1 /* 2 * (C) Copyright 2010 3 * ISEE 2007 SL, <www.iseebcn.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 #include <common.h> 8 #include <status_led.h> 9 #include <dm.h> 10 #include <ns16550.h> 11 #include <twl4030.h> 12 #include <netdev.h> 13 #include <spl.h> 14 #include <asm/gpio.h> 15 #include <asm/io.h> 16 #include <asm/arch/mem.h> 17 #include <asm/arch/mmc_host_def.h> 18 #include <asm/arch/mux.h> 19 #include <asm/arch/sys_proto.h> 20 #include <linux/mtd/mtd.h> 21 #include <linux/mtd/rawnand.h> 22 #include <linux/mtd/onenand.h> 23 #include <jffs2/load_kernel.h> 24 #include <mtd_node.h> 25 #include <fdt_support.h> 26 #include "igep00x0.h" 27 28 static const struct ns16550_platdata igep_serial = { 29 .base = OMAP34XX_UART3, 30 .reg_shift = 2, 31 .clock = V_NS16550_CLK, 32 .fcr = UART_FCR_DEFVAL, 33 }; 34 35 U_BOOT_DEVICE(igep_uart) = { 36 "ns16550_serial", 37 &igep_serial 38 }; 39 40 /* 41 * Routine: get_board_revision 42 * Description: GPIO_28 and GPIO_129 are used to read board and revision from 43 * IGEP00x0 boards. First of all, it is necessary to reset USB transceiver from 44 * IGEP0030 in order to read GPIO_IGEP00X0_BOARD_DETECTION correctly, because 45 * this functionality is shared by USB HOST. 46 * Once USB reset is applied, U-boot configures these pins as input pullup to 47 * detect board and revision: 48 * IGEP0020-RF = 0b00 49 * IGEP0020-RC = 0b01 50 * IGEP0030-RG = 0b10 51 * IGEP0030-RE = 0b11 52 */ 53 static int get_board_revision(void) 54 { 55 int revision; 56 57 gpio_request(IGEP0030_USB_TRANSCEIVER_RESET, 58 "igep0030_usb_transceiver_reset"); 59 gpio_direction_output(IGEP0030_USB_TRANSCEIVER_RESET, 0); 60 61 gpio_request(GPIO_IGEP00X0_BOARD_DETECTION, "igep00x0_board_detection"); 62 gpio_direction_input(GPIO_IGEP00X0_BOARD_DETECTION); 63 revision = 2 * gpio_get_value(GPIO_IGEP00X0_BOARD_DETECTION); 64 gpio_free(GPIO_IGEP00X0_BOARD_DETECTION); 65 66 gpio_request(GPIO_IGEP00X0_REVISION_DETECTION, 67 "igep00x0_revision_detection"); 68 gpio_direction_input(GPIO_IGEP00X0_REVISION_DETECTION); 69 revision = revision + gpio_get_value(GPIO_IGEP00X0_REVISION_DETECTION); 70 gpio_free(GPIO_IGEP00X0_REVISION_DETECTION); 71 72 gpio_free(IGEP0030_USB_TRANSCEIVER_RESET); 73 74 return revision; 75 } 76 77 int onenand_board_init(struct mtd_info *mtd) 78 { 79 if (gpmc_cs0_flash == MTD_DEV_TYPE_ONENAND) { 80 struct onenand_chip *this = mtd->priv; 81 this->base = (void *)CONFIG_SYS_ONENAND_BASE; 82 return 0; 83 } 84 return 1; 85 } 86 87 #if defined(CONFIG_CMD_NET) 88 static void reset_net_chip(int gpio) 89 { 90 if (!gpio_request(gpio, "eth nrst")) { 91 gpio_direction_output(gpio, 1); 92 udelay(1); 93 gpio_set_value(gpio, 0); 94 udelay(40); 95 gpio_set_value(gpio, 1); 96 mdelay(10); 97 } 98 } 99 100 /* 101 * Routine: setup_net_chip 102 * Description: Setting up the configuration GPMC registers specific to the 103 * Ethernet hardware. 104 */ 105 static void setup_net_chip(void) 106 { 107 struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE; 108 static const u32 gpmc_lan_config[] = { 109 NET_LAN9221_GPMC_CONFIG1, 110 NET_LAN9221_GPMC_CONFIG2, 111 NET_LAN9221_GPMC_CONFIG3, 112 NET_LAN9221_GPMC_CONFIG4, 113 NET_LAN9221_GPMC_CONFIG5, 114 NET_LAN9221_GPMC_CONFIG6, 115 }; 116 117 enable_gpmc_cs_config(gpmc_lan_config, &gpmc_cfg->cs[5], 118 CONFIG_SMC911X_BASE, GPMC_SIZE_16M); 119 120 /* Enable off mode for NWE in PADCONF_GPMC_NWE register */ 121 writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe); 122 /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */ 