1 /* 2 * (C) Copyright 2015 Linaro 3 * Peter Griffin <peter.griffin@linaro.org> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 #include <common.h> 8 #include <dm.h> 9 #include <dm/platform_data/serial_pl01x.h> 10 #include <errno.h> 11 #include <malloc.h> 12 #include <netdev.h> 13 #include <asm/io.h> 14 #include <usb.h> 15 #include <power/hi6553_pmic.h> 16 #include <asm-generic/gpio.h> 17 #include <asm/arch/dwmmc.h> 18 #include <asm/arch/gpio.h> 19 #include <asm/arch/periph.h> 20 #include <asm/arch/pinmux.h> 21 #include <asm/arch/hi6220.h> 22 #include <asm/armv8/mmu.h> 23 24 /*TODO drop this table in favour of device tree */ 25 static const struct hikey_gpio_platdata hi6220_gpio[] = { 26 { 0, HI6220_GPIO_BASE(0)}, 27 { 1, HI6220_GPIO_BASE(1)}, 28 { 2, HI6220_GPIO_BASE(2)}, 29 { 3, HI6220_GPIO_BASE(3)}, 30 { 4, HI6220_GPIO_BASE(4)}, 31 { 5, HI6220_GPIO_BASE(5)}, 32 { 6, HI6220_GPIO_BASE(6)}, 33 { 7, HI6220_GPIO_BASE(7)}, 34 { 8, HI6220_GPIO_BASE(8)}, 35 { 9, HI6220_GPIO_BASE(9)}, 36 { 10, HI6220_GPIO_BASE(10)}, 37 { 11, HI6220_GPIO_BASE(11)}, 38 { 12, HI6220_GPIO_BASE(12)}, 39 { 13, HI6220_GPIO_BASE(13)}, 40 { 14, HI6220_GPIO_BASE(14)}, 41 { 15, HI6220_GPIO_BASE(15)}, 42 { 16, HI6220_GPIO_BASE(16)}, 43 { 17, HI6220_GPIO_BASE(17)}, 44 { 18, HI6220_GPIO_BASE(18)}, 45 { 19, HI6220_GPIO_BASE(19)}, 46 47 }; 48 49 U_BOOT_DEVICES(hi6220_gpios) = { 50 { "gpio_hi6220", &hi6220_gpio[0] }, 51 { "gpio_hi6220", &hi6220_gpio[1] }, 52 { "gpio_hi6220", &hi6220_gpio[2] }, 53 { "gpio_hi6220", &hi6220_gpio[3] }, 54 { "gpio_hi6220", &hi6220_gpio[4] }, 55 { "gpio_hi6220", &hi6220_gpio[5] }, 56 { "gpio_hi6220", &hi6220_gpio[6] }, 57 { "gpio_hi6220", &hi6220_gpio[7] }, 58 { "gpio_hi6220", &hi6220_gpio[8] }, 59 { "gpio_hi6220", &hi6220_gpio[9] }, 60 { "gpio_hi6220", &hi6220_gpio[10] }, 61 { "gpio_hi6220", &hi6220_gpio[11] }, 62 { "gpio_hi6220", &hi6220_gpio[12] }, 63 { "gpio_hi6220", &hi6220_gpio[13] }, 64 { "gpio_hi6220", &hi6220_gpio[14] }, 65 { "gpio_hi6220", &hi6220_gpio[15] }, 66 { "gpio_hi6220", &hi6220_gpio[16] }, 67 { "gpio_hi6220", &hi6220_gpio[17] }, 68 { "gpio_hi6220", &hi6220_gpio[18] }, 69 { "gpio_hi6220", &hi6220_gpio[19] }, 70 }; 71 72 DECLARE_GLOBAL_DATA_PTR; 73 74 #if !CONFIG_IS_ENABLED(OF_CONTROL) 75 76 static const struct pl01x_serial_platdata serial_platdata = { 77 #if CONFIG_CONS_INDEX == 1 78 .base = HI6220_UART0_BASE, 79 #elif CONFIG_CONS_INDEX == 4 80 .base = HI6220_UART3_BASE, 81 #else 82 #error "Unsupported console index value." 83 #endif 84 .type = TYPE_PL011, 85 .clock = 19200000 86 }; 87 88 U_BOOT_DEVICE(hikey_seriala) = { 89 .name = "serial_pl01x", 90 .platdata = &serial_platdata, 91 }; 92 #endif 93 94 static struct mm_region hikey_mem_map[] = { 95 { 96 .virt = 0x0UL, 97 .phys = 0x0UL, 98 .size = 0x80000000UL, 99 .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | 100 PTE_BLOCK_INNER_SHARE 101 }, { 102 .virt = 0x80000000UL, 103 .phys = 0x80000000UL, 104 .size = 0x80000000UL, 105 .