1Overview 2-------- 3The T4240QDS is a high-performance computing evaluation, development and test 4platform supporting the T4240 QorIQ™ Power Architecture™ processor. T4240QDS is 5optimized to support the high-bandwidth DDR3 memory ports, as well as the 6highly-configurable SerDes ports. The system is lead-free and RoHS-compliant. 7 8Board Features 9 SERDES Connections 10 32 lanes grouped into four 8-lane banks 11 Two “front side” banks dedicated to Ethernet 12 - High-speed crosspoint switch fabric on selected lanes 13 - Two PCI Express slots with side-band connector supporting 14 - SGMII 15 - XAUI 16 - HiGig 17 - I-pass connectors allow board-to-board and loopback support 18 Two “back side” banks dedicated to other protocols 19 - High-speed crosspoint switch fabric on all lanes 20 - Four PCI Express slots with side-band connector supporting 21 - PCI Express 3.0 22 - SATA 2.0 23 - SRIO 2.0 24 - Supports 4X Aurora debug with two connectors 25 DDR Controllers 26 Three independant 64-bit DDR3 controllers 27 Supports rates of 1866 up to 2133 MHz data-rate 28 Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller 29 DDR power supplies 1.5V to all devices with automatic tracking of VTT. 30 Power software-switchable to 1.35V if software detects all DDR3LP devices. 31 MT9JSF25672AZ-2G1KZESZF has been tested at 1333, 1600, 1867, 2000 and 32 2133MT/s speeds. For 1867MT/s and above, read-to-write turnaround time 33 increases by 1 clock. 34 35 IFC/Local Bus 36 NAND flash: 8-bit, async or sync, up to 2GB. 37 NOR: 16-bit, Address/Data Multiplexed (ADM), up to 128 MB 38 NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB 39 - NOR devices support 16 virtual banks 40 GASIC: Minimal target within Qixis FPGA 41 PromJET rapid memory download support 42 Address demultiplexing handled within FPGA. 43 - Flexible demux allows 8 or 16 bit evaluation. 44 IFC Debug/Development card 45 - Support for 32-bit devices 46 Ethernet 47 Support two on-board RGMII 10/100/1G ethernet ports. 48 SGMII and XAUI support via SERDES block (see above). 49 1588 support via Symmetricom board. 50 QIXIS System Logic FPGA 51 Manages system power and reset sequencing 52 Manages DUT, board, clock, etc. configuration for dynamic shmoo 53 Collects V-I-T data in background for code/power profiling. 54 Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion) 55 General fault monitoring and logging 56 Runs from ATX “hot” power rails allowing operation while system is off. 57 Clocks 58 System and DDR clock (SYSCLK, “DDRCLK”) 59 - Switch selectable to one of 16 common settings in the interval 33MHz-166MHz. 60 - Software selectable in 1MHz increments from 1-200MHz. 61 SERDES clocks 62 - Provides clocks to all SerDes blocks and slots 63 - 100, 125 and 156.25 MHz 64 Power Supplies 65 Dedicated regulators for VDD 66 - Adjustable from (0.7V to 1.3V at 80A 67 - Regulators can be controlled by VID and/or software 68 Dedicated regulator for GVDD_PL: 1.35/1.5V at 22A 69 - VTT/MVREF automatically track operating voltage 70 Dedicated regulators/filters for AVDD supplies 71 Dedicated regulators for other supplies: OVDD, BVDD, DVDD, LVDD, POVDD, etc. 72 USB 73 Supports two USB 2.0 ports with integrated PHYs 74 - One type A, one type micro-AB with 1.0A power per port. 75 Other IO 76 eSDHC/MMC 77 - SDHC card slot 78 eSPI port 79 - High-speed serial flash 80 Two Serial port 81 Four I2C ports 82 XFI 83 XFI is supported on T4QDS-XFI board which removed slot3 and routed 84 four Lanes A/B/C/D to a SFP+ cages, which to house fiber cable or 85 direct attach cable(copper), the copper cable is used to emulate 86 10GBASE-KR scenario. 87 So, for XFI usage, there are two scenarios, one will use fiber cable, 88 another will use copper cable. An hwconfig env "fsl_10gkr_copper" is 89 introduced to indicate a XFI port will use copper cable, and U-Boot 90 will fixup the dtb accordingly. 