1 /* 2 * Copyright 2015 Timesys Corporation 3 * Copyright 2015 General Electric Company 4 * Copyright 2012 Freescale Semiconductor, Inc. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <asm/arch/clock.h> 10 #include <asm/arch/imx-regs.h> 11 #include <asm/arch/iomux.h> 12 #include <asm/arch/mx6-pins.h> 13 #include <asm/errno.h> 14 #include <asm/gpio.h> 15 #include <asm/imx-common/mxc_i2c.h> 16 #include <asm/imx-common/iomux-v3.h> 17 #include <asm/imx-common/boot_mode.h> 18 #include <asm/imx-common/video.h> 19 #include <mmc.h> 20 #include <fsl_esdhc.h> 21 #include <miiphy.h> 22 #include <netdev.h> 23 #include <asm/arch/mxc_hdmi.h> 24 #include <asm/arch/crm_regs.h> 25 #include <asm/io.h> 26 #include <asm/arch/sys_proto.h> 27 #include <i2c.h> 28 #include <pwm.h> 29 DECLARE_GLOBAL_DATA_PTR; 30 31 #define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 32 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 33 PAD_CTL_HYS) 34 35 #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 36 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 37 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 38 39 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ 40 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ 41 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 42 43 #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ 44 PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST) 45 46 #define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ 47 PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) 48 49 #define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 50 PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) 51 52 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ 53 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 54 55 #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 56 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 57 PAD_CTL_ODE | PAD_CTL_SRE_FAST) 58 59 #define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL) 60 61 int dram_init(void) 62 { 63 gd->ram_size = imx_ddr_size(); 64 65 return 0; 66 } 67 68 static iomux_v3_cfg_t const uart3_pads[] = { 69 MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 70 MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 71 MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 72 MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 73 }; 74 75 static iomux_v3_cfg_t const uart4_pads[] = { 76 MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 77 MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 78 }; 79 80 static iomux_v3_cfg_t const enet_pads[] = { 81 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 82 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 83 MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 84 MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 85 MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 86 MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 87 MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 88 MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 89 MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL), 90 MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 91 MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 92 MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 93 MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 94 MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 95 MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 96 /* AR8033 PHY Reset */ 97 MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), 98 }; 99 100 static void setup_iomux_enet(void) 101 { 102 imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); 103 104 /* Reset AR8033 PHY */ 105 gpio_direction_output(IMX_GPIO_NR(1, 28), 0); 106 udelay(500); 107 gpio_set_value(IMX_GPIO_NR(1, 28), 1); 108 } 109 110 static iomux_v3_cfg_t const usdhc2_pads[] = { 111 MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 112 MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 113 MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 114 MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 115 MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 116 MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 117 MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), 118 }; 119 120 static iomux_v3_cfg_t const usdhc3_pads[] = { 121 MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 122 MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 123 MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL), 124 MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 125 MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 126 MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 127 MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 128 MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 129 MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 130 MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 131 MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 