123 writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe); 124 /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */ 125 writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00, 126 &ctrl_base->gpmc_nadv_ale); 127 128 reset_net_chip(64); 129 } 130 131 int board_eth_init(bd_t *bis) 132 { 133 #ifdef CONFIG_SMC911X 134 return smc911x_initialize(0, CONFIG_SMC911X_BASE); 135 #else 136 return 0; 137 #endif 138 } 139 #else 140 static inline void setup_net_chip(void) {} 141 #endif 142 143 #ifdef CONFIG_OF_BOARD_SETUP 144 static int ft_enable_by_compatible(void *blob, char *compat, int enable) 145 { 146 int off = fdt_node_offset_by_compatible(blob, -1, compat); 147 if (off < 0) 148 return off; 149 150 if (enable) 151 fdt_status_okay(blob, off); 152 else 153 fdt_status_disabled(blob, off); 154 155 return 0; 156 } 157 158 int ft_board_setup(void *blob, bd_t *bd) 159 { 160 #ifdef CONFIG_FDT_FIXUP_PARTITIONS 161 static struct node_info nodes[] = { 162 { "ti,omap2-nand", MTD_DEV_TYPE_NAND, }, 163 { "ti,omap2-onenand", MTD_DEV_TYPE_ONENAND, }, 164 }; 165 166 fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes)); 167 #endif 168 ft_enable_by_compatible(blob, "ti,omap2-nand", 169 gpmc_cs0_flash == MTD_DEV_TYPE_NAND); 170 ft_enable_by_compatible(blob, "ti,omap2-onenand", 171 gpmc_cs0_flash == MTD_DEV_TYPE_ONENAND); 172 173 return 0; 174 } 175 #endif 176 177 void set_led(void) 178 { 179 switch (get_board_revision()) { 180 case 0: 181 case 1: 182 gpio_request(IGEP0020_GPIO_LED, "igep0020_gpio_led"); 183 gpio_direction_output(IGEP0020_GPIO_LED, 1); 184 break; 185 case 2: 186 case 3: 187 gpio_request(IGEP0030_GPIO_LED, "igep0030_gpio_led"); 188 gpio_direction_output(IGEP0030_GPIO_LED, 0); 189 break; 190 default: 191 /* Should not happen... */ 192 break; 193 } 194 } 195 196 void set_boardname(void) 197 { 198 char rev[5] = { 'F','C','G','E', }; 199 int i = get_board_revision(); 200 201 rev[i+1] = 0; 202 env_set("board_rev", rev + i); 203 env_set("board_name", i < 2 ? "igep0020" : "igep0030"); 204 } 205 206 /* 207 * Routine: misc_init_r 208 * Description: Configure board specific parts 209 */ 210 int misc_init_r(void) 211 { 212 t2_t *t2_base = (t2_t *)T2_BASE; 213 u32 pbias_lite; 214 215 twl4030_power_init(); 216 217 /* set VSIM to 1.8V */ 218 twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VSIM_DEDICATED, 219 TWL4030_PM_RECEIVER_VSIM_VSEL_18, 220 TWL4030_PM_RECEIVER_VSIM_DEV_GRP, 221 TWL4030_PM_RECEIVER_DEV_GRP_P1); 222 223 /* set up dual-voltage GPIOs to 1.8V */ 224 pbias_lite = readl(&t2_base->pbias_lite); 225 pbias_lite &= ~PBIASLITEVMODE1; 226 pbias_lite |= PBIASLITEPWRDNZ1; 227 writel(pbias_lite, &t2_base->pbias_lite); 228 if (get_cpu_family() == CPU_OMAP36XX) 229 writel(readl(OMAP34XX_CTRL_WKUP_CTRL) | 230 OMAP34XX_CTRL_WKUP_CTRL_GPIO_IO_PWRDNZ, 231 OMAP34XX_CTRL_WKUP_CTRL); 232 233 setup_net_chip(); 234 235 omap_die_id_display(); 236 237 set_led(); 238 239 set_boardname(); 240 241 return 0; 242 } 243 244 void board_mtdparts_default(const char **mtdids, const char **mtdparts) 245 { 246 struct mtd_info *mtd = get_mtd_device(NULL, 0); 247 if (mtd) { 248 static char ids[24]; 249 static char parts[48]; 250 const char *linux_name = "omap2-nand"; 251 if (strncmp(mtd->name, "onenand0", 8) == 0) 252 linux_name = "omap2-onenand"; 253 snprintf(ids, sizeof(ids), "%s=%s", mtd->name, linux_name); 254 snprintf(parts, sizeof(parts), "mtdparts=%s:%dk(SPL),-(UBI)", 255 linux_name, 4 * mtd->erasesize >> 10); 256 *mtdids = ids; 257 *mtdparts = parts; 258 } 259 } 260