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | 106 PTE_BLOCK_NON_SHARE | 107 PTE_BLOCK_PXN | PTE_BLOCK_UXN 108 }, { 109 /* List terminator */ 110 0, 111 } 112 }; 113 114 struct mm_region *mem_map = hikey_mem_map; 115 116 #ifdef CONFIG_BOARD_EARLY_INIT_F 117 int board_uart_init(void) 118 { 119 switch (CONFIG_CONS_INDEX) { 120 case 1: 121 hi6220_pinmux_config(PERIPH_ID_UART0); 122 break; 123 case 4: 124 hi6220_pinmux_config(PERIPH_ID_UART3); 125 break; 126 default: 127 debug("%s: Unsupported UART selected\n", __func__); 128 return -1; 129 } 130 131 return 0; 132 } 133 134 int board_early_init_f(void) 135 { 136 board_uart_init(); 137 return 0; 138 } 139 #endif 140 141 struct peri_sc_periph_regs *peri_sc = 142 (struct peri_sc_periph_regs *)HI6220_PERI_BASE; 143 144 struct alwayson_sc_regs *ao_sc = 145 (struct alwayson_sc_regs *)ALWAYSON_CTRL_BASE; 146 147 /* status offset from enable reg */ 148 #define STAT_EN_OFF 0x2 149 150 void hi6220_clk_enable(u32 bitfield, unsigned int *clk_base) 151 { 152 uint32_t data; 153 154 data = readl(clk_base); 155 data |= bitfield; 156 157 writel(bitfield, clk_base); 158 do { 159 data = readl(clk_base + STAT_EN_OFF); 160 } while ((data & bitfield) == 0); 161 } 162 163 /* status offset from disable reg */ 164 #define STAT_DIS_OFF 0x1 165 166 void hi6220_clk_disable(u32 bitfield, unsigned int *clk_base) 167 { 168 uint32_t data; 169 170 data = readl(clk_base); 171 data |= bitfield; 172 173 writel(data, clk_base); 174 do { 175 data = readl(clk_base + STAT_DIS_OFF); 176 } while (data & bitfield); 177 } 178 179 #define EYE_PATTERN 0x70533483 180 181 int board_usb_init(int index, enum usb_init_type init) 182 { 183 unsigned int data; 184 185 /* enable USB clock */ 186 hi6220_clk_enable(PERI_CLK0_USBOTG, &peri_sc->clk0_en); 187 188 /* take usb IPs out of reset */ 189 writel(PERI_RST0_USBOTG_BUS | PERI_RST0_POR_PICOPHY | 190 PERI_RST0_USBOTG | PERI_RST0_USBOTG_32K, 191 &peri_sc->rst0_dis); 192 do { 193 data = readl(&peri_sc->rst0_stat); 194 data &= PERI_RST0_USBOTG_BUS | PERI_RST0_POR_PICOPHY | 195 PERI_RST0_USBOTG | PERI_RST0_USBOTG_32K; 196 } while (data); 197 198 /*CTRL 5*/ 199 data = readl(&peri_sc->ctrl5); 200 data &= ~PERI_CTRL5_PICOPHY_BC_MODE; 201 data |= PERI_CTRL5_USBOTG_RES_SEL | PERI_CTRL5_PICOPHY_ACAENB; 202 data |= 0x300; 203 writel(data, &peri_sc->ctrl5); 204 205 /*CTRL 4*/ 206 207 /* configure USB PHY */ 208 data = readl(&peri_sc->ctrl4); 209 210 /* make PHY out of low power mode */ 211 data &= ~PERI_CTRL4_PICO_SIDDQ; 212 data &= ~PERI_CTRL4_PICO_OGDISABLE; 213 data |= PERI_CTRL4_PICO_VBUSVLDEXTSEL | PERI_CTRL4_PICO_VBUSVLDEXT; 214 writel(data, &peri_sc->ctrl4); 215 216 writel(EYE_PATTERN, &peri_sc->ctrl8); 217 218 mdelay(5); 219 return 0; 220 } 221 222 static int config_sd_carddetect(void) 223 { 224 int