132 }; 133 134 static iomux_v3_cfg_t const usdhc4_pads[] = { 135 MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 136 MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 137 MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 138 MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 139 MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 140 MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 141 MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 142 MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 143 MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 144 MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 145 MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), 146 MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), 147 }; 148 149 static iomux_v3_cfg_t const ecspi1_pads[] = { 150 MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), 151 MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), 152 MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), 153 MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), 154 }; 155 156 static struct i2c_pads_info i2c_pad_info1 = { 157 .scl = { 158 .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD, 159 .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD, 160 .gp = IMX_GPIO_NR(5, 27) 161 }, 162 .sda = { 163 .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD, 164 .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD, 165 .gp = IMX_GPIO_NR(5, 26) 166 } 167 }; 168 169 static struct i2c_pads_info i2c_pad_info2 = { 170 .scl = { 171 .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD, 172 .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD, 173 .gp = IMX_GPIO_NR(4, 12) 174 }, 175 .sda = { 176 .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD, 177 .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD, 178 .gp = IMX_GPIO_NR(4, 13) 179 } 180 }; 181 182 static struct i2c_pads_info i2c_pad_info3 = { 183 .scl = { 184 .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD, 185 .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD, 186 .gp = IMX_GPIO_NR(1, 3) 187 }, 188 .sda = { 189 .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD, 190 .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD, 191 .gp = IMX_GPIO_NR(1, 6) 192 } 193 }; 194 195 #ifdef CONFIG_MXC_SPI 196 int board_spi_cs_gpio(unsigned bus, unsigned cs) 197 { 198 return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1; 199 } 200 201 static void setup_spi(void) 202 { 203 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); 204 } 205 #endif 206 207 static iomux_v3_cfg_t const pcie_pads[] = { 208 MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), 209 MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), 210 }; 211 212 static void setup_pcie(void) 213 { 214 imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads)); 215 } 216 217 static void setup_iomux_uart(void) 218 { 219 imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads)); 220 imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads)); 221 } 222 223 #ifdef CONFIG_FSL_ESDHC 224 struct fsl_esdhc_cfg usdhc_cfg[3] = { 225 {USDHC2_BASE_ADDR}, 226 {USDHC3_BASE_ADDR}, 227 {USDHC4_BASE_ADDR}, 228 }; 229 230 #define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4) 231 #define USDHC4_CD_GPIO IMX_GPIO_NR(6, 11) 232 233 int board_mmc_getcd(struct mmc *mmc) 234 { 235 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 236 int ret = 0; 237 238 switch (cfg->esdhc_base) { 239 case USDHC2_BASE_ADDR: 240 ret = !gpio_get_value(USDHC2_CD_GPIO); 241 break; 242 case USDHC3_BASE_ADDR: 243 ret = 1; /* eMMC is always present */ 244 break; 245 case USDHC4_BASE_ADDR: 246 ret = !gpio_get_value(USDHC4_CD_GPIO); 247 break; 248 } 249 250 return ret; 251 } 252 253 int board_mmc_init(bd_t *bis) 254 { 255 int ret; 256 int i; 257 258 for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { 259 switch (i) { 260 case 0: 261 imx_iomux_v3_setup_multiple_pads( 262 usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); 263 gpio_direction_input(USDHC2_CD_GPIO); 264 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 265 break; 266 case 1: 267 imx_iomux_v3_setup_multiple_pads( 268 usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); 269 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 270 break; 271 case 2: 272 imx_iomux_v3_setup_multiple_pads( 273 usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); 274 gpio_direction_input(USDHC4_CD_GPIO); 275 usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); 276 break; 277 default: 278 printf("Warning: you configured more USDHC controllers\n" 279 "(%d) then supported by the board (%d)\n", 280 i + 1, CONFIG_SYS_FSL_USDHC_NUM); 281 return -EINVAL; 282 } 283 284 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); 285 if (ret) 286 return ret; 287 } 288 289 return 0; 290 } 291 #endif 292 293 static int mx6_rgmii_rework(struct phy_device *phydev) 294 { 295 /* Configure AR8033 to ouput a 125MHz clk from CLK_25M */ 296 /* set