1 /*
2  * Copyright (C) 2015 Stefan Roese <sr@denx.de>
3  * Copyright (C) 2016 Mario Six <mario.six@gdsys.cc>
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 #include <common.h>
9 #include <dm.h>
10 #include <miiphy.h>
11 #include <tpm.h>
12 #include <asm/io.h>
13 #include <asm/arch/cpu.h>
14 #include <asm-generic/gpio.h>
15 
16 #include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
17 #include "../arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.h"
18 
19 #include "keyprogram.h"
20 #include "dt_helpers.h"
21 #include "hydra.h"
22 #include "ihs_phys.h"
23 
24 DECLARE_GLOBAL_DATA_PTR;
25 
26 #define ETH_PHY_CTRL_REG		0
27 #define ETH_PHY_CTRL_POWER_DOWN_BIT	11
28 #define ETH_PHY_CTRL_POWER_DOWN_MASK	(1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
29 
30 #define DB_GP_88F68XX_GPP_OUT_ENA_LOW	0x7fffffff
31 #define DB_GP_88F68XX_GPP_OUT_ENA_MID	0xffffefff
32 
33 #define DB_GP_88F68XX_GPP_OUT_VAL_LOW	0x0
34 #define DB_GP_88F68XX_GPP_OUT_VAL_MID	0x00001000
35 #define DB_GP_88F68XX_GPP_POL_LOW	0x0
36 #define DB_GP_88F68XX_GPP_POL_MID	0x0
37 
38 /*
39  * Define the DDR layout / topology here in the board file. This will
40  * be used by the DDR3 init code in the SPL U-Boot version to configure
41  * the DDR3 controller.
42  */
43 static struct hws_topology_map ddr_topology_map = {
44 	0x1, /* active interfaces */
45 	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
46 	{ { { {0x1, 0, 0, 0},
47 	      {0x1, 0, 0, 0},
48 	      {0x1, 0, 0, 0},
49 	      {0x1, 0, 0, 0},
50 	      {0x1, 0, 0, 0} },
51 	    SPEED_BIN_DDR_1600K,	/* speed_bin */
52 	    BUS_WIDTH_16,		/* memory_width */
53 	    MEM_4G,			/* mem_size */
54 	    DDR_FREQ_533,		/* frequency */
55 	    0, 0,			/* cas_wl cas_l */
56 	    HWS_TEMP_LOW,		/* temperature */
57 	    HWS_TIM_DEFAULT} },		/* timing */
58 	5,				/* Num Of Bus Per Interface*/
59 	BUS_MASK_32BIT			/* Busses mask */
60 };
61 
62 static struct serdes_map serdes_topology_map[] = {
63 	{SGMII0, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
64 	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
65 	/* SATA tx polarity is inverted */
66 	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 1},
67 	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
68 	{DEFAULT_SERDES, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
69 	{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
70 };
71 
72 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
73 {
74 	*serdes_map_array = serdes_topology_map;
75 	*count = ARRAY_SIZE(serdes_topology_map);
76 	return 0;
77 }
78 
79 void board_pex_config(void)
80 {
81 #ifdef CONFIG_SPL_BUILD
82 	uint k;
83 	struct gpio_desc gpio = {};
84 
85 	if (!request_gpio_by_name(&gpio, "pca9698@22", 31, "fpga-program-gpio")) {
86 		/* prepare FPGA reconfiguration */
87 		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
88 		dm_gpio_set_value(&gpio, 0);
89 
90 		/* give lunatic PCIe clock some time to stabilize */
91 		mdelay(500);
92 
93 		/* start FPGA reconfiguration */
94 		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_IN);
95 	}
96 
97 	/* wait for FPGA done */
98 	if (!request_gpio_by_name(&gpio, "pca9698@22", 19, "fpga-done-gpio")) {
99 		for (k = 0; k < 20; ++k) {
100 			if (dm_gpio_get_value(&gpio)) {
101 				printf("FPGA done after %u rounds\n", k);
102 				break;
103 			}
104 			mdelay(100);
105 		}
106 	}
107 
108 	/* disable FPGA reset */
109 	if (!request_gpio_by_name(&gpio, "gpio@18100", 6, "cpu-to-fpga-reset")) {
110 		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
111 		dm_gpio_set_value(&gpio, 1);
112 	}
113 
114 	/* wait for FPGA ready */
115 	if (!request_gpio_by_name(&gpio, "pca9698@22", 27, "fpga-ready-gpio")) {