ret; 225 226 /* configure GPIO8 as nopull */ 227 writel(0, 0xf8001830); 228 229 gpio_request(8, "SD CD"); 230 231 gpio_direction_input(8); 232 ret = gpio_get_value(8); 233 234 if (!ret) { 235 printf("%s: SD card present\n", __func__); 236 return 1; 237 } 238 239 printf("%s: SD card not present\n", __func__); 240 return 0; 241 } 242 243 244 static void mmc1_init_pll(void) 245 { 246 uint32_t data; 247 248 /* select SYSPLL as the source of MMC1 */ 249 /* select SYSPLL as the source of MUX1 (SC_CLK_SEL0) */ 250 writel(1 << 11 | 1 << 27, &peri_sc->clk0_sel); 251 do { 252 data = readl(&peri_sc->clk0_sel); 253 } while (!(data & (1 << 11))); 254 255 /* select MUX1 as the source of MUX2 (SC_CLK_SEL0) */ 256 writel(1 << 30, &peri_sc->clk0_sel); 257 do { 258 data = readl(&peri_sc->clk0_sel); 259 } while (data & (1 << 14)); 260 261 hi6220_clk_enable(PERI_CLK0_MMC1, &peri_sc->clk0_en); 262 263 hi6220_clk_enable(PERI_CLK12_MMC1_SRC, &peri_sc->clk12_en); 264 265 do { 266 /* 1.2GHz / 50 = 24MHz */ 267 writel(0x31 | (1 << 7), &peri_sc->clkcfg8bit2); 268 data = readl(&peri_sc->clkcfg8bit2); 269 } while ((data & 0x31) != 0x31); 270 } 271 272 static void mmc1_reset_clk(void) 273 { 274 unsigned int data; 275 276 /* disable mmc1 bus clock */ 277 hi6220_clk_disable(PERI_CLK0_MMC1, &peri_sc->clk0_dis); 278 279 /* enable mmc1 bus clock */ 280 hi6220_clk_enable(PERI_CLK0_MMC1, &peri_sc->clk0_en); 281 282 /* reset mmc1 clock domain */ 283 writel(PERI_RST0_MMC1, &peri_sc->rst0_en); 284 285 /* bypass mmc1 clock phase */ 286 data = readl(&peri_sc->ctrl2); 287 data |= 3 << 2; 288 writel(data, &peri_sc->ctrl2); 289 290 /* disable low power */ 291 data = readl(&peri_sc->ctrl13); 292 data |= 1 << 4; 293 writel(data, &peri_sc->ctrl13); 294 do { 295 data = readl(&peri_sc->rst0_stat); 296 } while (!(data & PERI_RST0_MMC1)); 297 298 /* unreset mmc0 clock domain */ 299 writel(PERI_RST0_MMC1, &peri_sc->rst0_dis); 300 do { 301 data = readl(&peri_sc->rst0_stat); 302 } while (data & PERI_RST0_MMC1); 303 } 304 305 /* PMU SSI is the IP that maps the external PMU hi6553 registers as IO */ 306 static void hi6220_pmussi_init(void) 307 { 308 uint32_t data; 309 310 /* Take PMUSSI out of reset */ 311 writel(ALWAYSON_SC_PERIPH_RST4_DIS_PRESET_PMUSSI_N, 312 &ao_sc->rst4_dis); 313 do { 314 data = readl(&ao_sc->rst4_stat); 315 } while (data & ALWAYSON_SC_PERIPH_RST4_DIS_PRESET_PMUSSI_N); 316 317 /* set PMU SSI clock latency for read operation */ 318 data = readl(&ao_sc->mcu_subsys_ctrl3); 319 data &= ~ALWAYSON_SC_MCU_SUBSYS_CTRL3_RCLK_MASK; 320 data |= ALWAYSON_SC_MCU_SUBSYS_CTRL3_RCLK_3; 321 writel(data, &ao_sc->mcu_subsys_ctrl3); 322 323 /* enable PMUSSI clock */ 324 data = ALWAYSON_SC_PERIPH_CLK5_EN_PCLK_PMUSSI_CCPU | 325 ALWAYSON_SC_PERIPH_CLK5_EN_PCLK_PMUSSI_MCU; 326 327 hi6220_clk_enable(data, &ao_sc->clk5_en); 328 329 /* Output high to PMIC on PWR_HOLD_GPIO0_0 */ 330 