1 /* 2 * (C) Copyright 2013 3 * Gumstix Inc. <www.gumstix.com> 4 * Maintainer: Ash Charles <ash@gumstix.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 #include <common.h> 9 #include <netdev.h> 10 #include <asm/arch/sys_proto.h> 11 #include <asm/arch/mmc_host_def.h> 12 #include <twl6030.h> 13 #include <asm/emif.h> 14 #include <asm/arch/clock.h> 15 #include <asm/arch/gpio.h> 16 #include <asm/gpio.h> 17 18 #include "duovero_mux_data.h" 19 20 #define WIFI_EN 43 21 22 #if defined(CONFIG_CMD_NET) 23 #define SMSC_NRESET 45 24 static void setup_net_chip(void); 25 #endif 26 27 #ifdef CONFIG_USB_EHCI 28 #include <usb.h> 29 #include <asm/arch/ehci.h> 30 #include <asm/ehci-omap.h> 31 #endif 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 const struct omap_sysinfo sysinfo = { 36 "Board: duovero\n" 37 }; 38 39 struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000; 40 41 /** 42 * @brief board_init 43 * 44 * @return 0 45 */ 46 int board_init(void) 47 { 48 gpmc_init(); 49 50 gd->bd->bi_arch_number = MACH_TYPE_OMAP4_DUOVERO; 51 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 52 53 return 0; 54 } 55 56 /** 57 * @brief misc_init_r - Configure board specific configurations 58 * such as power configurations, ethernet initialization as phase2 of 59 * boot sequence 60 * 61 * @return 0 62 */ 63 int misc_init_r(void) 64 { 65 int ret = 0; 66 u8 val; 67 68 /* wifi setup: first enable 32Khz clock from 6030 pmic */ 69 val = 0xe1; 70 ret = i2c_write(TWL6030_CHIP_PM, 0xbe, 1, &val, 1); 71 if (ret) 72 printf("Failed to enable 32Khz clock to wifi module\n"); 73 74 /* then setup WIFI_EN as an output pin and send reset pulse */ 75 if (!gpio_request(WIFI_EN, "")) { 76 gpio_direction_output(WIFI_EN, 0); 77 gpio_set_value(WIFI_EN, 1); 78 udelay(1); 79 gpio_set_value(WIFI_EN, 0); 80 udelay(1); 81 gpio_set_value(WIFI_EN, 1); 82 } 83 84 #if defined(CONFIG_CMD_NET) 85 setup_net_chip(); 86 #endif 87 return 0; 88 } 89 90 void set_muxconf_regs(void) 91 { 92 do_set_mux((*ctrl)->control_padconf_core_base, 93 core_padconf_array_essential, 94 sizeof(core_padconf_array_essential) / 95 sizeof(struct pad_conf_entry)); 96 97 do_set_mux((*ctrl)->control_padconf_wkup_base, 98 wkup_padconf_array_essential, 99 sizeof(wkup_padconf_array_essential) / 100 sizeof(struct pad_conf_entry)); 101 102 do_set_mux((*ctrl)->control_padconf_core_base, 103 core_padconf_array_non_essential, 104 sizeof(core_padconf_array_non_essential) / 105 sizeof(struct pad_conf_entry)); 106 107 do_set_mux((*ctrl)->control_padconf_wkup_base, 108 wkup_padconf_array_non_essential, 109 sizeof(wkup_padconf_array_non_essential) / 110 sizeof(struct pad_conf_entry)); 111 } 112 113 #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) 114 int board_mmc_init(bd_t *bis) 115 { 116 return omap_mmc_init(0, 0, 0, -1, -1); 117 } 118 119 void board_mmc_power_init(void) 120 { 121 twl6030_power_mmc_init(0); 122 } 123 #endif 124 125 #if defined(CONFIG_CMD_NET) 126 127 #define GPMC_SIZE_16M 0xF 128 #define GPMC_BASEADDR_MASK 0x3F 129 #define GPMC_CS_ENABLE 0x1 130 131 static void enable_gpmc_net_config(const u32 *gpmc_config, struct gpmc_cs *cs, 132 u32 base, u32 size) 133 { 134 writel(0, &cs->config7); 135 sdelay(1000); 136 /* Delay for settling */ 137 writel(gpmc_config[0], &cs->config1); 138 writel(gpmc_config[1], &cs->config2); 139 writel(gpmc_config[2], &cs->config3); 140 writel(gpmc_config[3], &cs->config4); 141 writel(gpmc_config[4], &cs->config5); 142 writel(gpmc_config[5], &cs->config6); 143 144 /* 145 * Enable the config. size is the CS size and goes in 146 * bits 11:8. We set bit 6 to enable this CS and the base 147 * address goes into bits 5:0. 