1 /* 2 * (C) Copyright 2015 General Electric Company 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __PPD_GPIO_H_ 8 #define __PPD_GPIO_H_ 9 10 #include <asm/arch/iomux-mx53.h> 11 #include <asm/gpio.h> 12 13 #define PPD_UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \ 14 PAD_CTL_PUS_100K_UP) 15 16 static const iomux_v3_cfg_t ppd_pads[] = { 17 /* FEC */ 18 MX53_PAD_EIM_A22__GPIO2_16, 19 /* UART */ 20 NEW_PAD_CTRL(MX53_PAD_PATA_DMACK__UART1_RXD_MUX, PPD_UART_PAD_CTRL), 21 NEW_PAD_CTRL(MX53_PAD_PATA_DIOW__UART1_TXD_MUX, PPD_UART_PAD_CTRL), 22 /* Video */ 23 MX53_PAD_CSI0_DATA_EN__GPIO5_20, /* LR_SCAN_CTRL */ 24 MX53_PAD_CSI0_VSYNC__GPIO5_21, /* UD_SCAN_CTRL */ 25 MX53_PAD_CSI0_DAT10__GPIO5_28, /* DATA_WIDTH_CTRL */ 26 MX53_PAD_CSI0_PIXCLK__GPIO5_18, /* HOST_CONTROLLED_RESET_TO_LCD_N */ 27 MX53_PAD_EIM_DA2__GPIO3_2, /* LVDS1_MUX_CTRL */ 28 MX53_PAD_EIM_DA3__GPIO3_3, /* LVDS0_MUX_CTRL */ 29 MX53_PAD_EIM_A21__GPIO2_17, /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */ 30 MX53_PAD_CSI0_DAT11__GPIO5_29, /* BACKLIGHT_ENABLE */ 31 MX53_PAD_DISP0_DAT9__PWM2_PWMO, /* IMX535_PWM2_TO_LCD_CONNECTOR */ 32 /* I2C */ 33 MX53_PAD_EIM_A20__GPIO2_18, /* RESET_I2C1_BUS_SEGMENT_MUX_N */ 34 35 /* SPI */ 36 MX53_PAD_DISP0_DAT23__GPIO5_17, 37 MX53_PAD_KEY_COL2__GPIO4_10, 38 MX53_PAD_KEY_ROW2__GPIO4_11, 39 MX53_PAD_KEY_COL3__GPIO4_12, 40 }; 41 42 struct gpio_cfg { 43 unsigned int gpio; 44 int value; 45 }; 46 47 #define RESET_IMX535_ETHERNET_PHY_N IMX_GPIO_NR(2, 16) 48 #define UD_SCAN_CTRL IMX_GPIO_NR(5, 21) 49 #define LR_SCAN_CTRL IMX_GPIO_NR(5, 20) 50 #define LVDS0_MUX_CTRL IMX_GPIO_NR(3, 3) 51 #define LVDS1_MUX_CTRL IMX_GPIO_NR(3, 2) 52 #define HOST_CONTROLLED_RESET_TO_LCD_N IMX_GPIO_NR(5, 18) 53 #define DATA_WIDTH_CTRL IMX_GPIO_NR(5, 28) 54 #define RESET_DP0_TRANSMITTER_N IMX_GPIO_NR(2, 28) 55 #define RESET_DP1_TRANSMITTER_N IMX_GPIO_NR(2, 29) 56 #define POWER_DOWN_LVDS0_DESERIALIZER_N IMX_GPIO_NR(2, 22) 57 #define POWER_DOWN_LVDS1_DESERIALIZER_N IMX_GPIO_NR(2, 27) 58 #define ENABLE_PWR_TO_LCD_AND_UI_INTERFACE IMX_GPIO_NR(2, 17) 59 #define BACKLIGHT_ENABLE IMX_GPIO_NR(5, 29) 60 #define RESET_I2C1_BUS_SEGMENT_MUX_N IMX_GPIO_NR(2, 18) 61 #define ECSPI1_CS0 IMX_GPIO_NR(5, 17) 62 #define ECSPI1_CS1 IMX_GPIO_NR(4, 10) 63 #define ECSPI1_CS2 IMX_GPIO_NR(4, 11) 64 #define ECSPI1_CS3 IMX_GPIO_NR(4, 12) 65 66 static const struct gpio_cfg ppd_gpios[] = { 67 /* FEC */ 68 /* Drive Low as GPIO output for 25ms per Eth Phy IX spec */ 69 /* Then Drive High as GPIO output to bring Eth Phy IC out of reset */ 70 { RESET_IMX535_ETHERNET_PHY_N, 0 }, 71 { RESET_IMX535_ETHERNET_PHY_N, 1 }, 72 /* Video */ 73 { UD_SCAN_CTRL, 0 }, 74 { LR_SCAN_CTRL, 1 }, 75 #ifdef PROPRIETARY_CHANGES 76 { LVDS0_MUX_CTRL, 1 }, 77 #else 78 { LVDS0_MUX_CTRL, 0 }, 79 #endif 80 { LVDS1_MUX_CTRL, 1 }, 81 { HOST_CONTROLLED_RESET_TO_LCD_N, 1 }, 82 { DATA_WIDTH_CTRL, 0 }, 83 { RESET_DP0_TRANSMITTER_N, 1 }, 84 { RESET_DP1_TRANSMITTER_N, 1 }, 85 { POWER_DOWN_LVDS0_DESERIALIZER_N, 1 }, 86 { POWER_DOWN_LVDS1_DESERIALIZER_N, 1 }, 87 { ENABLE_PWR_TO_LCD_AND_UI_INTERFACE, 1 }, 88 { BACKLIGHT_ENABLE, 0 }, 89 { RESET_I2C1_BUS_SEGMENT_MUX_N, 1 }, 90 { ECSPI1_CS0, 1 }, 91 { ECSPI1_CS1, 1 }, 92 { ECSPI1_CS2, 1 }, 93 { ECSPI1_CS3, 1 }, 94 }; 95 96 #endif /* __PPD_GPIO_H_ */ 97