116 		for (k = 0; k < 2; ++k) {
117 			if (!dm_gpio_get_value(&gpio))
118 				break;
119 			mdelay(100);
120 		}
121 	}
122 #endif
123 }
124 
125 struct hws_topology_map *ddr3_get_topology_map(void)
126 {
127 	return &ddr_topology_map;
128 }
129 
130 int board_early_init_f(void)
131 {
132 #ifdef CONFIG_SPL_BUILD
133 	/* Configure MPP */
134 	writel(0x00111111, MVEBU_MPP_BASE + 0x00);
135 	writel(0x40040000, MVEBU_MPP_BASE + 0x04);
136 	writel(0x00466444, MVEBU_MPP_BASE + 0x08);
137 	writel(0x00043300, MVEBU_MPP_BASE + 0x0c);
138 	writel(0x44400000, MVEBU_MPP_BASE + 0x10);
139 	writel(0x20000334, MVEBU_MPP_BASE + 0x14);
140 	writel(0x40000000, MVEBU_MPP_BASE + 0x18);
141 	writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
142 
143 	/* Set GPP Out value */
144 	writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
145 	writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
146 
147 	/* Set GPP Polarity */
148 	writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
149 	writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
150 
151 	/* Set GPP Out Enable */
152 	writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
153 	writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
154 #endif
155 
156 	return 0;
157 }
158 
159 int board_init(void)
160 {
161 	/* Address of boot parameters */
162 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
163 
164 	return 0;
165 }
166 
167 #ifndef CONFIG_SPL_BUILD
168 void init_host_phys(struct mii_dev *bus)
169 {
170 	uint k;
171 
172 	for (k = 0; k < 2; ++k) {
173 		struct phy_device *phydev;
174 
175 		phydev = phy_find_by_mask(bus, 1 << k,
176 					  PHY_INTERFACE_MODE_SGMII);
177 
178 		if (phydev)
179 			phy_config(phydev);
180 	}
181 }
182 
183 int ccdc_eth_init(void)
184 {
185 	uint k;
186 	uint octo_phy_mask = 0;
187 	int ret;
188 	struct mii_dev *bus;
189 
190 	/* Init SoC's phys */
191 	bus = miiphy_get_dev_by_name("ethernet@34000");
192 
193 	if (bus)
194 		init_host_phys(bus);
195 
196 	bus = miiphy_get_dev_by_name("ethernet@70000");
197 
198 	if (bus)
199 		init_host_phys(bus);
200 
201 	/* Init octo phys */
202 	octo_phy_mask = calculate_octo_phy_mask();
203 
204 	printf("IHS PHYS: %08x", octo_phy_mask);
205 
206 	ret = init_octo_phys(octo_phy_mask);
207 
208 	if (ret)
209 		return ret;
210 
211 	printf("\n");
212 
213 	if (!get_fpga()) {
214 		puts("fpga was NULL\n");
215 		return 1;
216 	}
217 
218 	/* reset all FPGA-QSGMII instances */
219 	for (k = 0; k < 80; ++k)
220 		writel(1 << 31, get_fpga()->qsgmii_port_state[k]);
221 
222 	udelay(100);
223 
224 	for (k = 0; k < 80; ++k)
225 		writel(0, get_fpga()->qsgmii_port_state[k]);
226 	return 0;
227 }
228 
229 #endif
230 
231 int board_late_init(void)
232 {
233 #ifndef CONFIG_SPL_BUILD
234 	hydra_initialize();
235 #endif
236 	return 0;
237 }
238 
239 int board_fix_fdt(void *rw_fdt_blob)
240 {
241 	struct udevice *bus = NULL;
242 	uint k;
243 	char name[64];
244 	int err;
245 
246 	err = uclass_get_device_by_name(UCLASS_I2C, "i2c@11000", &bus);
247 
248 	if (err) {
249 		printf("Could not get I2C bus.\n");
250 		return err;
251 	}
252 
253 	for (k = 0x21; k <= 0x26; k++) {
254 		snprintf(name, 64,
255 			 "/soc/internal-regs/i2c@11000/pca9698@%02x", k);
256 
257 		if (!dm_i2c_simple_probe(bus, k))
258 			fdt_disable_by_ofname(rw_fdt_blob, name);
259 	}
260 
261 	return 0;
262 }
263 
264 int last_stage_init(void)
265 {
266 #ifndef CONFIG_SPL_BUILD
267 	ccdc_eth_init();
268 #endif
269 	if (tpm_init() || tpm_startup(TPM_ST_CLEAR) ||
270 	    tpm_continue_self_test()) {
271 		return 1;
272 	}
273 
274 	mdelay(37);
275 
276 	flush_keys();
277 	load_and_run_keyprog();
278 
279 	return 0;
280 }
281