148 */ 149 writel((size << 8) | (GPMC_CS_ENABLE << 6) | 150 ((base >> 24) & GPMC_BASEADDR_MASK), 151 &cs->config7); 152 153 sdelay(2000); 154 } 155 156 /* GPMC CS configuration for an SMSC LAN9221 ethernet controller */ 157 #define NET_LAN9221_GPMC_CONFIG1 0x2a001203 158 #define NET_LAN9221_GPMC_CONFIG2 0x000a0a02 159 #define NET_LAN9221_GPMC_CONFIG3 0x00020200 160 #define NET_LAN9221_GPMC_CONFIG4 0x0a030a03 161 #define NET_LAN9221_GPMC_CONFIG5 0x000a0a0a 162 #define NET_LAN9221_GPMC_CONFIG6 0x8a070707 163 #define NET_LAN9221_GPMC_CONFIG7 0x00000f6c 164 165 /* GPMC definitions for LAN9221 chips on expansion boards */ 166 static const u32 gpmc_lan_config[] = { 167 NET_LAN9221_GPMC_CONFIG1, 168 NET_LAN9221_GPMC_CONFIG2, 169 NET_LAN9221_GPMC_CONFIG3, 170 NET_LAN9221_GPMC_CONFIG4, 171 NET_LAN9221_GPMC_CONFIG5, 172 NET_LAN9221_GPMC_CONFIG6, 173 /*CONFIG7- computed as params */ 174 }; 175 176 /* 177 * Routine: setup_net_chip 178 * Description: Setting up the configuration GPMC registers specific to the 179 * Ethernet hardware. 180 */ 181 static void setup_net_chip(void) 182 { 183 enable_gpmc_net_config(gpmc_lan_config, &gpmc_cfg->cs[5], 0x2C000000, 184 GPMC_SIZE_16M); 185 186 /* Make GPIO SMSC_NRESET as output pin and send reset pulse */ 187 if (!gpio_request(SMSC_NRESET, "")) { 188 gpio_direction_output(SMSC_NRESET, 0); 189 gpio_set_value(SMSC_NRESET, 1); 190 udelay(1); 191 gpio_set_value(SMSC_NRESET, 0); 192 udelay(1); 193 gpio_set_value(SMSC_NRESET, 1); 194 } 195 } 196 #endif 197 198 int board_eth_init(bd_t *bis) 199 { 200 int rc = 0; 201 #ifdef CONFIG_SMC911X 202 rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); 203 #endif 204 return rc; 205 } 206 207 #ifdef CONFIG_USB_EHCI 208 209 static struct omap_usbhs_board_data usbhs_bdata = { 210 .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, 211 .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, 212 .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, 213 }; 214 215 int ehci_hcd_init(int index, enum usb_init_type init, 216 struct ehci_hccr **hccr, struct ehci_hcor **hcor) 217 { 218 int ret; 219 unsigned int utmi_clk; 220 u32 auxclk, altclksrc; 221 222 /* Now we can enable our port clocks */ 223 utmi_clk = readl((void *)CM_L3INIT_HSUSBHOST_CLKCTRL); 224 utmi_clk |= HSUSBHOST_CLKCTRL_CLKSEL_UTMI_P1_MASK; 225 setbits_le32((void *)CM_L3INIT_HSUSBHOST_CLKCTRL, utmi_clk); 226 227 auxclk = readl(&scrm->auxclk3); 228 /* Select sys_clk */ 229 auxclk &= ~AUXCLK_SRCSELECT_MASK; 230 auxclk |= AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT; 231 /* Set the divisor to 2 */ 232 auxclk &= ~AUXCLK_CLKDIV_MASK; 233 auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT; 234 /* Request auxilary clock #3 */ 235 auxclk |= AUXCLK_ENABLE_MASK; 236 writel(auxclk, &scrm->auxclk3); 237 238 altclksrc = readl(&scrm->altclksrc); 239 240 /* Activate alternate system clock supplier */ 241 altclksrc &= ~ALTCLKSRC_MODE_MASK; 242 altclksrc |= ALTCLKSRC_MODE_ACTIVE; 243 244 /* enable clocks */ 245 altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK; 246 247 writel(altclksrc, &scrm->altclksrc); 248 249 ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); 250 if (ret < 0) 251 return ret; 252 253 return 0; 254 } 255 256 int ehci_hcd_stop(int index) 257 { 258 return omap_ehci_hcd_stop(); 259 } 260 #endif 261 262 /* 263 * get_board_rev() - get board revision 264 */ 265 u32 get_board_rev(void) 266 { 267 return 0x20; 268 } 269