1 /* 2 * Copyright 2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0 5 */ 6 7 #include <common.h> 8 #include <i2c.h> 9 #include <hwconfig.h> 10 #include <asm/mmu.h> 11 #include <fsl_ddr_sdram.h> 12 #include <fsl_ddr_dimm_params.h> 13 #include <asm/fsl_law.h> 14 #include "ddr.h" 15 16 DECLARE_GLOBAL_DATA_PTR; 17 18 void fsl_ddr_board_options(memctl_options_t *popts, 19 dimm_params_t *pdimm, 20 unsigned int ctrl_num) 21 { 22 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 23 ulong ddr_freq; 24 25 if (ctrl_num > 2) { 26 printf("Not supported controller number %d\n", ctrl_num); 27 return; 28 } 29 if (!pdimm->n_ranks) 30 return; 31 32 /* 33 * we use identical timing for all slots. If needed, change the code 34 * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num]; 35 */ 36 if (popts->registered_dimm_en) 37 pbsp = rdimms[0]; 38 else 39 pbsp = udimms[0]; 40 41 42 /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr 43 * freqency and n_banks specified in board_specific_parameters table. 44 */ 45 ddr_freq = get_ddr_freq(0) / 1000000; 46 while (pbsp->datarate_mhz_high) { 47 if (pbsp->n_ranks == pdimm->n_ranks && 48 (pdimm->rank_density >> 30) >= pbsp->rank_gb) { 49 if (ddr_freq <= pbsp->datarate_mhz_high) { 50 popts->cpo_override = pbsp->cpo; 51 popts->write_data_delay = 52 pbsp->write_data_delay; 53 popts->clk_adjust = pbsp->clk_adjust; 54 popts->wrlvl_start = pbsp->wrlvl_start; 55 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 56 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 57 popts->twot_en = pbsp->force_2t; 58 goto found; 59 } 60 pbsp_highest = pbsp; 61 } 62 pbsp++; 63 } 64 65 if (pbsp_highest) { 66 printf("Error: board specific timing not found " 67 "for data rate %lu MT/s\n" 68 "Trying to use the highest speed (%u) parameters\n", 69 ddr_freq, pbsp_highest->datarate_mhz_high); 70 popts->cpo_override = pbsp_highest->cpo; 71 popts->write_data_delay = pbsp_highest->write_data_delay; 72 popts->clk_adjust = pbsp_highest->clk_adjust; 73 popts->wrlvl_start = pbsp_highest->wrlvl_start; 74 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 75 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 76 popts->twot_en = pbsp_highest->force_2t; 77 } else { 78 panic("DIMM is not supported by this board"); 79 } 80 found: 81 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" 82 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " 83 "wrlvl_ctrl_3 0x%x\n", 84 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, 85 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, 86 pbsp->wrlvl_ctl_3); 87 88 /* 89 * Factors to consider for half-strength driver enable: 90 * - number of DIMMs installed 91 */ 92 popts->half_strength_driver_enable = 0; 93 /* 94 * Write leveling override 95 */ 96 popts->wrlvl_override = 1; 97 popts->wrlvl_sample = 0xf; 98 99 /* 100 * Rtt and Rtt_WR override 101 */ 102 popts->rtt_override = 0; 103 104 /* Enable ZQ calibration */ 105 popts->zq_en = 1; 106 107 /* DHC_EN =1, ODT = 75 Ohm */ 108 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); 109 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); 110 111 /* optimize cpo for erratum A-009942 */ 112 popts->cpo_sample = 0x63; 113 } 114 115 int initdram(void) 116 { 117 phys_size_t dram_size; 118 119 puts("Initializing....using SPD\n"); 120 121 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) 122 dram_size = fsl_ddr_sdram(); 123 #else 124 /* DDR has been initialised by first stage boot loader */ 125 dram_size = fsl_ddr_sdram_size(); 126 #endif 127 dram_size = setup_ddr_tlbs(dram_size / 0x100000); 128 dram_size *= 0x100000; 129 130 gd->ram_size = dram_size; 131 132 return 0; 133 } 134