device address 0x7 */ 297 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); 298 /* offset 0x8016: CLK_25M Clock Select */ 299 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); 300 /* enable register write, no post increment, address 0x7 */ 301 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); 302 /* set to 125 MHz from local PLL source */ 303 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18); 304 305 /* rgmii tx clock delay enable */ 306 /* set debug port address: SerDes Test and System Mode Control */ 307 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); 308 /* enable rgmii tx clock delay */ 309 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); 310 311 return 0; 312 } 313 314 int board_phy_config(struct phy_device *phydev) 315 { 316 mx6_rgmii_rework(phydev); 317 318 if (phydev->drv->config) 319 phydev->drv->config(phydev); 320 321 return 0; 322 } 323 324 #if defined(CONFIG_VIDEO_IPUV3) 325 static iomux_v3_cfg_t const backlight_pads[] = { 326 /* Power for LVDS Display */ 327 MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL), 328 #define LVDS_POWER_GP IMX_GPIO_NR(3, 22) 329 /* Backlight enable for LVDS display */ 330 MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), 331 #define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0) 332 /* backlight PWM brightness control */ 333 MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), 334 }; 335 336 static void do_enable_hdmi(struct display_info_t const *dev) 337 { 338 imx_enable_hdmi_phy(); 339 } 340 341 int board_cfb_skip(void) 342 { 343 gpio_direction_output(LVDS_POWER_GP, 1); 344 345 return 0; 346 } 347 348 static int detect_baseboard(struct display_info_t const *dev) 349 { 350 if (IS_ENABLED(CONFIG_TARGET_GE_B450V3) || 351 IS_ENABLED(CONFIG_TARGET_GE_B650V3)) 352 return 1; 353 354 return 0; 355 } 356 357 struct display_info_t const displays[] = {{ 358 .bus = -1, 359 .addr = -1, 360 .pixfmt = IPU_PIX_FMT_RGB24, 361 .detect = detect_baseboard, 362 .enable = NULL, 363 .mode = { 364 .name = "G121X1-L03", 365 .refresh = 60, 366 .xres = 1024, 367 .yres = 768, 368 .pixclock = 15385, 369 .left_margin = 20, 370 .right_margin = 300, 371 .upper_margin = 30, 372 .lower_margin = 8, 373 .hsync_len = 1, 374 .vsync_len = 1, 375 .sync = FB_SYNC_EXT, 376 .vmode = FB_VMODE_NONINTERLACED 377 } }, { 378 .bus = -1, 379 .addr = 3, 380 .pixfmt = IPU_PIX_FMT_RGB24, 381 .detect = detect_hdmi, 382 .enable = do_enable_hdmi, 383 .mode = { 384 .name = "HDMI", 385 .refresh = 60, 386 .xres = 1024, 387 .yres = 768, 388 .pixclock = 15385, 389 .left_margin = 220, 390 .right_margin = 40, 391 .upper_margin = 21, 392 .lower_margin = 7, 393 .hsync_len = 60, 394 .vsync_len = 10, 395 .sync = FB_SYNC_EXT, 396 .vmode = FB_VMODE_NONINTERLACED 397 } } }; 398 size_t display_count = ARRAY_SIZE(displays); 399 400 static void enable_videopll(void) 401 { 402 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 403 s32 timeout = 100000; 404 405 setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN); 406 407 /* set video pll to 910MHz (24MHz * (37+11/12)) 408 * video pll post div to 910/4 = 227.5MHz 409 */ 410 clrsetbits_le32(&ccm->analog_pll_video, 411 BM_ANADIG_PLL_VIDEO_DIV_SELECT | 412 BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT, 413 BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) | 414 BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0)); 415 416 writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num); 417 writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom); 418 419 clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN); 420 421 while (timeout--) 422 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) 423 break; 424 425 if (timeout < 0) 426 printf("Warning: video pll lock timeout!\n"); 427 428 clrsetbits_le32(&ccm->analog_pll_video, 429 BM_ANADIG_PLL_VIDEO_BYPASS, 430 BM_ANADIG_PLL_VIDEO_ENABLE); 431 } 432 433 static void setup_display_b850v3(void) 434 { 435 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 436 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 437 438 enable_videopll(); 439 440 /* IPU1 D0 clock is 227.5 / 3.5 = 65MHz */ 441 clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); 442 443 imx_setup_hdmi(); 444 445 /* Set LDB_DI0 as clock source for IPU_DI0 */ 446 clrsetbits_le32(&mxc_ccm->chsccdr, 447 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK, 448 (CHSCCDR_CLK_SEL_LDB_DI0 << 449 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); 450 451 /* Turn on IPU LDB DI0 clocks */ 452 setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); 453 454 enable_ipu_clock(); 455 456 writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | 457 IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW | 458 IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | 459 IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG | 460 IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT | 461 IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | 462 IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT | 463 IOMUXC_GPR2_SPLIT_MODE_EN_MASK | 464 IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 | 465 IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0, 466 &iomux->gpr[2]); 467 468 clrbits_le32(&iomux->gpr[3], 469 IOMUXC_GPR3_LVDS0_MUX_CTL_MASK | 470 IOMUXC_GPR3_LVDS1_MUX_CTL_MASK | 471 IOMUXC_GPR3_HDMI_MUX_CTL_MASK); 472 } 473 474 static void setup_display_bx50v3(void) 475 { 476 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 477 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 478 479 /* When a reset/reboot is performed the display power needs to be turned 480 * off for atleast 500ms. The boot time is ~300ms, we need to wait for 481 * an additional 200ms here. Unfortunately we use external PMIC for 482 * doing the reset, so can not differentiate between POR vs soft reset 483 */ 484 mdelay(200); 485 486 /* IPU1 DI0 clock is 480/7 = 68.5 MHz */ 487 setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); 488 489 /* Set LDB_DI0 as clock source for IPU_DI0 */ 490 clrsetbits_le32(&mxc_ccm->chsccdr, 491 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK, 492 (CHSCCDR_CLK_SEL_LDB_DI0 << 493 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); 494 495 /* Turn on IPU LDB DI0 clocks */ 496 setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); 497 498 enable_ipu_clock(); 499 500 writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | 501 IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | 502 IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | 503 IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT | 504 IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0, 505 &iomux->gpr[2]); 506 507 clrsetbits_le32(&iomux->gpr[3], 508 IOMUXC_GPR3_LVDS0_MUX_CTL_MASK, 509 (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 << 510 IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)); 511 512 /* backlights off until needed */ 513 imx_iomux_v3_setup_multiple_pads(backlight_pads, 514 ARRAY_SIZE(backlight_pads)); 515 gpio_direction_input(LVDS_POWER_GP); 516 gpio_direction_input(LVDS_BACKLIGHT_GP); 517 } 518 #endif /* CONFIG_VIDEO_IPUV3 */ 519 520 /* 521 * Do not overwrite the console 522 * Use always serial for U-Boot console 523 */ 524 int overwrite_console(void) 525 { 526 return 1; 527 } 528 529 int board_eth_init(bd_t *bis) 530 { 531 setup_iomux_enet(); 532 setup_pcie(); 533 534 return cpu_eth_init(bis); 535 } 536 537 static iomux_v3_cfg_t const misc_pads[] = { 538 MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), 539 MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL), 540 MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL), 541 MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL), 542 MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL), 543 MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL), 544 MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL), 545 }; 546 #define SUS_S3_OUT IMX_GPIO_NR(4, 11) 547 #define WIFI_EN IMX_GPIO_NR(6, 14) 548 549 int board_early_init_f(void) 550 { 551 imx_iomux_v3_setup_multiple_pads(misc_pads, 552 ARRAY_SIZE(misc_pads)); 553 554 setup_iomux_uart(); 555 556 #if defined(CONFIG_VIDEO_IPUV3) 557 if (IS_ENABLED(CONFIG_TARGET_GE_B850V3)) 558 /* Set LDB clock to Video PLL */ 559 select_ldb_di_clock_source(MXC_PLL5_CLK); 560 else 561 /* Set LDB clock to USB PLL */ 562 select_ldb_di_clock_source(MXC_PLL3_SW_CLK); 563 #endif 564 return 0; 565 } 566 567 int board_init(void) 568 { 569 gpio_direction_output(SUS_S3_OUT, 1); 570 gpio_direction_output(WIFI_EN, 1); 571 #if defined(CONFIG_VIDEO_IPUV3) 572 if (IS_ENABLED(CONFIG_TARGET_GE_B850V3)) 573 setup_display_b850v3(); 574 else 575 setup_display_bx50v3(); 576 #endif 577 /* address of boot parameters */ 578 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 579 580 #ifdef CONFIG_MXC_SPI 581 setup_spi(); 582 #endif 583 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); 584 setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); 585 setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); 586 587 return 0; 588 } 589 590 #ifdef CONFIG_CMD_BMODE 591 static const struct boot_mode board_boot_modes[] = { 592 /* 4 bit bus width */ 593 {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, 594 {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, 595 {NULL, 0}, 596 }; 597 #endif 598 599 int board_late_init(void) 600 { 601 #ifdef CONFIG_CMD_BMODE 602 add_board_boot_modes(board_boot_modes); 603 #endif 604 605 #ifdef CONFIG_VIDEO_IPUV3 606 /* We need at least 200ms between power on and backlight on 607 * as per specifications from CHI MEI */ 608 mdelay(250); 609 610 /* enable backlight PWM 1 */ 611 pwm_init(0, 0, 0); 612 613 /* duty cycle 5000000ns, period: 5000000ns */ 614 pwm_config(0, 5000000, 5000000); 615 616 /* Backlight Power */ 617 gpio_direction_output(LVDS_BACKLIGHT_GP, 1); 618 619 pwm_enable(0); 620 #endif 621 622 return 0; 623 } 624 625 int checkboard(void) 626 { 627 printf("BOARD: %s\n", CONFIG_BOARD_NAME); 628 return 0; 629 } 630