1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <i2c.h> 9 #include <hwconfig.h> 10 #include <asm/mmu.h> 11 #include <fsl_ddr_sdram.h> 12 #include <fsl_ddr_dimm_params.h> 13 #include <asm/fsl_law.h> 14 #include "ddr.h" 15 16 DECLARE_GLOBAL_DATA_PTR; 17 18 void fsl_ddr_board_options(memctl_options_t *popts, 19 dimm_params_t *pdimm, 20 unsigned int ctrl_num) 21 { 22 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 23 ulong ddr_freq; 24 25 if (ctrl_num > 2) { 26 printf("Not supported controller number %d\n", ctrl_num); 27 return; 28 } 29 if (!pdimm->n_ranks) 30 return; 31 32 /* 33 * we use identical timing for all slots. If needed, change the code 34 * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num]; 35 */ 36 if (popts->registered_dimm_en) 37 pbsp = rdimms[0]; 38 else 39 pbsp = udimms[0]; 40 41 42 /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr 43 * freqency and n_banks specified in board_specific_parameters table. 44 */ 45 ddr_freq = get_ddr_freq(0) / 1000000; 46 while (pbsp->datarate_mhz_high) { 47 if (pbsp->n_ranks == pdimm->n_ranks && 48 (pdimm->rank_density >> 30) >= pbsp->rank_gb) { 49 if (ddr_freq <= pbsp->datarate_mhz_high) { 50 popts->clk_adjust = pbsp->clk_adjust; 51 popts->wrlvl_start = pbsp->wrlvl_start; 52 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 53 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 54 goto found; 55 } 56 pbsp_highest = pbsp; 57 } 58 pbsp++; 59 } 60 61 if (pbsp_highest) { 62 printf("Error: board specific timing not found for data\n" 63 "rate %lu MT/s\n" 64 "Trying to use the highest speed (%u) parameters\n", 65 ddr_freq, pbsp_highest->datarate_mhz_high); 66 popts->clk_adjust = pbsp_highest->clk_adjust; 67 popts->wrlvl_start = pbsp_highest->wrlvl_start; 68 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 69 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 70 } else { 71 panic("DIMM is not supported by this board"); 72 } 73 found: 74 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" 75 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n" 76 "wrlvl_ctrl_3 0x%x\n", 77 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, 78 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, 79 pbsp->wrlvl_ctl_3); 80 81 /* 82 * Factors to consider for half-strength driver enable: 83 * - number of DIMMs installed 84 */ 85 popts->half_strength_driver_enable = 0; 86 /* 87 * Write leveling override 88 */ 89 popts->wrlvl_override = 1; 90 popts->wrlvl_sample = 0xf; 91 92 /* 93 * Rtt and Rtt_WR override 94 */ 95 popts->rtt_override = 0; 96 97 /* Enable ZQ calibration */ 98 popts->zq_en = 1; 99 100 /* DHC_EN =1, ODT = 75 Ohm */ 101 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); 102 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); 103 104 /* optimize cpo for erratum A-009942 */ 105 popts->cpo_sample = 0x64; 106 } 107 108 int initdram(void) 109 { 110 phys_size_t dram_size; 111 112 puts("Initializing....using SPD\n"); 113 114 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) 115 dram_size = fsl_ddr_sdram(); 116 #else 117 /* DDR has been initialised by first stage boot loader */ 118 dram_size = fsl_ddr_sdram_size(); 119 #endif 120 dram_size = setup_ddr_tlbs(dram_size / 0x100000); 121 dram_size *= 0x100000; 122 123 gd->ram_size = dram_size; 124 125 return 0; 126 } 127