gpio_request(0, "PWR_HOLD_GPIO0_0"); 331 gpio_direction_output(0, 1); 332 } 333 334 int misc_init_r(void) 335 { 336 return 0; 337 } 338 339 int board_init(void) 340 { 341 return 0; 342 } 343 344 #ifdef CONFIG_GENERIC_MMC 345 346 static int init_dwmmc(void) 347 { 348 int ret; 349 350 #ifdef CONFIG_DWMMC 351 352 /* mmc0 clocks are already configured by ATF */ 353 ret = hi6220_pinmux_config(PERIPH_ID_SDMMC0); 354 if (ret) 355 printf("%s: Error configuring pinmux for eMMC (%d)\n" 356 , __func__, ret); 357 358 ret |= hi6220_dwmci_add_port(0, HI6220_MMC0_BASE, 8); 359 if (ret) 360 printf("%s: Error adding eMMC port (%d)\n", __func__, ret); 361 362 363 /* take mmc1 (sd slot) out of reset, configure clocks and pinmuxing */ 364 mmc1_init_pll(); 365 mmc1_reset_clk(); 366 367 ret |= hi6220_pinmux_config(PERIPH_ID_SDMMC1); 368 if (ret) 369 printf("%s: Error configuring pinmux for eMMC (%d)\n" 370 , __func__, ret); 371 372 config_sd_carddetect(); 373 374 ret |= hi6220_dwmci_add_port(1, HI6220_MMC1_BASE, 4); 375 if (ret) 376 printf("%s: Error adding SD port (%d)\n", __func__, ret); 377 378 #endif 379 return ret; 380 } 381 382 /* setup board specific PMIC */ 383 int power_init_board(void) 384 { 385 /* init the hi6220 pmussi ip */ 386 hi6220_pmussi_init(); 387 388 power_hi6553_init((u8 *)HI6220_PMUSSI_BASE); 389 390 return 0; 391 } 392 393 int board_mmc_init(bd_t *bis) 394 { 395 int ret; 396 397 /* add the eMMC and sd ports */ 398 ret = init_dwmmc(); 399 400 if (ret) 401 debug("init_dwmmc failed\n"); 402 403 return ret; 404 } 405 #endif 406 407 int dram_init(void) 408 { 409 gd->ram_size = PHYS_SDRAM_1_SIZE; 410 return 0; 411 } 412 413 void dram_init_banksize(void) 414 { 415 /* 416 * Reserve regions below from DT memory node (which gets generated 417 * by U-Boot from the dram banks in arch_fixup_fdt() before booting 418 * the kernel. This will then match the kernel hikey dts memory node. 419 * 420 * 0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using 421 * 0x05f0,1000 - 0x05f0,1fff: Reboot reason 422 * 0x06df,f000 - 0x06df,ffff: Mailbox message data 423 * 0x0740,f000 - 0x0740,ffff: MCU firmware section 424 * 0x21f0,0000 - 0x21ff,ffff: pstore/ramoops buffer 425 * 0x3e00,0000 - 0x3fff,ffff: OP-TEE 426 */ 427 428 gd->bd->bi_dram[0].start = PHYS_SDRAM_1; 429 gd->bd->bi_dram[0].size = 0x05e00000; 430 431 gd->bd->bi_dram[1].start = 0x05f00000; 432 gd->bd->bi_dram[1].size = 0x00001000; 433 434 gd->bd->bi_dram[2].start = 0x05f02000; 435 gd->bd->bi_dram[2].size = 0x00efd000; 436 437 gd->bd->bi_dram[3].start = 0x06e00000; 438 gd->bd->bi_dram[3].size = 0x0060f000; 439 440 gd->bd->bi_dram[4].start = 0x07410000; 441 gd->bd->bi_dram[4].size = 0x1aaf0000; 442 443 gd->bd->bi_dram[5].start = 0x22000000; 444 gd->bd->bi_dram[5].size = 0x1c000000; 445 } 446 447 void reset_cpu(ulong addr) 448 { 449 writel(0x48698284, &ao_sc->stat0); 450 wfi(); 451 } 452