT */ 55 {5, 2, 1, 0, 1}, /* UART2_RTS */ 56 {5, 3, 2, 0, 2}, /* UART2_SIN */ 57 {5, 1, 2, 0, 3}, /* UART2_CTS */ 58 #elif !defined(CONFIG_MPC8309) 59 /* Local Bus */ 60 {0, 16, 1, 0, 3}, /* LA00 */ 61 {0, 17, 1, 0, 3}, /* LA01 */ 62 {0, 18, 1, 0, 3}, /* LA02 */ 63 {0, 19, 1, 0, 3}, /* LA03 */ 64 {0, 20, 1, 0, 3}, /* LA04 */ 65 {0, 21, 1, 0, 3}, /* LA05 */ 66 {0, 22, 1, 0, 3}, /* LA06 */ 67 {0, 23, 1, 0, 3}, /* LA07 */ 68 {0, 24, 1, 0, 3}, /* LA08 */ 69 {0, 25, 1, 0, 3}, /* LA09 */ 70 {0, 26, 1, 0, 3}, /* LA10 */ 71 {0, 27, 1, 0, 3}, /* LA11 */ 72 {0, 28, 1, 0, 3}, /* LA12 */ 73 {0, 29, 1, 0, 3}, /* LA13 */ 74 {0, 30, 1, 0, 3}, /* LA14 */ 75 {0, 31, 1, 0, 3}, /* LA15 */ 76 77 /* MDIO */ 78 {3, 4, 3, 0, 2}, /* MDIO */ 79 {3, 5, 1, 0, 2}, /* MDC */ 80 81 /* UCC4 - UEC */ 82 {1, 18, 1, 0, 1}, /* TxD0 */ 83 {1, 19, 1, 0, 1}, /* TxD1 */ 84 {1, 22, 2, 0, 1}, /* RxD0 */ 85 {1, 23, 2, 0, 1}, /* RxD1 */ 86 {1, 26, 2, 0, 1}, /* RxER */ 87 {1, 28, 2, 0, 1}, /* Rx_DV */ 88 {1, 30, 1, 0, 1}, /* TxEN */ 89 {1, 31, 2, 0, 1}, /* CRS */ 90 {3, 10, 2, 0, 3}, /* TxCLK->CLK17 */ 91 #endif 92 93 /* END of table */ 94 {0, 0, 0, 0, QE_IOP_TAB_END}, 95 }; 96 97 #if defined(CONFIG_SUVD3) 98 const uint upma_table[] = { 99 0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */ 100 0x0ffcdc00, 0xffffcc00, 0xffffcc01, 0xfffffc01, /* Words 4 to 7 */ 101 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 8 to 11 */ 102 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 12 to 15 */ 103 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 16 to 19 */ 104 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 20 to 23 */ 105 0x9cfffc00, 0x00fffc80, 0x00fffc80, 0x00fffc00, /* Words 24 to 27 */ 106 0xffffec04, 0xffffec01, 0xfffffc01, 0xfffffc01, /* Words 28 to 31 */ 107 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 32 to 35 */ 108 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 36 to 39 */ 109 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 40 to 43 */ 110 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 44 to 47 */ 111 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 48 to 51 */ 112 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 52 to 55 */ 113 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 56 to 59 */ 114 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01 /* Words 60 to 63 */ 115 }; 116 #endif 117 118 static int piggy_present(void) 119 { 120 struct km_bec_fpga __iomem *base = 121 (struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE; 122 123 return in_8(&base->bprth) & PIGGY_PRESENT; 124 } 125 126 #if defined(CONFIG_KMVECT1) 127 int ethernet_present(void) 128 { 129 /* ethernet port connected to simple switch without piggy */ 130 return 1; 131 } 132 #else 133 int ethernet_present(void) 134 { 135 return piggy_present(); 136 } 137 #endif 138 139 140 int board_early_init_r(void) 141 { 142 struct km_bec_fpga *base = 143 (struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE; 144 #if defined(CONFIG_SUVD3) 145 immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; 146 fsl_lbc_t *lbc = &immap->im_lbc; 147 u32 *mxmr = &lbc->mamr; 148 #endif 149 150 #if defined(CONFIG_MPC8360) 151 unsigned short svid; 152 /* 153 * Because of errata in the UCCs, we have to write to the reserved 154 * registers to slow the clocks down. 155 */ 156 svid = SVR_REV(mfspr(SVR)); 157 switch (svid) { 158 case 0x0020: 159 /* 160 * MPC8360ECE.pdf QE_ENET10 table 4: 161 * IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2) 162 * IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1) 163 */ 164 setbits_be32((void *)(CONFIG_SYS_IMMR + 0x14a8), 0x0c003000); 165 break; 166 case 0x0021: 167 /* 168 * MPC8360ECE.pdf QE_ENET10 table 4: 169 * IMMR + 0x14AC[24:27] = 1010 170 */ 171 clrsetbits_be32((void *)(CONFIG_SYS_IMMR + 0x14ac), 172 0x00000050, 0x000000a0); 173 break; 174 } 175 #endif 176 177 /* enable the PHY on the PIGGY */ 178 setbits_8(&base->pgy_eth, 0x01); 179 /* enable the Unit LED (green) */ 180 setbits_8(&base->oprth, WRL_BOOT); 181 /* enable Application Buffer */ 182 setbits_8(&base->oprtl, OPRTL_XBUFENA); 183 184 #if defined(CONFIG_SUVD3) 185 /* configure UPMA for APP1 */ 186 upmconfig(UPMA, (uint *) upma_table, 187 sizeof(upma_table) / sizeof(uint)); 188 out_be32(mxmr, CONFIG_SYS_MAMR); 189 #endif 190 return 0; 191 } 192 193 int misc_init_r(void) 194 { 195 ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); 196 return 0; 197 } 198 199 #if defined(CONFIG_KMVECT1) 200 #include <mv88e6352.h> 201 /* Marvell MV88E6122 switch configuration */ 202 static struct mv88e_sw_reg extsw_conf[] = { 203 /* port 1, FRONT_MDI, autoneg */ 204 { PORT(1), PORT_PHY, NO_SPEED_FOR }, 205 { PORT(1), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, 206 { PHY(1), PHY_1000_CTRL, NO_ADV }, 207 { PHY(1), PHY_SPEC_CTRL, AUTO_MDIX_EN }, 208 { PHY(1), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST | 209 FULL_DUPLEX }, 210 /* port 2, unused */ 211 { PORT(2), PORT_CTRL, PORT_DIS }, 212 { PHY(2), PHY_CTRL, PHY_PWR_DOWN }, 213 { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, 214 /* port 3, BP_MII (CPU), PHY mode, 100BASE */ 215 { PORT(3), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, 216 /* port 4, ESTAR to slot 11, SerDes, 1000BASE-X */ 217 { PORT(4), PORT_STATUS, NO_PHY_DETECT }, 218 { PORT(4), PORT_PHY, SPEED_1000_FOR }, 219 { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, 220 /* port 5, ESTAR to slot 13, SerDes, 1000BASE-X */ 221 { PORT(5), PORT_STATUS, NO_PHY_DETECT }, 222 { PORT(5), PORT_PHY, SPEED_1000_FOR }, 223 { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, 224 /* 225 * Errata Fix: 1.9V Output from Internal 1.8V Regulator, 226 * acc . MV-S300889-00D.pdf , clause 4.5 227 */ 228 { PORT(5), 0x1A, 0xADB1 }, 229 /* port 6, unused, this port has no phy */ 230 { PORT(6), PORT_CTRL, PORT_DIS }, 231 /* 232 * Errata Fix: 1.9V Output from Internal 1.8V Regulator, 233 * acc . MV-S300889-00D.pdf , clause 4.5 234 */ 235 { PORT(5), 0x1A, 0xADB1 }, 236 }; 237 #endif 238 239 int last_stage_init(void) 240 { 241 #if defined(CONFIG_KMVECT1) 242 struct km_bec_fpga __iomem *base = 243 (struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE; 244 u8 tmp_reg; 245 246 /* Release mv88e6122 from reset */ 247 tmp_reg = in_8(&base->res1[0]) | 0x10; /* DIRECT3 register */ 248 out_8(&base->res1[0], tmp_reg); /* GP28 as output */ 249 tmp_reg = in_8(&base->gprt3) | 0x10; /* GP28 to high */ 250 out_8(&base->gprt3, tmp_reg); 251 252 /* configure MV88E6122 switch */ 253 char *name = "UEC2"; 254 255 if (miiphy_set_current_dev(name)) 256 return 0; 257 258 mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf, 259 ARRAY_SIZE(extsw_conf)); 260 261 mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR); 262 263 if (piggy_present()) { 264 setenv("ethact", "UEC2"); 265 setenv("netdev", "eth1"); 266 puts("using PIGGY for network boot\n"); 267 } else { 268 setenv("netdev", "eth0"); 269 puts("using frontport for network boot\n"); 270 } 271 #endif 272 273 #if defined(CONFIG_KMCOGE5NE) 274 struct bfticu_iomap *base = 275 (struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE; 276 u8 dip_switch = in_8((u8 *)&(base->mswitch)) & BFTICU_DIPSWITCH_MASK; 277 278 if (dip_switch != 0) { 279 /* start bootloader */ 280 puts("DIP: Enabled\n"); 281 setenv("actual_bank", "0"); 282 } 283 #endif 284 set_km_env(); 285 return 0; 286 } 287 288 static int fixed_sdram(void) 289 { 290 immap_t *im = (immap_t *)CONFIG_SYS_IMMR; 291 u32 msize = 0; 292 u32 ddr_size; 293 u32 ddr_size_log2; 294 295 out_be32(&im->sysconf.ddrlaw[0].ar, (LAWAR_EN | 0x1e)); 296 out_be32(&im->ddr.csbnds[0].csbnds, (CONFIG_SYS_DDR_CS0_BNDS) | 0x7f); 297 out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG); 298 out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); 299 out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); 300 out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); 301 out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); 302 out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG); 303 out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2); 304 out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE); 305 out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2); 306 out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL); 307 out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL); 308 udelay(200); 309 setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN); 310 311 msize = CONFIG_SYS_DDR_SIZE << 20; 312 disable_addr_trans(); 313 msize = get_ram_size(CONFIG_SYS_DDR_BASE, msize); 314 enable_addr_trans(); 315 msize /= (1024 * 1024); 316 if (CONFIG_SYS_DDR_SIZE != msize) { 317 for (ddr_size = msize << 20, ddr_size_log2 = 0; 318 (ddr_size > 1); 319 ddr_size = ddr_size >> 1, ddr_size_log2++) 320 if (ddr_size & 1) 321 return -1; 322 out_be32(&im->sysconf.ddrlaw[0].ar, 323 (LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE))); 324 out_be32(&im->ddr.csbnds[0].csbnds, 325 (((msize / 16) - 1) & 0xff)); 326 } 327 328 return msize; 329 } 330 331 phys_size_t initdram(int board_type) 332 { 333 immap_t *im = (immap_t *)CONFIG_SYS_IMMR; 334 u32 msize = 0; 335 336 if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im) 337 return -1; 338 339 out_be32(&im->sysconf.ddrlaw[0].bar, 340 CONFIG_SYS_DDR_BASE & LAWBAR_BAR); 341 msize = fixed_sdram(); 342 343 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) 344 /* 345 * Initialize DDR ECC byte 346 */ 347 ddr_enable_ecc(msize * 1024 * 1024); 348 #endif 349 350 /* return total bus SDRAM size(bytes) -- DDR */ 351 return msize * 1024 * 1024; 352 } 353 354 int checkboard(void) 355 { 356 puts("Board: Keymile " CONFIG_KM_BOARD_NAME); 357 358 if (piggy_present()) 359 puts(" with PIGGY."); 360 puts("\n"); 361 return 0; 362 } 363 364 #if defined(CONFIG_OF_BOARD_SETUP) 365 int ft_board_setup(void *blob, bd_t *bd) 366 { 367 ft_cpu_setup(blob, bd); 368 369 return 0; 370 } 371 #endif 372 373 #if defined(CONFIG_HUSH_INIT_VAR) 374 int hush_init_var(void) 375 { 376 ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); 377 return 0; 378 } 379 #endif 380 381 #if defined(CONFIG_POST) 382 int post_hotkeys_pressed(void) 383 { 384 int testpin = 0; 385 struct km_bec_fpga *base = 386 (struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE; 387 int testpin_reg = in_8(&base->CONFIG_TESTPIN_REG); 388 testpin = (testpin_reg & CONFIG_TESTPIN_MASK) != 0; 389 debug("post_hotkeys_pressed: %d\n", !testpin); 390 return testpin; 391 } 392 393 ulong post_word_load(void) 394 { 395 void* addr = (ulong *) (CPM_POST_WORD_ADDR); 396 debug("post_word_load 0x%08lX: 0x%08X\n", (ulong)addr, in_le32(addr)); 397 return in_le32(addr); 398 399 } 400 void post_word_store(ulong value) 401 { 402 void* addr = (ulong *) (CPM_POST_WORD_ADDR); 403 debug("post_word_store 0x%08lX: 0x%08lX\n", (ulong)addr, value); 404 out_le32(addr, value); 405 } 406 407 int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset) 408 { 409 *vstart = CONFIG_SYS_MEMTEST_START; 410 *size = CONFIG_SYS_MEMTEST_END - CONFIG_SYS_MEMTEST_START; 411 debug("arch_memory_test_prepare 0x%08X 0x%08X\n", *vstart, *size); 412 413 return 0; 414 } 415 #endif 416