91 It's used as: fsl_10gkr_copper:<10g_mac_name> 92 The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2, they 93 do not have to be coexist in hwconfig. If a MAC is listed in the env 94 "fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable 95 will be used by default. 96 for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2" in 97 hwconfig, then both four XFI ports will use copper cable. 98 set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two 99 XFI ports will use copper cable, the other two XFI ports will use fiber 100 cable. 101 102Memory map 103---------- 104The addresses in brackets are physical addresses. 105 1060x0_0000_0000 (0x0_0000_0000) - 0x0_7fff_ffff 2GB DDR (more than 2GB is initialized but not mapped under with TLB) 1070x0_8000_0000 (0xc_0000_0000) - 0x0_dfff_ffff 1.5GB PCIE memory 1080x0_f000_0000 (0xf_0000_0000) - 0x0_f1ff_ffff 32MB DCSR (includes trace buffers) 1090x0_f400_0000 (0xf_f400_0000) - 0x0_f5ff_ffff 32MB BMan 1100x0_f600_0000 (0xf_f600_0000) - 0x0_f7ff_ffff 32MB QMan 1110x0_f800_0000 (0xf_f800_0000) - 0x0_f803_ffff 256KB PCIE IO 1120x0_e000_0000 (0xf_e000_0000) - 0x0_efff_ffff 256MB NOR flash 1130x0_fe00_0000 (0xf_fe00_0000) - 0x0_feff_ffff 16MB CCSR 1140x0_ffdf_0000 (0xf_ffdf_0000) - 0x0_ffdf_03ff 4KB QIXIS 1150x0_ffff_f000 (0x0_7fff_fff0) - 0x0_ffff_ffff 4KB Boot page translation for secondary cores 116 117The physical address of the last (boot page translation) varies with the actual DDR size. 118 119Voltage ID and VDD override 120-------------------- 121T4240 has a VID feature. U-Boot reads the VID efuses and adjust the voltage 122accordingly. The voltage can also be override by command vdd_override. The 123syntax is 124 125vdd_override <voltage in mV>, eg. 1050 is for 1.050v. 126 127Upon success, the actual voltage will be read back. The value is checked 128for safety and any invalid value will not adjust the voltage. 129 130Another way to override VDD is to use environmental variable, in case of using 131command is too late for some debugging. The syntax is 132 133setenv t4240qds_vdd_mv <voltage in mV> 134saveenv 135reset 136 137The override voltage takes effect when booting. 138 139Note: voltage adjustment needs to be done step by step. Changing voltage too 140rapidly may cause current surge. The voltage stepping is done by software. 141Users can set the final voltage directly. 142 1432-stage NAND/SD boot loader 144------------------------------- 145PBL initializes the internal SRAM and copy SPL(160K) in SRAM. 146SPL further initialise DDR using SPD and environment variables 147and copy U-Boot(768 KB) from NAND/SD device to DDR. 148Finally SPL transers control to U-Boot for futher booting. 149 150SPL has following features: 151 - Executes within 256K 152 - No relocation required 153 154Run time view of SPL framework 155------------------------------------------------- 156|Area | Address | 157------------------------------------------------- 158|SecureBoot header | 0xFFFC0000 (32KB) | 159------------------------------------------------- 160|GD, BD | 0xFFFC8000 (4KB) | 161------------------------------------------------- 162|ENV | 0xFFFC9000 (8KB) | 163------------------------------------------------- 164|HEAP | 0xFFFCB000 (50KB) | 165------------------------------------------------- 166|STACK | 0xFFFD8000 (22KB) | 167------------------------------------------------- 168|U-Boot SPL | 0xFFFD8000 (160KB) | 169------------------------------------------------- 170 171NAND Flash memory Map on T4QDS 172-------------------------------------------------------------- 173Start End Definition Size 1740x000000 0x0FFFFF U-Boot img 1MB 1750x140000 0x15FFFF U-Boot env 128KB 1760x160000 0x17FFFF FMAN Ucode 128KB 177 178Micro SD Card memory Map on T4QDS 179---------------------------------------------------- 180Block #blocks Definition Size 1810x008 2048 U-Boot img 1MB 1820x800 0016 U-Boot env 8KB 1830x820 0128 FMAN ucode 64KB 184 185Switch Settings: (ON is 1, OFF is 0) 186=============== 187NAND boot SW setting: 188SW1[1:8] = 10000010 189SW2[1.1] = 0 190SW6[1:4] = 1001 191 192SD boot SW setting: 193SW1[1:8] = 00100000 194SW2[1.1] = 0 195